Study guide

2.3 Differential and Integral Calculus

PRC Civil Engineer Licensure Examination CELE

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Examination Overview, RA 544 & Professional Practice

1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice

2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics

2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum

3 Chapter 3: Engineering Data Analysis & Engineering Economy

3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis

4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying

4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves

5 Chapter 5: Highway & Transportation Engineering

5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems

6 Chapter 6: Construction Materials, Methods, Management & Safety

6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical

7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy

7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses

8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply

8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment

9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass

9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement

10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations

10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability

11 Chapter 11: Engineering Mechanics & Statics

11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members

12 Chapter 12: Strength of Materials

12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle

13 Chapter 13: Structural Analysis & NSCP Load Criteria

13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake

14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)

14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design

15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing

15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning

2.3 Differential and Integral Calculus

Key Takeaways Explain This Topic AI

Critical points occur where f'(x) = 0 or is undefined; the Second Derivative Test establishes local maxima (f'' < 0), local minima (f'' > 0), and potential points of inflection (f'' = 0).

Related rates problems differentiate geometric constraints with respect to time using the chain rule, requiring consistent rate signs for filling versus draining.

Analytical integration techniques—including u-substitution, integration by parts (LIATE rule), and partial fractions—resolve structural shear, moment, and fluid pressure integrals.

Volumes of revolution are computed via disk, washer, or cylindrical shell formulations, while Pappus's Second Theorem equates volume to planar area multiplied by centroid path length (V = 2π r̄ A).

Last updated: October 2026

2.3 Differential and Integral Calculus

Differential and integral calculus provides the essential mathematical engine for civil engineering design, governing beam deflections, fluid kinematics, geotechnical settlement rates, and structural cross-sectional properties. In the CELE examination, calculus problems require rapid differentiation, applied optimization, multi-variable related rates, integration techniques, and the calculation of plane areas, volumes of revolution, and centroids.

  • Limits, Continuity & L'Hôpital's Rule
  • Indeterminate Forms

When evaluating the limit lim ⁡ x → c f ( x ) g ( x ) \lim_{x \to c} \frac{f(x)}{g(x)} lim x → c ​ g ( x ) f ( x ) ​ yields indeterminate ratios of type [ 0 0 ] \left[\frac{0}{0}\right] [ 0 0 ​ ] or [ ∞ ∞ ] \left[\frac{\infty}{\infty}\right] [ ∞ ∞ ​ ] , L'Hôpital's Rule establishes that: lim ⁡ x → c f ( x ) g ( x ) = lim ⁡ x → c f ′ ( x ) g ′ ( x ) \lim_{x \to c} \frac{f(x)}{g(x)} = \lim_{x \to c} \frac{f'(x)}{g'(x)} lim x → c ​ g ( x ) f ( x ) ​ = lim x → c ​ g ′ ( x ) f ′ ( x ) ​ Provided the derivatives exist and the resulting limit converges or diverges to infinity. (Caution: Do not apply the quotient rule when using L'Hôpital's Rule; differentiate the numerator and denominator independently!)

Standard Fundamental Limits

lim ⁡ x → 0 sin ⁡ x x = 1 ( x in radians ) \lim_{x \to 0} \frac{\sin x}{x} = 1 \quad (x \text{ in radians}) lim x → 0 ​ x s i n x ​ = 1 ( x in radians )

lim ⁡ x → 0 1 − cos ⁡ x x = 0 \lim_{x \to 0} \frac{1 - \cos x}{x} = 0 lim x → 0 ​ x 1 − c o s x ​ = 0

lim ⁡ x → ∞ ( 1 + 1 x ) x = e ≈ 2.71828 \lim_{x \to \infty} \left(1 + \frac{1}{x}\right)^x = e \approx 2.71828 lim x → ∞ ​ ( 1 + x 1 ​ ) x = e ≈ 2.71828

  • Differential Calculus & Optimization
  • Core Differentiation Rules

Product Rule: d d x [ u v ] = u d v d x + v d u d x \frac{d}{dx}[uv] = u\frac{dv}{dx} + v\frac{du}{dx} d x d ​ [ uv ] = u d x d v ​ + v d x d u ​

