Study guide

10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls

PRC Civil Engineer Licensure Examination CELE

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Examination Overview, RA 544 & Professional Practice

1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice

2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics

2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum

3 Chapter 3: Engineering Data Analysis & Engineering Economy

3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis

4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying

4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves

5 Chapter 5: Highway & Transportation Engineering

5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems

6 Chapter 6: Construction Materials, Methods, Management & Safety

6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical

7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy

7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses

8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply

8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment

9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass

9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement

10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations

10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability

11 Chapter 11: Engineering Mechanics & Statics

11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members

12 Chapter 12: Strength of Materials

12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle

13 Chapter 13: Structural Analysis & NSCP Load Criteria

13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake

14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)

14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design

15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing

15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning

10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls

Key Takeaways Explain This Topic AI

Lateral earth pressures exist in three distinct operational states: at-rest (K0 = 1 - sin φ'), active (Ka), and passive (Kp), where active failure requires minimal outward wall rotation while passive failure demands substantially larger inward displacement.

Rankine's theory assumes a frictionless, vertical wall retaining a horizontal soil backfill, producing Ka = tan²(45° - φ/2) = (1 - sin φ)/(1 + sin φ) and Kp = tan²(45° + φ/2) = 1/Ka.

In cohesive (c - φ) backfills, tensile stresses develop near the surface down to the critical tension crack depth zc = 2c / (γ √Ka); tension cracks filled with hydrostatic water pressure severely amplify the total destabilizing lateral thrust.

Coulomb's wedge theory incorporates wall-soil interface friction (δ), backfill inclination (α), and stem batter (β), producing a resultant thrust inclined at angle δ to the wall normal.

Rigid retaining wall stability mandates verification of three primary safety factors: overturning (FSot ≥ 2.0), sliding along the base (FSsl ≥ 1.5), and bearing capacity without base tension (resultant eccentricity e ≤ B/6).

Last updated: October 2026

10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls

Earth retaining structures—such as gravity walls, reinforced concrete cantilever walls, bridge abutments, and sheet pile bulkheads—must support lateral thrust from retained soil masses and surface surcharges. Board exam problems in this domain require analyzing earth pressure distributions and checking the overall external stability of the retaining structure against overturning, sliding, and foundation bearing failure.

The Three Lateral Earth Pressure States

The magnitude of lateral earth pressure exerted by a soil mass against a retaining wall depends strictly on the magnitude and direction of lateral wall displacement ( Δ x / H \Delta x / H Δ x / H ): Lateral Earth Pressure (σ_h)

  • ^
  • | Passive State (K_p)
  • | .--------
  • | .'
  • | .'
  • | At-Rest (K_0) .'
  • | *---------'
  • | .'
  • | .'
  • | .----------' Active State (K_a)
  • |
  • +------------------|-------------------|-------------------> Wall Movement
  • <-- Away from Soil (Active) Into Soil (Passive) -->
  • 1. At-Rest Earth Pressure ( K 0 K_0 K 0 ​ )

Occurs when the wall is completely rigid and unyielding (zero lateral strain, ϵ x = 0 \epsilon_x = 0 ϵ x ​ = 0 ), such as massive bridge abutments keyed into solid bedrock or basement retaining walls restrained by floor diaphragms.

For normally consolidated cohesionless soils, Jaky's empirical equation applies: K 0 ≈ 1 − sin ⁡ ϕ ′ K_0 \approx 1 - \sin \phi' K 0 ​ ≈ 1 − sin ϕ ′

For overconsolidated soils, the coefficient increases with overconsolidation ratio ( O C R OCR OCR ): K 0 , O C = K 0 , N C O C R = ( 1 − sin ⁡ ϕ ′ ) O C R K_{0,OC} = K_{0,NC} \sqrt{OCR} = (1 - \sin \phi') \sqrt{OCR} K 0 , OC ​ = K 0 , NC ​ OCR ​ = ( 1 − sin ϕ ′ ) OCR ​

2. Active Earth Pressure ( K a K_a K a ​ )

Occurs when the wall tilts or translates away from the backfill . As the wall moves outward, the soil expands laterally, mobilizing internal shear strength along an active failure wedge. Lateral stress decreases until reaching a lower-bound minimum at active shear failure.

