Study guide

10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria

PRC Civil Engineer Licensure Examination CELE

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Examination Overview, RA 544 & Professional Practice

1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice

2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics

2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum

3 Chapter 3: Engineering Data Analysis & Engineering Economy

3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis

4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying

4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves

5 Chapter 5: Highway & Transportation Engineering

5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems

6 Chapter 6: Construction Materials, Methods, Management & Safety

6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical

7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy

7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses

8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply

8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment

9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass

9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement

10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations

10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability

11 Chapter 11: Engineering Mechanics & Statics

11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members

12 Chapter 12: Strength of Materials

12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle

13 Chapter 13: Structural Analysis & NSCP Load Criteria

13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake

14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)

14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design

15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing

15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning

10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria

Key Takeaways Explain This Topic AI

Soil shear strength is governed by the Mohr-Coulomb criterion, defined in effective stress terms as τf = c' + σ' tan φ', where c' is effective cohesion and φ' is the effective angle of internal friction.

At failure, the principal stresses satisfy the critical transformation σ'1 = σ'3 tan²(45° + φ'/2) + 2c' tan(45° + φ'/2), establishing the flow value Nφ = tan²(45° + φ'/2).

The theoretical failure plane is inclined at an angle θ = 45° + φ'/2 with respect to the major principal plane (the plane acting perpendicular to σ'1).

Triaxial shear testing differentiates between Consolidated-Drained (CD), Consolidated-Undrained (CU), and Unconsolidated-Undrained (UU) states; the UU test yields undrained shear strength su = cu = (σ1 - σ3)/2 under a φ = 0 condition.

In-situ shear strength is field-verified via Vane Shear Testing (cu = T / [π D² (H/2 + D/6)]) for soft cohesive clays, and Standard Penetration Testing (SPT N-value corrected to N60 and (N1)60) for cohesionless strata.

Last updated: October 2026

10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria

The shear strength of a soil mass represents its internal resistance per unit area to sliding or slippage along an internal plane. Foundation bearing capacity failure, retaining wall collapse, and slope instability are fundamentally shear failures —soil rarely fails under direct compression, but rather shears when internal shear stresses exceed available shear resistance.

The Mohr-Coulomb Failure Criterion

In 1900, Christian Otto Mohr combined Coulomb's frictional model with stress transformation theory to formulate the classical Mohr-Coulomb failure criterion .

Total vs. Effective Stress Envelopes

Because soil shearing resistance is transmitted through interparticle mineral contact points, shear strength must be analyzed in terms of effective stresses :

Effective Stress Formulation (Drained / Long-Term): τ f = c ′ + σ ′ tan ⁡ ϕ ′ = c ′ + ( σ − u ) tan ⁡ ϕ ′ \tau_f = c' + \sigma' \tan \phi' = c' + (\sigma - u) \tan \phi' τ f ​ = c ′ + σ ′ tan ϕ ′ = c ′ + ( σ − u ) tan ϕ ′ Where:

  • τ f \tau_f τ f ​ = shear strength on the failure plane
  • c ′ c' c ′ = effective cohesion (apparent interparticle bonding or cementation)
  • σ ′ \sigma' σ ′ = effective normal stress on the failure plane ( = σ − u = \sigma - u = σ − u )

ϕ ′ \phi' ϕ ′ = effective angle of internal friction (shearing resistance from particle interlock and friction)

u u u = pore water pressure

Total Stress Formulation (Undrained / Short-Term): τ f = c u + σ tan ⁡ ϕ u \tau_f = c_u + \sigma \tan \phi_u τ f ​ = c u ​ + σ tan ϕ u ​ For fully saturated cohesive soils subjected to rapid undrained loading, ϕ u = 0 \phi_u = 0 ϕ u ​ = 0 , giving: τ f = c u = s u \tau_f = c_u = s_u τ f ​ = c u ​ = s u ​ Where c u c_u c u ​ (or s u s_u s u ​ ) is the undrained shear strength . Shear Stress (τ)

  • ^
  • | / Mohr-Coulomb Failure Envelope
  • | / τ = c' + σ' tan(φ')
  • | ---*---

| .-' | '-.

| .' | '.

