Study guide

7.3 Bearing Capacity and Slope Stability

NCEES PE Civil: Water Resources and Environmental Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: NCEES WRE Exam Spec and Reference Strategy

1.1 NCEES WRE Format 1.2 Reference Handbook and Units 1.3 Blueprint Prioritization

2 Chapter 6: WRE Project Planning, Cost, and Engineering Economics

6.1 Quantity Takeoff and Unit Basis 6.2 Cost Estimating and Bid Item Logic 6.3 Schedules, Sequencing, and Critical Path 6.4 Present Worth, Life-Cycle Cost, and Sustainability

3 Chapter 7: Soil Mechanics for WRE Problems

7.1 Lateral Earth Pressure and Retaining Situations 7.2 Consolidation, Compaction, and Settlement 7.3 Bearing Capacity and Slope Stability 7.4 Soil Data, Boring Logs, and Unit Conversions

4 Chapter 8: WRE Analysis and Hydraulic Design Foundations

8.1 Mass Balance and Hydraulic Loading 8.2 Solids Loading and Sludge Mass Balance 8.3 Hydraulic Flow Measurement and Instrumentation 8.4 Design Checks, Safety Factors, and Reasonableness

5 Chapter 9: WRE Hydrology, Runoff, and Storage Routing

9.1 Design Storms, IDF, and Time of Concentration 9.2 Rational Method and Peak Flow Limits 9.3 NRCS Curve Number and Unit Hydrographs 9.4 Detention, Retention, and Routing Checks

6 Chapter 10: Closed Conduit and Open Channel Hydraulics

10.1 Continuity, Energy, and HGL/EGL 10.2 Pipe Flow Losses, Pumps, and Net Head 10.3 Manning, Open Channel, and Critical Flow 10.4 Culverts, Weirs, Orifices, and Control Sections

7 Chapter 11: Groundwater, Wells, and Aquifer Flow

11.1 Darcy Law, Gradient, and Flow Area 11.2 Confined and Unconfined Aquifers and Storage 11.3 Well Drawdown, Specific Capacity, and Interference 11.4 Contaminant Transport and Dewatering Decisions

8 Chapter 12: Water Quality Chemistry and Pollutant Loading

12.1 Concentration, Load, and Mass-Rate Conversions 12.2 BOD, CBOD, DO, and Oxygen Demand 12.3 Nutrients, pH, Alkalinity, and Buffering 12.4 Pollutant Allocation, TMDL, and Water Quality Criteria

9 Chapter 13: Water Treatment Processes and Design Checks

13.1 Coagulation, Flocculation, and Sedimentation 13.2 Filtration, Disinfection, and CT Logic 13.3 Softening, Iron, Manganese, and Chemical Feed 13.4 Treatment Plant Hydraulics and Operations

10 Chapter 14: Wastewater Collection, Treatment, and Sludge

14.1 Collection-System Hydraulics and Infiltration 14.2 Preliminary, Primary, and Secondary Treatment 14.3 Nutrient Removal and Effluent Quality 14.4 Sludge Processing, Digestion, and Dewatering

11 Chapter 3: Water Quality, Treatment, and Sitework

Water Quality and Regulation Drinking Water and Wastewater Treatment Project Sitework and Final Review

12 Chapter 15: Sitework, Drainage, and Erosion Control

15.1 Grading, Cut/Fill, and Earthwork Balancing 15.2 Storm Drain Inlets and Minor Systems 15.3 Erosion, Sediment Control, and BMPs 15.4 Permitting, Constructability, and Field Adjustments

13 Chapter 4: Materials, Analysis, and Design for WRE

4.1 Materials and Pipe Selection 4.2 Analysis and Design Workflow 4.3 Site-Civil Constructability

14 Chapter 16: Materials, Pipes, Standards, and Reference Navigation

16.1 Pipe Material Selection and Failure Modes 16.2 Concrete, Soil, and Geosynthetic Materials 16.3 Design Standard Navigation and Revision Years 16.4 Reference Search Drills and Unit Checks

15 Chapter 18: Pumps, Distribution, and Collection Systems

18.1 Pump Curves, System Curves, and Operating Point 18.2 Water Distribution Pressure, Demand, and Storage 18.3 Sewer Collection, Lift Stations, and Force Mains 18.4 Transient, Surge, and Operational Troubleshooting

16 Chapter 19: WRE Calculation Workbook and Unit Drills

19.1 Flow, Concentration, and Load Workbook 19.2 Hydraulics Energy and Head Workbook 19.3 Treatment and Process Sizing Workbook 19.4 Error Patterns and Repair Drills

17 Chapter 5: Mixed Practice, Units, and Final Review

Formula Selection and Units Mixed WRE Mock Review Exam Day and Spec Transition

18 Chapter 17: Full-Length WRE Mixed Practice and Final Review

17.1 Eighty-Question Mock Exam Plan 17.2 Miss-Log Diagnostics by Domain 17.3 Calculator, Reference, and Break Strategy 17.4 Final-Week Current vs 2027 Spec Check

7.3 Bearing Capacity and Slope Stability

Key Takeaways Explain This Topic AI

Bearing capacity guards against shear failure under footings; settlement guards serviceability. WRE structures frequently need both checks.

Allowable bearing pressure equals ultimate capacity divided by a factor of safety (often 2.5 to 3), with care over gross versus net pressure.

The Terzaghi form qult = c Nc + q Nq + 0.5 gamma B Ngamma splits resistance into cohesion, surcharge, and soil-weight terms.