Displacement Required: Very small outward movement, typically Δ x / H ≈ 0.001 to 0.004 \Delta x / H \approx 0.001 \text{ to } 0.004 Δ x / H ≈ 0.001 to 0.004 (roughly 1 to 4 mm 1\text{ to } 4\text{ mm} 1 to 4 mm per meter of wall height for sand).

3. Passive Earth Pressure ( K p K_p K p ​ )

Occurs when the wall is forced into the backfill (such as anchor slabs or the soil wedge resisting the toe of a retaining wall). Lateral stress increases as the soil is compressed, reaching an upper-bound maximum at passive shear failure.

Displacement Required: Significantly larger inward displacement, typically Δ x / H ≈ 0.01 to 0.05 \Delta x / H \approx 0.01 \text{ to } 0.05 Δ x / H ≈ 0.01 to 0.05 (roughly 10 times the movement required for the active state).

Magnitude Relationship: K a < K 0 < K p \text{Magnitude Relationship: } K_a < K_0 < K_p Magnitude Relationship: K a ​ < K 0 ​ < K p ​

Rankine's Lateral Earth Pressure Theory

Formulated by William John Macquorn Rankine in 1857, this theory assumes:

The backfill soil is homogeneous and isotropic.

The back of the retaining wall is perfectly vertical ( β = 90 ∘ \beta = 90^\circ β = 9 0 ∘ ) and frictionless (wall friction angle δ = 0 \delta = 0 δ = 0 ).

The backfill surface is planar (horizontal or uniformly inclined at angle α \alpha α ).

The failure surface in the soil is a planar slip boundary.

Cohesionless Backfill ( c = 0 c = 0 c = 0 , Horizontal Surface)

For a dry, homogeneous sand of unit weight γ \gamma γ and internal friction angle ϕ \phi ϕ :

Active Pressure Coefficient ( K a K_a K a ​ ): K a = tan ⁡ 2 ( 45 ∘ − ϕ 2 ) = 1 − sin ⁡ ϕ 1 + sin ⁡ ϕ K_a = \tan^2\left(45^\circ - \frac{\phi}{2}\right) = \frac{1 - \sin \phi}{1 + \sin \phi} K a ​ = tan 2 ( 4 5 ∘ − 2 ϕ ​ ) = 1 + s i n ϕ 1 − s i n ϕ ​ Active lateral stress at depth z z z : σ a = γ z K a \sigma_a = \gamma z K_a σ a ​ = γ z K a ​ Total active resultant thrust per unit length of wall: P a = 1 2 γ H 2 K a ( acting at y = H / 3 from the base ) P_a = \frac{1}{2} \gamma H^2 K_a \quad (\text{acting at } y = H/3 \text{ from the base}) P a ​ = 2 1 ​ γ H 2 K a ​ ( acting at y = H /3 from the base )

Passive Pressure Coefficient ( K p K_p K p ​ ): K p = tan ⁡ 2 ( 45 ∘ + ϕ 2 ) = 1 + sin ⁡ ϕ 1 − sin ⁡ ϕ = 1 K a K_p = \tan^2\left(45^\circ + \frac{\phi}{2}\right) = \frac{1 + \sin \phi}{1 - \sin \phi} = \frac{1}{K_a} K p ​ = tan 2 ( 4 5 ∘ + 2 ϕ ​ ) = 1 − s i n ϕ 1 + s i n ϕ ​ = K a ​ 1 ​ Total passive resultant resistance: P p = 1 2 γ H 2 K p ( acting at y = H / 3 from the base ) P_p = \frac{1}{2} \gamma H^2 K_p \quad (\text{acting at } y = H/3 \text{ from the base}) P p ​ = 2 1 ​ γ H 2 K p ​ ( acting at y = H /3 from the base )

