Study guide
3.1 Traffic Volume, Speed, and Planning Studies
PE Civil: Transportation Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Project Management
1.1 Quantity and Cost Estimating 1.2 Project Scheduling and CPM 1.3 Engineering Economic Analysis
2 Chapter 2: Traffic Engineering - Capacity and Flow
2.1 Uninterrupted Flow Capacity and Level of Service (LOS) 2.2 Interrupted Flow on Segment Streets 2.3 Intersection Capacity and LOS 2.4 Nonmotorized Facilities Analysis
3 Chapter 3: Traffic Engineering - Studies and Safety
3.1 Traffic Volume, Speed, and Planning Studies 3.2 Traffic Forecasts and Monitoring 3.3 Traffic Safety and Collision Analysis 3.4 Highway Safety and Crash Modification Factors (CMFs)
4 Chapter 4: Roadside and Cross-Section Design
4.1 Forgiving Roadside and Clear Zone Design 4.2 Barrier Design and Length of Need 4.3 Cross-Section Design Elements 4.4 Nonmotorized Design Considerations
5 Chapter 5: Horizontal Alignment Design
5.1 Circular Curve Elements and Calculations 5.2 Design Speed and Superelevation Design 5.3 Horizontal Sight Distance and Obstructions
6 Chapter 6: Vertical Alignment Design
6.1 Grades, Slopes, and Profile Design 6.2 Crest Vertical Curve Geometry and Sight Distance 6.3 Sag Vertical Curve Geometry and Sight Distance 6.4 Vertical Clearance Under Structures
7 Chapter 7: Intersection Geometry and Layout
7.1 At-Grade Intersection Design and Roundabouts 7.2 Intersection Sight Distance and Sight Triangles 7.3 Interchange Ramps and Terminal Geometry
8 Chapter 8: Traffic Signals
8.1 Traffic Signal Timing and Phasing 8.2 Traffic Signal Warrants (MUTCD) 8.3 Traffic Signal Design and Preemption
9 Chapter 9: Traffic Control Design
9.1 Permanent Signing Design and Standards 9.2 Pavement Marking Layout and Rules 9.3 Temporary Traffic Control and Work Zones
10 Chapter 10: Geotechnical and Pavements
10.1 Sampling, Testing, and Soil Stabilization 10.2 Fundamental Soil Properties and Mass Balance 10.3 Compaction, Excavation, and Mass Diagrams 10.4 Flexible and Rigid Pavement Design and ESALs
11 Chapter 11: Hydrology and Open-Channel Drainage
11.1 Rainfall Hydrology and Rational Method 11.2 Open-Channel Flow and Manning's Equation 11.3 Peak Flow Mitigation and Water-Quality
12 Chapter 12: Drainage Structures and Systems
12.1 Culvert Design and Inlet/Outlet Control 12.2 Stormwater Collection Systems and Inlet Capacities
3.1 Traffic Volume, Speed, and Planning Studies
Key Takeaways Explain This Topic AI
The Design Hourly Volume (DHV) represents the 30th highest hourly volume of the year ( 30 D H V 30DHV 30 DH V ), representing a balance between capacity and economy.
Space Mean Speed (SMS) is the harmonic mean of vehicle speeds and is always less than or equal to the Time Mean Speed (TMS), which is the arithmetic mean.
The 85th percentile speed is the primary statistical metric used to establish legal speed limits under free-flowing conditions.
The Moving Observer Method allows a single test vehicle to determine both the average traffic volume and mean travel time for a roadway segment.
Last updated: July 2026
- 3.1 Traffic Volume, Speed, and Planning Studies
- Traffic Volume Metrics and Calculations
Traffic volume is the number of vehicles passing a given point on a roadway during a specified time interval. In traffic engineering, volumes are normalized over different time frames to assist in planning, design, and operations.
Average Daily Traffic (ADT) and Annual Average Daily Traffic (AADT)
Average Daily Traffic (ADT): The average number of vehicles passing a point during a period of time greater than one day and less than one year (typically 2 to 7 days). It is calculated as: A D T = Total Volume during Period Number of Days in Period ADT = \frac{\text{Total Volume during Period}}{\text{Number of Days in Period}} A D T = Number of Days in Period Total Volume during Period
Annual Average Daily Traffic (AADT): The average number of vehicles passing a point daily over a full year (365 days). It is computed as: A A D T = Total Volume in one Year 365 AADT = \frac{\text{Total Volume in one Year}}{365} AA D T = 365 Total Volume in one Year
Because count programs cannot run continuously at all locations, short-term coverage counts (e.g., 48 hours) are adjusted to estimate AADT using monthly ( M F MF MF ), seasonal ( S F SF SF ), and daily ( D F DF D F ) adjustment factors derived from nearby Permanent Traffic Recorders (PTRs): A A D T = ADT × M F × D F AADT = \text{ADT} \times MF \times DF AA D T = ADT × MF × D F
Design Hourly Volume (DHV) and Directional Design Hourly Volume (DDHV)
Designing a highway for the absolute peak hourly volume is economically infeasible, while designing for the average volume results in congestion for half the year. Engineers balance this using the Design Hourly Volume (DHV) , typically defined as the 30th highest hourly volume of the year ( 30 D H V 30DHV 30 DH V ). D H V = A A D T × K DHV = AADT \times K DH V = AA D T × K
where K K K (the proportion of daily traffic occurring during the design hour) typically ranges from:
- 0.08 0.08 0.08 to 0.12 0.12 0.12 for urban arterials
- 0.12 0.12 0.12 to 0.18 0.18 0.18 for rural highways
For multi-lane facilities, flow is directional. The Directional Design Hourly Volume (DDHV) represents the peak-direction volume during the design hour: D D H V = A A D T × K × D DDHV = AADT \times K \times D DDH V = AA D T × K × D
where D D D is the directional distribution factor, expressing the proportion of traffic traveling in the peak direction (typically 0.50 0.50 0.50 to 0.80 0.80 0.80 ).
