Study guide
11.3 Cables, Trusses, and Internal Forces in Members
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
11.3 Cables, Trusses, and Internal Forces in Members
Key Takeaways Explain This Topic AI
Ideal trusses assume frictionless pin connections with loads applied exclusively at joints, meaning every member acts as a purely axial two-force member carrying tension or compression.
A coplanar truss is statically determinate and internally stable when m + r = 2j; if m + r > 2j it is statically indeterminate, and if m + r < 2j it forms an unstable kinematic mechanism.
Zero-force members can be identified by inspection: if two non-collinear members meet at an unloaded joint, both carry zero force; if three members meet with two collinear, the third is zero.
Flexible cables carrying loads uniformly distributed across the horizontal span form parabolas (y = w x² / (2 T0)); cables carrying their own uniform dead weight along their arc form catenaries (y = c cosh(x/c)).
Frames and machines contain at least one multi-force member subjected to three or more force locations or bending actions, requiring individual component dismantling and Newton's Third Law to solve internal pin reactions.
Last updated: October 2026
11.3 Cables, Trusses, and Internal Forces in Members
Civil engineering systems rely on skeletal structural frameworks and tensile elements to span significant distances efficiently. Trusses, cables, and frames are core topics on the PRC Civil Engineering Licensure Examination (CELE). Understanding how applied loads translate into internal axial thrusts, cable tensions, and multi-force frame reactions is essential for structural analysis, bridge design, and temporary falsework engineering.
Planar Trusses and Ideal Truss Assumptions
A truss is a structural framework composed of slender members joined together at their ends to form a rigid assembly of triangles. The classical ideal truss assumptions are:
Frictionless Pin Connections: All members are connected at their ends by smooth, frictionless spherical or cylindrical pins.
Joint Loading Only: All external design loads and support reactions are applied exclusively at the panel joints (pin nodes).
Centroidal Concurrency: The centroidal axes of all framing members at any given joint intersect at a single concurrent point.
Weightless Members: The self-weight of members is negligible compared to live and dead service loads (or half of each member's weight is allocated to its two end nodes).
Under these ideal assumptions, bending moments and transverse shear forces are identically zero . Every member behaves as a two-force member , carrying purely axial forces: tension ( T > 0 T > 0 T > 0 ) pulling away from the joint, or compression ( C < 0 C < 0 C < 0 ) pushing toward the joint.
Classification of Coplanar Trusses
A planar truss containing m m m members, j j j joints, and supported by r r r independent external reaction components is classified by comparing total unknowns to equilibrium equations:
Total Unknowns = m + r , Total Equations = 2 j \text{Total Unknowns} = m + r, \qquad \text{Total Equations} = 2j Total Unknowns = m + r , Total Equations = 2 j
Mathematical Criterion Classification Structural Behavior
m + r < 2 j m + r < 2j m + r < 2 j Statically Unstable (Mechanism) Insufficient members or reactions; collapses under general loading
m + r = 2 j m + r = 2j m + r = 2 j Statically Determinate Stable and solvable purely using equations of statics (if properly arranged)
m + r > 2 j m + r > 2j m + r > 2 j Statically Indeterminate Contains redundant members or supports; degree of indeterminacy i = ( m + r ) − 2 j i = (m + r) - 2j i = ( m + r ) − 2 j
For a standard simple planar truss with three external determinate reactions ( r = 3 r = 3 r = 3 ), the internal determinacy criterion simplifies to: m = 2 j − 3 m = 2j - 3 m = 2 j − 3
Stability Traps
Satisfying m + r = 2 j m + r = 2j m + r = 2 j is a necessary but not sufficient condition for stability:
External Instability: Occurs if support reactions are all parallel or concurrent.
Internal Instability: Occurs if members are arranged improperly (e.g., forming an unbraced four-bar rectangular mechanism in one panel while over-stiffening another panel).
Visual Identification of Zero-Force Members
Identifying zero-force members by inspection prior to calculation dramatically reduces arithmetic and prevents algebraic errors on board exams.