Surcharge and Groundwater Stratification

When external conditions act on the backfill, their lateral pressure contributions superimpose:

Uniform Surcharge ( q q q ): A surface surcharge load q q q (in kPa \text{kPa} kPa ) exerts a constant uniform lateral pressure along the entire wall height: σ a , q = q K a ⟹ P q = q K a H ( acting at y = H / 2 ) \sigma_{a,q} = q K_a \implies P_q = q K_a H \quad (\text{acting at } y = H/2) σ a , q ​ = q K a ​ ⟹ P q ​ = q K a ​ H ( acting at y = H /2 )

Water Table Effects: Water is an isotropic fluid with zero shear resistance ( K w = 1.0 K_w = 1.0 K w ​ = 1.0 ). If the groundwater table is located at depth h 1 h_1 h 1 ​ below the crest:

Above the water table ( z ≤ h 1 z \le h_1 z ≤ h 1 ​ ): σ v ′ = γ z \sigma'_v = \gamma z σ v ′ ​ = γ z , and lateral stress is σ a ′ = γ z K a \sigma'_a = \gamma z K_a σ a ′ ​ = γ z K a ​ .

Below the water table ( z > h 1 z > h_1 z > h 1 ​ ): effective vertical stress is σ v ′ = γ h 1 + γ ′ ( z − h 1 ) \sigma'_v = \gamma h_1 + \gamma' (z - h_1) σ v ′ ​ = γ h 1 ​ + γ ′ ( z − h 1 ​ ) , where buoyant unit weight is γ ′ = γ sat − γ w \gamma' = \gamma_{\text{sat}} - \gamma_w γ ′ = γ sat ​ − γ w ​ . The lateral effective stress is σ a ′ = σ v ′ K a \sigma'_a = \sigma'_v K_a σ a ′ ​ = σ v ′ ​ K a ​ .

Hydrostatic Water Thrust: The water pressure acts independently and must be added directly: u = γ w ( z − h 1 ) ⟹ P w = 1 2 γ w ( H − h 1 ) 2 ( acting at ( H − h 1 ) / 3 ) u = \gamma_w (z - h_1) \implies P_w = \frac{1}{2} \gamma_w (H - h_1)^2 \quad (\text{acting at } (H - h_1)/3) u = γ w ​ ( z − h 1 ​ ) ⟹ P w ​ = 2 1 ​ γ w ​ ( H − h 1 ​ ) 2 ( acting at ( H − h 1 ​ ) /3 )

Caution

Never multiply pore water pressure by K a K_a K a ​ ! Water possesses no shear strength, so lateral water pressure is identical in all directions ( K w = 1.0 K_w = 1.0 K w ​ = 1.0 ). Multiplying hydrostatic water pressure by K a K_a K a ​ is an automatic failure trap on the CELE.

Cohesive Backfill ( c − ϕ c - \phi c − ϕ Soils) & Tension Cracks

For a cohesive soil possessing both cohesion c c c and friction angle ϕ \phi ϕ , Rankine active pressure is: σ a = γ z K a − 2 c K a \sigma_a = \gamma z K_a - 2 c \sqrt{K_a} σ a ​ = γ z K a ​ − 2 c K a ​ ​

At the ground surface ( z = 0 z = 0 z = 0 ), the lateral stress is tensile: σ a = − 2 c K a \sigma_a = -2 c \sqrt{K_a} σ a ​ = − 2 c K a ​ ​ . Because soil possesses negligible tensile strength, tension cracks develop down to a critical depth z c z_c z c ​ where σ a = 0 \sigma_a = 0 σ a ​ = 0 : γ z c K a − 2 c K a = 0 ⟹ z c = 2 c γ K a \gamma z_c K_a - 2 c \sqrt{K_a} = 0 \implies z_c = \frac{2 c}{\gamma \sqrt{K_a}} γ z c ​ K a ​ − 2 c K a ​ ​ = 0 ⟹ z c ​ = γ K a ​ ​ 2 c ​ Depth (z)

