Study guide

15.3 Erosion, Sediment Control, and BMPs

NCEES PE Civil: Water Resources and Environmental Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: NCEES WRE Exam Spec and Reference Strategy

1.1 NCEES WRE Format 1.2 Reference Handbook and Units 1.3 Blueprint Prioritization

2 Chapter 6: WRE Project Planning, Cost, and Engineering Economics

6.1 Quantity Takeoff and Unit Basis 6.2 Cost Estimating and Bid Item Logic 6.3 Schedules, Sequencing, and Critical Path 6.4 Present Worth, Life-Cycle Cost, and Sustainability

3 Chapter 7: Soil Mechanics for WRE Problems

7.1 Lateral Earth Pressure and Retaining Situations 7.2 Consolidation, Compaction, and Settlement 7.3 Bearing Capacity and Slope Stability 7.4 Soil Data, Boring Logs, and Unit Conversions

4 Chapter 8: WRE Analysis and Hydraulic Design Foundations

8.1 Mass Balance and Hydraulic Loading 8.2 Solids Loading and Sludge Mass Balance 8.3 Hydraulic Flow Measurement and Instrumentation 8.4 Design Checks, Safety Factors, and Reasonableness

5 Chapter 9: WRE Hydrology, Runoff, and Storage Routing

9.1 Design Storms, IDF, and Time of Concentration 9.2 Rational Method and Peak Flow Limits 9.3 NRCS Curve Number and Unit Hydrographs 9.4 Detention, Retention, and Routing Checks

6 Chapter 10: Closed Conduit and Open Channel Hydraulics

10.1 Continuity, Energy, and HGL/EGL 10.2 Pipe Flow Losses, Pumps, and Net Head 10.3 Manning, Open Channel, and Critical Flow 10.4 Culverts, Weirs, Orifices, and Control Sections

7 Chapter 11: Groundwater, Wells, and Aquifer Flow

11.1 Darcy Law, Gradient, and Flow Area 11.2 Confined and Unconfined Aquifers and Storage 11.3 Well Drawdown, Specific Capacity, and Interference 11.4 Contaminant Transport and Dewatering Decisions

8 Chapter 12: Water Quality Chemistry and Pollutant Loading

12.1 Concentration, Load, and Mass-Rate Conversions 12.2 BOD, CBOD, DO, and Oxygen Demand 12.3 Nutrients, pH, Alkalinity, and Buffering 12.4 Pollutant Allocation, TMDL, and Water Quality Criteria

9 Chapter 13: Water Treatment Processes and Design Checks

13.1 Coagulation, Flocculation, and Sedimentation 13.2 Filtration, Disinfection, and CT Logic 13.3 Softening, Iron, Manganese, and Chemical Feed 13.4 Treatment Plant Hydraulics and Operations

10 Chapter 14: Wastewater Collection, Treatment, and Sludge

14.1 Collection-System Hydraulics and Infiltration 14.2 Preliminary, Primary, and Secondary Treatment 14.3 Nutrient Removal and Effluent Quality 14.4 Sludge Processing, Digestion, and Dewatering

11 Chapter 3: Water Quality, Treatment, and Sitework

Water Quality and Regulation Drinking Water and Wastewater Treatment Project Sitework and Final Review

12 Chapter 15: Sitework, Drainage, and Erosion Control

15.1 Grading, Cut/Fill, and Earthwork Balancing 15.2 Storm Drain Inlets and Minor Systems 15.3 Erosion, Sediment Control, and BMPs 15.4 Permitting, Constructability, and Field Adjustments

13 Chapter 4: Materials, Analysis, and Design for WRE

4.1 Materials and Pipe Selection 4.2 Analysis and Design Workflow 4.3 Site-Civil Constructability

14 Chapter 16: Materials, Pipes, Standards, and Reference Navigation

16.1 Pipe Material Selection and Failure Modes 16.2 Concrete, Soil, and Geosynthetic Materials 16.3 Design Standard Navigation and Revision Years 16.4 Reference Search Drills and Unit Checks

15 Chapter 18: Pumps, Distribution, and Collection Systems

18.1 Pump Curves, System Curves, and Operating Point 18.2 Water Distribution Pressure, Demand, and Storage 18.3 Sewer Collection, Lift Stations, and Force Mains 18.4 Transient, Surge, and Operational Troubleshooting

16 Chapter 19: WRE Calculation Workbook and Unit Drills

19.1 Flow, Concentration, and Load Workbook 19.2 Hydraulics Energy and Head Workbook 19.3 Treatment and Process Sizing Workbook 19.4 Error Patterns and Repair Drills

17 Chapter 5: Mixed Practice, Units, and Final Review

Formula Selection and Units Mixed WRE Mock Review Exam Day and Spec Transition

18 Chapter 17: Full-Length WRE Mixed Practice and Final Review

17.1 Eighty-Question Mock Exam Plan 17.2 Miss-Log Diagnostics by Domain 17.3 Calculator, Reference, and Break Strategy 17.4 Final-Week Current vs 2027 Spec Check

15.3 Erosion, Sediment Control, and BMPs

Key Takeaways Explain This Topic AI

Erosion control prevents soil detachment, while sediment control traps particles after they have been mobilized; good plans use both.

Construction stormwater permitting under NPDES applies when land disturbance is one acre or more, or less than one acre within a larger common plan of development or sale that ultimately disturbs one acre or more.

Best management practices must match the flow condition: silt fence is for shallow sheet flow, not high-velocity concentrated flow.