Groundwater lowers effective unit weight and can reduce the soil-weight term, so bearing and slope problems near water should not assume dry soil.

Slope stability balances driving forces against resisting shear strength; rapid drawdown is a classic critical WRE condition.

Last updated: June 2026

Soil Strength Problems Behind Water Projects

The WRE Soil Mechanics scope includes bearing capacity and slope stability because water structures are built on and in soil. A pump station, valve vault, tank, clarifier, basin embankment, channel bank, or wall footing can be controlled by the ground beneath it. You do not need to be a geotechnical specialist, but you must recognize the failure mode and use the correct stress basis.

Bearing Capacity Basics

Bearing capacity is the soil support limit under a footing or mat. The ultimate bearing capacity qult is the pressure at shear failure; the allowable bearing pressure qall is usually qult divided by a factor of safety, typically 2.5 to 3, unless a geotechnical report gives a serviceability-based allowable directly.

The general Terzaghi strip-footing form is qult = c Nc + q Nq + 0.5 gamma B Ngamma, with three resistance sources: cohesion (c Nc), surcharge at footing level (q Nq), and soil weight below the footing (0.5 gamma B Ngamma). The bearing factors Nc, Nq, and Ngamma depend only on the friction angle phi. The exam often supplies the factors or a simplified qult, so prioritize correct setup and gross/net interpretation.

Gross pressure is the full applied pressure at foundation level, including the structure plus backfill over the footing.

Net pressure subtracts the pressure of soil removed by excavation (the prior overburden at that depth). Net allowable = net ultimate / FS.

  • Bearing item What it checks WRE example
  • Ultimate capacity Shear failure below the footing Pump-station mat, tank footing
  • Allowable pressure qult / FS or report limit Spread-footing service check
  • Net pressure Added pressure beyond removed overburden Excavated vault or wet well
  • Settlement Deformation under service load Clarifier levelness, pipe penetrations
  • Eccentricity Uneven pressure distribution Retaining-wall or overturning risk

Groundwater matters: if the water table rises into the bearing zone, use the buoyant unit weight in the soil-weight term, which reduces qult. For WRE footings near basins, streams, or wet wells, never assume dry soil unless stated.

Slope Stability Basics

Slope stability compares resisting shear strength to driving forces, expressed as a factor of safety FS = resisting / driving. FS greater than 1 means resistance exceeds demand under the assumed model, but design criteria commonly require FS of 1.3 to 1.5 for long-term static conditions and higher under seismic loads. WRE slopes include levee embankments, pond banks, channel side slopes, lagoon berms, and temporary cuts.

Driving force rises with added fill, traffic, stockpiles, or stored water. Resistance falls with seepage, high pore pressure, weak clay seams, poor compaction, toe undercutting at a channel, or vegetation loss. Rapid drawdown is the signature WRE case: an outside pool drops faster than the embankment can drain, so the slope loses its external water support while internal pore pressures remain high, cutting effective stress and resistance.

Calculation and Judgment Workflow

Identify the structure or slope and the likely failure surface.

Decide short-term undrained, long-term drained, or a stated simplified model.

Use effective stress when pore pressure affects drained strength.

Convert ultimate to allowable with the specified FS.

Compare service load to qall, or compute the slope FS.

Re-check whether groundwater, surcharge, toe erosion, or drawdown changes the answer.

Worked Example: Bearing with a High Water Table

A 6 ft square footing bears 4 ft deep in sand, phi = 32 degrees, gamma = 120 pcf. Take Nq = 23 and Ngamma = 30 (supplied). With the water table well below the footing, the soil-weight term uses gamma = 120 pcf. If instead the water table rises to the footing base, that term uses gamma_b = 120 - 62.4 = 57.6 pcf, roughly halving the 0.5 gamma B Ngamma contribution.

Surcharge term: q Nq = (4 x 120) x 23 = 11,040 psf.

Soil-weight term, dry: 0.5 x 120 x 6 x 30 = 10,800 psf.

Soil-weight term, submerged: 0.5 x 57.6 x 6 x 30 = 5,184 psf.

The submerged case drops qult by about 5,600 psf, near a 25 percent reduction here. For WRE footings near wet wells, basins, and streams this is a routine, decisive effect.

Slope Stability Quick Reference

For a simple infinite slope in cohesionless soil with seepage parallel to the slope, FS = (gamma_b / gamma_sat) x (tan phi / tan beta), where beta is the slope angle. Dry or no-seepage cohesionless slope reduces to FS = tan phi / tan beta. These show why a slope stable when dry can drop below 1.0 once seepage develops.

  • Condition Effect on FS WRE example
  • Added crest fill or stockpile Lowers FS (more driving) Raising a levee
  • Seepage / high pore pressure Lowers FS (less effective stress) Saturated pond bank
  • Rapid drawdown Lowers FS sharply Detention basin emptied fast
  • Toe berm or buttress Raises FS Levee stabilization
  • Drainage / lowered phreatic line Raises FS Toe drains, relief wells

Typical minimum design FS values are about 1.5 for long-term static, 1.3 for end-of-construction or rapid drawdown, and 1.0 to 1.1 for pseudo-static seismic, though exam problems will state the criterion.

WRE Exam Traps

A bearing answer can be arithmetically right yet wrong if a net service pressure is compared to a gross allowable, or if a rising water table was ignored in the soil-weight term. A slope answer fails if it treats a dry cut as still stable once seepage begins. When the prompt mentions cracks, seepage exits, soft clay, recent filling, or channel toe erosion, the correct choice usually addresses the geotechnical mechanism, not a hydraulic tweak.