Study guide
Drinking Water and Wastewater Treatment
NCEES PE Civil: Water Resources and Environmental Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: NCEES WRE Exam Spec and Reference Strategy
1.1 NCEES WRE Format 1.2 Reference Handbook and Units 1.3 Blueprint Prioritization
2 Chapter 6: WRE Project Planning, Cost, and Engineering Economics
6.1 Quantity Takeoff and Unit Basis 6.2 Cost Estimating and Bid Item Logic 6.3 Schedules, Sequencing, and Critical Path 6.4 Present Worth, Life-Cycle Cost, and Sustainability
3 Chapter 7: Soil Mechanics for WRE Problems
7.1 Lateral Earth Pressure and Retaining Situations 7.2 Consolidation, Compaction, and Settlement 7.3 Bearing Capacity and Slope Stability 7.4 Soil Data, Boring Logs, and Unit Conversions
4 Chapter 8: WRE Analysis and Hydraulic Design Foundations
8.1 Mass Balance and Hydraulic Loading 8.2 Solids Loading and Sludge Mass Balance 8.3 Hydraulic Flow Measurement and Instrumentation 8.4 Design Checks, Safety Factors, and Reasonableness
5 Chapter 9: WRE Hydrology, Runoff, and Storage Routing
9.1 Design Storms, IDF, and Time of Concentration 9.2 Rational Method and Peak Flow Limits 9.3 NRCS Curve Number and Unit Hydrographs 9.4 Detention, Retention, and Routing Checks
6 Chapter 10: Closed Conduit and Open Channel Hydraulics
10.1 Continuity, Energy, and HGL/EGL 10.2 Pipe Flow Losses, Pumps, and Net Head 10.3 Manning, Open Channel, and Critical Flow 10.4 Culverts, Weirs, Orifices, and Control Sections
7 Chapter 11: Groundwater, Wells, and Aquifer Flow
11.1 Darcy Law, Gradient, and Flow Area 11.2 Confined and Unconfined Aquifers and Storage 11.3 Well Drawdown, Specific Capacity, and Interference 11.4 Contaminant Transport and Dewatering Decisions
8 Chapter 12: Water Quality Chemistry and Pollutant Loading
12.1 Concentration, Load, and Mass-Rate Conversions 12.2 BOD, CBOD, DO, and Oxygen Demand 12.3 Nutrients, pH, Alkalinity, and Buffering 12.4 Pollutant Allocation, TMDL, and Water Quality Criteria
9 Chapter 13: Water Treatment Processes and Design Checks
13.1 Coagulation, Flocculation, and Sedimentation 13.2 Filtration, Disinfection, and CT Logic 13.3 Softening, Iron, Manganese, and Chemical Feed 13.4 Treatment Plant Hydraulics and Operations
10 Chapter 14: Wastewater Collection, Treatment, and Sludge
14.1 Collection-System Hydraulics and Infiltration 14.2 Preliminary, Primary, and Secondary Treatment 14.3 Nutrient Removal and Effluent Quality 14.4 Sludge Processing, Digestion, and Dewatering
11 Chapter 3: Water Quality, Treatment, and Sitework
Water Quality and Regulation Drinking Water and Wastewater Treatment Project Sitework and Final Review
12 Chapter 15: Sitework, Drainage, and Erosion Control
15.1 Grading, Cut/Fill, and Earthwork Balancing 15.2 Storm Drain Inlets and Minor Systems 15.3 Erosion, Sediment Control, and BMPs 15.4 Permitting, Constructability, and Field Adjustments
13 Chapter 4: Materials, Analysis, and Design for WRE
4.1 Materials and Pipe Selection 4.2 Analysis and Design Workflow 4.3 Site-Civil Constructability
14 Chapter 16: Materials, Pipes, Standards, and Reference Navigation
16.1 Pipe Material Selection and Failure Modes 16.2 Concrete, Soil, and Geosynthetic Materials 16.3 Design Standard Navigation and Revision Years 16.4 Reference Search Drills and Unit Checks
15 Chapter 18: Pumps, Distribution, and Collection Systems
18.1 Pump Curves, System Curves, and Operating Point 18.2 Water Distribution Pressure, Demand, and Storage 18.3 Sewer Collection, Lift Stations, and Force Mains 18.4 Transient, Surge, and Operational Troubleshooting
16 Chapter 19: WRE Calculation Workbook and Unit Drills
19.1 Flow, Concentration, and Load Workbook 19.2 Hydraulics Energy and Head Workbook 19.3 Treatment and Process Sizing Workbook 19.4 Error Patterns and Repair Drills
17 Chapter 5: Mixed Practice, Units, and Final Review
Formula Selection and Units Mixed WRE Mock Review Exam Day and Spec Transition
18 Chapter 17: Full-Length WRE Mixed Practice and Final Review
17.1 Eighty-Question Mock Exam Plan 17.2 Miss-Log Diagnostics by Domain 17.3 Calculator, Reference, and Break Strategy 17.4 Final-Week Current vs 2027 Spec Check
Drinking Water and Wastewater Treatment
Key Takeaways Explain This Topic AI
NCEES assigns 6-9 questions to drinking water distribution and treatment and 7-11 questions to wastewater collection and treatment — together roughly a fifth of the 80-question exam.
Conventional surface-water treatment is rapid mix, coagulation, flocculation, sedimentation, filtration, then disinfection.
Disinfection effectiveness is set by CT = residual concentration (mg/L) × contact time (min); higher CT means more pathogen inactivation.
Key calculations: lb/day = mg/L × MGD × 8.34; detention time = volume/flow; surface overflow rate = flow/area; F/M ratio; and solids retention time (SRT).