  • |
  • 0 -2c√Ka (Tension Zone)
  • | /|
  • | / |
  • |/ | zc = 2c / (γ√Ka)
  • zc---|----------------- Tension Crack Depth
  • |\ |
  • | \ | Active Compression Zone
  • | \|
  • H +----------------- σ_a = γ H Ka - 2c√Ka

Total active thrust calculations depend on crack condition:

Condition 1 (No Water in Crack, Tension Ignored): P a = 1 2 ( γ H K a − 2 c K a ) ( H − z c ) = 1 2 γ K a ( H − z c ) 2 P_a = \frac{1}{2} (\gamma H K_a - 2 c \sqrt{K_a})(H - z_c) = \frac{1}{2} \gamma K_a (H - z_c)^2 P a ​ = 2 1 ​ ( γ H K a ​ − 2 c K a ​ ​ ) ( H − z c ​ ) = 2 1 ​ γ K a ​ ( H − z c ​ ) 2 Acting at y = ( H − z c ) / 3 y = (H - z_c) / 3 y = ( H − z c ​ ) /3 above the base.

Condition 2 (Crack Completely Filled with Rainwater): Rainwater fills the open fissure, exerting full hydrostatic thrust P w = 1 2 γ w z c 2 P_w = \frac{1}{2} \gamma_w z_c^2 P w ​ = 2 1 ​ γ w ​ z c 2 ​ on the crack walls: P total = P a + P w = 1 2 γ K a ( H − z c ) 2 + 1 2 γ w z c 2 P_{\text{total}} = P_a + P_w = \frac{1}{2} \gamma K_a (H - z_c)^2 + \frac{1}{2} \gamma_w z_c^2 P total ​ = P a ​ + P w ​ = 2 1 ​ γ K a ​ ( H − z c ​ ) 2 + 2 1 ​ γ w ​ z c 2 ​

Coulomb's Earth Pressure Theory

Formulated by Charles-Augustin de Coulomb in 1776, this wedge equilibrium theory addresses practical wall geometries:

Accounts for wall friction angle δ \delta δ (typically δ ≈ 1 2 ϕ ′ to 2 3 ϕ ′ \delta \approx \frac{1}{2}\phi' \text{ to } \frac{2}{3}\phi' δ ≈ 2 1 ​ ϕ ′ to 3 2 ​ ϕ ′ between concrete and soil).

Accounts for sloping back of wall (batter β \beta β ) and sloping backfill (inclination α \alpha α ) .

The active thrust P a P_a P a ​ acts at an angle δ \delta δ to the normal drawn to the back face of the wall.

Active Coefficient K a = sin ⁡ 2 ( β + ϕ ) sin ⁡ 2 β sin ⁡ ( β − δ ) [ 1 + sin ⁡ ( ϕ + δ ) sin ⁡ ( ϕ − α ) sin ⁡ ( β − δ ) sin ⁡ ( β + α ) ] 2 \text{Active Coefficient } K_a = \frac{\sin^2(\beta + \phi)}{\sin^2\beta \sin(\beta - \delta) \left[ 1 + \sqrt{\frac{\sin(\phi + \delta) \sin(\phi - \alpha)}{\sin(\beta - \delta) \sin(\beta + \alpha)}} \right]^2} Active Coefficient K a ​ = s i n 2 β s i n ( β − δ ) [ 1 + s i n ( β − δ ) s i n ( β + α ) s i n ( ϕ + δ ) s i n ( ϕ − α ) ​ ​ ] 2 s i n 2 ( β + ϕ ) ​

When the back of the wall is vertical ( β = 90 ∘ \beta = 90^\circ β = 9 0 ∘ ), the backfill is horizontal ( α = 0 \alpha = 0 α = 0 ), and wall friction is zero ( δ = 0 \delta = 0 δ = 0 ), Coulomb's equation reduces exactly to Rankine's K a K_a K a ​ .