Case 1: Two Non-Collinear Members at an Unloaded Joint
If only two non-collinear members meet at a joint and no external load or reaction acts at that joint, both members are zero-force members . ∑ F y ′ = 0 ⟹ F 1 sin θ = 0 ⟹ F 1 = 0 \sum F_y' = 0 \implies F_1 \sin \theta = 0 \implies F_1 = 0 ∑ F y ′ = 0 ⟹ F 1 sin θ = 0 ⟹ F 1 = 0 ∑ F x ′ = 0 ⟹ F 2 = 0 \sum F_x' = 0 \implies F_2 = 0 ∑ F x ′ = 0 ⟹ F 2 = 0 Member 1
- /
- / θ
- (Joint A)-------- Member 2 ===> F_1 = 0 and F_2 = 0
- (No load)
- Case 2: Three Members (Two Collinear) at an Unloaded Joint
If three members meet at a joint with no external load or reaction , and two of the members are collinear, the non-collinear third member is a zero-force member , and the two collinear members carry equal forces. ∑ F y = 0 ⟹ F 3 = 0 , ∑ F x = 0 ⟹ F 1 = F 2 \sum F_y = 0 \implies F_3 = 0, \qquad \sum F_x = 0 \implies F_1 = F_2 ∑ F y = 0 ⟹ F 3 = 0 , ∑ F x = 0 ⟹ F 1 = F 2 Member 3 (F3 = 0)
- |
- v
- Member 1 ---- (Joint B) ---- Member 2 ===> F_3 = 0, F_1 = F_2
- (No load)
- Case 3: Two Non-Collinear Members with Collinear Applied Load
If two non-collinear members meet at a joint subjected to an external load P P P that is collinear with one of the members , the other member carries zero force ( F 2 = 0 F_2 = 0 F 2 = 0 ), and the collinear member balances the load ( F 1 = P F_1 = P F 1 = P ).
Methods of Truss Analysis
Analysis Method Analytical Scope Mathematical Procedure Ideal Application
Method of Joints Solves for all member forces across the entire truss Isolate individual pin joints; apply 2 scalar equations: ∑ F x = 0 , ∑ F y = 0 \sum F_x = 0, \sum F_y = 0 ∑ F x = 0 , ∑ F y = 0 Complete truss analysis; computing joint deflections (virtual work)
Method of Sections Solves for specific interior members directly Pass an imaginary cutting section through max 3 unknown members; apply 3 coplanar equations: ∑ F x = 0 , ∑ F y = 0 , ∑ M O = 0 \sum F_x = 0, \sum F_y = 0, \sum M_O = 0 ∑ F x = 0 , ∑ F y = 0 , ∑ M O = 0 Fast determination of forces in critical chords, diagonals, or center panels
Tip
Strategic Section Cutting: When using the Method of Sections, choose the moment center O O O at the intersection point of two unknown cut members. The moment equation ∑ M O = 0 \sum M_O = 0 ∑ M O = 0 will immediately solve for the third member force in a single algebraic step without simultaneous equations.
Flexible Suspension Cables
Cables are lightweight, flexible structural elements designed to span long distances in suspension bridges, transmission lines, and guyed masts. The classical flexible cable assumptions dictate:
Cables have zero flexural rigidity (zero bending stiffness: M = 0 M = 0 M = 0 ) and cannot resist transverse shear ( V = 0 V = 0 V = 0 ).
Cables are in pure, continuous tension directed tangentially along the cable curve.
Cables Carrying Uniform Horizontal Loads (Parabolic Cables)
When a suspension bridge deck transmits a uniformly distributed gravity load w w w per unit of horizontal span length (e.g., in kN/m \text{kN/m} kN/m along the x x x -axis): y ^ w (kN/m horizontal)
- | vvvvvvvvvvvvvvvvvvv
- Support A Vertex (T0) Support B
- \ * /
- \_ _/' \_ _/
- \___________/' '\___________/
- | <------- L/2 -------> | <------ L/2 ------> |
Taking the lowest point (vertex) as the coordinate origin ( 0 , 0 ) (0, 0) ( 0 , 0 ) where the cable slope is horizontal:
Minimum Tension ( T 0 T_0 T 0 ): Occurs at the vertex ( x = 0 x = 0 x = 0 ) and acts purely horizontal.