  • | / | \
  • | ; | ;
  • | | Mohr's Circle |
  • | ; at Failure ;
  • | \ /
  • | '. .'
  • | '-. .-'
  • | c' '---------'
  • |----+-------------------|-----------|-----------------> Effective Normal
  • 0 σ'3 σ'1 Stress (σ')
  • Principal Stresses at Failure

From the geometric relationship between Mohr's circle of stress and its tangent failure envelope, a fundamental relationship connects major principal stress σ 1 ′ \sigma'_1 σ 1 ′ ​ and minor principal stress σ 3 ′ \sigma'_3 σ 3 ′ ​ at failure: σ 1 ′ = σ 3 ′ tan ⁡ 2 ( 45 ∘ + ϕ ′ 2 ) + 2 c ′ tan ⁡ ( 45 ∘ + ϕ ′ 2 ) \sigma'_1 = \sigma'_3 \tan^2\left(45^\circ + \frac{\phi'}{2}\right) + 2 c' \tan\left(45^\circ + \frac{\phi'}{2}\right) σ 1 ′ ​ = σ 3 ′ ​ tan 2 ( 4 5 ∘ + 2 ϕ ′ ​ ) + 2 c ′ tan ( 4 5 ∘ + 2 ϕ ′ ​ )

Defining the flow value (passive pressure factor) N ϕ N_\phi N ϕ ​ : N ϕ = tan ⁡ 2 ( 45 ∘ + ϕ ′ 2 ) = 1 + sin ⁡ ϕ ′ 1 − sin ⁡ ϕ ′ N_\phi = \tan^2\left(45^\circ + \frac{\phi'}{2}\right) = \frac{1 + \sin \phi'}{1 - \sin \phi'} N ϕ ​ = tan 2 ( 4 5 ∘ + 2 ϕ ′ ​ ) = 1 − s i n ϕ ′ 1 + s i n ϕ ′ ​ σ 1 ′ = σ 3 ′ N ϕ + 2 c ′ N ϕ \sigma'_1 = \sigma'_3 N_\phi + 2 c' \sqrt{N_\phi} σ 1 ′ ​ = σ 3 ′ ​ N ϕ ​ + 2 c ′ N ϕ ​ ​

For clean, cohesionless soils ( c ′ = 0 c' = 0 c ′ = 0 , such as sands and gravels): σ 1 ′ = σ 3 ′ tan ⁡ 2 ( 45 ∘ + ϕ ′ 2 ) ⟹ σ 1 ′ σ 3 ′ = 1 + sin ⁡ ϕ ′ 1 − sin ⁡ ϕ ′ \sigma'_1 = \sigma'_3 \tan^2\left(45^\circ + \frac{\phi'}{2}\right) \implies \frac{\sigma'_1}{\sigma'_3} = \frac{1 + \sin \phi'}{1 - \sin \phi'} σ 1 ′ ​ = σ 3 ′ ​ tan 2 ( 4 5 ∘ + 2 ϕ ′ ​ ) ⟹ σ 3 ′ ​ σ 1 ′ ​ ​ = 1 − s i n ϕ ′ 1 + s i n ϕ ′ ​

Orientation of the Failure Plane

Mohr's circle transformation demonstrates that the failure plane does not align with the plane of maximum shear stress (which occurs at 45 ∘ 45^\circ 4 5 ∘ ). Instead, because shear resistance increases with normal stress, failure occurs on a critical plane where the ratio of shear stress to shear strength is maximized.

The failure plane is inclined at an angle θ \theta θ to the major principal plane (the plane upon which σ 1 ′ \sigma'_1 σ 1 ′ ​ acts, typically the horizontal plane in standard compression tests): θ = 45 ∘ + ϕ ′ 2 \theta = 45^\circ + \frac{\phi'}{2} θ = 4 5 ∘ + 2 ϕ ′ ​

The angle made by the failure plane with the direction of major principal stress σ 1 ′ \sigma'_1 σ 1 ′ ​ is: α = 90 ∘ − θ = 45 ∘ − ϕ ′ 2 \alpha = 90^\circ - \theta = 45^\circ - \frac{\phi'}{2} α = 9 0 ∘ − θ = 4 5 ∘ − 2 ϕ ′ ​