  • Retaining Wall External Stability Checks
  • A rigid retaining wall must satisfy three fundamental stability criteria under service loads: | | Stem
  • | |
  • | | Active Thrust P_a
  • | | <-----------------
  • | |
  • +-------+---+-----------+
  • | Toe | | Heel | Base Slab (Width B)
  • +-------+---+-----------+
  • |<--x-->| Resultant R
  • ^----/
  • 1. Stability Against Overturning

Evaluated by summing moments about the toe of the wall base slab: F S o t = ∑ M R ∑ M O ≥ 2.0 ( or 1.5 under earthquake load ) FS_{ot} = \frac{\sum M_R}{\sum M_O} \ge 2.0 \quad (\text{or } 1.5 \text{ under earthquake load}) F S o t ​ = ∑ M O ​ ∑ M R ​ ​ ≥ 2.0 ( or 1.5 under earthquake load ) Where ∑ M R \sum M_R ∑ M R ​ is the sum of resisting moments (from concrete weight and soil weight above the heel) and ∑ M O \sum M_O ∑ M O ​ is the sum of overturning moments (from horizontal earth and surcharge thrusts).

2. Stability Against Sliding

Evaluated along the base-soil interface: F S s l = ∑ F R ∑ F d = ( ∑ V ) tan ⁡ δ b + c a B + P p P h ≥ 1.5 FS_{sl} = \frac{\sum F_R}{\sum F_d} = \frac{(\sum V) \tan \delta_b + c_a B + P_p}{P_h} \ge 1.5 F S s l ​ = ∑ F d ​ ∑ F R ​ ​ = P h ​ ( ∑ V ) t a n δ b ​ + c a ​ B + P p ​ ​ ≥ 1.5 Where ∑ V \sum V ∑ V is total vertical force, δ b ≈ 2 3 ϕ ′ \delta_b \approx \frac{2}{3}\phi' δ b ​ ≈ 3 2 ​ ϕ ′ is base friction angle, c a ≈ 2 3 c ′ c_a \approx \frac{2}{3}c' c a ​ ≈ 3 2 ​ c ′ is base adhesion, and P h P_h P h ​ is the horizontal driving thrust. Passive resistance P p P_p P p ​ in front of the toe is frequently discounted by 50 % 50\% 50% or neglected entirely due to potential future utility trench excavation.

3. Base Bearing Pressure & Eccentricity Check

The resultant normal force R = ∑ V R = \sum V R = ∑ V acts at location x ˉ \bar{x} x ˉ from the toe: x ˉ = ∑ M R − ∑ M O ∑ V \bar{x} = \frac{\sum M_R - \sum M_O}{\sum V} x ˉ = ∑ V ∑ M R ​ − ∑ M O ​ ​ Eccentricity e = B 2 − x ˉ \text{Eccentricity } e = \frac{B}{2} - \bar{x} Eccentricity e = 2 B ​ − x ˉ

To prevent tensile detachment at the heel of the foundation, the resultant must fall within the middle third of the base slab: e ≤ B 6 e \le \frac{B}{6} e ≤ 6 B ​

If e ≤ B / 6 e \le B/6 e ≤ B /6 , the contact pressure distribution is trapezoidal: q = ∑ V B ( 1 ± 6 e B ) q = \frac{\sum V}{B} \left( 1 \pm \frac{6e}{B} \right) q = B ∑ V ​ ( 1 ± B 6 e ​ ) q max ⁡ = ∑ V B ( 1 + 6 e B ) ≤ q allowable q_{\max} = \frac{\sum V}{B} \left( 1 + \frac{6e}{B} \right) \le q_{\text{allowable}} q m a x ​ = B ∑ V ​ ( 1 + B 6 e ​ ) ≤ q allowable ​ q min ⁡ = ∑ V B ( 1 − 6 e B ) ≥ 0 q_{\min} = \frac{\sum V}{B} \left( 1 - \frac{6e}{B} \right) \ge 0 q m i n ​ = B ∑ V ​ ( 1 − B 6 e ​ ) ≥ 0

