Study guide

6.2 Fire Safety, Hot Work Permits & Extinguisher Operation

DOLE Construction Occupational Safety and Health COSH

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & DOLE OSH Framework

1.1 About the COSH SO2 Certification & Course Structure 1.2 How to Use This Study Guide & Exam Plan

2 Chapter 2: OSH Legislation, Standards & Safety Officer Roles

2.1 RA 11058, DO 198-18 & DO 252-25: Philippine OSH Law & Penalties 2.2 DOLE Department Order No. 13-98: Construction OSH Guidelines & CSHP 2.3 Rule 1030: Safety Officer Classification, Duties & Ratios 2.4 Rule 1040: Safety Committees & Site Safety Management

3 Chapter 3: Hazard Identification, Risk Assessment & Control (HIRAC)

3.1 Unsafe Acts vs. Unsafe Conditions & Hazard Categories 3.2 Job Hazard Analysis (JHA) & Risk Matrix Evaluation 3.3 Hierarchy of Controls in Construction Operations

4 Chapter 4: Construction Site Premises & High-Risk Operations

4.1 Construction Site Premises, Housekeeping & Access Control 4.2 Excavation, Trenching, and Soil Stabilization Safety 4.3 Structural Demolition Safety & Pre-Demolition Planning 4.4 Scaffold Assembly, Erection, Inspection & Tagging Systems 4.5 Heavy Equipment & Mobile Crane Lifting Operations 4.6 Fall Protection, Work at Heights & Lifelines 4.7 Environmental Safety, Pollution Control & Explosives on Construction Sites

5 Chapter 5: Tools, Materials, and Chemical Hazards

5.1 Hand and Power Tool Guarding & Electrical Tool Safety 5.2 Manual Material Handling, Rigging & Ergonomics 5.3 Chemical Safety, GHS Labeling & Safety Data Sheets (SDS)

6 Chapter 6: Electrical, Fire, Confined Space & PPE

6.1 Construction Electrical Safety & Lockout/Tagout (LOTO) 6.2 Fire Safety, Hot Work Permits & Extinguisher Operation 6.3 Emergency Preparedness, Evacuation & Site Response Plans 6.4 Confined Space Entry & Atmospheric Testing 6.5 Personal Protective Equipment (PPE) Selection & Maintenance

7 Chapter 7: OSH Administration, Inspection, Reporting & Program Re-entry

7.1 Accident Investigation, Root Cause Analysis & Evidence Gathering 7.2 Mandatory DOLE OSH Reporting: WAIR, AEDR & Timelines 7.3 Occupational Health, Medical Services & Workplace Hygiene 7.4 Toolbox Meetings & Communicating OSH on Site 7.5 Routine Construction Site Safety Inspection 7.6 Employees Compensation Program (ECC) for Construction Workers 7.7 Re-entry Planning & Construction OSH Program Implementation

6.2 Fire Safety, Hot Work Permits & Extinguisher Operation

Key Takeaways Explain This Topic AI

The Fire Tetrahedron consists of four essential elements: Fuel, Oxygen, Heat, and an Uninhibited Chemical Chain Reaction; removing any single element extinguishes the fire.

Fires are categorized into five distinct classes (A, B, C, D, K) based on fuel type, requiring specific extinguishing agents to prevent catastrophic fire spread.

Hot work operations (welding, cutting, grinding) require a pre-signed Hot Work Permit, a 35-foot (10.7m) cleared combustible radius, and a dedicated 30-minute post-job fire watch.

Portable fire extinguisher operation follows the PASS acronym: Pull the pin, Aim low at the base of the fire, Squeeze the lever, and Sweep side to side.

Water streams must NEVER be applied to Class B (flammable liquid) or Class C (energized electrical) fires due to boiling liquid dispersion and lethal shock hazards.

Last updated: July 2026

Fire Safety, Hot Work Permits & Extinguisher Operation

Fire hazards on construction sites present catastrophic risks to life safety, structural integrity, and asset protection. The combination of temporary wooden shoring, flammable solvents, diesel fuel storage, compressed gas cylinders, open flames, and spark-producing operations (hot work) requires strict enforcement of fire safety standards under DOLE OSHS Rule 1100 (Fire Protection and Control) and Fire Code of the Philippines (RA 9514).

1. Fire Dynamics & The Fire Tetrahedron Model

Understanding how fire starts, propagates, and extinguishes requires analyzing the combustion process at a chemical level.

From Fire Triangle to Fire Tetrahedron

For decades, fire dynamics was represented by the Fire Triangle comprising three elements: Fuel , Oxygen , and Heat . However, modern fire science incorporates a fourth critical dimension, creating the Fire Tetrahedron :

Fuel (Reducing Agent) : Combustible solid, liquid, or gas that ignites and sustains flaming.

Oxygen (Oxidizing Agent) : Atmospheric oxygen (normally 21% by volume). Combustion can sustain at oxygen levels as low as 15%.

Heat (Thermal Energy) : Energy required to raise the fuel to its ignition temperature (sparks, arcs, friction, open flame).

Uninhibited Chemical Chain Reaction : The rapid oxidation process producing free radicals (H, OH, O) that perpetuate flame propagation.

Extinguishment Principles

Extinguishing a fire requires removing or interrupting at least one element of the Fire Tetrahedron:

Cooling (Removing Heat): Applying water to lower fuel temperature below its flash point.