Nitrification (ammonia→nitrate) needs aerobic conditions; denitrification (nitrate→N₂ gas) needs anoxic conditions plus a carbon source.
Last updated: June 2026
Treatment Is Process Selection Plus Loading
The WRE blueprint gives drinking water 6-9 questions and wastewater 7-11 questions , so treatment is roughly one-fifth of the 80-question exam. NCEES lists Recommended Standards for Water Works and the companion wastewater standards — the Ten States Standards — among the supplied electronic references. You do not memorize their tables; you recognize whether a problem wants process logic, hydraulic loading, solids loading, chemical dose, or operational interpretation.
Drinking-Water Treatment Train
A conventional surface-water plant follows this sequence:
Rapid mix disperses coagulant in seconds.
Coagulation destabilizes fine particles and colloids (commonly alum or ferric salts; alum consumes alkalinity).
Flocculation gently grows settleable floc (tapered mixing, several minutes to ~30 min).
Sedimentation removes most floc by gravity; design by surface overflow rate , not just detention time.
Filtration polishes remaining particles (rapid sand loading ≈ 2-3 gpm/ft²).
Disinfection inactivates pathogens and provides a distribution residual.
Disinfection is governed by CT = C × T (residual mg/L × contact time min). Required CT rises for hardier organisms — Giardia and viruses need more CT than vegetative bacteria, and Cryptosporidium resists chlorine almost entirely, pushing plants toward UV or ozone. Demand terms set sizing: average day is typical use, maximum day stresses supply/storage, peak hour stresses pipes, pumps, and pressure. Storage balances demand and fire reserve — it is not a treatment substitute.
- Goal Likely process Exam clue
- Reduce turbidity Coagulation→floc→sed→filtration Colloids, raw surface water
- Inactivate pathogens Chlorine, ozone, UV CT, residual, microbial target
- Lower hardness Lime softening, ion exchange, membranes Calcium, magnesium, scaling
- Remove taste/odor or trace organics Granular activated carbon, oxidation, membranes NOM, specific constituent
- Manage DBP risk Precursor removal, disinfectant choice THM, HAA, natural organic matter
- Wastewater Treatment Train
Collection is where the PE trap often sits. Infiltration is groundwater entering through pipe defects (slow, seasonal); inflow is direct stormwater through roof drains, cleanouts, and cross-connections (fast, storm-driven). Together ( I&I ) they overload lift stations and clarifiers.
Treatment then runs physical → biological → polishing. Preliminary removes rags and grit. Primary settles heavier solids and skims floatables (~30-40% BOD, 50-60% TSS removal). Secondary — activated sludge or fixed film — removes dissolved/colloidal biodegradable organics; well-run plants reach ~85%+ BOD/TSS removal , the classic secondary standard near 30 mg/L BOD₅ and 30 mg/L TSS. Nutrient removal is redox-driven: nitrification (NH₃→NO₃) needs aerobic conditions and oxygen, while denitrification (NO₃→N₂) needs anoxic zones with available carbon.
Activated Sludge Process Control
The activated-sludge questions reward a clear separation of water flow from solids flow from biology . The food-to-microorganism (F/M) ratio is the daily BOD load divided by the mass of mixed-liquor volatile suspended solids (MLVSS) in the aeration basin; a conventional plant runs F/M ≈ 0.2-0.5 lb BOD per lb MLVSS per day. The solids retention time (SRT) , also called mean cell residence time, is the total solids inventory divided by the solids wasted plus lost in the effluent each day.
SRT is the master control variable: short SRT (2-5 days) favors carbonaceous BOD removal only, while a longer SRT (8-15+ days) is needed to retain the slow-growing nitrifiers that convert ammonia to nitrate.
The sludge volume index (SVI) flags settling problems: a settled volume measured in a 30-minute test, divided by MLSS concentration, gives mL/g. SVI above ~150 mL/g signals bulking sludge that will carry solids over the clarifier weir. Return activated sludge (RAS) recycles settled biomass to maintain MLSS; waste activated sludge (WAS) removes excess growth to hold SRT constant.
Calculations To Keep Ready
Mass loading: lb/day = mg/L × MGD × 8.34.
Detention time: t = volume / flow (convert units first).
Surface overflow rate: SOR = flow / clarifier surface area (gpd/ft²).
Filter loading: gpm / filter area (ft²).
Food-to-microorganism (F/M) ratio: influent BOD load / MLVSS mass.
Solids retention time (SRT): solids inventory / solids leaving per day.
CT: disinfectant residual (mg/L) × contact time (min).
Worked dose: a plant treats 5.0 MGD and feeds chlorine at 3.2 mg/L, so 3.2 × 5.0 × 8.34 ≈ 133 lb/day — the 8.34 factor converts (mg/L)(MGD) to lb/day. Worked detention: a 0.5-MG clarifier passing 2.0 MGD has t = 0.5/2.0 = 0.25 day ≈ 6 hours , a typical primary value.
Exam Strategy
Read each stem twice — once for the treatment goal, once for the units. If the goal is pathogen control, do not answer with settling; if the goal is settleable solids, do not answer with activated carbon. Given mg/L and MGD, expect the 8.34 factor unless units are pre-converted. When a control term appears, classify it as water flow, solids flow, or biology — that single discipline prevents most wrong answers.
Common traps: confusing detention-time sizing with surface-overflow-rate sizing for clarifiers (settling depends on SOR, not depth or time alone); assuming chlorine handles Cryptosporidium (it does not — use UV or ozone); and running too short an SRT and then wondering why ammonia breaks through.