Study guide

6.3 Sag Vertical Curve Geometry and Sight Distance

PE Civil: Transportation Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Project Management

1.1 Quantity and Cost Estimating 1.2 Project Scheduling and CPM 1.3 Engineering Economic Analysis

2 Chapter 2: Traffic Engineering - Capacity and Flow

2.1 Uninterrupted Flow Capacity and Level of Service (LOS) 2.2 Interrupted Flow on Segment Streets 2.3 Intersection Capacity and LOS 2.4 Nonmotorized Facilities Analysis

3 Chapter 3: Traffic Engineering - Studies and Safety

3.1 Traffic Volume, Speed, and Planning Studies 3.2 Traffic Forecasts and Monitoring 3.3 Traffic Safety and Collision Analysis 3.4 Highway Safety and Crash Modification Factors (CMFs)

4 Chapter 4: Roadside and Cross-Section Design

4.1 Forgiving Roadside and Clear Zone Design 4.2 Barrier Design and Length of Need 4.3 Cross-Section Design Elements 4.4 Nonmotorized Design Considerations

5 Chapter 5: Horizontal Alignment Design

5.1 Circular Curve Elements and Calculations 5.2 Design Speed and Superelevation Design 5.3 Horizontal Sight Distance and Obstructions

6 Chapter 6: Vertical Alignment Design

6.1 Grades, Slopes, and Profile Design 6.2 Crest Vertical Curve Geometry and Sight Distance 6.3 Sag Vertical Curve Geometry and Sight Distance 6.4 Vertical Clearance Under Structures

7 Chapter 7: Intersection Geometry and Layout

7.1 At-Grade Intersection Design and Roundabouts 7.2 Intersection Sight Distance and Sight Triangles 7.3 Interchange Ramps and Terminal Geometry

8 Chapter 8: Traffic Signals

8.1 Traffic Signal Timing and Phasing 8.2 Traffic Signal Warrants (MUTCD) 8.3 Traffic Signal Design and Preemption

9 Chapter 9: Traffic Control Design

9.1 Permanent Signing Design and Standards 9.2 Pavement Marking Layout and Rules 9.3 Temporary Traffic Control and Work Zones

10 Chapter 10: Geotechnical and Pavements

10.1 Sampling, Testing, and Soil Stabilization 10.2 Fundamental Soil Properties and Mass Balance 10.3 Compaction, Excavation, and Mass Diagrams 10.4 Flexible and Rigid Pavement Design and ESALs

11 Chapter 11: Hydrology and Open-Channel Drainage

11.1 Rainfall Hydrology and Rational Method 11.2 Open-Channel Flow and Manning's Equation 11.3 Peak Flow Mitigation and Water-Quality

12 Chapter 12: Drainage Structures and Systems

12.1 Culvert Design and Inlet/Outlet Control 12.2 Stormwater Collection Systems and Inlet Capacities

6.3 Sag Vertical Curve Geometry and Sight Distance

Key Takeaways Explain This Topic AI

Sag vertical curves connect a downgrade to an upgrade or a gentler downgrade, forming a concave profile.

The design length of sag vertical curves is governed by headlight sight distance, passenger comfort, drainage, and general appearance.

For headlight control (US Customary), the minimum curve length is L = A*S^2 / (400 + 3.5S) for S <= L.

Passenger comfort criteria limits vertical centripetal acceleration to 1 ft/s^2, yielding the minimum length L = A*V^2 / 46.5.

The low point location on a sag curve occurs at xm = |G1| * L / A from the PVC, which is critical for placing drainage inlets.

Last updated: July 2026

  • 6.3 Sag Vertical Curve Geometry and Sight Distance
  • Geometry of Sag Curves

A sag vertical curve is a concave vertical transition between two tangent grades. Sag curves are used when connecting a downgrade to an upgrade, a downgrade to a gentler downgrade, or an upgrade to a steeper upgrade. Like crest curves, they are modeled as equal-tangent parabolas, splitting the horizontal curve length ( L L L ) equally on either side of the Point of Vertical Intersection (PVI).

The rate of vertical curvature ( K = L / A K = L/A K = L / A ) remains a core design parameter. However, unlike crest curves, where design is almost exclusively governed by stopping sight distance, sag vertical curve design is controlled by four separate criteria:

Headlight Sight Distance (Safety) : The primary night safety driver.

Passenger Comfort : Preventing excessive vertical centripetal force.

Drainage Control : Preventing water pooling at the bottom of curbed sections.

General Appearance : Aesthetics and driver anticipation.

Headlight Sight Distance Criteria

During daylight hours, a driver's sight distance on a sag curve is generally unrestricted unless blocked by an overhead structure (such as a bridge). However, at night, the sight distance is limited by the area of the roadway illuminated by the vehicle's headlights.