Quotient Rule: d d x [ u v ] = v d u d x − u d v d x v 2 \frac{d}{dx}\left[\frac{u}{v}\right] = \frac{v\frac{du}{dx} - u\frac{dv}{dx}}{v^2} d x d ​ [ v u ​ ] = v 2 v d x d u ​ − u d x d v ​ ​

Chain Rule: d y d x = d y d u ⋅ d u d x \frac{dy}{dx} = \frac{dy}{du} \cdot \frac{du}{dx} d x d y ​ = d u d y ​ ⋅ d x d u ​

Transcendental Derivatives: d d x ( sin ⁡ u ) = cos ⁡ u d u d x , d d x ( cos ⁡ u ) = − sin ⁡ u d u d x , d d x ( tan ⁡ u ) = sec ⁡ 2 u d u d x \frac{d}{dx}(\sin u) = \cos u \frac{du}{dx}, \quad \frac{d}{dx}(\cos u) = -\sin u \frac{du}{dx}, \quad \frac{d}{dx}(\tan u) = \sec^2 u \frac{du}{dx} d x d ​ ( sin u ) = cos u d x d u ​ , d x d ​ ( cos u ) = − sin u d x d u ​ , d x d ​ ( tan u ) = sec 2 u d x d u ​ d d x ( e u ) = e u d u d x , d d x ( ln ⁡ u ) = 1 u d u d x , d d x ( arctan ⁡ u ) = 1 1 + u 2 d u d x \frac{d}{dx}(e^u) = e^u \frac{du}{dx}, \quad \frac{d}{dx}(\ln u) = \frac{1}{u}\frac{du}{dx}, \quad \frac{d}{dx}(\arctan u) = \frac{1}{1 + u^2}\frac{du}{dx} d x d ​ ( e u ) = e u d x d u ​ , d x d ​ ( ln u ) = u 1 ​ d x d u ​ , d x d ​ ( arctan u ) = 1 + u 2 1 ​ d x d u ​

Critical Points & Extrema Classification

A critical point of a differentiable function y = f ( x ) y = f(x) y = f ( x ) occurs where f ′ ( x ) = 0 f'(x) = 0 f ′ ( x ) = 0 or where f ′ ( x ) f'(x) f ′ ( x ) is undefined:

First Derivative Test:

  • f ′ ( x ) f'(x) f ′ ( x ) changes from positive to negative at x = c ⟹ x = c \implies x = c ⟹ Local Maximum
  • f ′ ( x ) f'(x) f ′ ( x ) changes from negative to positive at x = c ⟹ x = c \implies x = c ⟹ Local Minimum
  • f ′ ( x ) f'(x) f ′ ( x ) maintains the same sign ⟹ \implies ⟹ Horizontal Inflection Point

Second Derivative Test:

If f ′ ( c ) = 0 f'(c) = 0 f ′ ( c ) = 0 and f ′ ′ ( c ) < 0 ⟹ f''(c) < 0 \implies f ′′ ( c ) < 0 ⟹ Local Maximum (curve is concave downward)

If f ′ ( c ) = 0 f'(c) = 0 f ′ ( c ) = 0 and f ′ ′ ( c ) > 0 ⟹ f''(c) > 0 \implies f ′′ ( c ) > 0 ⟹ Local Minimum (curve is concave upward)

If f ′ ( c ) = 0 f'(c) = 0 f ′ ( c ) = 0 and f ′ ′ ( c ) = 0 ⟹ f''(c) = 0 \implies f ′′ ( c ) = 0 ⟹ Test is inconclusive; use First Derivative Test.

Point of Inflection: A point where the concavity changes sign. A necessary condition for an inflection point is f ′ ′ ( x ) = 0 f''(x) = 0 f ′′ ( x ) = 0 or undefined, with a proven sign change of f ′ ′ ( x ) f''(x) f ′′ ( x ) across the point.

Related Rates in Civil Engineering

Related rates problems model physical systems where multiple interconnected geometric parameters change dynamically over time t t t . The time derivatives are linked via implicit differentiation using the chain rule.

Systematic 4-Step Solution Method

Geometric Sketch & Parameter Identification: Assign variable symbols to all dynamic quantities and identify constants.

Formulate Constraint Equation: Write a single geometric, trigonometric, or volumetric equation relating the variables (e.g., Pythagorean theorem, similar triangles, volume formula).