  • Step-by-Step Worked Problem Examples
  • Worked Example: Cantilever Retaining Wall Stability Analysis

Problem: A reinforced concrete cantilever retaining wall supports a horizontal granular backfill. The total wall height is H = 6.0 m H = 6.0\text{ m} H = 6.0 m , base width is B = 3.5 m B = 3.5\text{ m} B = 3.5 m , base slab thickness is 0.6 m 0.6\text{ m} 0.6 m , and vertical stem thickness is 0.4 m 0.4\text{ m} 0.4 m . The stem is positioned such that the toe length is 0.8 m 0.8\text{ m} 0.8 m and the heel length is 2.3 m 2.3\text{ m} 2.3 m ( 0.8 + 0.4 + 2.3 = 3.5 m 0.8 + 0.4 + 2.3 = 3.5\text{ m} 0.8 + 0.4 + 2.3 = 3.5 m ). Backfill properties: γ = 18.0 kN/m 3 \gamma = 18.0\text{ kN/m}^3 γ = 18.0 kN/m 3 , ϕ = 30 ∘ \phi = 30^\circ ϕ = 3 0 ∘ , c = 0 c = 0 c = 0 . A uniform surcharge q = 20.0 kPa q = 20.0\text{ kPa} q = 20.0 kPa acts on the backfill surface. Unit weight of reinforced concrete is γ c = 24.0 kN/m 3 \gamma_c = 24.0\text{ kN/m}^3 γ c ​ = 24.0 kN/m 3 .

Calculate the total horizontal driving active thrust P h P_h P h ​ and overturning moment M O M_O M O ​ about the toe.

Compute the factor of safety against overturning ( F S o t FS_{ot} F S o t ​ ).

Determine the base resultant eccentricity e e e and maximum soil contact pressure q max ⁡ q_{\max} q m a x ​ .

Solution:

Step 1: Compute Earth Pressure and Overturning Thrust K a = tan ⁡ 2 ( 45 ∘ − 30 ∘ / 2 ) = 1 − sin ⁡ 30 ∘ 1 + sin ⁡ 30 ∘ = 0.50 1.50 = 1 3 ≈ 0.3333 K_a = \tan^2(45^\circ - 30^\circ/2) = \frac{1 - \sin 30^\circ}{1 + \sin 30^\circ} = \frac{0.50}{1.50} = \frac{1}{3} \approx 0.3333 K a ​ = tan 2 ( 4 5 ∘ − 3 0 ∘ /2 ) = 1 + s i n 3 0 ∘ 1 − s i n 3 0 ∘ ​ = 1.50 0.50 ​ = 3 1 ​ ≈ 0.3333 Driving forces:

Soil active thrust: P a 1 = 1 2 γ H 2 K a = 1 2 ( 18.0 ) ( 6.0 ) 2 ( 1 / 3 ) = 108.0 kN/m P_{a1} = \frac{1}{2} \gamma H^2 K_a = \frac{1}{2} (18.0) (6.0)^2 (1/3) = 108.0\text{ kN/m} P a 1 ​ = 2 1 ​ γ H 2 K a ​ = 2 1 ​ ( 18.0 ) ( 6.0 ) 2 ( 1/3 ) = 108.0 kN/m , acting at y 1 = 6.0 / 3 = 2.0 m y_1 = 6.0/3 = 2.0\text{ m} y 1 ​ = 6.0/3 = 2.0 m .

