Study guide
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products
Key Takeaways Explain This Topic AI
A 400 × 200 mm concrete hollow block face covers 0.08 m², so a wall needs 12.5 blocks per square meter before waste.
The mass of a deformed bar in kg/m is about d²/162 with d in millimeters; a 16 mm bar weighs about 1.58 kg/m.
Adding water to fresh concrete at the site raises the water-cement ratio and lowers strength, so slump should be adjusted with admixtures instead.
Concrete should be placed in layers and consolidated with internal vibrators to remove entrapped air without causing segregation.
One board foot is a volume of 1 in × 12 in × 12 in, the unit used to price lumber in Philippine practice.
Last updated: October 2026
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products
The AMSTHC TOS lists five one-item competencies under "Materials for Construction":
Review concrete materials and accessories, formwork, scaffolding and concrete reinforcement.
Estimate concrete masonry, mortar and grout, and masonry design and erection.
Analyze mixing, handling, transporting, placing and consolidating of concrete.
Determine properties of iron and steel, and steel erection and construction.
Specify lumber, plywood, glulam and other panels.
Testing and mix proportioning, which are structural-design TOS items, are in Section 15.5.
Concrete Materials and Accessories
Ingredient Key points
Portland cement ASTM C150 types: I (general), II (moderate sulfate resistance, moderate heat), III (high early strength), IV (low heat), V (high sulfate resistance). Blended cements contain pozzolans or slag. In the Philippines, cement is sold in 40 kg bags.
Fine aggregate Sand passing the 4.75 mm sieve. Its grading is summarized by the fineness modulus (typically 2.3 to 3.1 for concrete sand). It must be clean of silt, clay and organic matter.
Coarse aggregate Gravel or crushed stone. The maximum size is limited by member dimensions and bar spacing.
Water Potable water is generally acceptable. Avoid seawater in reinforced concrete because chlorides corrode steel.
Admixtures (ASTM C494 types A to G) Water-reducing, retarding, accelerating and high-range water-reducing (superplasticizer) types; air-entraining agents are covered separately
Supplementary materials Fly ash, slag cement and silica fume improve durability and workability
Aggregate moisture. Mix designs assume saturated surface-dry (SSD) aggregates. If sand carries 5% free moisture, the batch water is reduced and the sand weight increased by the same amount of water.
Accessories include chairs and bar supports, spacers, tie wire, waterstops, construction-joint keys, inserts and anchor bolts, and curing compounds.
Formwork, Scaffolding and Reinforcement
Formwork must resist the weight of fresh concrete and the lateral pressure (Section 6.2, ACI 347), plus construction live loads. It must also be tight enough to prevent grout loss. Common materials are plywood or phenolic boards on lumber or steel frames, and reusable steel or aluminum systems.
Rule Reason
Strip vertical faces early and soffits late Sides carry only the self-weight of fresh concrete; soffits carry the slab until it gains strength
- Re-shore after stripping Upper floors are cast on young slabs below
- Apply form release agent Prevents bonding and surface damage
- Check line, level and plumb before casting Corrections after the pour are costly
Scaffolding must have firm base plates and sole boards, diagonal bracing and ties to the structure, full decking with toe boards, and guardrails. It should be erected by trained workers and inspected before use (see Section 6.3).
Reinforcement. Deformed bars to PNS 49 or ASTM A615 are specified by diameter (10, 12, 16, 20, 25, 28, 32 and 36 mm) and grade. The approximate mass per meter is:
mass (kg/m) ≈ d 2 162 ( d in mm ) \text{mass (kg/m)} \approx \frac{d^2}{162} \qquad (d \text{ in mm}) mass (kg/m) ≈ 162 d 2 ( d in mm )
- Bar diameter 10 mm 12 mm 16 mm 20 mm 25 mm
- Mass (kg/m) 0.617 0.888 1.58 2.47 3.85
Bars are tied with No. 16 GI tie wire , supported on chairs to keep the specified cover, and lapped or mechanically spliced as the design requires.
Concrete Masonry, Mortar and Grout
Concrete hollow blocks (CHB) in the Philippines are commonly 400 × 200 mm 400 \times 200\text{ mm} 400 × 200 mm in face size, in 100, 150 and 200 mm thicknesses.
Number of blocks. Each block plus its joint covers about 0.40 × 0.20 = 0.08 m 2 0.40 \times 0.20 = 0.08\text{ m}^2 0.40 × 0.20 = 0.08 m 2 , so:
CHB per m 2 = 1 0.08 = 12.5 \text{CHB per m}^2 = \frac{1}{0.08} = 12.5 CHB per m 2 = 0.08 1 = 12.5
Example. A wall 8.0 m 8.0\text{ m} 8.0 m long and 3.0 m 3.0\text{ m} 3.0 m high has a 1.0 × 1.2 m 1.0 \times 1.2\text{ m} 1.0 × 1.2 m window.
