Study guide

11.3 Well Drawdown, Specific Capacity, and Interference

NCEES PE Civil: Water Resources and Environmental Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: NCEES WRE Exam Spec and Reference Strategy

1.1 NCEES WRE Format 1.2 Reference Handbook and Units 1.3 Blueprint Prioritization

2 Chapter 6: WRE Project Planning, Cost, and Engineering Economics

6.1 Quantity Takeoff and Unit Basis 6.2 Cost Estimating and Bid Item Logic 6.3 Schedules, Sequencing, and Critical Path 6.4 Present Worth, Life-Cycle Cost, and Sustainability

3 Chapter 7: Soil Mechanics for WRE Problems

7.1 Lateral Earth Pressure and Retaining Situations 7.2 Consolidation, Compaction, and Settlement 7.3 Bearing Capacity and Slope Stability 7.4 Soil Data, Boring Logs, and Unit Conversions

4 Chapter 8: WRE Analysis and Hydraulic Design Foundations

8.1 Mass Balance and Hydraulic Loading 8.2 Solids Loading and Sludge Mass Balance 8.3 Hydraulic Flow Measurement and Instrumentation 8.4 Design Checks, Safety Factors, and Reasonableness

5 Chapter 9: WRE Hydrology, Runoff, and Storage Routing

9.1 Design Storms, IDF, and Time of Concentration 9.2 Rational Method and Peak Flow Limits 9.3 NRCS Curve Number and Unit Hydrographs 9.4 Detention, Retention, and Routing Checks

6 Chapter 10: Closed Conduit and Open Channel Hydraulics

10.1 Continuity, Energy, and HGL/EGL 10.2 Pipe Flow Losses, Pumps, and Net Head 10.3 Manning, Open Channel, and Critical Flow 10.4 Culverts, Weirs, Orifices, and Control Sections

7 Chapter 11: Groundwater, Wells, and Aquifer Flow

11.1 Darcy Law, Gradient, and Flow Area 11.2 Confined and Unconfined Aquifers and Storage 11.3 Well Drawdown, Specific Capacity, and Interference 11.4 Contaminant Transport and Dewatering Decisions

8 Chapter 12: Water Quality Chemistry and Pollutant Loading

12.1 Concentration, Load, and Mass-Rate Conversions 12.2 BOD, CBOD, DO, and Oxygen Demand 12.3 Nutrients, pH, Alkalinity, and Buffering 12.4 Pollutant Allocation, TMDL, and Water Quality Criteria

9 Chapter 13: Water Treatment Processes and Design Checks

13.1 Coagulation, Flocculation, and Sedimentation 13.2 Filtration, Disinfection, and CT Logic 13.3 Softening, Iron, Manganese, and Chemical Feed 13.4 Treatment Plant Hydraulics and Operations

10 Chapter 14: Wastewater Collection, Treatment, and Sludge

14.1 Collection-System Hydraulics and Infiltration 14.2 Preliminary, Primary, and Secondary Treatment 14.3 Nutrient Removal and Effluent Quality 14.4 Sludge Processing, Digestion, and Dewatering

11 Chapter 3: Water Quality, Treatment, and Sitework

Water Quality and Regulation Drinking Water and Wastewater Treatment Project Sitework and Final Review

12 Chapter 15: Sitework, Drainage, and Erosion Control

15.1 Grading, Cut/Fill, and Earthwork Balancing 15.2 Storm Drain Inlets and Minor Systems 15.3 Erosion, Sediment Control, and BMPs 15.4 Permitting, Constructability, and Field Adjustments

13 Chapter 4: Materials, Analysis, and Design for WRE

4.1 Materials and Pipe Selection 4.2 Analysis and Design Workflow 4.3 Site-Civil Constructability

14 Chapter 16: Materials, Pipes, Standards, and Reference Navigation

16.1 Pipe Material Selection and Failure Modes 16.2 Concrete, Soil, and Geosynthetic Materials 16.3 Design Standard Navigation and Revision Years 16.4 Reference Search Drills and Unit Checks

15 Chapter 18: Pumps, Distribution, and Collection Systems

18.1 Pump Curves, System Curves, and Operating Point 18.2 Water Distribution Pressure, Demand, and Storage 18.3 Sewer Collection, Lift Stations, and Force Mains 18.4 Transient, Surge, and Operational Troubleshooting

16 Chapter 19: WRE Calculation Workbook and Unit Drills

19.1 Flow, Concentration, and Load Workbook 19.2 Hydraulics Energy and Head Workbook 19.3 Treatment and Process Sizing Workbook 19.4 Error Patterns and Repair Drills

17 Chapter 5: Mixed Practice, Units, and Final Review

Formula Selection and Units Mixed WRE Mock Review Exam Day and Spec Transition

18 Chapter 17: Full-Length WRE Mixed Practice and Final Review

17.1 Eighty-Question Mock Exam Plan 17.2 Miss-Log Diagnostics by Domain 17.3 Calculator, Reference, and Break Strategy 17.4 Final-Week Current vs 2027 Spec Check

11.3 Well Drawdown, Specific Capacity, and Interference

Key Takeaways Explain This Topic AI

Drawdown is the nonpumping water level minus the pumping water level at a well or observation point.

Specific capacity is Q / s, usually in gpm per ft of drawdown, and is a practical field indicator of well performance, not a fixed aquifer constant.

