Study guide
2.4 Nonmotorized Facilities Analysis
PE Civil: Transportation Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Project Management
1.1 Quantity and Cost Estimating 1.2 Project Scheduling and CPM 1.3 Engineering Economic Analysis
2 Chapter 2: Traffic Engineering - Capacity and Flow
2.1 Uninterrupted Flow Capacity and Level of Service (LOS) 2.2 Interrupted Flow on Segment Streets 2.3 Intersection Capacity and LOS 2.4 Nonmotorized Facilities Analysis
3 Chapter 3: Traffic Engineering - Studies and Safety
3.1 Traffic Volume, Speed, and Planning Studies 3.2 Traffic Forecasts and Monitoring 3.3 Traffic Safety and Collision Analysis 3.4 Highway Safety and Crash Modification Factors (CMFs)
4 Chapter 4: Roadside and Cross-Section Design
4.1 Forgiving Roadside and Clear Zone Design 4.2 Barrier Design and Length of Need 4.3 Cross-Section Design Elements 4.4 Nonmotorized Design Considerations
5 Chapter 5: Horizontal Alignment Design
5.1 Circular Curve Elements and Calculations 5.2 Design Speed and Superelevation Design 5.3 Horizontal Sight Distance and Obstructions
6 Chapter 6: Vertical Alignment Design
6.1 Grades, Slopes, and Profile Design 6.2 Crest Vertical Curve Geometry and Sight Distance 6.3 Sag Vertical Curve Geometry and Sight Distance 6.4 Vertical Clearance Under Structures
7 Chapter 7: Intersection Geometry and Layout
7.1 At-Grade Intersection Design and Roundabouts 7.2 Intersection Sight Distance and Sight Triangles 7.3 Interchange Ramps and Terminal Geometry
8 Chapter 8: Traffic Signals
8.1 Traffic Signal Timing and Phasing 8.2 Traffic Signal Warrants (MUTCD) 8.3 Traffic Signal Design and Preemption
9 Chapter 9: Traffic Control Design
9.1 Permanent Signing Design and Standards 9.2 Pavement Marking Layout and Rules 9.3 Temporary Traffic Control and Work Zones
10 Chapter 10: Geotechnical and Pavements
10.1 Sampling, Testing, and Soil Stabilization 10.2 Fundamental Soil Properties and Mass Balance 10.3 Compaction, Excavation, and Mass Diagrams 10.4 Flexible and Rigid Pavement Design and ESALs
11 Chapter 11: Hydrology and Open-Channel Drainage
11.1 Rainfall Hydrology and Rational Method 11.2 Open-Channel Flow and Manning's Equation 11.3 Peak Flow Mitigation and Water-Quality
12 Chapter 12: Drainage Structures and Systems
12.1 Culvert Design and Inlet/Outlet Control 12.2 Stormwater Collection Systems and Inlet Capacities
2.4 Nonmotorized Facilities Analysis
Key Takeaways Explain This Topic AI
Pedestrian space (M), measured in square feet per pedestrian, is the primary service measure for walkways and sidewalks.
Effective sidewalk width (W_E) is calculated by subtracting physical obstructions and shy distances from the total physical width: W_E = W_T − W_O.
The standard walking speed used for pedestrian clearance time at traffic signals is 3.5 ft/s to accommodate children and elderly pedestrians.
Bicycle Level of Service (BLOS) is a comfort-based score modeled on lane configurations, traffic speeds/volumes, heavy vehicle percentage, and pavement condition (PCI).
Last updated: July 2026
Introduction to Nonmotorized Facilities
In modern transportation engineering, facility design and evaluation have shifted from purely vehicle-centric metrics to multimodal analysis. The Highway Capacity Manual (HCM) provides guidelines for evaluating the performance of nonmotorized facilities, specifically focusing on pedestrian and bicycle operations. Analyzing these facilities is essential for creating safe, complete streets, and is a key topic on the NCEES PE Civil Transportation exam.
Pedestrian Walkway and Sidewalk Analysis
The operational analysis of pedestrian walkways evaluates sidewalks, paths, and plazas. The performance is assessed using pedestrian speed, flow rate, and density. The primary service measure for walkways is pedestrian space ( M M M ) , measured in square feet per pedestrian ( f t 2 / p e d ft^2/ped f t 2 / p e d ).
Effective Sidewalk Width ( W E W_E W E )
Pedestrians do not use the entire physical width of a sidewalk. Part of the sidewalk is occupied by physical obstructions (benches, trees, light poles, parking meters), and pedestrians naturally maintain a "shy distance" from building walls and roadway curbs. The effective sidewalk width ( W E W_E W E ) is calculated as:
W_E = W_T − W_O
Where:
W_T = Total physical width of the sidewalk (ft).
