Study guide
13.3 Softening, Iron, Manganese, and Chemical Feed
NCEES PE Civil: Water Resources and Environmental Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: NCEES WRE Exam Spec and Reference Strategy
1.1 NCEES WRE Format 1.2 Reference Handbook and Units 1.3 Blueprint Prioritization
2 Chapter 6: WRE Project Planning, Cost, and Engineering Economics
6.1 Quantity Takeoff and Unit Basis 6.2 Cost Estimating and Bid Item Logic 6.3 Schedules, Sequencing, and Critical Path 6.4 Present Worth, Life-Cycle Cost, and Sustainability
3 Chapter 7: Soil Mechanics for WRE Problems
7.1 Lateral Earth Pressure and Retaining Situations 7.2 Consolidation, Compaction, and Settlement 7.3 Bearing Capacity and Slope Stability 7.4 Soil Data, Boring Logs, and Unit Conversions
4 Chapter 8: WRE Analysis and Hydraulic Design Foundations
8.1 Mass Balance and Hydraulic Loading 8.2 Solids Loading and Sludge Mass Balance 8.3 Hydraulic Flow Measurement and Instrumentation 8.4 Design Checks, Safety Factors, and Reasonableness
5 Chapter 9: WRE Hydrology, Runoff, and Storage Routing
9.1 Design Storms, IDF, and Time of Concentration 9.2 Rational Method and Peak Flow Limits 9.3 NRCS Curve Number and Unit Hydrographs 9.4 Detention, Retention, and Routing Checks
6 Chapter 10: Closed Conduit and Open Channel Hydraulics
10.1 Continuity, Energy, and HGL/EGL 10.2 Pipe Flow Losses, Pumps, and Net Head 10.3 Manning, Open Channel, and Critical Flow 10.4 Culverts, Weirs, Orifices, and Control Sections
7 Chapter 11: Groundwater, Wells, and Aquifer Flow
11.1 Darcy Law, Gradient, and Flow Area 11.2 Confined and Unconfined Aquifers and Storage 11.3 Well Drawdown, Specific Capacity, and Interference 11.4 Contaminant Transport and Dewatering Decisions
8 Chapter 12: Water Quality Chemistry and Pollutant Loading
12.1 Concentration, Load, and Mass-Rate Conversions 12.2 BOD, CBOD, DO, and Oxygen Demand 12.3 Nutrients, pH, Alkalinity, and Buffering 12.4 Pollutant Allocation, TMDL, and Water Quality Criteria
9 Chapter 13: Water Treatment Processes and Design Checks
13.1 Coagulation, Flocculation, and Sedimentation 13.2 Filtration, Disinfection, and CT Logic 13.3 Softening, Iron, Manganese, and Chemical Feed 13.4 Treatment Plant Hydraulics and Operations
10 Chapter 14: Wastewater Collection, Treatment, and Sludge
14.1 Collection-System Hydraulics and Infiltration 14.2 Preliminary, Primary, and Secondary Treatment 14.3 Nutrient Removal and Effluent Quality 14.4 Sludge Processing, Digestion, and Dewatering
11 Chapter 3: Water Quality, Treatment, and Sitework
Water Quality and Regulation Drinking Water and Wastewater Treatment Project Sitework and Final Review
12 Chapter 15: Sitework, Drainage, and Erosion Control
15.1 Grading, Cut/Fill, and Earthwork Balancing 15.2 Storm Drain Inlets and Minor Systems 15.3 Erosion, Sediment Control, and BMPs 15.4 Permitting, Constructability, and Field Adjustments
13 Chapter 4: Materials, Analysis, and Design for WRE
4.1 Materials and Pipe Selection 4.2 Analysis and Design Workflow 4.3 Site-Civil Constructability
14 Chapter 16: Materials, Pipes, Standards, and Reference Navigation
16.1 Pipe Material Selection and Failure Modes 16.2 Concrete, Soil, and Geosynthetic Materials 16.3 Design Standard Navigation and Revision Years 16.4 Reference Search Drills and Unit Checks
15 Chapter 18: Pumps, Distribution, and Collection Systems
18.1 Pump Curves, System Curves, and Operating Point 18.2 Water Distribution Pressure, Demand, and Storage 18.3 Sewer Collection, Lift Stations, and Force Mains 18.4 Transient, Surge, and Operational Troubleshooting
