Study guide
7.1 Plumbing & Sanitary Systems
PRC Architect Licensure Examination ALE
Track your progress as you read
Finished sections get a check mark.
1 Introduction
About the PRC Architect Licensure Examination (ALE) How the ALE Is Organized & Scored
2 Chapter 1: Philippine & World Architectural History
1.1 Pre-Colonial & Spanish Colonial Philippine Architecture 1.2 American Colonial Period, Filipino Modernism & National Artists for Architecture 1.3 World Architectural History: Classical Through Modern Movements
3 Chapter 2: Architectural Theory & Planning Principles
2.1 Architectural Theories & Design Philosophies 2.2 Urban & Regional Planning Principles 2.3 Environmental Psychology & Human Behavior in Design
4 Chapter 3: RA 9266 and the Legal Framework of Practice
3.1 RA 9266: The Architecture Act of 2004 3.2 The PRBoA, Licensure & Scope of Practice 3.3 Code of Ethical Conduct for Architects
5 Chapter 4: Professional Practice, Contracts & UAP Standards
4.1 UAP Standards of Professional Practice (SPP Documents) 4.2 Contract Documents, Delivery Methods & Specifications 4.3 Professional Liability, Insurance & Construction Administration
6 Chapter 5: Structural Conceptualization & Systems
5.1 Structural Loads & Systems 5.2 Seismic Design Principles & the NSCP (Seismic Zone 4) 5.3 Structural Materials: Concrete, Steel, Timber & Masonry
7 Chapter 6: Building Materials & Construction Methods
6.1 Building Materials & Specifications 6.2 Construction Methods, Sequencing, QC & Safety 6.3 Building Envelope: Waterproofing, Doors, Windows & Roofing
8 Chapter 7: Building Utilities
7.1 Plumbing & Sanitary Systems 7.2 Electrical Systems & Illumination Design 7.3 HVAC, Mechanical Systems & Acoustics
9 Chapter 8: PD 1096 — The National Building Code
8.1 PD 1096 Development Controls: PSO, TGFA, FLAR & Setbacks 8.2 PD 1096 Fire Safety, Light, Ventilation & Occupancy 8.3 Applying PD 1096: Worked Examples & Common Exam Traps
10 Chapter 9: Site Analysis & Climate-Responsive Design
9.1 Site Analysis: Topography, Environmental Factors & Context 9.2 Tropical Climate-Responsive Design 9.3 Sustainable & Green Design Principles
11 Chapter 10: Programming & Space Planning
10.1 Space Programming & Functional Relationships 10.2 Circulation Systems & Spatial Organization 10.3 Building Typologies & User Requirements
12 Chapter 11: Zoning, Development Controls & Accessibility
11.1 Zoning Regulations, Setbacks & Site Development 11.2 BP 344 Accessibility Law & Universal Design 11.3 Life Safety, Egress & Fire-Code Compliance in Design
13 Chapter 12: Urban Design & Site Planning Process
12.1 Urban Design Principles & Site Development Concepts 12.2 Site Planning Process: From Analysis to Concept 12.3 Landscape Architecture & Site Development Elements
14 Chapter 13: Architectural Graphics, Presentation & Design Exam Strategy
13.1 Architectural Graphics: Plans, Sections, Elevations & Scales 13.2 Presentation Techniques & Design Communication 13.3 The ALE Design Exam Format: Problem-Solving Approach 13.4 Design Strategy & Time Management
7.1 Plumbing & Sanitary Systems
Key Takeaways Explain This Topic AI
Republic Act No. 1378 (the Plumbing Law of 1955) licenses Master Plumbers; architects are tested on plumbing coordination, not plumbing design
The National Plumbing Code requires a minimum slope of 2% for sanitary drainage pipe 75 mm and smaller, and 1% for pipe 100 mm and larger
PD 1096 Section 903 requires an Imhoff or septic tank with a subsurface absorption field wherever no municipal sewer main is available
A tank-type water closet is commonly assigned around 4 Drainage Fixture Units (DFU), several times the load of a single lavatory (about 1 DFU)
Wet-wall stacking - aligning plumbing-heavy rooms vertically floor after floor - keeps soil and vent stacks running straight down without costly offsets
Last updated: July 2026
7.1 Plumbing & Sanitary Systems
Quick Answer: Plumbing design itself is the licensed scope of the Master Plumber under Republic Act No. 1378 (the Plumbing Law of 1955), but the ALE tests the architect's coordination knowledge: how water supply, sanitary drainage, venting, and on-site sewage treatment shape floor plans, wet walls, and pipe chases. The governing technical reference is the Revised National Plumbing Code of the Philippines (NPCP) , applied together with PD 1096's sanitation provisions (Section 903).
Architects rarely size a pipe, but they draw the walls the pipes live in, set the floor levels the pipes drain toward, and decide whether a project can even connect to a sewer main. Getting these decisions wrong is expensive to fix once the structural frame is up, which is why building-utilities coordination is examined as part of the Structural Design, Materials, and Utilities subject.
