Study guide
19.2 Hydraulics Energy and Head Workbook
NCEES PE Civil: Water Resources and Environmental Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: NCEES WRE Exam Spec and Reference Strategy
1.1 NCEES WRE Format 1.2 Reference Handbook and Units 1.3 Blueprint Prioritization
2 Chapter 6: WRE Project Planning, Cost, and Engineering Economics
6.1 Quantity Takeoff and Unit Basis 6.2 Cost Estimating and Bid Item Logic 6.3 Schedules, Sequencing, and Critical Path 6.4 Present Worth, Life-Cycle Cost, and Sustainability
3 Chapter 7: Soil Mechanics for WRE Problems
7.1 Lateral Earth Pressure and Retaining Situations 7.2 Consolidation, Compaction, and Settlement 7.3 Bearing Capacity and Slope Stability 7.4 Soil Data, Boring Logs, and Unit Conversions
4 Chapter 8: WRE Analysis and Hydraulic Design Foundations
8.1 Mass Balance and Hydraulic Loading 8.2 Solids Loading and Sludge Mass Balance 8.3 Hydraulic Flow Measurement and Instrumentation 8.4 Design Checks, Safety Factors, and Reasonableness
5 Chapter 9: WRE Hydrology, Runoff, and Storage Routing
9.1 Design Storms, IDF, and Time of Concentration 9.2 Rational Method and Peak Flow Limits 9.3 NRCS Curve Number and Unit Hydrographs 9.4 Detention, Retention, and Routing Checks
6 Chapter 10: Closed Conduit and Open Channel Hydraulics
10.1 Continuity, Energy, and HGL/EGL 10.2 Pipe Flow Losses, Pumps, and Net Head 10.3 Manning, Open Channel, and Critical Flow 10.4 Culverts, Weirs, Orifices, and Control Sections
7 Chapter 11: Groundwater, Wells, and Aquifer Flow
11.1 Darcy Law, Gradient, and Flow Area 11.2 Confined and Unconfined Aquifers and Storage 11.3 Well Drawdown, Specific Capacity, and Interference 11.4 Contaminant Transport and Dewatering Decisions
8 Chapter 12: Water Quality Chemistry and Pollutant Loading
12.1 Concentration, Load, and Mass-Rate Conversions 12.2 BOD, CBOD, DO, and Oxygen Demand 12.3 Nutrients, pH, Alkalinity, and Buffering 12.4 Pollutant Allocation, TMDL, and Water Quality Criteria
9 Chapter 13: Water Treatment Processes and Design Checks
13.1 Coagulation, Flocculation, and Sedimentation 13.2 Filtration, Disinfection, and CT Logic 13.3 Softening, Iron, Manganese, and Chemical Feed 13.4 Treatment Plant Hydraulics and Operations
10 Chapter 14: Wastewater Collection, Treatment, and Sludge
14.1 Collection-System Hydraulics and Infiltration 14.2 Preliminary, Primary, and Secondary Treatment 14.3 Nutrient Removal and Effluent Quality 14.4 Sludge Processing, Digestion, and Dewatering
11 Chapter 3: Water Quality, Treatment, and Sitework
Water Quality and Regulation Drinking Water and Wastewater Treatment Project Sitework and Final Review
12 Chapter 15: Sitework, Drainage, and Erosion Control
15.1 Grading, Cut/Fill, and Earthwork Balancing 15.2 Storm Drain Inlets and Minor Systems 15.3 Erosion, Sediment Control, and BMPs 15.4 Permitting, Constructability, and Field Adjustments
13 Chapter 4: Materials, Analysis, and Design for WRE
4.1 Materials and Pipe Selection 4.2 Analysis and Design Workflow 4.3 Site-Civil Constructability
14 Chapter 16: Materials, Pipes, Standards, and Reference Navigation
16.1 Pipe Material Selection and Failure Modes 16.2 Concrete, Soil, and Geosynthetic Materials 16.3 Design Standard Navigation and Revision Years 16.4 Reference Search Drills and Unit Checks
15 Chapter 18: Pumps, Distribution, and Collection Systems
18.1 Pump Curves, System Curves, and Operating Point 18.2 Water Distribution Pressure, Demand, and Storage 18.3 Sewer Collection, Lift Stations, and Force Mains 18.4 Transient, Surge, and Operational Troubleshooting
16 Chapter 19: WRE Calculation Workbook and Unit Drills
19.1 Flow, Concentration, and Load Workbook 19.2 Hydraulics Energy and Head Workbook 19.3 Treatment and Process Sizing Workbook 19.4 Error Patterns and Repair Drills
17 Chapter 5: Mixed Practice, Units, and Final Review
Formula Selection and Units Mixed WRE Mock Review Exam Day and Spec Transition
18 Chapter 17: Full-Length WRE Mixed Practice and Final Review
17.1 Eighty-Question Mock Exam Plan 17.2 Miss-Log Diagnostics by Domain 17.3 Calculator, Reference, and Break Strategy 17.4 Final-Week Current vs 2027 Spec Check
19.2 Hydraulics Energy and Head Workbook
Key Takeaways Explain This Topic AI
Write the Bernoulli energy equation with two labeled stations before substituting any number.
Velocity head V2/2g uses g = 32.2 ft/s2; the hydraulic grade line excludes it, the energy grade line includes it.
Hazen-Williams hf = 10.44 L Q^1.85 / (C^1.85 d^4.87) (US units) is the WRE pressure-pipe default; Darcy-Weisbach when f is given.
Manning Q = (1.49/n) A R^(2/3) S^(1/2) governs open-channel normal depth in US units.
