Study guide
12.1 Concentration, Load, and Mass-Rate Conversions
NCEES PE Civil: Water Resources and Environmental Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: NCEES WRE Exam Spec and Reference Strategy
1.1 NCEES WRE Format 1.2 Reference Handbook and Units 1.3 Blueprint Prioritization
2 Chapter 6: WRE Project Planning, Cost, and Engineering Economics
6.1 Quantity Takeoff and Unit Basis 6.2 Cost Estimating and Bid Item Logic 6.3 Schedules, Sequencing, and Critical Path 6.4 Present Worth, Life-Cycle Cost, and Sustainability
3 Chapter 7: Soil Mechanics for WRE Problems
7.1 Lateral Earth Pressure and Retaining Situations 7.2 Consolidation, Compaction, and Settlement 7.3 Bearing Capacity and Slope Stability 7.4 Soil Data, Boring Logs, and Unit Conversions
4 Chapter 8: WRE Analysis and Hydraulic Design Foundations
8.1 Mass Balance and Hydraulic Loading 8.2 Solids Loading and Sludge Mass Balance 8.3 Hydraulic Flow Measurement and Instrumentation 8.4 Design Checks, Safety Factors, and Reasonableness
5 Chapter 9: WRE Hydrology, Runoff, and Storage Routing
9.1 Design Storms, IDF, and Time of Concentration 9.2 Rational Method and Peak Flow Limits 9.3 NRCS Curve Number and Unit Hydrographs 9.4 Detention, Retention, and Routing Checks
6 Chapter 10: Closed Conduit and Open Channel Hydraulics
10.1 Continuity, Energy, and HGL/EGL 10.2 Pipe Flow Losses, Pumps, and Net Head 10.3 Manning, Open Channel, and Critical Flow 10.4 Culverts, Weirs, Orifices, and Control Sections
7 Chapter 11: Groundwater, Wells, and Aquifer Flow
11.1 Darcy Law, Gradient, and Flow Area 11.2 Confined and Unconfined Aquifers and Storage 11.3 Well Drawdown, Specific Capacity, and Interference 11.4 Contaminant Transport and Dewatering Decisions
8 Chapter 12: Water Quality Chemistry and Pollutant Loading
12.1 Concentration, Load, and Mass-Rate Conversions 12.2 BOD, CBOD, DO, and Oxygen Demand 12.3 Nutrients, pH, Alkalinity, and Buffering 12.4 Pollutant Allocation, TMDL, and Water Quality Criteria
9 Chapter 13: Water Treatment Processes and Design Checks
13.1 Coagulation, Flocculation, and Sedimentation 13.2 Filtration, Disinfection, and CT Logic 13.3 Softening, Iron, Manganese, and Chemical Feed 13.4 Treatment Plant Hydraulics and Operations
10 Chapter 14: Wastewater Collection, Treatment, and Sludge
14.1 Collection-System Hydraulics and Infiltration 14.2 Preliminary, Primary, and Secondary Treatment 14.3 Nutrient Removal and Effluent Quality 14.4 Sludge Processing, Digestion, and Dewatering
11 Chapter 3: Water Quality, Treatment, and Sitework
Water Quality and Regulation Drinking Water and Wastewater Treatment Project Sitework and Final Review
12 Chapter 15: Sitework, Drainage, and Erosion Control
15.1 Grading, Cut/Fill, and Earthwork Balancing 15.2 Storm Drain Inlets and Minor Systems 15.3 Erosion, Sediment Control, and BMPs 15.4 Permitting, Constructability, and Field Adjustments
13 Chapter 4: Materials, Analysis, and Design for WRE
4.1 Materials and Pipe Selection 4.2 Analysis and Design Workflow 4.3 Site-Civil Constructability
14 Chapter 16: Materials, Pipes, Standards, and Reference Navigation
16.1 Pipe Material Selection and Failure Modes 16.2 Concrete, Soil, and Geosynthetic Materials 16.3 Design Standard Navigation and Revision Years 16.4 Reference Search Drills and Unit Checks
15 Chapter 18: Pumps, Distribution, and Collection Systems
18.1 Pump Curves, System Curves, and Operating Point 18.2 Water Distribution Pressure, Demand, and Storage 18.3 Sewer Collection, Lift Stations, and Force Mains 18.4 Transient, Surge, and Operational Troubleshooting
16 Chapter 19: WRE Calculation Workbook and Unit Drills
19.1 Flow, Concentration, and Load Workbook 19.2 Hydraulics Energy and Head Workbook 19.3 Treatment and Process Sizing Workbook 19.4 Error Patterns and Repair Drills
17 Chapter 5: Mixed Practice, Units, and Final Review
Formula Selection and Units Mixed WRE Mock Review Exam Day and Spec Transition
18 Chapter 17: Full-Length WRE Mixed Practice and Final Review
17.1 Eighty-Question Mock Exam Plan 17.2 Miss-Log Diagnostics by Domain 17.3 Calculator, Reference, and Break Strategy 17.4 Final-Week Current vs 2027 Spec Check
12.1 Concentration, Load, and Mass-Rate Conversions
Key Takeaways Explain This Topic AI
Concentration is mass per volume; load is mass per time, so almost every pollutant-load problem requires multiplying concentration by flow.
The PE WRE shortcut lb/day = MGD x mg/L x 8.34 is only valid when flow is in million gallons per day and concentration is in milligrams per liter.
For conservative mixing, use a flow-weighted concentration, Cmix = sum(QC) / sum(Q), not an arithmetic average of sample concentrations.
A small sidestream can control the mass load if its concentration is high, even when its flow contribution is minor.
