Study guide

19.1 Flow, Concentration, and Load Workbook

NCEES PE Civil: Water Resources and Environmental Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: NCEES WRE Exam Spec and Reference Strategy

1.1 NCEES WRE Format 1.2 Reference Handbook and Units 1.3 Blueprint Prioritization

2 Chapter 6: WRE Project Planning, Cost, and Engineering Economics

6.1 Quantity Takeoff and Unit Basis 6.2 Cost Estimating and Bid Item Logic 6.3 Schedules, Sequencing, and Critical Path 6.4 Present Worth, Life-Cycle Cost, and Sustainability

3 Chapter 7: Soil Mechanics for WRE Problems

7.1 Lateral Earth Pressure and Retaining Situations 7.2 Consolidation, Compaction, and Settlement 7.3 Bearing Capacity and Slope Stability 7.4 Soil Data, Boring Logs, and Unit Conversions

4 Chapter 8: WRE Analysis and Hydraulic Design Foundations

8.1 Mass Balance and Hydraulic Loading 8.2 Solids Loading and Sludge Mass Balance 8.3 Hydraulic Flow Measurement and Instrumentation 8.4 Design Checks, Safety Factors, and Reasonableness

5 Chapter 9: WRE Hydrology, Runoff, and Storage Routing

9.1 Design Storms, IDF, and Time of Concentration 9.2 Rational Method and Peak Flow Limits 9.3 NRCS Curve Number and Unit Hydrographs 9.4 Detention, Retention, and Routing Checks

6 Chapter 10: Closed Conduit and Open Channel Hydraulics

10.1 Continuity, Energy, and HGL/EGL 10.2 Pipe Flow Losses, Pumps, and Net Head 10.3 Manning, Open Channel, and Critical Flow 10.4 Culverts, Weirs, Orifices, and Control Sections

7 Chapter 11: Groundwater, Wells, and Aquifer Flow

11.1 Darcy Law, Gradient, and Flow Area 11.2 Confined and Unconfined Aquifers and Storage 11.3 Well Drawdown, Specific Capacity, and Interference 11.4 Contaminant Transport and Dewatering Decisions

8 Chapter 12: Water Quality Chemistry and Pollutant Loading

12.1 Concentration, Load, and Mass-Rate Conversions 12.2 BOD, CBOD, DO, and Oxygen Demand 12.3 Nutrients, pH, Alkalinity, and Buffering 12.4 Pollutant Allocation, TMDL, and Water Quality Criteria

9 Chapter 13: Water Treatment Processes and Design Checks

13.1 Coagulation, Flocculation, and Sedimentation 13.2 Filtration, Disinfection, and CT Logic 13.3 Softening, Iron, Manganese, and Chemical Feed 13.4 Treatment Plant Hydraulics and Operations

10 Chapter 14: Wastewater Collection, Treatment, and Sludge

14.1 Collection-System Hydraulics and Infiltration 14.2 Preliminary, Primary, and Secondary Treatment 14.3 Nutrient Removal and Effluent Quality 14.4 Sludge Processing, Digestion, and Dewatering

11 Chapter 3: Water Quality, Treatment, and Sitework

Water Quality and Regulation Drinking Water and Wastewater Treatment Project Sitework and Final Review

12 Chapter 15: Sitework, Drainage, and Erosion Control

15.1 Grading, Cut/Fill, and Earthwork Balancing 15.2 Storm Drain Inlets and Minor Systems 15.3 Erosion, Sediment Control, and BMPs 15.4 Permitting, Constructability, and Field Adjustments

13 Chapter 4: Materials, Analysis, and Design for WRE

4.1 Materials and Pipe Selection 4.2 Analysis and Design Workflow 4.3 Site-Civil Constructability

14 Chapter 16: Materials, Pipes, Standards, and Reference Navigation

16.1 Pipe Material Selection and Failure Modes 16.2 Concrete, Soil, and Geosynthetic Materials 16.3 Design Standard Navigation and Revision Years 16.4 Reference Search Drills and Unit Checks

15 Chapter 18: Pumps, Distribution, and Collection Systems

18.1 Pump Curves, System Curves, and Operating Point 18.2 Water Distribution Pressure, Demand, and Storage 18.3 Sewer Collection, Lift Stations, and Force Mains 18.4 Transient, Surge, and Operational Troubleshooting

16 Chapter 19: WRE Calculation Workbook and Unit Drills

19.1 Flow, Concentration, and Load Workbook 19.2 Hydraulics Energy and Head Workbook 19.3 Treatment and Process Sizing Workbook 19.4 Error Patterns and Repair Drills

17 Chapter 5: Mixed Practice, Units, and Final Review

Formula Selection and Units Mixed WRE Mock Review Exam Day and Spec Transition

18 Chapter 17: Full-Length WRE Mixed Practice and Final Review

17.1 Eighty-Question Mock Exam Plan 17.2 Miss-Log Diagnostics by Domain 17.3 Calculator, Reference, and Break Strategy 17.4 Final-Week Current vs 2027 Spec Check

19.1 Flow, Concentration, and Load Workbook

Key Takeaways Explain This Topic AI

Identify the basis (flow, concentration, mass rate, volume, area, or time) before opening the NCEES PE Civil Reference Handbook.

Memorize the load constant: lb/day = flow (MGD) x concentration (mg/L) x 8.34, where 8.34 lb/gal is water density.