16 Chapter 19: WRE Calculation Workbook and Unit Drills
19.1 Flow, Concentration, and Load Workbook 19.2 Hydraulics Energy and Head Workbook 19.3 Treatment and Process Sizing Workbook 19.4 Error Patterns and Repair Drills
17 Chapter 5: Mixed Practice, Units, and Final Review
Formula Selection and Units Mixed WRE Mock Review Exam Day and Spec Transition
18 Chapter 17: Full-Length WRE Mixed Practice and Final Review
17.1 Eighty-Question Mock Exam Plan 17.2 Miss-Log Diagnostics by Domain 17.3 Calculator, Reference, and Break Strategy 17.4 Final-Week Current vs 2027 Spec Check
13.3 Softening, Iron, Manganese, and Chemical Feed
Key Takeaways Explain This Topic AI
Keep hardness, alkalinity, calcium, magnesium, lime, and soda-ash demands on an as-CaCO3 basis so they can be compared by equivalents.
Lime removes carbonate hardness; excess lime at high pH removes magnesium; soda ash (Na2CO3) is needed to precipitate noncarbonate calcium hardness.
Ion exchange swaps Ca and Mg for sodium, requires regeneration and brine handling, and adds sodium to the finished water.
Iron and manganese removal generally requires oxidation followed by filtration; sequestration only masks staining at low levels and does not remove the metals.
Chemical-feed math is a mass-rate problem: lb/day = MGD x dose (mg/L) x 8.34, then divide by the active fraction and convert liquids by density.
Last updated: June 2026
Why These Processes Are Tested Together
Hardness, iron, manganese, and chemical feed sit at the boundary between water chemistry and plant operation. The PE Civil WRE exam may ask a chemistry concept, then turn it into a design or operations calculation: pick a process, compute a feed rate, or explain why a finished water is scaling, staining, or generating complaints.
Hardness is mainly calcium and magnesium. For exam work, hardness and alkalinity are reported as mg/L as CaCO3 (equivalent weight 50 g/eq). Reporting as CaCO3 lets you add and subtract species by equivalents instead of raw mass. To convert an ion to as-CaCO3, multiply its mg/L by 50 / (equivalent weight of the ion). For calcium, equivalent weight is 40/2 = 20, so mg/L Ca x (50/20) = mg/L as CaCO3. Carbonate hardness is the portion of hardness matched by alkalinity; the excess is noncarbonate hardness .
Softening Process Selection
- Problem condition Likely process Design idea PE trap
- Carbonate hardness Lime softening Convert HCO3- to CO3 and precipitate CaCO3 Ignoring the alkalinity limit
- Magnesium hardness Excess lime, pH ~10.6-11 Precipitate Mg(OH)2 Forgetting recarbonation/pH control
- Noncarbonate Ca hardness Soda ash + lime Add CO3 to precipitate CaCO3 Assuming lime alone removes all
- Small-system hardness Ion exchange Exchange Ca/Mg for Na Ignoring regeneration and brine
High-purity demand Membranes / demineralization Remove dissolved ions broadly Treating membranes as particle filters
Lime-Soda Stabilization and Metals
Lime-soda softening leaves a high-pH water (often pH 10.5-11) and a CaCO3/Mg(OH)2 sludge. Practical finished hardness floors near 30-40 mg/L (CaCO3) and 10 mg/L (Mg(OH)2) because of solubility limits - you cannot soften to zero. The high-pH water is unstable and must be conditioned: recarbonation with carbon dioxide drops pH and converts excess carbonate chemistry toward a stable, slightly scale-forming water (positive Langelier Saturation Index) that protects pipe.