Governing Differential Equation: d y d x = w x T 0 ⟹ y = w x 2 2 T 0 \frac{dy}{dx} = \frac{w x}{T_0} \implies y = \frac{w x^2}{2 T_0} d x d y = T 0 w x ⟹ y = 2 T 0 w x 2 The cable assumes a parabolic geometry .
For a symmetric cable of total horizontal span L L L and maximum central sag h h h at midspan ( x = L / 2 , y = h x = L/2, y = h x = L /2 , y = h ): h = w ( L / 2 ) 2 2 T 0 = w L 2 8 T 0 ⟹ T 0 = w L 2 8 h h = \frac{w (L/2)^2}{2 T_0} = \frac{w L^2}{8 T_0} \implies T_0 = \frac{w L^2}{8 h} h = 2 T 0 w ( L /2 ) 2 = 8 T 0 w L 2 ⟹ T 0 = 8 h w L 2
Tension at Any Distance x x x : T = T 0 2 + ( w x ) 2 = T 0 1 + ( w x T 0 ) 2 = T 0 1 + ( 2 y x ) 2 T = \sqrt{T_0^2 + (w x)^2} = T_0 \sqrt{1 + \left( \frac{w x}{T_0} \right)^2} = T_0 \sqrt{1 + \left( \frac{2y}{x} \right)^2} T = T 0 2 + ( w x ) 2 = T 0 1 + ( T 0 w x ) 2 = T 0 1 + ( x 2 y ) 2
Maximum Tension ( T max T_{\max} T m a x ): Occurs at the tower supports ( x = ± L / 2 x = \pm L/2 x = ± L /2 ): T max = T 0 2 + ( w L 2 ) 2 = T 0 1 + ( 4 h L ) 2 T_{\max} = \sqrt{T_0^2 + \left( \frac{w L}{2} \right)^2} = T_0 \sqrt{1 + \left( \frac{4h}{L} \right)^2} T m a x = T 0 2 + ( 2 w L ) 2 = T 0 1 + ( L 4 h ) 2
Cable Arc Length ( S S S ): Evaluated by series expansion for practical flat sags ( h / L ≤ 0.1 h/L \le 0.1 h / L ≤ 0.1 ): S = ∫ − L / 2 L / 2 1 + ( d y d x ) 2 d x ≈ L ( 1 + 8 3 ( h L ) 2 − 32 5 ( h L ) 4 + … ) ≈ L + 8 h 2 3 L S = \int_{-L/2}^{L/2} \sqrt{1 + \left( \frac{dy}{dx} \right)^2} dx \approx L \left( 1 + \frac{8}{3} \left( \frac{h}{L} \right)^2 - \frac{32}{5} \left( \frac{h}{L} \right)^4 + \dots \right) \approx L + \frac{8 h^2}{3 L} S = ∫ − L /2 L /2 1 + ( d x d y ) 2 d x ≈ L ( 1 + 3 8 ( L h ) 2 − 5 32 ( L h ) 4 + … ) ≈ L + 3 L 8 h 2
Cables Carrying Uniform Self-Weight (Catenary Cables)
When a heavy cable (such as an electrical transmission conductor) hangs freely under its own uniform weight w w w per unit of arc length (along s s s ):
Governing Equation: y = c cosh ( x c ) − c ( where c = T 0 w ) y = c \cosh\left( \frac{x}{c} \right) - c \qquad \left( \text{where } c = \frac{T_0}{w} \right) y = c cosh ( c x ) − c ( where c = w T 0 )
Fundamental Catenary Relations: s = c sinh ( x c ) , y 2 + 2 c y = s 2 s = c \sinh\left( \frac{x}{c} \right), \qquad y^2 + 2 c y = s^2 s = c sinh ( c x ) , y 2 + 2 cy = s 2 If the vertical axis origin is shifted down by distance c c c ( y ′ = y + c = c cosh ( x / c ) y' = y + c = c \cosh(x/c) y ′ = y + c = c cosh ( x / c ) ): T = w y ′ = w ( y + c ) = T 0 + w y T = w y' = w (y + c) = T_0 + w y T = w y ′ = w ( y + c ) = T 0 + w y The tension at any elevation equals the horizontal tension T 0 T_0 T 0 plus the weight of a vertical column of cable extending to that point!