Confined steady radial-flow equations use transmissivity and a logarithmic radius term because the cylindrical flow area expands away from the well.

Interference occurs when drawdown cones from nearby wells overlap; in linear confined-aquifer problems drawdowns superimpose by simple addition.

A falling specific capacity during a constant-rate test can signal well loss, screen clogging, boundary effects, aquifer dewatering, or delayed drainage.

Last updated: June 2026

Drawdown and Well Performance

The April 2024 PE Civil WRE specification explicitly lists well and drawdown analysis. Items may demand a direct calculation or may ask what a pump-test result means for supply, dewatering, or site impacts. Begin every well problem by separating water levels, pumping rate, aquifer response, and well efficiency.

Core Terms

Static water level is the level before pumping or after full recovery. Pumping water level is the level during pumping. Drawdown s is static level minus pumping level at the same point. In a pumped well, measured drawdown includes aquifer drawdown plus extra head loss near and inside the well (well loss). In an observation well, drawdown better represents the true aquifer response because it excludes screen-entrance and wellbore losses.

Specific capacity is Q / s, often in gpm/ft. A larger value means more yield per foot of drawdown. It is not a fixed aquifer constant because it changes with pumping duration, rate, well condition, turbulent well loss, boundaries, and seasonal recharge. Theis-based theory shows specific capacity declines slowly with time as the cone of depression expands.

  • Item Formula or meaning Exam use
  • Drawdown s = static level - pumping level Basic water-level calculation
  • Specific capacity Q / s Quick well-performance comparison
  • Transmissivity T = K b Confined radial-flow analysis
  • Radius of influence R Outer limit of the drawdown cone
  • Interference Sum of overlapping drawdowns Multiwell and field operations
  • Radial Flow Equations

For steady confined radial flow to a fully penetrating well, the Thiem equation in flow form is Q = 2 pi T (h2 - h1) / ln(r2 / r1). The drawdown form is s = Q ln(R / r) / (2 pi T). Both reflect a cylindrical flow area that grows with radius. Do not substitute a rectangular Darcy area for a well unless the problem deliberately simplifies the geometry.

For an unconfined aquifer under Dupuit assumptions, steady radial flow is Q = pi K (h2^2 - h1^2) / ln(r2 / r1), where h1 and h2 are saturated thicknesses above the base. When drawdown is large relative to saturated thickness, a confined approximation can misstate the result; a corrected drawdown s' = s - s^2/(2b) is sometimes applied to convert observed unconfined drawdown to an equivalent confined value.

Pump-Test Workflow

Record static level, pumping rate, pumping level, time, and observation-well distances.

Compute drawdown at each measured point.

Compute specific capacity if well performance is requested.

Estimate transmissivity from observation-well data, since pumped-well data carry extra well losses.

Confirm assumptions match the formula: confined or unconfined, steady or transient, full or partial penetration, constant rate, valid boundaries.

Read late-time trends for recharge boundaries (flattening), impermeable boundaries (steepening), delayed yield, or nearby pumping.

Interference

When two wells pump near each other, their cones of depression overlap. In linear confined-aquifer problems the aquifer response is treated as linear, so drawdowns from separate wells add at a point by superposition. This supports wellfield spacing, dewatering layout, and judging whether a new production well will harm an existing one.

Interference is not always harmful. A dewatering system uses intentional interference among wellpoints or deep wells to depress groundwater across an excavation. For supply wells, excessive interference reduces available drawdown, raises pumping cost, and can trigger impacts at property lines or wetlands.

Well Loss and Step-Drawdown Tests

Total drawdown in a pumped well is often modeled as s = B Q + C Q^2, where B Q is the laminar aquifer (formation) loss that scales linearly with rate and C Q^2 is the turbulent well loss from flow through the screen and casing. Well efficiency is the ratio B Q / (B Q + C Q^2). A step-drawdown test runs the well at several increasing rates to separate B from C; a large C signals a clogged or undersized screen and a candidate for rehabilitation. Because specific capacity is Q / s = 1 / (B + C Q), it falls as Q rises even when the aquifer is unchanged, which is why specific capacity must always be quoted with its test rate.

Worked Example

A confined aquifer has T = 3,000 ft^2/day. A fully penetrating well pumps so that drawdown is 3.0 ft at r = 50 ft and 1.2 ft at r = 400 ft. Using the Thiem drawdown difference, s1 - s2 = Q ln(r2 / r1) / (2 pi T), so 3.0 - 1.2 = Q ln(400/50) / (2 pi x 3,000). Then 1.8 = Q (2.079) / 18,850, giving Q = 1.8 x 18,850 / 2.079 = 16,320 ft^3/day, about 85 gpm. Note the larger drawdown is at the smaller radius, closer to the well.

Practical Traps

Specific capacity is Q divided by drawdown, never drawdown divided by Q; a deeper pumping level means a larger drawdown and a smaller specific capacity.

Pumping and static levels given as elevations must be differenced as elevations, not as depths below grade.

Radial-flow equations use natural log unless the supplied formula uses log base 10 with the 2.303 factor folded in.

Use observation-well drawdown, not pumped-well drawdown, to estimate transmissivity, because the pumped well carries the C Q^2 well loss. Mixing these is a frequent distractor.