Study guide
7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
Key Takeaways Explain This Topic AI
Archimedes' principle dictates that any submerged or floating body experiences a vertical buoyant force F b = γ f V d F_b = \gamma_f V_d F b = γ f V d equal to the weight of displaced liquid, acting through the centroid of displaced volume known as the Center of Buoyancy (CB).
Rotational stability of floating vessels is governed by the metacentric height M G = M B ± G B MG = MB \pm GB MG = MB ± GB , where the metacentric radius M B = I / V d MB = I / V_d MB = I / V d utilizes the waterline area's moment of inertia about the tilting axis; positive M G MG MG ensures stable righting moments ( R M = W ⋅ M G sin θ RM = W \cdot MG \sin \theta RM = W ⋅ MG sin θ ).
A completely submerged body is in stable equilibrium if its center of gravity (G) lies directly below its center of buoyancy (B); if G is above B, the submerged body is in unstable equilibrium and will invert.
Fluids under uniform linear acceleration behave as rigid bodies with isobaric surfaces inclined at tan θ = a x g ± a y \tan \theta = \frac{a_x}{g \pm a_y} tan θ = g ± a y a x , where upward vertical acceleration increases hydrostatic gradients and downward free-fall reduces pressure to zero throughout.
In uniform forced vortex rotation ( ω \omega ω ), the free surface forms a paraboloid of revolution y = ω 2 x 2 2 g y = \frac{\omega^2 x^2}{2g} y = 2 g ω 2 x 2 with a total volume equal to exactly half that of its circumscribing cylinder ( V = 1 2 π R 2 H V = \frac{1}{2} \pi R^2 H V = 2 1 π R 2 H ), depressing the center and elevating the rim by equal amounts ( H / 2 H/2 H /2 ) in unspilled vessels.
Last updated: October 2026
7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
This section addresses the mechanics of floating and submerged bodies under static conditions, as well as the dynamic state of fluids subjected to constant linear acceleration or uniform rotation—a condition known in engineering mechanics as relative equilibrium of liquids .
1. Archimedes' Principle & Buoyant Force
Archimedes' Principle states that any body completely or partially submerged in a fluid experiences an upward vertical force equal to the weight of the fluid displaced by the body.
Mathematical Formulation
Consider an elemental vertical prism of height h = h 2 − h 1 h = h_2 - h_1 h = h 2 − h 1 and cross-sectional area d A dA d A submerged in a fluid of specific weight γ f \gamma_f γ f : d F b = ( P bottom − P top ) d A = ( γ f h 2 − γ f h 1 ) d A = γ f ( h 2 − h 1 ) d A = γ f d V dF_b = (P_{\text{bottom}} - P_{\text{top}}) dA = (\gamma_f h_2 - \gamma_f h_1) dA = \gamma_f (h_2 - h_1) dA = \gamma_f dV d F b = ( P bottom − P top ) d A = ( γ f h 2 − γ f h 1 ) d A = γ f ( h 2 − h 1 ) d A = γ f d V Integrating across the entire submerged body: F b = γ f V d = ρ f g V d F_b = \gamma_f V_d = \rho_f g V_d F b = γ f V d = ρ f g V d where:
F b F_b F b is the buoyant force ( kN \text{kN} kN or N \text{N} N ), acting vertically upward.
V d V_d V d is the displaced fluid volume (submerged volume of the body).
The line of action of F b F_b F b passes directly through the centroid of the displaced volume, designated as the Center of Buoyancy ( C B CB CB or B B B ) .
