Study guide

14.2 Preliminary, Primary, and Secondary Treatment

NCEES PE Civil: Water Resources and Environmental Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: NCEES WRE Exam Spec and Reference Strategy

1.1 NCEES WRE Format 1.2 Reference Handbook and Units 1.3 Blueprint Prioritization

2 Chapter 6: WRE Project Planning, Cost, and Engineering Economics

6.1 Quantity Takeoff and Unit Basis 6.2 Cost Estimating and Bid Item Logic 6.3 Schedules, Sequencing, and Critical Path 6.4 Present Worth, Life-Cycle Cost, and Sustainability

3 Chapter 7: Soil Mechanics for WRE Problems

7.1 Lateral Earth Pressure and Retaining Situations 7.2 Consolidation, Compaction, and Settlement 7.3 Bearing Capacity and Slope Stability 7.4 Soil Data, Boring Logs, and Unit Conversions

4 Chapter 8: WRE Analysis and Hydraulic Design Foundations

8.1 Mass Balance and Hydraulic Loading 8.2 Solids Loading and Sludge Mass Balance 8.3 Hydraulic Flow Measurement and Instrumentation 8.4 Design Checks, Safety Factors, and Reasonableness

5 Chapter 9: WRE Hydrology, Runoff, and Storage Routing

9.1 Design Storms, IDF, and Time of Concentration 9.2 Rational Method and Peak Flow Limits 9.3 NRCS Curve Number and Unit Hydrographs 9.4 Detention, Retention, and Routing Checks

6 Chapter 10: Closed Conduit and Open Channel Hydraulics

10.1 Continuity, Energy, and HGL/EGL 10.2 Pipe Flow Losses, Pumps, and Net Head 10.3 Manning, Open Channel, and Critical Flow 10.4 Culverts, Weirs, Orifices, and Control Sections

7 Chapter 11: Groundwater, Wells, and Aquifer Flow

11.1 Darcy Law, Gradient, and Flow Area 11.2 Confined and Unconfined Aquifers and Storage 11.3 Well Drawdown, Specific Capacity, and Interference 11.4 Contaminant Transport and Dewatering Decisions

8 Chapter 12: Water Quality Chemistry and Pollutant Loading

12.1 Concentration, Load, and Mass-Rate Conversions 12.2 BOD, CBOD, DO, and Oxygen Demand 12.3 Nutrients, pH, Alkalinity, and Buffering 12.4 Pollutant Allocation, TMDL, and Water Quality Criteria

9 Chapter 13: Water Treatment Processes and Design Checks

13.1 Coagulation, Flocculation, and Sedimentation 13.2 Filtration, Disinfection, and CT Logic 13.3 Softening, Iron, Manganese, and Chemical Feed 13.4 Treatment Plant Hydraulics and Operations

10 Chapter 14: Wastewater Collection, Treatment, and Sludge

14.1 Collection-System Hydraulics and Infiltration 14.2 Preliminary, Primary, and Secondary Treatment 14.3 Nutrient Removal and Effluent Quality 14.4 Sludge Processing, Digestion, and Dewatering

11 Chapter 3: Water Quality, Treatment, and Sitework

Water Quality and Regulation Drinking Water and Wastewater Treatment Project Sitework and Final Review

12 Chapter 15: Sitework, Drainage, and Erosion Control

15.1 Grading, Cut/Fill, and Earthwork Balancing 15.2 Storm Drain Inlets and Minor Systems 15.3 Erosion, Sediment Control, and BMPs 15.4 Permitting, Constructability, and Field Adjustments

13 Chapter 4: Materials, Analysis, and Design for WRE

4.1 Materials and Pipe Selection 4.2 Analysis and Design Workflow 4.3 Site-Civil Constructability

14 Chapter 16: Materials, Pipes, Standards, and Reference Navigation

16.1 Pipe Material Selection and Failure Modes 16.2 Concrete, Soil, and Geosynthetic Materials 16.3 Design Standard Navigation and Revision Years 16.4 Reference Search Drills and Unit Checks

15 Chapter 18: Pumps, Distribution, and Collection Systems

18.1 Pump Curves, System Curves, and Operating Point 18.2 Water Distribution Pressure, Demand, and Storage 18.3 Sewer Collection, Lift Stations, and Force Mains 18.4 Transient, Surge, and Operational Troubleshooting

16 Chapter 19: WRE Calculation Workbook and Unit Drills

19.1 Flow, Concentration, and Load Workbook 19.2 Hydraulics Energy and Head Workbook 19.3 Treatment and Process Sizing Workbook 19.4 Error Patterns and Repair Drills

17 Chapter 5: Mixed Practice, Units, and Final Review

Formula Selection and Units Mixed WRE Mock Review Exam Day and Spec Transition

18 Chapter 17: Full-Length WRE Mixed Practice and Final Review

17.1 Eighty-Question Mock Exam Plan 17.2 Miss-Log Diagnostics by Domain 17.3 Calculator, Reference, and Break Strategy 17.4 Final-Week Current vs 2027 Spec Check

14.2 Preliminary, Primary, and Secondary Treatment

Key Takeaways Explain This Topic AI

Preliminary treatment (screening and grit removal) protects downstream pumps and tanks by removing rags, grit, and grease before settling or biological processes are stressed.

Primary clarifiers remove settleable solids and floatables; performance is described with surface overflow rate (SOR), detention time, weir loading, and percent removal (typically 25-40 percent BOD, 50-70 percent TSS).

Secondary treatment removes biodegradable organics biologically; activated sludge is governed by BOD load, mixed liquor suspended solids (MLSS), food-to-microorganism (F/M) ratio, and solids retention time (SRT).