Implicit Differentiation: Differentiate the entire equation with respect to time t t t ( d d t \frac{d}{dt} d t d ​ ).

Substitution of Instantaneous Values: Substitute known numerical values and given rates only after differentiation to solve for the target rate.

Standard CELE Related Rates Scenarios

Conical Tank Draining: Water draining from an inverted right circular cone of fixed height H H H and base radius R R R :

By similar triangles: r h = R H ⟹ r = ( R H ) h \frac{r}{h} = \frac{R}{H} \implies r = \left(\frac{R}{H}\right)h h r ​ = H R ​ ⟹ r = ( H R ​ ) h

Volume: V = 1 3 π r 2 h = 1 3 π ( R H ) 2 h 3 V = \frac{1}{3}\pi r^2 h = \frac{1}{3}\pi \left(\frac{R}{H}\right)^2 h^3 V = 3 1 ​ π r 2 h = 3 1 ​ π ( H R ​ ) 2 h 3

Differentiation: d V d t = π ( R H ) 2 h 2 d h d t \frac{dV}{dt} = \pi \left(\frac{R}{H}\right)^2 h^2 \frac{dh}{dt} d t d V ​ = π ( H R ​ ) 2 h 2 d t d h ​

Sliding Structural Ladder: A ladder of constant length L L L sliding down a vertical wall:

Constraint: x 2 + y 2 = L 2 x^2 + y^2 = L^2 x 2 + y 2 = L 2

Differentiation: 2 x d x d t + 2 y d y d t = 0 ⟹ d y d t = − x y d x d t 2x\frac{dx}{dt} + 2y\frac{dy}{dt} = 0 \implies \frac{dy}{dt} = -\frac{x}{y}\frac{dx}{dt} 2 x d t d x ​ + 2 y d t d y ​ = 0 ⟹ d t d y ​ = − y x ​ d t d x ​

  • Integral Calculus & Integration Techniques
  • Core Integration Strategies

Integration by Substitution ( u u u -sub): Transforms ∫ f ( g ( x ) ) g ′ ( x ) d x \int f(g(x))g'(x)\,dx ∫ f ( g ( x )) g ′ ( x ) d x into ∫ f ( u ) d u \int f(u)\,du ∫ f ( u ) d u .

Integration by Parts: ∫ u d v = u v − ∫ v d u \int u\,dv = uv - \int v\,du ∫ u d v = uv − ∫ v d u (Follow the LIATE mnemonic to assign u u u : Logarithmic, Inverse trig, Algebraic, Trigonometric, Exponential).

Trigonometric Substitutions:

For a 2 − x 2 \sqrt{a^2 - x^2} a 2 − x 2 ​ : Substitute x = a sin ⁡ θ ⟹ d x = a cos ⁡ θ d θ x = a\sin\theta \implies dx = a\cos\theta\,d\theta x = a sin θ ⟹ d x = a cos θ d θ

For a 2 + x 2 \sqrt{a^2 + x^2} a 2 + x 2 ​ : Substitute x = a tan ⁡ θ ⟹ d x = a sec ⁡ 2 θ d θ x = a\tan\theta \implies dx = a\sec^2\theta\,d\theta x = a tan θ ⟹ d x = a sec 2 θ d θ

For x 2 − a 2 \sqrt{x^2 - a^2} x 2 − a 2 ​ : Substitute x = a sec ⁡ θ ⟹ d x = a sec ⁡ θ tan ⁡ θ d θ x = a\sec\theta \implies dx = a\sec\theta\tan\theta\,d\theta x = a sec θ ⟹ d x = a sec θ tan θ d θ

Partial Fractions Decomposition: Resolves rational functions P ( x ) / Q ( x ) P(x)/Q(x) P ( x ) / Q ( x ) into sums of simpler fractions with linear or irreducible quadratic denominators.