Surcharge thrust: P a 2 = q K a H = ( 20.0 ) ( 1 / 3 ) ( 6.0 ) = 40.0 kN/m P_{a2} = q K_a H = (20.0) (1/3) (6.0) = 40.0\text{ kN/m} P a 2 ​ = q K a ​ H = ( 20.0 ) ( 1/3 ) ( 6.0 ) = 40.0 kN/m , acting at y 2 = 6.0 / 2 = 3.0 m y_2 = 6.0/2 = 3.0\text{ m} y 2 ​ = 6.0/2 = 3.0 m . P h = 108.0 + 40.0 = 148.0 kN/m P_h = 108.0 + 40.0 = 148.0\text{ kN/m} P h ​ = 108.0 + 40.0 = 148.0 kN/m M O = ( 108.0 × 2.0 ) + ( 40.0 × 3.0 ) = 216.0 + 120.0 = 336.0 kN ⋅ m/m M_O = (108.0 \times 2.0) + (40.0 \times 3.0) = 216.0 + 120.0 = 336.0\text{ kN}\cdot\text{m/m} M O ​ = ( 108.0 × 2.0 ) + ( 40.0 × 3.0 ) = 216.0 + 120.0 = 336.0 kN ⋅ m/m

Step 2: Compute Vertical Weights and Resisting Moments about Toe Stem height = 6.0 − 0.6 = 5.4 m 6.0 - 0.6 = 5.4\text{ m} 6.0 − 0.6 = 5.4 m .

Component Force V V V (kN/m) Moment Arm from Toe x x x (m) Moment M R = V ⋅ x M_R = V \cdot x M R ​ = V ⋅ x (kN·m/m)

1. Base Slab ( 3.5 ) ( 0.6 ) ( 24.0 ) = 50.40 (3.5)(0.6)(24.0) = 50.40 ( 3.5 ) ( 0.6 ) ( 24.0 ) = 50.40 3.5 / 2 = 1.75 3.5 / 2 = 1.75 3.5/2 = 1.75 88.20 88.20 88.20

2. Concrete Stem ( 0.4 ) ( 5.4 ) ( 24.0 ) = 51.84 (0.4)(5.4)(24.0) = 51.84 ( 0.4 ) ( 5.4 ) ( 24.0 ) = 51.84 0.8 + 0.4 / 2 = 1.00 0.8 + 0.4/2 = 1.00 0.8 + 0.4/2 = 1.00 51.84 51.84 51.84

3. Soil over Heel ( 2.3 ) ( 5.4 ) ( 18.0 ) = 223.56 (2.3)(5.4)(18.0) = 223.56 ( 2.3 ) ( 5.4 ) ( 18.0 ) = 223.56 0.8 + 0.4 + 2.3 / 2 = 2.35 0.8 + 0.4 + 2.3/2 = 2.35 0.8 + 0.4 + 2.3/2 = 2.35 525.37 525.37 525.37

4. Surcharge over Heel ( 20.0 ) ( 2.3 ) = 46.00 (20.0)(2.3) = 46.00 ( 20.0 ) ( 2.3 ) = 46.00 2.35 2.35 2.35 108.10 108.10 108.10

Total ∑ V = 371.80 kN/m \sum V = 371.80\text{ kN/m} ∑ V = 371.80 kN/m ∑ M R = 773.51 kN ⋅ m/m \sum M_R = 773.51\text{ kN}\cdot\text{m/m} ∑ M R ​ = 773.51 kN ⋅ m/m

Step 3: Check Overturning Factor of Safety F S o t = ∑ M R M O = 773.51 336.0 = 2.30 ≥ 2.0 ( S A F E ) FS_{ot} = \frac{\sum M_R}{M_O} = \frac{773.51}{336.0} = 2.30 \ge 2.0 \quad (\mathbf{SAFE}) F S o t ​ = M O ​ ∑ M R ​ ​ = 336.0 773.51 ​ = 2.30 ≥ 2.0 ( SAFE )