The normal and shear stresses acting on this failure plane are calculated directly: σ f ′ = σ 1 ′ + σ 3 ′ 2 + σ 1 ′ − σ 3 ′ 2 cos ⁡ ( 2 θ ) \sigma'_f = \frac{\sigma'_1 + \sigma'_3}{2} + \frac{\sigma'_1 - \sigma'_3}{2} \cos(2\theta) σ f ′ ​ = 2 σ 1 ′ ​ + σ 3 ′ ​ ​ + 2 σ 1 ′ ​ − σ 3 ′ ​ ​ cos ( 2 θ ) τ f = σ 1 ′ − σ 3 ′ 2 sin ⁡ ( 2 θ ) \tau_f = \frac{\sigma'_1 - \sigma'_3}{2} \sin(2\theta) τ f ​ = 2 σ 1 ′ ​ − σ 3 ′ ​ ​ sin ( 2 θ )

Laboratory Shear Testing Methods

Four standard laboratory test configurations determine soil shear strength parameters:

1. Direct Shear Test (ASTM D3080)

Soil is placed inside a horizontally split metal shear box. A constant normal force N N N is applied vertically, while a horizontal shear force T T T is applied to displace the lower box half until the soil shears.

Advantages: Rapid, inexpensive, simple setup; excellent for clean cohesionless sands and gravels.

Disadvantages: Failure plane is artificially forced along a pre-determined horizontal plane; non-uniform stress distribution at edges; drainage cannot be controlled for fine clays; pore water pressure cannot be measured.

Failure criterion: τ f = T max ⁡ / A \tau_f = T_{\max} / A τ f ​ = T m a x ​ / A plotted against σ ′ = N / A \sigma' = N / A σ ′ = N / A .

2. Unconfined Compression Test (UCT, ASTM D2166)

A special case of the triaxial test where the specimen has no lateral confinement (confining cell pressure σ 3 = 0 \sigma_3 = 0 σ 3 ​ = 0 ). Only applicable to cohesive, saturated fine-grained soils.

Axial load is increased rapidly until the cylindrical sample fails at axial stress q u q_u q u ​ (the unconfined compressive strength ).

Because σ 3 = 0 \sigma_3 = 0 σ 3 ​ = 0 and ϕ = 0 \phi = 0 ϕ = 0 , the diameter of Mohr's circle equals q u q_u q u ​ : c u = s u = q u 2 c_u = s_u = \frac{q_u}{2} c u ​ = s u ​ = 2 q u ​ ​

3. Triaxial Shear Tests (ASTM D2850 / D4767)

The gold standard of geotechnical testing. A cylindrical specimen encased in a thin rubber membrane is placed inside a pressurized fluid chamber. Testing occurs in two stages: Stage 1 (Confining Stage) where cell fluid pressure σ 3 \sigma_3 σ 3 ​ is applied; and Stage 2 (Shearing Stage) where an axial deviator stress Δ σ d = σ 1 − σ 3 \Delta \sigma_d = \sigma_1 - \sigma_3 Δ σ d ​ = σ 1 ​ − σ 3 ​ is applied to cause shear failure.

Test Designation Drainage During Consolidation (Stage 1) Drainage During Shearing (Stage 2) Parameters Obtained Field Application Mimicked

Consolidated-Drained (CD) Open (specimen consolidates under σ 3 \sigma_3 σ 3 ​ ) Open (very slow shearing, Δ u = 0 \Delta u = 0 Δ u = 0 ) Drained parameters c ′ , ϕ ′ c', \phi' c ′ , ϕ ′ Long-term slope stability, fully drained excavations

Consolidated-Undrained (CU) Open (specimen consolidates under σ 3 \sigma_3 σ 3 ​ ) Closed (fast shearing, pore pressure Δ u \Delta u Δ u measured) Both total ( c , ϕ c, \phi c , ϕ ) and effective ( c ′ , ϕ ′ c', \phi' c ′ , ϕ ′ ) parameters Rapid drawdown of reservoirs, rapid loading after consolidation