Ion exchange is operationally simpler but adds sodium, needs salt regeneration, and produces a concentrated waste brine; blending part of the raw water past the resin is a common way to hit a hardness target economically.
Iron and manganese occur as soluble reduced forms (Fe2+, Mn2+) in groundwater. Once exposed to oxygen or chlorine they oxidize to insoluble Fe(OH)3 and MnO2 that cause red/brown (iron) and black (manganese) staining. The Secondary MCLs are 0.3 mg/L iron and 0.05 mg/L manganese. Standard removal is oxidation then filtration : oxidants include aeration, chlorine, potassium permanganate (KMnO4), or ozone, with enough oxidant, pH, and contact time before the filter. Manganese needs higher pH and stronger oxidant than iron and is the harder of the two.
Sequestration with polyphosphates holds low metal concentrations in solution to limit staining but removes nothing. If a question asks for actual removal, choose oxidation plus filtration, not sequestration alone.
Chemical-Feed Calculation Workflow
The master relation is lb/day = flow (MGD) x dose (mg/L) x 8.34 , where 8.34 lb/gal is the weight of water. Steps:
Identify target active dose (mg/L) and design flow (MGD).
Active chemical lb/day = MGD x mg/L x 8.34.
Adjust for purity: product lb/day = active lb/day / active fraction.
For liquids, convert product lb/day to gal/day using solution density (lb/gal).
Confirm whether the stated dose is dry product, active ingredient, or neat solution.
Compare with feeder capacity and chemical storage duration if asked.
Worked Example
A plant wants a 2.0 mg/L active oxidant dose at 3.0 MGD. Active requirement is 3.0 x 2.0 x 8.34 = 50.0 lb/day. If the chemical is only 25% active, neat product is 50.0 / 0.25 = 200 lb/day. If the solution weighs 10 lb/gal, that is 20 gal/day. The classic wrong answer stops at 50 lb/day and forgets product strength.
Operations Checks
Feed must track actual flow. Flow-paced feed avoids underdosing at peak and overdosing at low flow. Plants also need standby feed pumps, calibration (drawdown) columns, day tanks, secondary containment, ventilation for incompatible chemicals (never store chlorine and ammonia or acid together), and residual monitoring. The correct operational answer usually closes the mass balance and keeps the chemical compatible with the process objective.
Equivalent-Weight Reference (as CaCO3)
To move any species to an as-CaCO3 basis, multiply its mg/L by 50 divided by the ion's equivalent weight. Memorizing the common equivalent weights speeds every softening problem:
- Calcium, Ca2+: eq wt 20, factor 2.50
- Magnesium, Mg2+: eq wt 12.2, factor 4.10
- Bicarbonate, HCO3-: eq wt 61, factor 0.82
- Carbon dioxide, CO2: eq wt 22, factor 2.27
- Quicklime, CaO: eq wt 28, factor 1.79
- Soda ash, Na2CO3: eq wt 53, factor 0.94
A classic lime-soda stoichiometry sequence: dose lime for CO2, then for carbonate hardness (the bicarbonate portion), then add excess lime for magnesium, and finally soda ash for noncarbonate calcium hardness. Skipping the CO2 demand or the magnesium step underdoses lime and leaves the question's hardness target unmet.
Stability and Corrosion
Finished water should be neither aggressively corrosive nor heavily scaling. The Langelier Saturation Index (LSI) compares actual pH to the pH of calcium carbonate saturation: a slightly positive LSI deposits a thin protective CaCO3 film, while a negative LSI dissolves pipe and can mobilize lead and copper. Softened, high-pH water is typically supersaturated and must be recarbonated; soft, low-alkalinity surface water is often corrosive and may need corrosion control under the Lead and Copper Rule. The exam may ask you to interpret an LSI sign rather than compute it - positive means scaling tendency, negative means corrosive.