Pump head is added energy; friction, minor losses, and turbines subtract it.
Last updated: June 2026
Build the energy line before calculating
Every hydraulics problem is the energy (Bernoulli) equation between two stations:
z1 + p1/gamma + V1^2/2g + hp = z2 + p2/gamma + V2^2/2g + hL
where z is elevation head, p/gamma is pressure head, V^2/2g is velocity head (with g = 32.2 ft/s2 ), hp is pump head added, and hL is total head loss. In open-channel flow the same energy idea applies but the free surface, channel slope, and critical-depth control change the setup. The PE WRE exam rewards candidates who recognize the control rather than memorize isolated equations.
Head term checklist
- Term Formula / meaning Common mistake
- Elevation head z above datum Mixing pipe invert and water surface
- Pressure head p / gamma (gamma = 62.4 lb/ft3) Gauge versus absolute confusion
- Velocity head V^2 / 2g Dropping it where diameter changes
- Friction loss Hazen-Williams or Darcy Wrong reach length or roughness
- Minor loss K V^2/2g Ignoring a large valve or entrance
- Pump head hp added to flow Confusing pump power with pump head
Label station 1 upstream and station 2 downstream, then decide what is known at each. Equal diameters at steady flow let velocity head cancel. A reservoir surface station has negligible velocity (treat V approximately 0). A nozzle or free outfall station has velocity as the central term.
HGL, EGL, and the headloss models
The hydraulic grade line (HGL) is z + p/gamma. The energy grade line (EGL) adds V^2/2g, so EGL always plots above HGL by the velocity head. In a constant-diameter pipe the two lines run parallel; at a pump both jump up; through losses both fall. In open channels the water surface is the HGL, but jumps and transitions need care.
Pressure-pipe headloss
The WRE default is Hazen-Williams (US units): hf = 10.44 L Q^1.85 / (C^1.85 d^4.87), with L and d in ft, Q in gpm, and C the roughness coefficient (C approximately 130-140 for new cast/ductile iron, 150 for PVC). Use Darcy-Weisbach hf = f (L/d)(V^2/2g) only when the friction factor f or a Moody-chart path is given.
Worked example: 1,000 ft of 12-in (d=1.0 ft) ductile iron, C=130, Q=1,400 gpm. hf = 10.44(1000)(1400^1.85)/(130^1.85 x 1.0^4.87). With 1400^1.85 approximately 815,000 and 130^1.85 approximately 7,600, hf approximately 11.2 ft . A magnitude check: a few feet to low tens of feet per 1,000 ft is reasonable for a transmission main.
Open-channel workflow
First classify: normal depth, critical depth, gradually varied flow, hydraulic jump, culvert, weir, or orifice. Manning Q = (1.49/n) A R^(2/3) S^(1/2) handles uniform normal flow, with R = A/P (hydraulic radius) and n approximately 0.013 for concrete, 0.024 for natural channels. Critical depth occurs where specific energy is minimum (Froude number = 1).
Pump power and the brake-horsepower trap
A frequent WRE distractor confuses pump head with pump power . Once you have total dynamic head (TDH), water horsepower is:
WHP = Q (gpm) x TDH (ft) / 3,960
and brake horsepower divides by efficiency: BHP = WHP / eta . Example: 1,400 gpm against a TDH of 120 ft gives WHP = 1,400 x 120 / 3,960 = 42.4 hp ; at a wire-to-water efficiency of 0.70, BHP = 42.4/0.70 = 60.6 hp . The 3,960 constant collapses 8.34 lb/gal, 60 min/hr, and 33,000 ft-lb/min per hp. If the question asks for the motor size, the answer is BHP (or the next standard motor up), never WHP -- a classic four-choice trap that lists both.
Mini energy-sketch drill
For every practice problem make a ten-second sketch: upstream station, downstream station, datum, pressure condition, velocity change, pump or control, and the major loss reach. If no energy is added, total energy cannot rise downstream. If the sketch shows a profile climbing through a loss, reject it. This habit is decisive when answer choices mix pressure, head, power, and elevation values that all look numerically plausible.
Reasonableness anchors
Keep target ranges in mind to filter answers. Gravity sewer velocities should be roughly 2-10 ft/s (about 2 ft/s minimum for self-cleansing, 10 ft/s upper bound to limit scour). Force-main and water-main velocities typically run 3-8 ft/s . A negative pressure where the line should stay pressurized signals an error or a real cavitation/air-entrainment concern. A computed Froude number above 1 means supercritical flow (steep, fast, shallow); below 1 means subcritical (mild, deep, slow), and a hydraulic jump transitions from supercritical to subcritical with energy loss.
When a velocity, pressure, or depth lands far outside these bands, re-check the unit basis and the chosen control before committing to an answer choice.
Weirs, orifices, and minor losses
Control structures have their own forms. A rectangular sharp-crested weir follows Q = C L H^(3/2) (with C approximately 3.33 in US units, L crest length, H head over the crest); a V-notch (90-degree) weir follows Q = 2.5 H^(2.5) . An orifice follows Q = Cd A sqrt(2gH) with Cd approximately 0.6. Minor losses sum as hL = (sum of K) V^2/2g, with K approximately 0.5 for a sharp entrance, 1.0 for a sudden exit, and roughly 10 for a fully open gate-to-globe range of valves.
When a transmission problem gives both pipe friction and several fittings, add friction and minor losses before applying the energy equation -- omitting a large valve K is a frequent off-by-a-few-feet error that still changes which discrete answer choice is correct.