Net area: 24.0 − 1.2 = 22.8 m 2 24.0 - 1.2 = 22.8\text{ m}^2 24.0 − 1.2 = 22.8 m 2 .
Blocks: 22.8 × 12.5 = 285 22.8 \times 12.5 = 285 22.8 × 12.5 = 285 , plus 5% breakage, about 300 blocks .
Mortar and grout.
Mortar bonds the blocks; it is typically a cement-sand mix such as 1:3 or 1:4 by volume.
Grout fills the cells containing reinforcement; it is a fluid cement-sand-fine-gravel mix.
Plaster finishes the faces.
Quantities are estimated by volume, from joint thickness, cell volume, the fraction of cells grouted and plaster thickness, then converted to cement bags and cubic meters of sand. Estimators often use tabulated factors per square meter for each CHB size.
Masonry erection rules:
Lay blocks in running bond on a level mortar bed.
Keep vertical reinforcement aligned in grouted cells.
Place horizontal joint reinforcement or bond-beam bars at the specified spacing.
Limit the daily lift height so lower courses are not crushed or displaced.
Mixing, Handling, Transporting, Placing and Consolidating Concrete
- Stage Good practice Defect if ignored
- Mixing Machine-mix until uniform; batch by mass for structural concrete Weak, variable concrete
Transporting Use transit mixers or buckets; avoid long free-flowing chutes; place before initial set Segregation, cold joints
Placing Place in horizontal layers about 300 to 500 mm thick; limit free fall (tremie or elephant trunk for deep forms); work from the corners; place under water only by tremie Honeycombing, rock pockets, segregation
Consolidating Insert internal vibrators vertically at close spacing so their zones overlap; penetrate the previous layer slightly; withdraw slowly Voids, or segregation from over-vibration
Curing Keep moist for at least 7 days with ponding, wet burlap or curing compound; protect from sun and wind Plastic shrinkage cracking, low strength
Joints Place construction joints where shear is low, as shown on drawings; clean and roughen before resuming Weak planes, leaks
Warning
Retempering with water. Adding water at the site to restore slump raises the water-cement ratio and permanently lowers strength. Use a superplasticizer, or reject the load if it is past its time limit.
Iron and Steel: Properties and Erection
- Material Carbon content and character
- Cast iron Over about 2% carbon; brittle, strong in compression
- Wrought iron Very low carbon; ductile; historic structures
- Carbon structural steel About 0.15% to 0.30% carbon; ductile, weldable
- High-strength low-alloy steel Small alloy additions for higher yield strength
Structural steel properties.
Modulus of elasticity about 200 GPa 200\text{ GPa} 200 GPa , density about 7,850 kg/m 3 7{,}850\text{ kg/m}^3 7 , 850 kg/m 3 , and thermal coefficient about 12 × 10 − 6 / ∘ C 12 \times 10^{-6}/^\circ\text{C} 12 × 1 0 − 6 / ∘ C .
Typical grades include ASTM A36 ( F y = 248 MPa F_y = 248\text{ MPa} F y = 248 MPa ) and A572 Grade 50 ( F y = 345 MPa F_y = 345\text{ MPa} F y = 345 MPa ).
Steel loses strength rapidly above about 400 °C, so fire protection is needed.
Steel erection sequence:
Check anchor-bolt positions and base-plate elevations, and grout under the base plates.
Erect columns, then beams.
Provide temporary bracing and guys until floors and permanent bracing are complete.
Plumb and align the frame before final bolting or welding.
Tighten high-strength bolts by an approved method: turn-of-nut, calibrated wrench, or tension-control bolts.
Use qualified welders and procedures, and inspect welds visually and, where specified, by nondestructive testing.
Apply primer and corrosion protection, and touch up after erection.
Lumber, Plywood, Glulam and Panels
Lumber is graded visually or by machine. It is measured in board feet (1 bd ft = 1 in × 12 in × 12 in). A piece measuring 2 in × 4 in × 10 ft contains ( 2 × 4 × 10 ) / 12 = 6.67 (2 \times 4 \times 10)/12 = 6.67 ( 2 × 4 × 10 ) /12 = 6.67 board feet.
Lumber should be seasoned (kiln- or air-dried) for framing to limit shrinkage and warping, and treated against termites and decay where exposed.
Plywood is made of cross-laminated veneers, which gives dimensional stability and resistance to splitting. Marine or exterior grades use waterproof glue. Phenolic-faced plywood is used for repeated formwork.
Glued-laminated timber (glulam) is made by bonding graded lumber laminations into large straight or curved members. It allows long spans and makes efficient use of smaller pieces.
Other panels include oriented strand board, fiber-cement board and gypsum board for walls and ceilings, and particleboard for interiors.
Specify the species or strength group, grade, moisture condition, dimensions (nominal or dressed), treatment and fire rating where required.