W_O = Width of obstructions plus shy distances (ft). Standard shy distance offsets include 1.5 ft from building faces and 1.0 to 1.5 ft from curbs.
Pedestrian Unit Flow Rate (v_p)
The pedestrian flow rate represents the number of pedestrians passing a point per unit of width per minute. It is calculated as:
v_p = V_p / W_E
Where:
v_p = Pedestrian unit flow rate (ped/min/ft).
V_p = Pedestrian volume (ped/min).
W_E = Effective sidewalk width (ft).
Pedestrian Speed (S_p) and Space (M)
Walking Speed (S_p): The average walking speed under unimpeded conditions is typically taken as 4.0 ft/s (240 ft/min) . For design purposes, particularly signal timing, a speed of 3.5 ft/s is used to accommodate slower pedestrians, such as children and older adults.
Pedestrian Space (M): The average area available to each pedestrian, calculated as the inverse of density. It is computed from walking speed and flow rate:
M = (S_p × 60) / v_p
Where S_p is in ft/s and v_p is in ped/min/ft. (For example, if S_p = 4.0 ft/s and v_p = 20 ped/min/ft, then M = 240 / 20 = 12.0 sq ft/ped).
Pedestrian Level of Service (PLOS) for Walkways
The PLOS for sidewalks is determined directly by the average pedestrian space (M):
Level of Service (LOS) Pedestrian Space (M) (ft^2/ped) Operational Description
A > 60 Unimpeded path choice; no conflicts; walking speed is bypass-free.
B > 40 to 60 Minor restriction in path selection; walking speed is stable.
C > 24 to 40 Path selection is restricted; overtaking slower pedestrians is difficult.
D > 15 to 24 Walking speed is restricted; high probability of minor conflicts.
E > 8 to 15 Space is severely restricted; speed is limited; frequent conflicts.
F <= 8 Forced flow; walking speed is stop-and-go; frequent physical contact.
Pedestrian Platoon Flow
In urban environments, pedestrians do not arrive uniformly. They frequently travel in platoons (groups) due to traffic signal releases or transit arrivals. Platoon flow analysis evaluates the localized peak density within the group. The platoon flow rate is higher than the average hourly flow rate, resulting in a significantly smaller pedestrian space. HCM guidelines suggest using platoon flow rates for high-density transit corridors and CBD areas to ensure adequate sidewalk sizing.
Crosswalk Design and Signal Requirements
At intersections, crosswalks must accommodate pedestrians waiting to cross and those crossing during the green phase.
Pedestrian Clearance Time (t_p)
The traffic signal must provide sufficient green time (or flashing "Don't Walk" time, known as the Pedestrian Clearance Interval) to allow a pedestrian starting from the curb to cross the entire width of the street. The required clearance time is calculated as:
t_p = d_c / S_p
Where:
d_c = Pedestrian crossing distance, measured from the curb to the center of the farthest travel lane (ft).
S_p = Walking speed (typically 3.5 ft/s per the MUTCD standard).
Additionally, the MUTCD requires a minimum Walk Interval (t_w) of 7.0 seconds (which can be reduced to 4.0 seconds in rare cases) to allow pedestrians to step into the crosswalk before the clearance interval begins.
Corner Storage Area
Intersection corners serve as storage reservoirs for pedestrians waiting for a walk signal. The corner reservoir capacity is analyzed based on the available area and the peak number of waiting pedestrians, targeting a minimum of 5.0 to 10.0 sq ft per pedestrian to maintain acceptable operations.
Bicycle Level of Service (BLOS)
Unlike vehicular or pedestrian LOS, which are determined by physical service measures like delay or space, Bicycle Level of Service (BLOS) is a model-based index that represents the average bicyclist's perception of comfort and safety on a roadway segment.
Factors Influencing BLOS
The BLOS score is calculated using regression models based on empirical passenger studies. Key factors include:
Bicycle Lane Width: Wider bike lanes, paved shoulders, and outside travel lanes significantly improve comfort.
Motorized Vehicle Volume and Speed: High volumes and higher travel speeds of adjacent vehicles reduce comfort.
Heavy Vehicles: A higher percentage of trucks/buses decreases bicyclist comfort due to wind turbulence and perceived risk.
Pavement Condition: Roadway surface roughness (represented by the Pavement Condition Index, PCI) has a substantial impact; rough or cracked pavement reduces bicyclist comfort.