Study guide
7.4 Soil Data, Boring Logs, and Unit Conversions
NCEES PE Civil: Water Resources and Environmental Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: NCEES WRE Exam Spec and Reference Strategy
1.1 NCEES WRE Format 1.2 Reference Handbook and Units 1.3 Blueprint Prioritization
2 Chapter 6: WRE Project Planning, Cost, and Engineering Economics
6.1 Quantity Takeoff and Unit Basis 6.2 Cost Estimating and Bid Item Logic 6.3 Schedules, Sequencing, and Critical Path 6.4 Present Worth, Life-Cycle Cost, and Sustainability
3 Chapter 7: Soil Mechanics for WRE Problems
7.1 Lateral Earth Pressure and Retaining Situations 7.2 Consolidation, Compaction, and Settlement 7.3 Bearing Capacity and Slope Stability 7.4 Soil Data, Boring Logs, and Unit Conversions
4 Chapter 8: WRE Analysis and Hydraulic Design Foundations
8.1 Mass Balance and Hydraulic Loading 8.2 Solids Loading and Sludge Mass Balance 8.3 Hydraulic Flow Measurement and Instrumentation 8.4 Design Checks, Safety Factors, and Reasonableness
5 Chapter 9: WRE Hydrology, Runoff, and Storage Routing
9.1 Design Storms, IDF, and Time of Concentration 9.2 Rational Method and Peak Flow Limits 9.3 NRCS Curve Number and Unit Hydrographs 9.4 Detention, Retention, and Routing Checks
6 Chapter 10: Closed Conduit and Open Channel Hydraulics
10.1 Continuity, Energy, and HGL/EGL 10.2 Pipe Flow Losses, Pumps, and Net Head 10.3 Manning, Open Channel, and Critical Flow 10.4 Culverts, Weirs, Orifices, and Control Sections
7 Chapter 11: Groundwater, Wells, and Aquifer Flow
11.1 Darcy Law, Gradient, and Flow Area 11.2 Confined and Unconfined Aquifers and Storage 11.3 Well Drawdown, Specific Capacity, and Interference 11.4 Contaminant Transport and Dewatering Decisions
8 Chapter 12: Water Quality Chemistry and Pollutant Loading
12.1 Concentration, Load, and Mass-Rate Conversions 12.2 BOD, CBOD, DO, and Oxygen Demand 12.3 Nutrients, pH, Alkalinity, and Buffering 12.4 Pollutant Allocation, TMDL, and Water Quality Criteria
9 Chapter 13: Water Treatment Processes and Design Checks
13.1 Coagulation, Flocculation, and Sedimentation 13.2 Filtration, Disinfection, and CT Logic 13.3 Softening, Iron, Manganese, and Chemical Feed 13.4 Treatment Plant Hydraulics and Operations
10 Chapter 14: Wastewater Collection, Treatment, and Sludge
14.1 Collection-System Hydraulics and Infiltration 14.2 Preliminary, Primary, and Secondary Treatment 14.3 Nutrient Removal and Effluent Quality 14.4 Sludge Processing, Digestion, and Dewatering
11 Chapter 3: Water Quality, Treatment, and Sitework
Water Quality and Regulation Drinking Water and Wastewater Treatment Project Sitework and Final Review
12 Chapter 15: Sitework, Drainage, and Erosion Control
15.1 Grading, Cut/Fill, and Earthwork Balancing 15.2 Storm Drain Inlets and Minor Systems 15.3 Erosion, Sediment Control, and BMPs 15.4 Permitting, Constructability, and Field Adjustments
13 Chapter 4: Materials, Analysis, and Design for WRE
4.1 Materials and Pipe Selection 4.2 Analysis and Design Workflow 4.3 Site-Civil Constructability
14 Chapter 16: Materials, Pipes, Standards, and Reference Navigation
16.1 Pipe Material Selection and Failure Modes 16.2 Concrete, Soil, and Geosynthetic Materials 16.3 Design Standard Navigation and Revision Years 16.4 Reference Search Drills and Unit Checks
15 Chapter 18: Pumps, Distribution, and Collection Systems
18.1 Pump Curves, System Curves, and Operating Point 18.2 Water Distribution Pressure, Demand, and Storage 18.3 Sewer Collection, Lift Stations, and Force Mains 18.4 Transient, Surge, and Operational Troubleshooting
16 Chapter 19: WRE Calculation Workbook and Unit Drills
19.1 Flow, Concentration, and Load Workbook 19.2 Hydraulics Energy and Head Workbook 19.3 Treatment and Process Sizing Workbook 19.4 Error Patterns and Repair Drills
17 Chapter 5: Mixed Practice, Units, and Final Review
Formula Selection and Units Mixed WRE Mock Review Exam Day and Spec Transition
18 Chapter 17: Full-Length WRE Mixed Practice and Final Review
17.1 Eighty-Question Mock Exam Plan 17.2 Miss-Log Diagnostics by Domain 17.3 Calculator, Reference, and Break Strategy 17.4 Final-Week Current vs 2027 Spec Check
7.4 Soil Data, Boring Logs, and Unit Conversions
Key Takeaways Explain This Topic AI
Boring logs are point-in-time observations, so WRE decisions must weigh spatial variability, groundwater timing, and sample quality between borings.
USCS classification starts with percent passing the No. 200 sieve, then uses gradation for coarse soils and Atterberg limits for fine soils.