Water Supply Systems
A building's water supply system moves potable water from a source - a water district, a franchised concessionaire such as Manila Water or Maynilad in Metro Manila, a deep well, or a combination - to every fixture that needs it. Under the NPCP, potable water must meet the Philippine National Standards for Drinking Water (PNSDW) ; the architect's job is not testing water quality but making sure supply reaches every floor reliably.
Because municipal water pressure and availability are intermittent in much of the Philippines, most mid-rise and larger buildings use a strategy the architect must reserve space for:
Underground cistern (reservoir tank) - collects and stores municipal or well water at the ground floor or basement, sized as a buffer against supply interruptions.
Overhead/elevated tank - sits on the roof deck or a tank tower and feeds fixtures by gravity, topped up by a pump from the cistern.
Hydropneumatic (pressure) systems - used instead of, or alongside, gravity tanks in taller buildings where roof-tank height cannot deliver adequate pressure to lower floors, or where an elevated tank is architecturally undesirable.
The architect must also protect against cross-connection : a physical link between the potable supply and any non-potable source (irrigation, cistern overflow, fire system) that could let contaminated water siphon back into drinking water. The NPCP requires backflow-prevention devices (air gaps, vacuum breakers, or check valves) wherever this risk exists - for example, at hose bibbs, irrigation risers, and cooling-tower makeup connections.
Sanitary Drainage and Venting
Sanitary drainage carries wastewater from fixtures to the building sewer by gravity, which means slope is everything. The NPCP sets minimum slopes for horizontal drainage piping: generally 2% (about 1/4 inch per foot) for pipe 75 mm (3 inches) and smaller , and 1% (about 1/8 inch per foot) for pipe 100 mm (4 inches) and larger . Too little slope lets solids settle and the line clog; too much slope lets liquid outrun solids, stranding them - both defeat the self-scouring velocity the system depends on.
Every fixture connects to the drain through a trap - a curved section that holds a water seal to block sewer gas from entering occupied space. That seal only survives if the system is vented : a parallel network of pipes that admits air so drainage flow doesn't siphon the trap dry or push gas back through it. Common venting strategies an architect will see labeled on a plumbing plan include individual (fixture) vents, common vents shared by back-to-back fixtures, wet vents (a vent that also carries drainage from another fixture), and a stack vent that extends the main soil/waste stack through the roof.
Fixture Units: A Shared Design Language
Because a three-bedroom house and a twenty-story condominium cannot be piped the same way, the NPCP sizes supply and drainage piping using fixture unit values rather than exact flow rates - a standardized weighting that lets designers add up demand across many fixtures.
Concept What It Sizes Example Values
WSFU (Water Supply Fixture Unit) Supply pipe and meter sizing A lavatory carries a small WSFU load; a flush-valve water closet carries several times more
DFU (Drainage Fixture Unit) Waste/soil pipe and vent stack sizing Lavatory with 1-1/4 inch waste is about 1 DFU; a domestic kitchen sink with a 1-1/2 inch trap is about 2 DFU; a tank-type water closet is commonly assigned around 4 DFU - among the highest of ordinary fixtures
The takeaway for the exam is conceptual, not memorization of every table value: the fixture with the largest, fastest discharge (the water closet) drives drain and vent-stack sizing far more than any single lavatory or sink , so floor plans that cluster toilets on a shared stack must give that stack proportionally more capacity.
Septic Tanks and On-Site Sewage Treatment
Section 903 of PD 1096 requires that sanitary sewage be discharged into the nearest available street sewer main. Where no municipal sewer exists - true of most subdivisions and provincial sites - the Code requires an Imhoff tank or septic tank with a subsurface absorption field . The NPCP tables size septic tanks by occupancy driver: number of bedrooms for a single-family dwelling (with added capacity required beyond about five or six bedrooms), number of dwelling units for multi-family projects, and total DFU load for other uses. The absorption field's size depends on a percolation test of the actual soil, since clay-heavy sites absorb effluent far more slowly than sandy sites and may need a larger field or an alternative treatment approach. Larger developments - subdivisions, malls, hospitals - typically cannot rely on septic tanks alone and instead require a licensed sewage treatment plant (STP) with a discharge permit from the Department of Environment and Natural Resources (DENR) under the Philippine Clean Water Act (RA 9275).
Coordination Points for the Architect
Three habits separate a plumbing-friendly floor plan from a costly one:
Wet-wall stacking - stack toilets, kitchens, and utility rooms vertically, floor after floor, so soil and vent stacks run straight down without offsets that cost money and reduce flow capacity.
Dedicated pipe chases - provide a continuous vertical shaft (not just a thickened wall) for stacks, sized for the largest pipe plus insulation and future access, typically with removable access panels per floor.
Floor-to-floor slope budget - every meter of horizontal drain run consumes centimeters of ceiling height at minimum code slope; long horizontal runs before reaching a vertical stack can force a dropped ceiling or raised floor that changes headroom for the floor below.
Getting these three right during schematic design, not after, is what the ALE is really testing when it asks about plumbing "coordination" rather than plumbing "design."