Principle of Flotation
For any body floating in static equilibrium in a single liquid, vertical force equilibrium requires: ∑ F y = 0 ⟹ W = F b ⟹ γ body V total = γ f V d \sum F_y = 0 \implies W = F_b \implies \gamma_{\text{body}} V_{\text{total}} = \gamma_f V_d ∑ F y = 0 ⟹ W = F b ⟹ γ body V total = γ f V d V d V total = γ body γ f = S G body S G f \frac{V_d}{V_{\text{total}}} = \frac{\gamma_{\text{body}}}{\gamma_f} = \frac{SG_{\text{body}}}{SG_f} V total V d = γ f γ body = S G f S G body For a prismatic floating body of uniform horizontal cross-section and total vertical height H H H , the draft (submerged depth D D D ) is: D = H ( S G body S G f ) D = H \left(\frac{SG_{\text{body}}}{SG_f}\right) D = H ( S G f S G body )
- 2. Stability of Submerged vs. Floating Bodies
- Submerged Bodies (Submarines, Torpedoes)
For completely submerged bodies, the displaced shape does not change as the body rotates, so the Center of Buoyancy ( B B B ) remains fixed relative to the body.
Stable Equilibrium: Center of Gravity ( G G G ) lies vertically below the Center of Buoyancy ( B B B ). Any angular tilt creates a restoring righting couple ( W W W downward at G G G , F b F_b F b upward at B B B ).
Unstable Equilibrium: G G G lies vertically above B B B . Any slight tilt creates an overturning couple that causes the body to capsize until G G G settles below B B B .
Neutral Equilibrium: G G G and B B B coincide.
Loading diagram...
Floating Bodies and the Metacenter ( M M M )
When a floating body heels (tilts) by an angle θ \theta θ , the submerged geometry changes, shifting the Center of Buoyancy from B B B to a new position B ′ B' B ′ . The vertical line of action through B ′ B' B ′ intersects the original vertical axis of symmetry at the Metacenter ( M M M ) .
Metacentric Radius ( M B MB MB )
By equating the moment of the submerged volume shift (wedges of immersion and emersion) to the moment of the buoyant force: M B = I V d MB = \frac{I}{V_d} MB = V d I where:
I I I is the second moment of area (moment of inertia) of the waterline horizontal plane about the tilting axis (longitudinal axis for rolling, transverse axis for pitching).
V d V_d V d is the displaced volume of fluid.
Important
Roll vs. Pitch Axis of Rotation: For a rectangular floating barge of length L L L , width B B B , and draft D D D , rolling occurs about its longitudinal axis, so the relevant moment of inertia uses the smaller transverse dimension cubed: I roll = L B 3 12 I_{\text{roll}} = \frac{L B^3}{12} I roll = 12 L B 3 .
Thus: M B = I roll V d = 1 12 L B 3 L B D = B 2 12 D MB = \frac{I_{\text{roll}}}{V_d} = \frac{\frac{1}{12} L B^3}{L B D} = \frac{B^2}{12 D} MB = V d I roll = L B D 12 1 L B 3 = 12 D B 2
Metacentric Height ( M G MG MG )
The metacentric height ( M G MG MG ) is the primary measure of floating stability: M G = M B ± G B MG = MB \pm GB MG = MB ± GB
If G G G is located above B B B : M G = M B − G B = I V d − G B MG = MB - GB = \frac{I}{V_d} - GB MG = MB − GB = V d I − GB .
If G G G is located below B B B : M G = M B + G B = I V d + G B MG = MB + GB = \frac{I}{V_d} + GB MG = MB + GB = V d I + GB .
Stability Conditions for Floating Bodies:
M G > 0 MG > 0 MG > 0 ( M M M above G G G ): Stable equilibrium. A restoring couple forms to return the vessel to upright.
M G = 0 MG = 0 MG = 0 ( M M M at G G G ): Neutral equilibrium. The vessel remains in the tilted position without restoring or capsizing forces.
M G < 0 MG < 0 MG < 0 ( M M M below G G G ): Unstable equilibrium. An overturning couple accelerates the heel, causing capsizing.
Righting and Overturning Moments
For small angles of heel (typically θ ≤ 10 ∘ – 12 ∘ \theta \le 10^\circ\text{–}12^\circ θ ≤ 1 0 ∘ – 1 2 ∘ ): R M = W ⋅ G Z ‾ = W ⋅ M G sin θ RM = W \cdot \overline{GZ} = W \cdot MG \sin \theta RM = W ⋅ GZ = W ⋅ MG sin θ where G Z ‾ = M G sin θ \overline{GZ} = MG \sin \theta GZ = MG sin θ is the righting arm .