- Metric Typical Values (Urban) Typical Values (Rural)
- K-Factor 8 % − 12 % 8\% - 12\% 8% − 12% 12 % − 18 % 12\% - 18\% 12% − 18%
- D-Factor 50 % − 60 % 50\% - 60\% 50% − 60% 65 % − 80 % 65\% - 80\% 65% − 80%
- Speed Studies: Statistical Definitions and Metrics
Speed is a key parameter in determining level of service, safety, and operational efficiency. Traffic speed studies utilize several key statistical metrics.
Time Mean Speed ( u t u_t u t ) vs. Space Mean Speed ( u s u_s u s )
Traffic speed measurements differ based on whether they are taken at a single point over time or across a space segment:
Time Mean Speed ( u t u_t u t ): The arithmetic mean of the spot speeds of all vehicles passing a point during a specified time interval: u t = 1 n ∑ i = 1 n u i u_t = \frac{1}{n} \sum_{i=1}^{n} u_i u t = n 1 i = 1 ∑ n u i
Space Mean Speed ( u s u_s u s ): The harmonic mean of the speeds of all vehicles occupying a given section of road over a specified time interval. It represents the ratio of travel distance ( L L L ) to average travel time ( t i t_i t i ): u s = n ∑ i = 1 n 1 u i = n ⋅ L ∑ i = 1 n t i u_s = \frac{n}{\sum_{i=1}^{n} \frac{1}{u_i}} = \frac{n \cdot L}{\sum_{i=1}^{n} t_i} u s = ∑ i = 1 n u i 1 n = ∑ i = 1 n t i n ⋅ L
Space mean speed is always less than or equal to time mean speed ( u s ≤ u t u_s \le u_t u s ≤ u t ). The difference decreases as the variance in vehicle speeds ( σ s 2 \sigma_s^2 σ s 2 ) approaches zero: ν t = u s + σ s 2 u s \nu_t = u_s + \frac{\sigma_s^2}{u_s} ν t = u s + u s σ s 2
In capacity analysis and traffic flow theory ( q = k ⋅ u q = k \cdot u q = k ⋅ u ), the space mean speed u s u_s u s must be used, as time mean speed will overestimate density.
Percentile Speeds
In spot speed studies, individual speeds are plotted as a cumulative frequency distribution:
85th Percentile Speed: The speed at or below which 85% of vehicles travel. It is the primary engineering standard used to set regulatory speed limits.
15th Percentile Speed: The speed at or below which 15% of vehicles travel. Often used to determine minimum speed limits or identify slow-moving hazards.
50th Percentile Speed (Median): The speed representing the middle of the distribution.
Travel Time and Delay Studies: Moving Observer Method
The Moving Observer Method (or moving vehicle technique) is a field study method to determine average volume, density, and travel time along a segment using a single test vehicle. The test vehicle makes multiple runs in both directions (with and against the flow of interest).
Let the direction of interest be the westbound direction. The test vehicle makes runs going westbound (with the traffic, subscript w w w ) and eastbound (against the traffic, subscript a a a ). The following values are recorded:
t w , t a t_w, t_a t w , t a : Travel times of the test vehicle with and against the stream, respectively.
x x x : Number of vehicles met by the test vehicle when traveling against the stream (eastbound).
o o o : Number of vehicles that overtake the test vehicle when traveling with the stream (westbound).
p p p : Number of vehicles that the test vehicle overtakes when traveling with the stream (westbound).
y y y : Net overtakes, where y = o − p y = o - p y = o − p .
The hourly flow rate ( q q q ) in the direction of interest (westbound) is calculated as: q = x + y t w + t a q = \frac{x + y}{t_w + t_a} q = t w + t a x + y
The average travel time ( t ˉ \bar{t} t ˉ ) of the traffic stream in the direction of interest is: t ˉ = t w − y q \bar{t} = t_w - \frac{y}{q} t ˉ = t w − q y
Once flow ( q q q ) and average travel time ( t ˉ \bar{t} t ˉ ) are known, the density ( k k k ) of the segment is found using the fundamental relationship: k = q u s = q ⋅ t ˉ L k = \frac{q}{u_s} = \frac{q \cdot \bar{t}}{L} k = u s q = L q ⋅ t ˉ
Trip Generation and Modal Split
Transportation planning utilizes a macro-level approach to predict travel behavior.
Trip Generation
Trip generation models estimate the number of trip productions ( P P P ) and attractions ( A A A ) for each Traffic Analysis Zone (TAZ). It uses linear regression or cross-classification: T = a + b ⋅ X T = a + b \cdot X T = a + b ⋅ X
where T T T is the number of trips, X X X is an independent variable (e.g., household size, employment count), and a , b a, b a , b are calibration coefficients.
Modal Split (Mode Choice)
Modal split models predict the proportion of travelers choosing a specific mode (e.g., auto, transit, walking). The multinomial logit model is the industry standard: P ( i ) = e U i ∑ j = 1 m e U j P(i) = \frac{e^{U_i}}{\sum_{j=1}^{m} e^{U_j}} P ( i ) = ∑ j = 1 m e U j e U i
where P ( i ) P(i) P ( i ) is the probability of choosing mode i i i , and U i U_i U i is the utility function of mode i i i (commonly a function of travel time, cost, and comfort parameters): U i = a i − β 1 ( Time i ) − β 2 ( Cost i ) U_i = a_i - \beta_1 (\text{Time}_i) - \beta_2 (\text{Cost}_i) U i = a i − β 1 ( Time i ) − β 2 ( Cost i )