Frames and Machines: Multi-Force Members
Unlike ideal trusses, frames and machines are structural assemblies that contain at least one multi-force member (a member acted upon by forces at three or more points, or carrying distributed loads/applied couples).
Frames: Rigid, stationary structures designed to support external service loads.
Machines: Structures designed to transmit or modify input forces (contain moving components).
Analysis Strategy for Frames
External Equilibrium: Treat the entire assembly as a single rigid body to find external reactions (if determinate).
Dismantle the Assembly: Disassemble the frame into individual member free-body diagrams.
Apply Newton's Third Law: At every internal connecting pin, the reactive forces exerted between members are equal in magnitude and opposite in direction ( B x 1 = − B x 2 , B y 1 = − B y 2 B_{x1} = -B_{x2}, B_{y1} = -B_{y2} B x 1 = − B x 2 , B y 1 = − B y 2 ).
Apply Equations of Statics: Solve ∑ F x = 0 , ∑ F y = 0 , ∑ M = 0 \sum F_x = 0, \sum F_y = 0, \sum M = 0 ∑ F x = 0 , ∑ F y = 0 , ∑ M = 0 for each individual member.
- Step-by-Step Worked Problem Examples
- Worked Example 1: Method of Sections for a Bridge Truss
Problem: A simply supported Warren bridge truss spans L = 18.0 m L = 18.0\text{ m} L = 18.0 m , consisting of six panels of 3.0 m 3.0\text{ m} 3.0 m each with a constant truss height h = 4.0 m h = 4.0\text{ m} h = 4.0 m . Vertical downward loads of P = 60.0 kN P = 60.0\text{ kN} P = 60.0 kN act at panel joints L 1 , L 2 , L 3 , L 4 , L 5 L_1, L_2, L_3, L_4, L_5 L 1 , L 2 , L 3 , L 4 , L 5 . The vertical reactions at supports L 0 L_0 L 0 and L 6 L_6 L 6 are each R = 150.0 kN ↑ R = 150.0\text{ kN} \uparrow R = 150.0 kN ↑ .
- Determine the axial force in the top chord member U 2 U 3 U_2 U_3 U 2 U 3 . U1 U2 U3 U4 U5
- *--------*--------*--------*--------*
- / \ / \ / \ / \ / \
- / \ / \ / \ / \ / \
- *-----*--*-----*--*-----*--*-----*--*-----*
- L0 L1 L2 L3 L4 L5 L6
- ^ (60kN) (60kN) (60kN) (60kN) (60kN) ^
- 150 kN 150 kN
Solution:
Step 1: Pass an Imaginary Cutting Section Pass a vertical cutting plane through top chord U 2 U 3 U_2 U_3 U 2 U 3 , diagonal U 2 L 3 U_2 L_3 U 2 L 3 , and bottom chord L 2 L 3 L_2 L_3 L 2 L 3 . Isolate the left portion of the truss ( L 0 L_0 L 0 to section cut).
Step 2: Identify External Forces on Left Portion
Upward reaction at L 0 L_0 L 0 : R = 150.0 kN ↑ R = 150.0\text{ kN} \uparrow R = 150.0 kN ↑ at x = 0 m x = 0\text{ m} x = 0 m .
Downward panel load at L 1 L_1 L 1 : P 1 = 60.0 kN ↓ P_1 = 60.0\text{ kN} \downarrow P 1 = 60.0 kN ↓ at x = 3.0 m x = 3.0\text{ m} x = 3.0 m .