Mathematical Formulation

To model night sight distance, AASHTO assumes:

The height of the headlight above the roadway surface is h 3 = 2.0 ft h_3 = 2.0\text{ ft} h 3 ​ = 2.0 ft ( 0.60 m 0.60\text{ m} 0.60 m ).

The headlight beam has an upward divergence angle (spread) of θ = 1.0 ∘ \theta = 1.0^\circ θ = 1. 0 ∘ above the longitudinal axis of the vehicle.

Case 1: Sight Distance is Less Than or Equal to Curve Length ( S ≤ L S \le L S ≤ L )

The minimum curve length is given by: L = A S 2 200 ( h 3 + S tan ⁡ θ ) L = \frac{A S^2}{200 \left( h_3 + S \tan \theta \right)} L = 200 ( h 3 ​ + S tan θ ) A S 2 ​

Substituting h 3 = 2.0 ft h_3 = 2.0\text{ ft} h 3 ​ = 2.0 ft and θ = 1.0 ∘ \theta = 1.0^\circ θ = 1. 0 ∘ :

  • US Customary Units : L = A S 2 400 + 3.5 S L = \frac{A S^2}{400 + 3.5S} L = 400 + 3.5 S A S 2 ​
  • Metric Units : L = A S 2 120 + 3.5 S L = \frac{A S^2}{120 + 3.5S} L = 120 + 3.5 S A S 2 ​
  • Case 2: Sight Distance is Greater Than Curve Length ( S > L S > L S > L )

If the required sight distance exceeds the curve length: L = 2 S − 200 ( h 3 + S tan ⁡ θ ) A L = 2S - \frac{200 \left( h_3 + S \tan \theta \right)}{A} L = 2 S − A 200 ( h 3 ​ + S tan θ ) ​

Substituting standard design values:

  • US Customary Units : L = 2 S − 400 + 3.5 S A L = 2S - \frac{400 + 3.5S}{A} L = 2 S − A 400 + 3.5 S ​
  • Metric Units : L = 2 S − 120 + 3.5 S A L = 2S - \frac{120 + 3.5S}{A} L = 2 S − A 120 + 3.5 S ​
  • Passenger Comfort Criteria

When a vehicle travels through a sag vertical curve, centripetal acceleration acts downward, adding to the force of gravity. If this vertical acceleration is too high, passenger discomfort occurs (a feeling of being "pushed" into the seat).

To ensure comfort, AASHTO limits vertical centripetal acceleration to 1.0 ft/s 2 1.0\text{ ft/s}^2 1.0 ft/s 2 ( 0.3 m/s 2 0.3\text{ m/s}^2 0.3 m/s 2 ). The minimum curve length required to satisfy comfort is:

  • US Customary Units : L = A V 2 46.5 L = \frac{A V^2}{46.5} L = 46.5 A V 2 ​
  • Metric Units : L = A v 2 395 L = \frac{A v^2}{395} L = 395 A v 2 ​

Where:

  • V V V = Design speed in mph
  • v v v = Design speed in km/h
  • A A A = Algebraic difference in grades (in percent)
  • Drainage Criteria

On curbed roadways, sag vertical curves present a drainage challenge. At the very bottom of the curve, the grade passes through 0.0 % 0.0\% 0.0% . If the curve is too long (too flat near the bottom), stormwater will not drain quickly to the gutters, leading to water accumulation and hydroplaning risks.

To maintain adequate drainage on curbed roads, a minimum longitudinal slope of 0.3 % 0.3\% 0.3% must be maintained within 50 feet of the low point. This requirement is met if the rate of vertical curvature ( K K K ) satisfies: K ≤ 167 ft/% grade K \le 167\text{ ft/\% grade} K ≤ 167 ft/% grade

Thus, for drainage, we have a maximum length limit ( L max ⁡ = 167 ⋅ A L_{\max} = 167 \cdot A L m a x ​ = 167 ⋅ A ) rather than a minimum length limit. If the calculated design curve length exceeds this maximum, designers must specify special gutter profiles or closely spaced catch basins.

Low Point Location and Elevation

Locating the lowest point of a sag vertical curve is vital for placing catch basins to collect runoff.

Station of the Low Point

The horizontal distance ( x m x_m x m ​ ) from the PVC to the low point on an equal-tangent parabolic curve is: x m = ∣ G 1 ∣ L ∣ G 2 − G 1 ∣ = ∣ G 1 ∣ L A x_m = \frac{|G_1| L}{|G_2 - G_1|} = \frac{|G_1| L}{A} x m ​ = ∣ G 2 ​ − G 1 ​ ∣ ∣ G 1 ​ ∣ L ​ = A ∣ G 1 ​ ∣ L ​

Where:

  • G 1 G_1 G 1 ​ = Slope of the entering tangent (in percent)
  • L L L = Total length of the curve
  • A A A = Algebraic difference in grades ( ∣ G 2 − G 1 ∣ |G_2 - G_1| ∣ G 2 ​ − G 1 ​ ∣ )

Note: The low point only lies within the curve if the tangents slope in opposite directions (one negative, one positive). If both are positive, the low point is at the PVC ( x m = 0 x_m = 0 x m ​ = 0 ). If both are negative, the low point is at the PVT ( x m = L x_m = L x m ​ = L ).

