Study guide

16.2 Concrete, Soil, and Geosynthetic Materials

NCEES PE Civil: Water Resources and Environmental Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: NCEES WRE Exam Spec and Reference Strategy

1.1 NCEES WRE Format 1.2 Reference Handbook and Units 1.3 Blueprint Prioritization

2 Chapter 6: WRE Project Planning, Cost, and Engineering Economics

6.1 Quantity Takeoff and Unit Basis 6.2 Cost Estimating and Bid Item Logic 6.3 Schedules, Sequencing, and Critical Path 6.4 Present Worth, Life-Cycle Cost, and Sustainability

3 Chapter 7: Soil Mechanics for WRE Problems

7.1 Lateral Earth Pressure and Retaining Situations 7.2 Consolidation, Compaction, and Settlement 7.3 Bearing Capacity and Slope Stability 7.4 Soil Data, Boring Logs, and Unit Conversions

4 Chapter 8: WRE Analysis and Hydraulic Design Foundations

8.1 Mass Balance and Hydraulic Loading 8.2 Solids Loading and Sludge Mass Balance 8.3 Hydraulic Flow Measurement and Instrumentation 8.4 Design Checks, Safety Factors, and Reasonableness

5 Chapter 9: WRE Hydrology, Runoff, and Storage Routing

9.1 Design Storms, IDF, and Time of Concentration 9.2 Rational Method and Peak Flow Limits 9.3 NRCS Curve Number and Unit Hydrographs 9.4 Detention, Retention, and Routing Checks

6 Chapter 10: Closed Conduit and Open Channel Hydraulics

10.1 Continuity, Energy, and HGL/EGL 10.2 Pipe Flow Losses, Pumps, and Net Head 10.3 Manning, Open Channel, and Critical Flow 10.4 Culverts, Weirs, Orifices, and Control Sections

7 Chapter 11: Groundwater, Wells, and Aquifer Flow

11.1 Darcy Law, Gradient, and Flow Area 11.2 Confined and Unconfined Aquifers and Storage 11.3 Well Drawdown, Specific Capacity, and Interference 11.4 Contaminant Transport and Dewatering Decisions

8 Chapter 12: Water Quality Chemistry and Pollutant Loading

12.1 Concentration, Load, and Mass-Rate Conversions 12.2 BOD, CBOD, DO, and Oxygen Demand 12.3 Nutrients, pH, Alkalinity, and Buffering 12.4 Pollutant Allocation, TMDL, and Water Quality Criteria

9 Chapter 13: Water Treatment Processes and Design Checks

13.1 Coagulation, Flocculation, and Sedimentation 13.2 Filtration, Disinfection, and CT Logic 13.3 Softening, Iron, Manganese, and Chemical Feed 13.4 Treatment Plant Hydraulics and Operations

10 Chapter 14: Wastewater Collection, Treatment, and Sludge

14.1 Collection-System Hydraulics and Infiltration 14.2 Preliminary, Primary, and Secondary Treatment 14.3 Nutrient Removal and Effluent Quality 14.4 Sludge Processing, Digestion, and Dewatering

11 Chapter 3: Water Quality, Treatment, and Sitework

Water Quality and Regulation Drinking Water and Wastewater Treatment Project Sitework and Final Review

12 Chapter 15: Sitework, Drainage, and Erosion Control

15.1 Grading, Cut/Fill, and Earthwork Balancing 15.2 Storm Drain Inlets and Minor Systems 15.3 Erosion, Sediment Control, and BMPs 15.4 Permitting, Constructability, and Field Adjustments

13 Chapter 4: Materials, Analysis, and Design for WRE

4.1 Materials and Pipe Selection 4.2 Analysis and Design Workflow 4.3 Site-Civil Constructability

14 Chapter 16: Materials, Pipes, Standards, and Reference Navigation

16.1 Pipe Material Selection and Failure Modes 16.2 Concrete, Soil, and Geosynthetic Materials 16.3 Design Standard Navigation and Revision Years 16.4 Reference Search Drills and Unit Checks