Downward panel load at L 2 L_2 L 2 : P 2 = 60.0 kN ↓ P_2 = 60.0\text{ kN} \downarrow P 2 = 60.0 kN ↓ at x = 6.0 m x = 6.0\text{ m} x = 6.0 m .
Cut member forces: F U 2 U 3 F_{U2U3} F U 2 U 3 (top chord), F U 2 L 3 F_{U2L3} F U 2 L 3 (diagonal), F L 2 L 3 F_{L2L3} F L 2 L 3 (bottom chord).
Step 3: Choose Strategic Moment Center Notice that cut diagonal F U 2 L 3 F_{U2L3} F U 2 L 3 and cut bottom chord F L 2 L 3 F_{L2L3} F L 2 L 3 both pass through joint L 3 L_3 L 3 ( x = 9.0 m , y = 0 m x = 9.0\text{ m}, y = 0\text{ m} x = 9.0 m , y = 0 m ). Taking moments about joint L 3 L_3 L 3 eliminates both forces completely!
Step 4: Formulate and Solve Moment Equilibrium Assume F U 2 U 3 F_{U2U3} F U 2 U 3 is in tension (pulling to the right along y = 4.0 m y = 4.0\text{ m} y = 4.0 m ): ∑ M L 3 = 0 ( CCW + ) \sum M_{L3} = 0 \quad (\text{CCW } +) ∑ M L 3 = 0 ( CCW + ) − ( R × 9.0 ) + ( P 1 × 6.0 ) + ( P 2 × 3.0 ) − ( F U 2 U 3 × 4.0 ) = 0 -(R \times 9.0) + (P_1 \times 6.0) + (P_2 \times 3.0) - (F_{U2U3} \times 4.0) = 0 − ( R × 9.0 ) + ( P 1 × 6.0 ) + ( P 2 × 3.0 ) − ( F U 2 U 3 × 4.0 ) = 0 − ( 150.0 × 9.0 ) + ( 60.0 × 6.0 ) + ( 60.0 × 3.0 ) − 4.0 F U 2 U 3 = 0 -(150.0 \times 9.0) + (60.0 \times 6.0) + (60.0 \times 3.0) - 4.0 F_{U2U3} = 0 − ( 150.0 × 9.0 ) + ( 60.0 × 6.0 ) + ( 60.0 × 3.0 ) − 4.0 F U 2 U 3 = 0 − 1350.0 + 360.0 + 180.0 − 4.0 F U 2 U 3 = 0 -1350.0 + 360.0 + 180.0 - 4.0 F_{U2U3} = 0 − 1350.0 + 360.0 + 180.0 − 4.0 F U 2 U 3 = 0 − 810.0 − 4.0 F U 2 U 3 = 0 -810.0 - 4.0 F_{U2U3} = 0 − 810.0 − 4.0 F U 2 U 3 = 0 4.0 F U 2 U 3 = − 810.0 4.0 F_{U2U3} = -810.0 4.0 F U 2 U 3 = − 810.0 F U 2 U 3 = − 202.5 kN F_{U2U3} = -202.5\text{ kN} F U 2 U 3 = − 202.5 kN The negative sign indicates compression : F U 2 U 3 = 202.5 kN ( Compression ) F_{U2U3} = 202.5\text{ kN} \quad (\text{Compression}) F U 2 U 3 = 202.5 kN ( Compression )
Worked Example 2: Suspension Cable Analysis
Problem: A main suspension bridge cable spans L = 120.0 m L = 120.0\text{ m} L = 120.0 m between tower pylons at equal elevations. The cable supports a uniform deck load of w = 25.0 kN/m w = 25.0\text{ kN/m} w = 25.0 kN/m across the horizontal span. The central sag is designed at h = 10.0 m h = 10.0\text{ m} h = 10.0 m .
Calculate the minimum horizontal cable tension T 0 T_0 T 0 .
Calculate the maximum cable tension T max T_{\max} T m a x at the tower supports.
Estimate the total required cable arc length S S S .