Temporary BMPs protect the active construction phase, while permanent BMPs such as swales, infiltration areas, outlet protection, and detention features support final site performance.

Inspection and maintenance are part of the design concept because clogged inlet protection, undermined silt fence, or full sediment basins no longer provide their assumed function.

Last updated: June 2026

Erosion Control Is Not the Same as Sediment Control

Erosion control keeps soil from being detached and transported in the first place. Sediment control captures soil after it has already moved. PE Civil WRE questions frequently hinge on that distinction. If a slope is bare and steep, the best first move is stabilization or upslope flow diversion, not simply adding a downstream fence and hoping it catches everything. The governing principle is the erosion control hierarchy : prevent, then divert, then capture.

The physics behind prevention is captured by the Universal Soil Loss Equation (USLE) , A = R x K x LS x C x P, where A is average annual soil loss (tons/acre/year), R is rainfall erosivity, K is soil erodibility, LS is the slope length-steepness factor, C is the cover-management factor, and P is the support-practice factor. The two factors an engineer most directly controls during construction are C (mulch, blankets, seeding cut C from near 1.0 on bare soil to below 0.1) and LS (shorter, flatter slopes through phasing and diversion benches).

This is why stabilizing cover and breaking up slope length beat chasing sediment downstream.

Permitting Context

Under the federal National Pollutant Discharge Elimination System (NPDES) program, construction stormwater permit coverage is generally required for sites disturbing one or more acres , and for smaller disturbances that are part of a common plan of development or sale that will ultimately disturb one or more acres. Many states are delegated to administer the program through their own Construction General Permit and may add stricter requirements. Coverage requires preparing and following a Stormwater Pollution Prevention Plan (SWPPP) .

For PE purposes, remember that clearing, grading, excavation, stockpiles, dewatering, concrete washout, fueling, and material storage can all generate stormwater pollutants beyond sediment.

BMP Selection Table

  • BMP Primary purpose Best use Common misuse
  • Construction phasing Reduce exposed soil area Large staged sites Disturbing the full site too early
  • Temporary seeding or mulch Prevent erosion Inactive disturbed areas Waiting until final grading only

Diversion berm or swale Route clean water around disturbed soil Upslope run-on control Sending concentrated flow onto an unprotected slope

Silt fence Trap sediment from shallow sheet flow Down-gradient perimeter Installing across channels or deep flow

Inlet protection Keep sediment out of storm drains Active paved/graded areas Blocking the inlet so streets flood

Check dam Slow concentrated ditch flow Temporary channels/swales Letting flow bypass the ends

Sediment trap or basin Detain runoff and settle sediment Larger drainage areas Forgetting cleanout volume and access

Stabilized entrance Reduce track-out Construction access points Treating it as a street-sweeping substitute

Outlet protection (riprap apron) Prevent scour Pipe and culvert outlets Ending a high-velocity pipe on bare soil

Design and Calculation Workflow

Map disturbance and drainage. Identify disturbed acres, off-site run-on, discharge points, receiving waters, slopes, stockpiles, and existing inlets.

Keep clean water clean. Divert upslope runoff around disturbed soil; smaller dirty drainage areas are far easier to control.

Select erosion prevention first. Preserve vegetation, phase grading, stabilize inactive areas within the permit timeframe, and protect steep slopes with blankets or turf reinforcement.

Add sediment controls at logical collection points. Perimeter controls, inlet protection, traps, and basins go where runoff actually concentrates.

Check concentrated-flow energy. Channels, pipe outlets, culverts, and downspouts may need lining, check dams, riprap, or energy dissipation.

Apply sizing criteria. Common rules of thumb: a sediment trap sized near 3,600 ft^3 of storage per acre and a sediment basin near 3,600 ft^3 per acre of drainage (many states specify the figure). Example: at 3,600 ft^3 per disturbed acre, a 4.5-acre area requires 4.5 x 3,600 = 16,200 ft^3.

Plan inspection and maintenance. Typical permits require inspection at least every 7 days and within 24 hours of a qualifying storm (often 0.5 inch). A BMP that is undermined, full, clogged, or bypassed is failed until repaired.

Temporary vs Permanent BMP Thinking

Temporary construction BMPs control risk while the site is unstable: silt fence, temporary sediment basins, construction entrances, check dams, mulch, temporary seeding, inlet protection. Permanent BMPs are part of the finished drainage and water-quality system: vegetated swales, bioretention areas, detention or retention ponds, infiltration practices, stable channels, and riprap outlet aprons that often serve as both treatment and final landscape.

The exam may describe a BMP that sounds helpful but is hydraulically mismatched. Silt fence traps sheet-flow sediment but must never act as a channel dam, and it is rated for only a small contributing area (commonly about 0.25 acre per 100 ft of fence on slopes flatter than about 2 percent). Inlet protection reduces sediment to the storm sewer, but if it creates unsafe ponding or diverts muddy water around the inlet, it needs reconfiguration. A riprap apron controls outlet scour but does not replace upstream erosion prevention.

A final WRE concept is the trapping (removal) efficiency of a sediment basin, which depends on the ratio of the particle settling velocity to the basin overflow rate (surface loading). Because settling velocity scales with the square of particle diameter (Stokes' law), basins readily capture sand and coarse silt but pass clay-size fines, which is why turbidity, not just visible sediment, often governs discharge limits and why source-control erosion prevention beats end-of-pipe capture. The best PE answer usually combines source control, flow control, sediment capture, and maintenance, mirroring real WRE practice.