15 Chapter 18: Pumps, Distribution, and Collection Systems

18.1 Pump Curves, System Curves, and Operating Point 18.2 Water Distribution Pressure, Demand, and Storage 18.3 Sewer Collection, Lift Stations, and Force Mains 18.4 Transient, Surge, and Operational Troubleshooting

16 Chapter 19: WRE Calculation Workbook and Unit Drills

19.1 Flow, Concentration, and Load Workbook 19.2 Hydraulics Energy and Head Workbook 19.3 Treatment and Process Sizing Workbook 19.4 Error Patterns and Repair Drills

17 Chapter 5: Mixed Practice, Units, and Final Review

Formula Selection and Units Mixed WRE Mock Review Exam Day and Spec Transition

18 Chapter 17: Full-Length WRE Mixed Practice and Final Review

17.1 Eighty-Question Mock Exam Plan 17.2 Miss-Log Diagnostics by Domain 17.3 Calculator, Reference, and Break Strategy 17.4 Final-Week Current vs 2027 Spec Check

16.2 Concrete, Soil, and Geosynthetic Materials

Key Takeaways Explain This Topic AI

The April 2024 WRE Materials area explicitly includes soil classification, boring-log interpretation, soil properties, concrete, piping materials, test methods, and specification conformance.

Soil classification is not just a geotechnical topic on WRE; it drives trench stability, bedding, compaction, infiltration, liner selection, retaining walls, and erosion-control performance.

Concrete questions usually test durability, nonreinforced versus reinforced behavior, curing, water-cement (w/c) ratio logic, and suitability for water or wastewater exposure.

Geosynthetics appear through sitework functions — separation, filtration, drainage, reinforcement, erosion control, and containment — even when the word geosynthetic is absent from the prompt.

Material conformance answers come from comparing the measured property to the specified acceptance criterion, never from intuition about whether the material 'seems strong.'

Last updated: June 2026

Materials Beyond the Pipe Barrel

The WRE exam does not treat materials as a standalone memorization chapter. Materials explain why a trench sloughs, why a pond liner leaks, why a concrete tank spalls, why a filter clogs, and why a retaining-wall backfill drains or builds pressure. The April 2024 specification names soil classification, boring-log interpretation, soil properties, concrete, piping materials, and material test methods — all tied to sitework, hydrology, wastewater facilities, and construction conformance.

Soil Properties to Read From the Problem

Most soil items hand you enough data to classify behavior. Look for grain-size distribution, Atterberg limits, moisture content, dry density, groundwater elevation, standard penetration test (SPT) N-values, and notes such as fill, organics, loose sand, stiff clay, or refusal. Under the Unified Soil Classification System (USCS) , the dividing sieve between coarse and fine is the No. 200 (0.075 mm): coarse-grained soils retain more than 50 percent on it; fine-grained soils pass more than 50 percent through it.

Property or clue WRE consequence Typical exam use

High-plasticity clay (CH) Low permeability, shrink-swell risk, slow drainage Pond liner support, trench backfill, settlement

Clean sand or gravel (SP/GP) High permeability, low cohesion Dewatering, filter design, infiltration BMP, bedding

  • Organic or soft soil (OL/OH/Pt) Compressible and weak Embankment settlement, unstable cut, poor foundation
  • Dense granular fill Good drainage, compactable Pipe bedding, structural backfill, underdrain envelope
  • Groundwater above trench invert Buoyancy, instability, inflow Dewatering, bedding migration, pipe flotation

A frequent calculation is relative compaction :

Relative compaction = (field dry density / laboratory maximum dry density) x 100 percent.

If trench backfill has a field dry density of 112 pcf and the standard Proctor maximum dry density is 120 pcf, relative compaction = 112 / 120 x 100 = 93.3 percent. A 95-percent specification means the lift fails and must be recompacted, even if the pipe itself is acceptable.