Solution:
Step 1: Compute Minimum Horizontal Cable Tension ( T 0 T_0 T 0 ) T 0 = w L 2 8 h = 25.0 kN/m × ( 120.0 m ) 2 8 × 10.0 m = 25.0 × 14 , 400 80.0 = 360 , 000 80.0 = 4 , 500.0 kN T_0 = \frac{w L^2}{8 h} = \frac{25.0\text{ kN/m} \times (120.0\text{ m})^2}{8 \times 10.0\text{ m}} = \frac{25.0 \times 14,400}{80.0} = \frac{360,000}{80.0} = 4,500.0\text{ kN} T 0 = 8 h w L 2 = 8 × 10.0 m 25.0 kN/m × ( 120.0 m ) 2 = 80.0 25.0 × 14 , 400 = 80.0 360 , 000 = 4 , 500.0 kN
Step 2: Compute Maximum Cable Tension ( T max T_{\max} T m a x ) The vertical reaction at each support is half the total suspended weight: V max = w L 2 = 25.0 × 120.0 2 = 1 , 500.0 kN V_{\max} = \frac{w L}{2} = \frac{25.0 \times 120.0}{2} = 1,500.0\text{ kN} V m a x = 2 w L = 2 25.0 × 120.0 = 1 , 500.0 kN The maximum tension occurs at the towers: T max = T 0 2 + V max 2 = ( 4 , 500.0 ) 2 + ( 1 , 500.0 ) 2 = 20 , 250 , 000 + 2 , 250 , 000 T_{\max} = \sqrt{T_0^2 + V_{\max}^2} = \sqrt{(4,500.0)^2 + (1,500.0)^2} = \sqrt{20,250,000 + 2,250,000} T m a x = T 0 2 + V m a x 2 = ( 4 , 500.0 ) 2 + ( 1 , 500.0 ) 2 = 20 , 250 , 000 + 2 , 250 , 000 T max = 22 , 500 , 000 = 4 , 743.42 kN ≈ 4 , 743.4 kN T_{\max} = \sqrt{22,500,000} = 4,743.42\text{ kN} \approx 4,743.4\text{ kN} T m a x = 22 , 500 , 000 = 4 , 743.42 kN ≈ 4 , 743.4 kN
Step 3: Estimate Cable Arc Length ( S S S ) Using the parabolic series approximation: S ≈ L + 8 h 2 3 L = 120.0 + 8 × ( 10.0 ) 2 3 × 120.0 = 120.0 + 800.0 360.0 = 120.0 + 2.22 m = 122.22 m S \approx L + \frac{8 h^2}{3 L} = 120.0 + \frac{8 \times (10.0)^2}{3 \times 120.0} = 120.0 + \frac{800.0}{360.0} = 120.0 + 2.22\text{ m} = 122.22\text{ m} S ≈ L + 3 L 8 h 2 = 120.0 + 3 × 120.0 8 × ( 10.0 ) 2 = 120.0 + 360.0 800.0 = 120.0 + 2.22 m = 122.22 m
CELE Board Exam Traps & Strategic Checklists
Warning
Joint Method Starting Point: Never begin the Method of Joints at a node with 3 or more unknown member forces! Planar joints offer only two independent equations ( ∑ F x = 0 , ∑ F y = 0 \sum F_x = 0, \sum F_y = 0 ∑ F x = 0 , ∑ F y = 0 ). Always start at an exterior support or end pin having at most two unknowns .
Parabolic vs. Catenary Load Definition: In suspension cables, if the problem states "uniformly distributed per meter of span / deck", it is a parabola ( y = w x 2 / 2 T 0 y = w x^2 / 2 T_0 y = w x 2 /2 T 0 ). If it states "self-weight per meter of cable length", it is a catenary ( y = c cosh ( x / c ) y = c \cosh(x/c) y = c cosh ( x / c ) ). Using catenary equations for roadway loads produces needless complexity.
Internal Multi-Force Pins: In frames, internal pins connect two or more members. If a concentrated load acts directly on an internal pin, attribute that load to one member only (or treat the pin itself as a separate free body) to avoid double-counting the external force.