1 MGD = 694.4 gpm = 1.547 cfs; 1 cfs = 448.8 gpm; 1 acre-ft = 325,851 gal = 43,560 ft3.

Detention time = volume / flow; cubic feet over cfs yields seconds, gallons over MGD yields days.

Run a proportional magnitude check: doubling concentration at fixed flow must double load.

Last updated: June 2026

Start with the basis, not the formula

WRE calculation questions look different but share one unit engine. A wastewater load , a chlorine dose , a tank volume , a detention time , and a pollutant allocation all require the same first decision: what is being measured? The answer is a flow rate , concentration , mass rate , volume , surface loading rate , or time . Identify the basis before opening the NCEES PE Civil Reference Handbook (the April 2024 edition supplied on-screen) and the formula becomes obvious. The exam gives roughly 6 minutes per item across 80 questions in a 9-hour appointment, so a disciplined setup buys time.

The conversion constants you must memorize

  • From To Multiply by
  • 1 MGD gpm 694.4
  • 1 MGD cfs 1.547
  • 1 cfs gpm 448.8
  • 1 cfs MGD 0.6463
  • 1 acre-ft gallons 325,851
  • 1 ft3 gallons 7.481
  • Water density lb/gal 8.34
  • The master load equation

The single most-used WRE relationship is mass load = flow x concentration x conversion . In US units:

lb/day = Q (MGD) x C (mg/L) x 8.34

The 8.34 collapses (mg/L)(MG/day)(8.34 lb/gal per mg/L-MG). Worked example: a plant treats 2.5 MGD at 30 mg/L BOD5 . Load = 2.5 x 30 x 8.34 = 625.5 lb/day of BOD. If the question instead gives a permit load of 625 lb/day at 2.5 MGD and asks for concentration, rearrange: C = 625 / (2.5 x 8.34) = 30 mg/L. Never start by guessing a treatment formula.

  • Detention, storage, and loading logic
  • Detention time

Detention time t = V / Q, but V and Q often arrive on different time bases. A basin of 0.5 MG at 2.5 MGD gives t = 0.5/2.5 = 0.2 day = 4.8 hr . A channel of 1,800 ft3 at 6 cfs gives 1,800/6 = 300 s = 5 min directly, because ft3 over ft3/s is seconds. A stormwater pond of 5 acre-ft (217,800 ft3) at an inflow of 10 cfs gives 21,780 s = 6.05 hr only after converting acre-ft to ft3.

Surface and hydraulic loading

Surface overflow rate (SOR) = Q / plan area (gpd/ft2), used for clarifiers. Hydraulic loading rate = Q / filter area (gpm/ft2), used for filters. The units reveal the concept; a classic distractor substitutes tank volume for plan area . Example: 2.0 MGD over a 40-ft-diameter clarifier (area = pi/4 x 40^2 = 1,257 ft2) gives SOR = 2,000,000/1,257 = 1,591 gpd/ft2 , which sits above the typical 600-1,200 gpd/ft2 design range for secondary clarifiers and therefore flags this unit as hydraulically overloaded -- the reasonableness check is the real teaching point.

Workbook checks (run every problem)

State whether the answer should rise or fall as flow rises.

Keep concentration and load separate until the final line.

Convert time once; never switch day to hour mid-equation.

Ask whether the magnitude fits a pipe, plant, or watershed scale.

Re-read the requested unit before selecting an answer.

The four-row load drill

Run this until automatic. Row 1: convert plant flow to the day basis. Row 2: write concentration as mass per volume. Row 3: multiply with the 8.34 constant. Row 4: compare to the requested unit and expected direction. If concentration doubles at fixed flow, load doubles. If flow is halved at fixed concentration, load halves. This proportional check kills wrong choices before detailed arithmetic finishes, and it is the single highest-yield habit for the flow-and-load cluster of the WRE blueprint.

Population, per-capita, and SI cross-checks

Domestic loading often arrives per capita. A useful anchor: typical raw domestic wastewater is roughly 0.17-0.20 lb BOD per capita-day and design flow near 100 gpd per capita . A 50,000-person service area at 100 gpd/capita gives 5.0 MGD; at 0.20 lb BOD/capita-day the influent BOD load is 10,000 lb/day, which back-checks to a concentration of 10,000/(5.0 x 8.34) approximately 240 mg/L -- consistent with medium-strength domestic wastewater. When a problem mixes SI and US units, convert early: 1 mg/L = 1 g/m3 , 1 m3/s = 22.8 MGD, and load in kg/day = Q (m3/s) x C (mg/L) x 86.4.

Carrying these anchors lets you reject a choice that is off by an order of magnitude before you finish the arithmetic, which is exactly where the WRE flow-and-load distractors live.

Worked mass-balance example

Mass balance is the unifying tool: in = out + accumulation, and at steady state accumulation is zero. Consider a stream at 8 cfs carrying 4 mg/L of a conservative pollutant that receives a discharge of 1.5 cfs at 60 mg/L. The mixed concentration is the flow-weighted average: C = (8 x 4 + 1.5 x 60) / (8 + 1.5) = (32 + 90) / 9.5 = 12.8 mg/L . Notice the answer must fall between 4 and 60 mg/L and lean toward the larger flow's value -- a sanity check that immediately eliminates any choice outside that band or above 60.

The same flow-weighted blending governs reservoir mixing, recycle streams, and split-flow treatment, so practicing it as a standalone setup pays off across the entire water-quality and treatment portion of the blueprint.