  • Definite Integrals: Areas, Volumes of Revolution & Centroids
  • 1. Area Between Plane Curves

For regions bounded by upper curve y 2 = f ( x ) y_2 = f(x) y 2 ​ = f ( x ) and lower curve y 1 = g ( x ) y_1 = g(x) y 1 ​ = g ( x ) from x = a x = a x = a to x = b x = b x = b : A = ∫ a b [ f ( x ) − g ( x ) ] d x A = \int_a^b [f(x) - g(x)]\,dx A = ∫ a b ​ [ f ( x ) − g ( x )] d x Using horizontal strips bounded by right curve x 2 = f ( y ) x_2 = f(y) x 2 ​ = f ( y ) and left curve x 1 = g ( y ) x_1 = g(y) x 1 ​ = g ( y ) from y = c y = c y = c to y = d y = d y = d : A = ∫ c d [ f ( y ) − g ( y ) ] d y A = \int_c^d [f(y) - g(y)]\,dy A = ∫ c d ​ [ f ( y ) − g ( y )] d y

2. Volumes of Solids of Revolution

Method Orientation of Slices Relative to Axis of Revolution Volume Integral Formula

Disk Method Perpendicular to axis (solid of revolution, no inner void) V = π ∫ a b [ R ( x ) ] 2 d x V = \pi \int_a^b [R(x)]^2\,dx V = π ∫ a b ​ [ R ( x ) ] 2 d x

Washer Method Perpendicular to axis (hollow solid with inner radius r r r and outer radius R R R ) V = π ∫ a b ( [ R ( x ) ] 2 − [ r ( x ) ] 2 ) d x V = \pi \int_a^b ([R(x)]^2 - [r(x)]^2)\,dx V = π ∫ a b ​ ([ R ( x ) ] 2 − [ r ( x ) ] 2 ) d x

Cylindrical Shell Method Parallel to axis of revolution V = 2 π ∫ a b ( radius ) ( height ) d x V = 2\pi \int_a^b (\text{radius})(\text{height})\,dx V = 2 π ∫ a b ​ ( radius ) ( height ) d x

3. Centroids of Plane Areas

The coordinates of the centroid ( x ˉ , y ˉ ) (\bar{x}, \bar{y}) ( x ˉ , y ˉ ​ ) of a planar lamina with area A A A are defined by first moments of area: x ˉ = Q y A = 1 A ∫ x ~ d A , y ˉ = Q x A = 1 A ∫ y ~ d A \bar{x} = \frac{Q_y}{A} = \frac{1}{A} \int \tilde{x}\,dA, \quad \bar{y} = \frac{Q_x}{A} = \frac{1}{A} \int \tilde{y}\,dA x ˉ = A Q y ​ ​ = A 1 ​ ∫ x ~ d A , y ˉ ​ = A Q x ​ ​ = A 1 ​ ∫ y ~ ​ d A

Using vertical strips of width d x dx d x : A = ∫ a b [ y 2 − y 1 ] d x , x ˉ = 1 A ∫ a b x [ y 2 − y 1 ] d x , y ˉ = 1 2 A ∫ a b [ y 2 2 − y 1 2 ] d x A = \int_a^b [y_2 - y_1]\,dx, \quad \bar{x} = \frac{1}{A} \int_a^b x[y_2 - y_1]\,dx, \quad \bar{y} = \frac{1}{2A} \int_a^b [y_2^2 - y_1^2]\,dx A = ∫ a b ​ [ y 2 ​ − y 1 ​ ] d x , x ˉ = A 1 ​ ∫ a b ​ x [ y 2 ​ − y 1 ​ ] d x , y ˉ ​ = 2 A 1 ​ ∫ a b ​ [ y 2 2 ​ − y 1 2 ​ ] d x

4. Theorems of Pappus-Guldinus

Pappus's theorems provide extremely fast shortcuts for volumes and surface areas of revolution:

First Theorem (Surface Area): The surface area generated by rotating a plane curve of length L L L about an external coplanar axis is equal to the curve length multiplied by the distance traveled by its centroid: S = 2 π r ˉ L S = 2\pi \bar{r} L S = 2 π r ˉ L

Second Theorem (Volume): The volume of a solid of revolution generated by rotating a plane area A A A about an external coplanar axis is equal to the area multiplied by the distance traveled by its area centroid: V = 2 π r ˉ A V = 2\pi \bar{r} A V = 2 π r ˉ A

  • Step-by-Step Worked Problems
  • Worked Example: Related Rates in Water Storage Tank

Problem: A municipal elevated conical drainage hopper has a top diameter of 6.0 m 6.0\text{ m} 6.0 m (radius R = 3.0 m R = 3.0\text{ m} R = 3.0 m ) and a total height H = 9.0 m H = 9.0\text{ m} H = 9.0 m . Water is pumped into the hopper at a constant rate of 1.80 m 3 / min 1.80\text{ m}^3/\text{min} 1.80 m 3 / min , while simultaneously draining out of the bottom orifice at a rate of 0.60 m 3 / min 0.60\text{ m}^3/\text{min} 0.60 m 3 / min . At what exact rate is the water surface rising when the instantaneous water depth in the hopper is 4.5 m 4.5\text{ m} 4.5 m ?