The station of the low point is: Sta L P = Sta P V C + x m \text{Sta}_{LP} = \text{Sta}_{PVC} + x_m Sta L P ​ = Sta P V C ​ + x m ​

Elevation of the Low Point

The elevation of the low point ( E L P E_{LP} E L P ​ ) is calculated by applying the parabolic elevation equation: E L P = E P V C + ( G 1 100 ) x m + A x m 2 200 L E_{LP} = E_{PVC} + \left( \frac{G_1}{100} \right) x_m + \frac{A x_m^2}{200 L} E L P ​ = E P V C ​ + ( 100 G 1 ​ ​ ) x m ​ + 200 L A x m 2 ​ ​

Alternatively, using the absolute value of G 1 G_1 G 1 ​ in percent, the shortcut formula is: E L P = E P V C − G 1 2 L 200 A E_{LP} = E_{PVC} - \frac{G_1^2 L}{200 A} E L P ​ = E P V C ​ − 200 A G 1 2 ​ L ​

Step-by-Step Design Example

A sag vertical curve connects a − 3.0 % -3.0\% − 3.0% grade to a + 2.0 % +2.0\% + 2.0% grade. The design speed is 50 mph, requiring a stopping sight distance of 425 feet. The PVC is at station 10 + 00 10+00 10 + 00 and elevation 100.00 ft 100.00\text{ ft} 100.00 ft .

Calculate Grade Difference (A) : A = ∣ 2.0 − ( − 3.0 ) ∣ = 5.0 % A = |2.0 - (-3.0)| = 5.0\% A = ∣2.0 − ( − 3.0 ) ∣ = 5.0%

Verify Length for Headlight Sight Distance :

Assume S ≤ L S \le L S ≤ L : L = A S 2 400 + 3.5 S = 5.0 ⋅ 425 2 400 + 3.5 ( 425 ) = 903 , 125 1887.5 ≈ 478.5 ft L = \frac{A S^2}{400 + 3.5S} = \frac{5.0 \cdot 425^2}{400 + 3.5(425)} = \frac{903,125}{1887.5} \approx 478.5\text{ ft} L = 400 + 3.5 S A S 2 ​ = 400 + 3.5 ( 425 ) 5.0 ⋅ 42 5 2 ​ = 1887.5 903 , 125 ​ ≈ 478.5 ft Since 425 ft ≤ 478.5 ft 425\text{ ft} \le 478.5\text{ ft} 425 ft ≤ 478.5 ft , the assumption is correct. The minimum curve length for headlight sight distance is 479 feet .

Verify Length for Comfort : L c = A V 2 46.5 = 5.0 ⋅ 50 2 46.5 = 12 , 500 46.5 ≈ 268.8 ft L_c = \frac{A V^2}{46.5} = \frac{5.0 \cdot 50^2}{46.5} = \frac{12,500}{46.5} \approx 268.8\text{ ft} L c ​ = 46.5 A V 2 ​ = 46.5 5.0 ⋅ 5 0 2 ​ = 46.5 12 , 500 ​ ≈ 268.8 ft Since headlight control requires a longer curve ( 479 ft > 269 ft 479\text{ ft} > 269\text{ ft} 479 ft > 269 ft ), headlight control governs. Let's round the design curve length to 500 ft 500\text{ ft} 500 ft .

Locate the Low Point : x m = ∣ G 1 ∣ L A = 3.0 ⋅ 500 5.0 = 300 ft x_m = \frac{|G_1| L}{A} = \frac{3.0 \cdot 500}{5.0} = 300\text{ ft} x m ​ = A ∣ G 1 ​ ∣ L ​ = 5.0 3.0 ⋅ 500 ​ = 300 ft Sta L P = ( 10 + 00 ) + 300 = 13 + 00 \text{Sta}_{LP} = (10+00) + 300 = 13+00 Sta L P ​ = ( 10 + 00 ) + 300 = 13 + 00

Calculate Low Point Elevation : E L P = E P V C − G 1 2 L 200 A = 100.00 − 3.0 2 ⋅ 500 200 ⋅ 5.0 = 100.00 − 4.50 = 95.50 ft E_{LP} = E_{PVC} - \frac{G_1^2 L}{200 A} = 100.00 - \frac{3.0^2 \cdot 500}{200 \cdot 5.0} = 100.00 - 4.50 = 95.50\text{ ft} E L P ​ = E P V C ​ − 200 A G 1 2 ​ L ​ = 100.00 − 200 ⋅ 5.0 3. 0 2 ⋅ 500 ​ = 100.00 − 4.50 = 95.50 ft