Apply concentration removal directly only when flow is unchanged; otherwise convert to load (lb/day = MGD x mg/L x 8.34) before comparing units.

Effluent clues diagnose the failing unit: high TSS points to clarifier or settleability problems; high soluble BOD points to under-loaded or oxygen-starved biology.

Last updated: June 2026

Treatment Train Logic

Wastewater treatment is a sequence, not a list of isolated tanks. Materials are removed in the order that protects equipment, stabilizes flow, lowers solids and oxygen demand, and yields an effluent that can be disinfected or polished. The April 2024 WRE specification separates preliminary, primary, secondary, nutrient removal, solids handling, disinfection, and advanced treatment, so you should be able to state each step's purpose before you calculate.

Unit Roles

  • Unit or process Primary purpose Typical exam clue
  • Bar screen / fine screen Remove rags, wipes, plastics, large solids Pump clogging, screenings handling
  • Grit chamber Remove sand, gravel, grit Abrasion, deposition, ~1 ft/s control velocity
  • Primary clarifier Settle solids, skim floatables SOR, detention, sludge blanket
  • Aeration basin Oxidize soluble and fine particulate BOD Dissolved oxygen (DO), MLSS, F/M, SRT
  • Secondary clarifier Separate biological floc from water Return activated sludge, wasting, bulking, TSS

Preliminary treatment is mostly protection. Aerated and vortex grit chambers are sized to hold a control velocity near 1 ft/s so dense inorganic grit settles while lighter organics stay suspended. Too fast, grit passes; too slow, organics settle and turn septic.

Primary Treatment

Primary clarifiers remove settleable solids and scum and incidentally reduce BOD because particulate organics leave with the sludge. Typical removals are 25-40 percent BOD and 50-70 percent TSS . Design metrics:

Surface overflow rate (SOR) = Q / surface area, often 800-1,200 gpd/ft^2 at average flow.

Detention time = volume / Q, commonly 1.5-2.5 hours.

Weir loading rate = Q / total weir length, often under 20,000 gpd/ft.

Do not apply a primary removal percentage on the wrong basis. If flow is unchanged, concentration removal and load removal are numerically identical; if flow changes, use loads. Worked example: influent BOD 220 mg/L, removal 30 percent, so effluent = 220(1 - 0.30) = 154 mg/L. At 4 MGD, influent load = 4 x 220 x 8.34 = 7,339 lb/day; remaining load = 5,137 lb/day; removed = 2,202 lb/day, which is the dry solids feeding the digester from this stream.

Secondary Treatment

Secondary treatment targets biodegradable organics and biological solids. Activated sludge uses aeration, microorganisms, return activated sludge (RAS) , and waste activated sludge (WAS) . Trickling filters, rotating biological contactors (RBCs), oxidation ditches, lagoons, and sequencing batch reactors (SBRs) are alternative biological systems.

Core activated-sludge quantities:

Food load = Q x influent substrate (mg/L) x 8.34 (lb BOD/day).

Biomass inventory = basin volume x mixed liquor volatile suspended solids (MLVSS) x 8.34 (lb).

F/M ratio = food load / biomass inventory (typically 0.2-0.5/day conventional).

Hydraulic residence time (HRT) = basin volume / flow (4-8 hr conventional).

Solids retention time (SRT) = solids in system / solids leaving per day; set by wasting, not by HRT.

Dissolved oxygen drives the aerobes; aeration basins are typically held at about 2 mg/L DO . Low DO causes poor treatment, odors, filamentous bulking, and loss of nitrification; excess DO wastes energy and can shear floc.

Clarifier and Effluent Clues

Secondary clarifiers separate biological solids. High effluent TSS can mean hydraulic overload, poor settleability (high sludge volume index, or SVI), rising sludge from denitrification, a deep sludge blanket, or mechanical failure. High effluent BOD with low TSS points to soluble organics escaping biology. High BOD and high TSS together point to both biological and separation problems.

PE workflow: sketch the train from headworks to effluent; decide whether the question is hydraulic, solids, organic-load, or process diagnosis; convert concentration and flow to load when comparing units; use HRT, SOR, F/M, and removal efficiency only with compatible units; and reject answers that remove grit in a secondary clarifier or solve soluble BOD with a bar screen.

Comparing Biological Process Options

The exam frequently asks which secondary process fits a constraint. Conventional plug-flow activated sludge gives strong BOD removal but needs skilled operation. Extended aeration (oxidation ditches) runs at long SRT (20-30 days) and low F/M (0.05-0.15/day), producing well-stabilized sludge and tolerating load swings, which suits small communities. Trickling filters and RBCs are fixed-film systems with low energy and simple operation but limited cold-weather nitrification. SBRs combine reaction and settling in one tank on a timed cycle, saving footprint where flow is variable. Lagoons are land-intensive but cheap.

When a prompt stresses operator skill, footprint, energy, or flow variability, the answer is usually the process whose strength matches that single constraint.

Oxygen Transfer and Aeration Sizing

Aeration is the largest energy cost at most plants. The oxygen demand a basin must satisfy is the carbonaceous BOD oxidized plus, if nitrifying, the nitrogenous demand. A useful exam relationship is that field oxygen-transfer rate equals standard transfer rate times correction factors for alpha (wastewater vs. clean water), beta (salinity), temperature, and the driving-force ratio of saturation minus operating DO. Blower or diffuser sizing therefore follows from total pounds of oxygen per day divided by the field transfer efficiency.

If a question gives BOD load, an ammonia load, and a transfer efficiency, total the oxygen demand first (carbonaceous plus 4.57 lb O2 per lb ammonia-N) before converting to air or power, and do not forget the nitrogenous share when nitrification is required.