Smothering (Removing Oxygen): Applying foam, CO2, or a fire blanket to starve the fire of atmospheric oxygen.

Starving (Removing Fuel): Shutting off fuel gas supply valves or removing combustible materials from the fire path.

Chemical Chain Inhibition : Applying dry chemical agents (e.g., monoammonium phosphate) to react with free radicals and halt the combustion chain.

2. Classification of Fires & Extinguisher Compatibility

Fires are categorized into five distinct classes based on the physical state and chemical composition of the fuel involved. Using an incorrect extinguishing agent can violently exacerbate the fire or cause fatal injury to the operator.

Fire Class Fuel Type & Description Standard Symbol / Color Code Recommended Extinguisher Agent Prohibited Agent & Hazard

Class A Ordinary combustibles (wood, paper, cloth, trash, rubber, plastics) Green Triangle / Letter A Water, Pressurized Water, Foam, ABC Dry Chemical CO2 (poor cooling capacity on deep-seated embers)

Class B Flammable liquids & gases (gasoline, diesel, solvents, paint, propane) Red Square / Letter B Carbon Dioxide (CO2), ABC/BC Dry Chemical, Foam Straight Water Stream (causes boiling liquid spread & splatter)

Class C Energized electrical equipment (motors, switchboards, transformers, power tools) Blue Circle / Letter C Carbon Dioxide (CO2), ABC/BC Dry Chemical (Non-conductive) Water or Foam (conducts electricity causing severe shock hazard)

Class D Combustible metals (magnesium, titanium, zirconium, sodium, potassium) Yellow Star / Letter D Special Dry Powder (Met-L-X, Na-X, Copper Powder) Water, CO2, standard ABC (causes violent explosion or reaction)

Class K Commercial cooking fats and oils (vegetable oils, animal fats in fryers) Black Hexagon / Letter K Wet Chemical (Potassium Acetate / Potassium Carbonate) Water or CO2 (causes explosive steam expansion and oil boil-over)

3. Hot Work Permit System & Safe Operating Protocols

Hot Work is defined as any temporary operation involving open flames or producing heat, sparks, or slag. Examples include oxy-acetylene welding/cutting, electric arc welding, brazing, soldering, thermal spraying, and power grinding.

The Hot Work Permit-to-Work System

Before any hot work commences outside a designated permanent welding shop, a formal Hot Work Permit must be issued and signed by the site Safety Officer or designated Fire Safety Supervisor.

Pre-Inspection : The Safety Officer inspects the proposed work area, verifies atmospheric testing if near tanks/pipes, and confirms that fire control measures are in place.

35-Foot (10.7-Meter) Clear Radius Rule : All combustible materials (wood, trash, paper, flammable liquids) within a 35-foot radius of the hot work operation MUST be removed. If combustibles cannot be relocated, they must be covered and sealed with fire-resistant welding blankets or metal shields.

Protection of Openings : All wall penetrations, floor openings, pipe chases, and open drainage ducts within 35 feet must be covered or plugged with fire-rated material to prevent hot sparks or slag from falling into unseen lower compartments.

Compressed Gas Cylinder Safety : Oxygen and fuel gas (acetylene/LPG) cylinders must be secured upright in carts, equipped with flashback arrestors at both torch and regulator ends, and separated by at least 20 feet (6.1 meters) or a 5-foot high, 1-half-hour fire-rated barrier when in storage.

Mandatory Post-Hot-Work Fire Watch

A dedicated Fire Watch officer must be assigned to monitor the hot work area during operations and for a mandatory duration after work completion.

Duration : The fire watch MUST remain on post for at least 30 minutes after hot work is completed to check for smoldering embers, hidden sparks, or delayed ignition. In high-risk environments (e.g., wooden structures or polyurethane insulation), the fire watch duration may be extended to 60 minutes.

Sole Responsibility : The fire watch officer must have NO OTHER DUTIES. They must be equipped with an appropriate portable fire extinguisher (minimum 10-lb ABC dry chemical or CO2) and trained in emergency alarm activation.

4. Portable Fire Extinguisher Selection & PASS Operation

Portable fire extinguishers are first-line defense devices designed for incipient stage fires (fires in their initial phase that can be controlled without specialized turnout gear).

The PASS Technique

When operating a portable fire extinguisher, the operator must stand 6 to 8 feet back from the fire, maintain an unblocked exit path at their back, and execute the PASS protocol:

P - Pull : Pull the safety pin located at the top of the operating lever. This breaks the tamper seal.

A - Aim : Aim the extinguisher nozzle or hose low, pointing directly at the base of the fire (the burning fuel source), NOT at the flames floating in the air.

S - Squeeze : Squeeze the operating handle or lever to release the extinguishing agent.

S - Sweep : Sweep the nozzle from side to side across the base of the fuel source until the fire is completely extinguished. Re-inspect the area for rekindling.

Extinguisher Placement & Inspection Rules

Travel Distance : Maximum travel distance to a Class A extinguisher must not exceed 75 feet (22.9 meters) ; for Class B, maximum travel distance is 50 feet (15.2 meters) .

Monthly Inspection : Extinguishers must undergo monthly visual checks: verify pressure gauge needle is in the green zone, pull pin and seal intact, nozzle unobstructed, and annual hydrostatic test tag current.