Unit consistency is the main scoring issue: cfs, gpm, MGD, L/s, kg/day, and lb/day must be converted before streams are combined.
Last updated: June 2026
Concentration, Load, and Mass Rate
The NCEES PE Civil Water Resources and Environmental (WRE) exam is a year-round, computer-based test of 80 questions scored on a criterion-referenced standard (no fixed percentage), delivered at Pearson VUE under a 9-hour appointment that includes the tutorial and one scheduled break. The April 2024 specification expects candidates to move comfortably between concentration, flow, and load. This appears in surface-water quality, groundwater contamination, wastewater treatment, solids loading, and total maximum daily load problems.
The exam often gives familiar water-quality units, then hides the actual task in the final sentence: find a load, a required concentration, a percent reduction, or the mixed concentration after two streams combine.
Concentration is pollutant mass per water volume, commonly mg/L. Load is pollutant mass per time, such as lb/day or kg/day. Mass rate is the same idea written generically; it states how much pollutant crosses a boundary each unit of time. A concentration by itself does not describe environmental impact unless the flow is known. A small flow at 1,000 mg/L may carry less total mass than a large flow at 20 mg/L.
Conversion Shortcuts
- Situation Use Notes
- U.S. water or wastewater load lb/day = Q (MGD) x C (mg/L) x 8.34 Most common PE WRE shortcut
- Stream load in cfs lb/day = Q (cfs) x C (mg/L) x 5.39 Combines cfs-to-MGD and 8.34
- Metric load kg/day = Q (m^3/day) x C (mg/L) / 1000 Because 1 mg/L = 1 g/m^3
- cfs to MGD MGD = cfs x 0.646 Useful for stream or stormwater flows
- gpm to MGD MGD = gpm x 0.00144 1,440 minutes per day
- Percent removal (Influent - Effluent) / Influent x 100% Use loads when flows differ
The 8.34 factor is the weight of one gallon of water in pounds (8.34 lb/gal); it converts MGD x mg/L to lb/day and is not interchangeable with metric formulas. The 5.39 factor equals 8.34 x 0.646 and lets you skip the cfs-to-MGD step. If a problem gives acre-ft/day, L/s, or other units, convert flow first or use a fully dimensional method rather than guessing a shortcut.
Calculation Workflow
Circle the requested output and its unit before computing anything.
Put every flow on one basis, usually MGD or m^3/day.
Put every concentration on one basis, usually mg/L.
Convert each stream to load before adding or subtracting pollutant mass.
If the answer must be a concentration, divide the resulting load by the resulting flow and conversion factor.
Confirm a blended conservative concentration falls between the input concentrations.
Mixing and Dilution
For a conservative pollutant with no reaction, settling, volatilization, decay, or chemical addition, the mixed concentration is a flow-weighted average:
Cmix = sum(Qi Ci) / sum(Qi)
This works only when consistent flow units are used. Do not average concentrations unless flows are equal. If a 4 MGD stream at 5 mg/L mixes with a 1 MGD stream at 45 mg/L, the result is (4 x 5 + 1 x 45) / 5 = 13 mg/L. The high-strength stream is only 20 percent of the flow yet contributes most of the pollutant mass.
Load-Based Removal
When flow changes through a process, percent removal must be based on load rather than concentration alone. This matters when sludge wasting, recycle streams, infiltration, evaporation, or chemical addition changes the water volume. For example, if influent is 2.0 MGD at 180 mg/L and effluent is 1.8 MGD at 30 mg/L, influent load is 2.0 x 180 x 8.34 = 3,002 lb/day and effluent load is 1.8 x 30 x 8.34 = 450 lb/day. Removal is (3,002 - 450) / 3,002 = 85 percent, lower than the 83 percent you would wrongly get from concentrations alone if you forgot the flow change.
Exam Traps
Use the concentration-load relationship as a unit audit. A load answer should carry mass per time. A concentration answer should carry mass per volume. A hydraulic answer such as gpd/ft^2 is not a pollutant load unless a concentration is also included. Before selecting a multiple-choice answer, estimate the order of magnitude: a municipal plant with MGD flow and tens of mg/L should produce hundreds or thousands of lb/day, not single digits. Distractors are commonly built by using the wrong factor (5.39 instead of 8.34), averaging concentrations instead of flow-weighting, or reporting kg/day where lb/day was requested.
Worked Stream-Combination Example
A river carries 40 cfs at a background nitrate of 1.5 mg/L. A treatment plant discharges 3.0 MGD effluent at 12 mg/L nitrate. Find the fully mixed downstream concentration. First put both on load. River load = 40 x 1.5 x 5.39 = 323 lb/day. Plant flow in MGD is already MGD, so plant load = 3.0 x 12 x 8.34 = 300 lb/day. Total load = 623 lb/day. Next combine flows on one basis: river flow = 40 x 0.646 = 25.8 MGD, plus 3.0 MGD = 28.8 MGD total. Mixed concentration = 623 / (28.8 x 8.34) = 2.6 mg/L. Notice the plant nearly equals the river in mass load (300 vs.
323 lb/day) despite carrying only about a tenth of the flow, because its concentration is eight times higher. That asymmetry is the recurring theme of load problems and the reason flow-weighting, not concentration averaging, is mandatory.
A reliable closing check on any combination problem: the mixed concentration must lie strictly between the lowest and highest input concentrations for a conservative substance. Here 2.6 mg/L sits between 1.5 and 12 mg/L, so the arithmetic is internally consistent. If your blended value lands outside that window, a unit or factor error occurred upstream in the calculation, most often mixing cfs and MGD without converting.