3. Relative Equilibrium: Uniform Linear Acceleration
When a container of liquid accelerates uniformly, no relative motion occurs between fluid particles; the liquid behaves as a rigid body with zero internal shear stresses.
Governing Differential Equations
Summing forces on a fluid element of mass d m = ρ d x d y d z dm = \rho dx dy dz d m = ρ d x d y d z undergoing acceleration components a x a_x a x (horizontal) and a y a_y a y (vertical): ∂ P ∂ x = − ρ a x , ∂ P ∂ y = − ρ ( g ± a y ) \frac{\partial P}{\partial x} = -\rho a_x, \quad \frac{\partial P}{\partial y} = -\rho (g \pm a_y) ∂ x ∂ P = − ρ a x , ∂ y ∂ P = − ρ ( g ± a y )
Inclination of Isobaric Surfaces (Free Surface Angle θ \theta θ )
Surfaces of constant pressure (isobars), including the liquid free surface, tilt at an angle θ \theta θ relative to the horizontal: tan θ = a x g ± a y \tan \theta = \frac{a_x}{g \pm a_y} tan θ = g ± a y a x
Vertical Acceleration Convention: Use + a y +a_y + a y for upward acceleration and − a y -a_y − a y for downward acceleration.
If a container is in free fall ( a y = − g a_y = -g a y = − g ), tan θ → ∞ \tan \theta \to \infty tan θ → ∞ and hydrostatic pressure drops to zero everywhere ( P = 0 P = 0 P = 0 ).
Pressure Variation in Linearly Accelerated Fluids
P 2 − P 1 = ρ a x ( x 1 − x 2 ) + ρ ( g ± a y ) ( y 1 − y 2 ) P_2 - P_1 = \rho a_x (x_1 - x_2) + \rho (g \pm a_y) (y_1 - y_2) P 2 − P 1 = ρ a x ( x 1 − x 2 ) + ρ ( g ± a y ) ( y 1 − y 2 ) For purely vertical depth h h h below the free surface: P = γ ( 1 ± a y g ) h P = \gamma \left(1 \pm \frac{a_y}{g}\right) h P = γ ( 1 ± g a y ) h
Surface Geometry in Open and Closed Rectangular Tanks
Open Tanks (No Spill): The liquid volume is conserved, so the free surface pivots about the centroid of the original static surface. If length is L L L , the liquid rises at the trailing wall and drops at the leading wall by: Δ y = L 2 tan θ \Delta y = \frac{L}{2} \tan \theta Δ y = 2 L tan θ
Open Tanks (Spilling): If Δ y \Delta y Δ y exceeds the original freeboard, liquid spills over the edge, and the remaining liquid volume determines the new free surface plane.
4. Relative Equilibrium: Uniform Rotation (Forced Vortex)
When a cylindrical tank of liquid rotates about its vertical centerline at constant angular velocity ω \omega ω ( rad/s \text{rad/s} rad/s ), centripetal acceleration ( a r = − ω 2 r a_r = -\omega^2 r a r = − ω 2 r ) drives the liquid outwards, creating a forced vortex .
Loading diagram...
Equation of the Parabolic Free Surface
From the balance of radial pressure gradient and centrifugal force ∂ P ∂ r = ρ ω 2 r \frac{\partial P}{\partial r} = \rho \omega^2 r ∂ r ∂ P = ρ ω 2 r and vertical hydrostatic balance ∂ P ∂ z = − ρ g \frac{\partial P}{\partial z} = -\rho g ∂ z ∂ P = − ρ g : d z d r = ω 2 r g ⟹ z = ω 2 r 2 2 g + C \frac{dz}{dr} = \frac{\omega^2 r}{g} \implies z = \frac{\omega^2 r^2}{2g} + C d r d z = g ω 2 r ⟹ z = 2 g ω 2 r 2 + C Measuring the vertical coordinate y y y from the lowest point (vertex) of the paraboloid: y = ω 2 r 2 2 g y = \frac{\omega^2 r^2}{2g} y = 2 g ω 2 r 2 At the outer container wall ( r = R r = R r = R ): H = ω 2 R 2 2 g H = \frac{\omega^2 R^2}{2g} H = 2 g ω 2 R 2 where H H H is the total height of the paraboloid of revolution.