Solution:

Net rate of volumetric accumulation: d V d t = Q in − Q out = 1.80 − 0.60 = + 1.20 m 3 / min \frac{dV}{dt} = Q_{\text{in}} - Q_{\text{out}} = 1.80 - 0.60 = +1.20\text{ m}^3/\text{min} d t d V ​ = Q in ​ − Q out ​ = 1.80 − 0.60 = + 1.20 m 3 / min

Geometric relationship via similar triangles: r h = R H = 3.0 9.0 = 1 3 ⟹ r = h 3 \frac{r}{h} = \frac{R}{H} = \frac{3.0}{9.0} = \frac{1}{3} \implies r = \frac{h}{3} h r ​ = H R ​ = 9.0 3.0 ​ = 3 1 ​ ⟹ r = 3 h ​

Express volume solely as a function of depth h h h : V = 1 3 π r 2 h = 1 3 π ( h 3 ) 2 h = π 27 h 3 V = \frac{1}{3}\pi r^2 h = \frac{1}{3}\pi \left(\frac{h}{3}\right)^2 h = \frac{\pi}{27} h^3 V = 3 1 ​ π r 2 h = 3 1 ​ π ( 3 h ​ ) 2 h = 27 π ​ h 3

Differentiate implicitly with respect to time t t t : d V d t = π 27 ⋅ 3 h 2 d h d t = π h 2 9 d h d t \frac{dV}{dt} = \frac{\pi}{27} \cdot 3h^2 \frac{dh}{dt} = \frac{\pi h^2}{9} \frac{dh}{dt} d t d V ​ = 27 π ​ ⋅ 3 h 2 d t d h ​ = 9 π h 2 ​ d t d h ​

Substitute known parameters ( h = 4.5 m h = 4.5\text{ m} h = 4.5 m and d V d t = 1.20 m 3 / min \frac{dV}{dt} = 1.20\text{ m}^3/\text{min} d t d V ​ = 1.20 m 3 / min ): 1.20 = π ( 4.5 ) 2 9 d h d t = π ( 20.25 ) 9 d h d t = 2.25 π d h d t 1.20 = \frac{\pi (4.5)^2}{9} \frac{dh}{dt} = \frac{\pi (20.25)}{9} \frac{dh}{dt} = 2.25\pi \frac{dh}{dt} 1.20 = 9 π ( 4.5 ) 2 ​ d t d h ​ = 9 π ( 20.25 ) ​ d t d h ​ = 2.25 π d t d h ​ d h d t = 1.20 2.25 π = 1.20 7.06858 ≈ 0.1698 m/min ≈ 0.170 m/min \frac{dh}{dt} = \frac{1.20}{2.25\pi} = \frac{1.20}{7.06858} \approx 0.1698\text{ m/min} \approx 0.170\text{ m/min} d t d h ​ = 2.25 π 1.20 ​ = 7.06858 1.20 ​ ≈ 0.1698 m/min ≈ 0.170 m/min

The water surface is rising at a rate of 0.170 m/min 0.170\text{ m/min} 0.170 m/min ( 17.0 cm/min 17.0\text{ cm/min} 17.0 cm/min ).

CELE Board Exam Traps & Strategic Checklists

Warning

Premature Constant Substitution in Related Rates: Never substitute the numerical instantaneous depth or distance into the geometric relation before differentiating. Constants that remain invariant throughout the motion (e.g., tank radius, ladder length) may be substituted early, but dynamic variables must remain in algebraic form until after differentiation.

Washer vs. Shell Integration Limits: When revolving around the y y y -axis:

The Washer Method uses horizontal slices with integration limits along the y y y -axis ( d y dy d y ).

The Shell Method uses vertical slices with integration limits along the x x x -axis ( d x dx d x ).

Mixing slice orientation with incorrect differentials is the most frequent calculus error on the board exam.

Loading diagram... Decision Tree for Volumes of Solids of Revolution