Groundwater levels on logs are time-sensitive; a 24-hour stabilized reading can differ from a drilling reading or seasonal high.
SPT N-values indicate relative density or consistency but are affected by hammer energy, gravel, and depth and need correction.
The WRE exam mixes SI and US Customary units, so soil questions require clean conversion among pcf, psf, tsf, kPa, and kN/m3.
Last updated: June 2026
Reading Soil Data Like a WRE Engineer
Under the April 2024 WRE specification, soil classification and boring-log interpretation sit in the Materials reporting group, while Soil Mechanics carries lateral pressure, consolidation, compaction, bearing capacity, settlement, and slope stability. In practice these are linked: a boring log may be the only warning that a sewer trench crosses soft clay, a basin outlet rests on loose sand, or a pump-station excavation will hit groundwater.
What a Boring Log Can and Cannot Prove
A boring log records observations at one location and time. It may carry soil descriptions, Unified Soil Classification System (USCS) symbols, sample depths, standard penetration test (SPT) N-values, groundwater observations, lab water content, dry density, Atterberg limits, grain-size data, and drilling remarks. It does not prove the same soil exists everywhere between borings, which is why spacing and judgment matter.
- Log item Useful meaning Caution
- Soil description Visual-manual classification clue Subject to sampler and logger judgment
- USCS group symbol Engineering-behavior shorthand (SW, ML, CH) Quality depends on lab vs field method
- SPT N-value Relative density or consistency Affected by energy, gravel, depth; needs N60/(N1)60 correction
- Groundwater note Water observed during/after drilling Seasonal and delayed response differ
- Atterberg limits Plasticity of fine soils Must be tied to fines content
- Unit weight / water content Phase-relationship input Confirm wet vs dry basis
Groundwater notes deserve special care. A note of water at 6 ft during drilling and 9 ft after 24 hours may reflect drilling disturbance, perched water, low permeability, or delayed stabilization. Excavation planning must not assume the site is dry below 9 ft, and a dry-season boring may not represent spring groundwater near a channel or basin.
Classification Workflow
Use a structured approach instead of guessing from a name:
Check percent passing the No. 200 sieve. More than 50 percent fines means fine-grained behavior; 50 percent or less means coarse-grained.
For coarse soils, split gravel from sand and judge gradation (well-graded W vs poorly graded P) and fines.
For fine soils, plot liquid limit and plasticity index on the plasticity chart to separate lean clay (CL), fat clay (CH), silt (ML/MH), and organic soils.
Connect classification to WRE performance: permeability, erosion risk, compressibility, bedding suitability, and compaction response.
Use lab and field data together; a single description like silty sand is not enough for a settlement or stability decision.
A clean sand may be permeable and good for drainage, yet vulnerable to running ground below the water table in an excavation. A plastic clay has low permeability but high consolidation settlement. A gravelly soil may be strong but hard to sample and classify from ordinary split-spoon data.
Unit Conversions That Prevent Wrong Answers
Because the exam mixes SI and US Customary units, soil conversions often involve force per area and unit weight:
1 tsf = 2,000 psf, approximately 95.8 kPa.
1 pcf is approximately 0.157 kN/m3.
1 ft = 0.3048 m and 1 in = 25.4 mm.
Vertical soil stress is unit weight times depth: pcf x ft = psf.
Water unit weight is about 62.4 pcf or 9.81 kN/m3.
1 psi = 144 psf, and 1 kPa is about 20.9 psf.
SPT N-Value Interpretation
SPT N-values are a frequent log entry and a quick consistency screen. Approximate correlations (uncorrected field N) help sanity-check a description:
- N (blows/ft) Sand relative density Clay consistency (approx)
- 0 to 4 Very loose Very soft
- 4 to 10 Loose Soft to medium
- 10 to 30 Medium dense Stiff
- 30 to 50 Dense Very stiff
- Over 50 Very dense Hard
Field N must be corrected to N60 for hammer energy and, for sands, to (N1)60 for overburden before use in design correlations. A low N near a planned excavation flags running ground or low bearing; a description of soft clay with N = 2 should immediately raise settlement and slope concerns.
Worked Unit Conversion
A report lists a clay undrained shear strength su = 1.2 tsf. Convert for a problem given in SI: 1.2 x 2,000 = 2,400 psf, and 2,400 psf x (1 kPa / 20.9 psf) = about 115 kPa. If a problem then asks for the vertical effective stress at 15 ft in soil with gamma = 118 pcf above a water table at 5 ft (gamma_sat = 122 pcf below): total stress = 5 x 118 + 10 x 122 = 590 + 1,220 = 1,810 psf; pore pressure = 62.4 x 10 = 624 psf; effective stress = 1,810 - 624 = 1,186 psf. Labeling each term as total, pore, or effective prevents the classic mix-up.
Exam Strategy
Before calculating, label every value as wet, dry, total, effective, allowable, ultimate, gross, or net, then convert units in a single line while preserving the basis. If a log shows soft clay from 8 to 20 ft with groundwater at 7 ft, a trench or footing item is not pure geometry; it is a soil-behavior problem carrying groundwater, sampling uncertainty, and constructability consequences. Treat one boring as a sample, not the truth for the whole site, and let the weakest credible layer and the highest credible water level drive the conservative answer the exam expects.