Concrete in WRE Facilities

Concrete appears in channels, manholes, junction boxes, culverts, tank slabs, foundations, headwalls, spillways, and treatment basins. Distinguish nonreinforced concrete , which relies on compressive strength and mass, from reinforced concrete , which uses steel to resist tension and control cracking.

For durability, focus on exposure. Water and wastewater structures face wet-dry cycling, freeze-thaw, sulfate attack, low pH, hydrogen-sulfide corrosion of the crown, chloride exposure, and grit abrasion. Lower water-cement ratio (often w/c below about 0.45 for severe exposure), proper curing, adequate cover, air entrainment where freeze-thaw applies, and sulfate-resistant cement all improve durability. On the exam, a low compressive-strength break, excessive slump, missing curing, or wrong exposure class is a specification problem, not a hydraulic one.

Geosynthetics by Function

Geosynthetics earn their keep by delivering one defined function in a thin manufactured layer. Do not mix the functions:

Geotextile separation keeps subgrade fines from pumping into aggregate.

Geotextile filtration passes water while retaining soil at drains, swales, and outlet protection; specified by permittivity and apparent opening size (AOS).

Geocomposite drainage provides an in-plane flow path behind walls or below caps.

Geogrid reinforcement improves soil or aggregate mass stability; specified by tensile strength.

Geomembrane containment limits seepage from ponds, tanks, landfills, or contaminated areas.

Erosion-control blankets / turf reinforcement mats protect channels and slopes until vegetation establishes.

A geotextile under riprap at a channel outlet is a filter/separation layer. A geomembrane under a detention pond is a seepage barrier. A geogrid in retaining-wall backfill is reinforcement, not a filter. When the prompt gives permittivity, AOS, tensile strength, puncture resistance, or interface friction, match that property to the specified function.

Calculation and Conformance Workflow

Identify the required property: gradation, plasticity, density, strength, permeability, slump, air content, thickness, tensile strength, or opening size.

Convert units before comparing.

Compare the measured test result to the acceptance range.

Decide the consequence: accept, reject, retest, recompact, redesign, or add protection.

That workflow blocks a frequent PE mistake — answering from material preference instead of the acceptance criterion stated in the problem.

Reading a Boring Log Quickly

A boring log is a vertical record of what the drill found. Scan it top to bottom for four things the exam cares about. First, the groundwater table depth (and date measured), because it sets dewatering, buoyancy, and bedding-migration concerns. Second, the soil sequence — surface fill, then native strata — since a soft or organic layer beneath a foundation drives settlement. Third, SPT N-values , a rough strength and density index: N below about 4 in sand is very loose, N above about 30 is dense; in clay, low N means soft and compressible.

Fourth, refusal , which marks rock or a very dense layer and may control pile tip or excavation limits.

  • Boring-log clue Immediate WRE interpretation
  • Water table at 6 ft, trench invert at 10 ft Dewatering and flotation/buoyancy check required
  • 8 ft of fill over native clay Suspect uncontrolled fill; settlement and bearing risk
  • Organic silt (OL) layer at depth Long-term consolidation settlement of structures above
  • SPT N = 2 in sand Very loose; liquefaction/settlement concern, poor bearing
  • Refusal at 14 ft Rock or hardpan; affects excavation cost and pile design
  • Bedding Classes and Why They Matter

Buried-pipe load capacity is not a property of the pipe alone — it depends on the bedding . Rigid pipe (RCP) is rated by D-load (the three-edge-bearing test) multiplied by a bedding factor: better bedding (Class A concrete cradle, Class B shaped granular) supports more load than dumped backfill (Class D). Flexible pipe (PVC, HDPE) relies on the surrounding compacted soil to limit ring deflection; the Iowa formula links deflection to the modulus of soil reaction, so poor haunch compaction is the usual culprit when a flexible pipe deflects.

On the exam, a buried-pipe failure with adequate wall strength almost always points back to bedding or haunching, not the pipe material itself.