Critical Geometric Properties of the Paraboloid
Volume of the Paraboloid: V paraboloid = 1 2 π R 2 H V_{\text{paraboloid}} = \frac{1}{2} \pi R^2 H V paraboloid = 2 1 π R 2 H The volume of a paraboloid of revolution equals exactly one-half the volume of its circumscribing cylinder of radius R R R and height H H H .
Unspilled Liquid Symmetry Rule: If no liquid spills from the open cylinder, the volume of air space before rotation equals the volume of the paraboloid above the vertex. Consequently, the liquid rises at the perimeter wall by H / 2 H/2 H /2 and depresses at the center axis by H / 2 H/2 H /2 relative to the original static liquid level ( d 0 d_0 d 0 ): d rim = d 0 + H 2 , d center = d 0 − H 2 d_{\text{rim}} = d_0 + \frac{H}{2}, \quad d_{\text{center}} = d_0 - \frac{H}{2} d rim = d 0 + 2 H , d center = d 0 − 2 H
Base Pressure Distribution: Pressure at the bottom of the container varies with radial position r r r : P ( r ) = γ h ( r ) = γ ( d center + ω 2 r 2 2 g ) P(r) = \gamma h(r) = \gamma \left(d_{\text{center}} + \frac{\omega^2 r^2}{2g}\right) P ( r ) = γh ( r ) = γ ( d center + 2 g ω 2 r 2 )
Minimum pressure occurs at the center ( r = 0 r = 0 r = 0 ): P center = γ d center P_{\text{center}} = \gamma d_{\text{center}} P center = γ d center .
Maximum pressure occurs at the outer rim ( r = R r = R r = R ): P rim = γ d rim P_{\text{rim}} = \gamma d_{\text{rim}} P rim = γ d rim .
5. Worked Example: Floating Timber Scow Stability
Problem Statement: A rectangular timber scow has a width of B = 6.0 m B = 6.0\text{ m} B = 6.0 m , a length of L = 12.0 m L = 12.0\text{ m} L = 12.0 m , and a total height of 3.0 m 3.0\text{ m} 3.0 m . The total weight of the scow and its cargo is W = 1 , 271.4 kN W = 1,271.4\text{ kN} W = 1 , 271.4 kN . It floats in seawater with a specific weight of γ s w = 10.05 kN/m 3 \gamma_{sw} = 10.05\text{ kN/m}^3 γ s w = 10.05 kN/m 3 . The composite center of gravity ( G G G ) is located along the vertical centerline at K G = 1.60 m KG = 1.60\text{ m} K G = 1.60 m above the flat bottom.
Determine the draft D D D of the scow.
Determine the metacentric height M G MG MG for rolling.
Determine the righting moment R M RM RM when the scow heels by an angle of θ = 6 ∘ \theta = 6^\circ θ = 6 ∘ .