Step 4: Check Resultant Location and Base Contact Pressure x ˉ = ∑ M R − M O ∑ V = 773.51 − 336.0 371.80 = 437.51 371.80 = 1.1767 m from toe \bar{x} = \frac{\sum M_R - M_O}{\sum V} = \frac{773.51 - 336.0}{371.80} = \frac{437.51}{371.80} = 1.1767\text{ m from toe} x ˉ = ∑ V ∑ M R ​ − M O ​ ​ = 371.80 773.51 − 336.0 ​ = 371.80 437.51 ​ = 1.1767 m from toe e = B 2 − x ˉ = 3.5 2 − 1.1767 = 1.75 − 1.1767 = 0.5733 m e = \frac{B}{2} - \bar{x} = \frac{3.5}{2} - 1.1767 = 1.75 - 1.1767 = 0.5733\text{ m} e = 2 B ​ − x ˉ = 2 3.5 ​ − 1.1767 = 1.75 − 1.1767 = 0.5733 m Check middle-third kern limit: B 6 = 3.5 6 = 0.5833 m \frac{B}{6} = \frac{3.5}{6} = 0.5833\text{ m} 6 B ​ = 6 3.5 ​ = 0.5833 m Since e = 0.5733 m ≤ 0.5833 m e = 0.5733\text{ m} \le 0.5833\text{ m} e = 0.5733 m ≤ 0.5833 m , the resultant lies within the middle third (no tensile detachment at heel). q max ⁡ = ∑ V B ( 1 + 6 e B ) = 371.80 3.5 ( 1 + 6 ( 0.5733 ) 3.5 ) = 106.23 ( 1 + 0.9828 ) = 210.63 kPa ≈ 210.6 kPa q_{\max} = \frac{\sum V}{B} \left( 1 + \frac{6e}{B} \right) = \frac{371.80}{3.5} \left( 1 + \frac{6(0.5733)}{3.5} \right) = 106.23 (1 + 0.9828) = 210.63\text{ kPa} \approx 210.6\text{ kPa} q m a x ​ = B ∑ V ​ ( 1 + B 6 e ​ ) = 3.5 371.80 ​ ( 1 + 3.5 6 ( 0.5733 ) ​ ) = 106.23 ( 1 + 0.9828 ) = 210.63 kPa ≈ 210.6 kPa q min ⁡ = 106.23 ( 1 − 0.9828 ) = 1.83 kPa ≥ 0 q_{\min} = 106.23 (1 - 0.9828) = 1.83\text{ kPa} \ge 0 q m i n ​ = 106.23 ( 1 − 0.9828 ) = 1.83 kPa ≥ 0

CELE Board Exam Traps & Strategic Checklists

Warning

Tension Crack Water Thrust: If a cohesive backfill develops tension cracks to depth z c z_c z c ​ and is subsequently flooded by rain, remember to add the full hydrostatic water triangle P w = 1 2 γ w z c 2 P_w = \frac{1}{2} \gamma_w z_c^2 P w ​ = 2 1 ​ γ w ​ z c 2 ​ acting within the crack. This water force creates a massive sudden overturning moment.

Surcharge Weight on Heel: When a uniform surcharge q q q is present, do not forget to include the downward vertical weight of that surcharge acting directly over the heel width ( W q , heel = q × L heel W_{q,\text{heel}} = q \times L_{\text{heel}} W q , heel ​ = q × L heel ​ ) as a stabilizing vertical force and resisting moment.

Middle-Third Kern Violation ( e > B / 6 e > B/6 e > B /6 ): If eccentricity exceeds B / 6 B/6 B /6 , soil cannot take tension. The contact pressure becomes triangular over an effective width 3 x ˉ 3\bar{x} 3 x ˉ , yielding q max ⁡ = 2 ∑ V 3 x ˉ q_{\max} = \frac{2 \sum V}{3\bar{x}} q m a x ​ = 3 x ˉ 2 ∑ V ​ . Never use the standard formula ∑ V B ( 1 + 6 e / B ) \frac{\sum V}{B}(1 + 6e/B) B ∑ V ​ ( 1 + 6 e / B ) if e > B / 6 e > B/6 e > B /6 .

Loading diagram... Retaining Wall Force Equilibrium and Contact Stress Distribution