Step-by-Step Solution:
Determine draft D D D :
By Archimedes' principle: W = F b = γ s w V d W = F_b = \gamma_{sw} V_d W = F b = γ s w V d V d = W γ s w = 1 , 271.4 kN 10.05 kN/m 3 = 126.51 m 3 V_d = \frac{W}{\gamma_{sw}} = \frac{1,271.4\text{ kN}}{10.05\text{ kN/m}^3} = 126.51\text{ m}^3 V d = γ s w W = 10.05 kN/m 3 1 , 271.4 kN = 126.51 m 3
Displaced volume is V d = L × B × D V_d = L \times B \times D V d = L × B × D : D = V d L × B = 126.51 m 3 12.0 m × 6.0 m = 126.51 72.0 = 1.757 m D = \frac{V_d}{L \times B} = \frac{126.51\text{ m}^3}{12.0\text{ m} \times 6.0\text{ m}} = \frac{126.51}{72.0} = 1.757\text{ m} D = L × B V d = 12.0 m × 6.0 m 126.51 m 3 = 72.0 126.51 = 1.757 m
Determine Metacentric Height ( M G MG MG ):
Center of Buoyancy ( B B B ) from the bottom: K B = D 2 = 1.757 m 2 = 0.879 m KB = \frac{D}{2} = \frac{1.757\text{ m}}{2} = 0.879\text{ m} K B = 2 D = 2 1.757 m = 0.879 m
Distance from B B B to G G G ( G G G is above B B B ): G B = K G − K B = 1.600 m − 0.879 m = 0.721 m GB = KG - KB = 1.600\text{ m} - 0.879\text{ m} = 0.721\text{ m} GB = K G − K B = 1.600 m − 0.879 m = 0.721 m
Metacentric radius M B MB MB for roll (rotation about longitudinal centerline): M B = B 2 12 D = ( 6.0 m ) 2 12 ( 1.757 m ) = 36.0 21.084 = 1.707 m MB = \frac{B^2}{12 D} = \frac{(6.0\text{ m})^2}{12 (1.757\text{ m})} = \frac{36.0}{21.084} = 1.707\text{ m} MB = 12 D B 2 = 12 ( 1.757 m ) ( 6.0 m ) 2 = 21.084 36.0 = 1.707 m
Metacentric height: M G = M B − G B = 1.707 m − 0.721 m = + 0.986 m MG = MB - GB = 1.707\text{ m} - 0.721\text{ m} = +0.986\text{ m} MG = MB − GB = 1.707 m − 0.721 m = + 0.986 m
Because M G > 0 MG > 0 MG > 0 , the vessel is in stable equilibrium .
Determine Righting Moment ( R M RM RM at θ = 6 ∘ \theta = 6^\circ θ = 6 ∘ ): R M = W ⋅ M G sin θ = ( 1 , 271.4 kN ) ( 0.986 m ) sin 6 ∘ RM = W \cdot MG \sin \theta = (1,271.4\text{ kN})(0.986\text{ m}) \sin 6^\circ RM = W ⋅ MG sin θ = ( 1 , 271.4 kN ) ( 0.986 m ) sin 6 ∘ R M = ( 1 , 253.6 kN ⋅ m ) ( 0.10453 ) = 131.04 kN ⋅ m RM = (1,253.6\text{ kN}\cdot\text{m})(0.10453) = 131.04\text{ kN}\cdot\text{m} RM = ( 1 , 253.6 kN ⋅ m ) ( 0.10453 ) = 131.04 kN ⋅ m
6. CELE Exam Traps & Common Computational Errors
Warning
Trap 1: Using the Long Axis in Rolling Metacentric Height: Rolling stability is evaluated about the vessel's longitudinal axis, meaning the width B B B is cubed in I = L B 3 12 I = \frac{L B^3}{12} I = 12 L B 3 . Using B L 3 12 \frac{B L^3}{12} 12 B L 3 evaluates pitching stability, which artificially inflates M B MB MB by a factor of ( L / B ) 2 (L/B)^2 ( L / B ) 2 and gives a dangerously false sense of roll stability.
Warning
Trap 2: Treating Paraboloid Volume as a Cone: The volume of a paraboloid of revolution is V = 1 2 π R 2 H V = \frac{1}{2}\pi R^2 H V = 2 1 π R 2 H . Treating it as a cone ( V = 1 3 π R 2 H V = \frac{1}{3}\pi R^2 H V = 3 1 π R 2 H ) is a frequent board exam mistake that leads to incorrect spilled volume and rotational speed calculations.
Warning
Trap 3: Sign of Vertical Acceleration in Liquid Incline: In tan θ = a x g ± a y \tan \theta = \frac{a_x}{g \pm a_y} tan θ = g ± a y a x , upward vertical acceleration increases the effective gravitational field ( g + a y g + a_y g + a y ), decreasing the free surface tilt angle θ \theta θ . Downward acceleration decreases effective gravity ( g − a y g - a_y g − a y ), increasing the tilt angle.