Unconsolidated-Undrained (UU) Closed (no consolidation under σ 3 \sigma_3 σ 3 ​ ) Closed (rapid shearing, no drainage) Undrained strength c u c_u c u ​ ( ϕ u = 0 \phi_u = 0 ϕ u ​ = 0 ) End-of-construction stability for embankments on soft clay

Skempton's Pore Pressure Parameters

In undrained triaxial shearing, pore water pressure response is quantified by Skempton's coefficients A A A and B B B : Δ u = B [ Δ σ 3 + A ( Δ σ 1 − Δ σ 3 ) ] \Delta u = B [ \Delta \sigma_3 + A (\Delta \sigma_1 - \Delta \sigma_3) ] Δ u = B [ Δ σ 3 ​ + A ( Δ σ 1 ​ − Δ σ 3 ​ )]

Parameter B B B : Governs the confining stage. For fully saturated soils ( S = 100 % S = 100\% S = 100% ), water is virtually incompressible relative to the soil skeleton, yielding B = 1.0 B = 1.0 B = 1.0 . For dry soils, B = 0 B = 0 B = 0 .

Parameter A A A : Governs the deviator shearing stage. At failure ( A f A_f A f ​ ):

Normally consolidated soft clays: A f = + 0.5 to + 1.0 A_f = +0.5 \text{ to } +1.0 A f ​ = + 0.5 to + 1.0 (contractive tendency, positive pore pressure buildup).

Heavily overconsolidated clays and dense sands: A f = − 0.5 to 0 A_f = -0.5 \text{ to } 0 A f ​ = − 0.5 to 0 (dilatant tendency, negative pore pressure / suction).

Field In-Situ Shear Testing

Because laboratory specimens suffer from disturbance during drilling, extraction, transport, and trimming, in-situ field testing is essential for sensitive deposits.

1. Field Vane Shear Test (VST, ASTM D2573)

A four-bladed cruciform metal vane is pressed into undisturbed cohesive soil at the bottom of a borehole and rotated at a standard rate ( 0.1 ∘ / s 0.1^\circ/\text{s} 0. 1 ∘ / s ) until a cylindrical shear surface fails. | | Drive Rod

  • | |
  • +--+-+--+
  • | | | |
  • | | | |
  • H | | | | Vane Height (H = 2D standard)
  • | | | |
  • +--+-+--+
  • <-D-> Vane Diameter (D)

The maximum torque T T T mobilizes shear resistance along the cylindrical perimeter (area π D H \pi D H π DH ) and the two circular flat ends (top and bottom): T = T side + 2 T end = ( c u π D H ) ( D 2 ) + 2 ∫ 0 D / 2 c u ( 2 π r d r ) r = c u π D 2 ( H 2 + D 6 ) T = T_{\text{side}} + 2 T_{\text{end}} = (c_u \pi D H) \left(\frac{D}{2}\right) + 2 \int_0^{D/2} c_u (2\pi r\,dr) r = c_u \pi D^2 \left( \frac{H}{2} + \frac{D}{6} \right) T = T side ​ + 2 T end ​ = ( c u ​ π DH ) ( 2 D ​ ) + 2 ∫ 0 D /2 ​ c u ​ ( 2 π r d r ) r = c u ​ π D 2 ( 2 H ​ + 6 D ​ )

Solving for undrained shear strength c u c_u c u ​ : c u = T π D 2 ( H 2 + D 6 ) c_u = \frac{T}{\pi D^2 \left( \frac{H}{2} + \frac{D}{6} \right)} c u ​ = π D 2 ( 2 H ​ + 6 D ​ ) T ​

For a standard rectangular vane where H = 2 D H = 2D H = 2 D : c u = T π D 2 ( D + D 6 ) = 6 T 7 π D 3 c_u = \frac{T}{\pi D^2 \left( D + \frac{D}{6} \right)} = \frac{6 T}{7 \pi D^3} c u ​ = π D 2 ( D + 6 D ​ ) T ​ = 7 π D 3 6 T ​

Note

Field vane shear values overestimate true field strength in plastic clays. Bjerrum's correction factor ( λ \lambda λ ) is applied for design: c u , design = λ c u , vane c_{u,\text{design}} = \lambda c_{u,\text{vane}} c u , design ​ = λ c u , vane ​ , where λ = 1.7 − 0.54 log ⁡ 10 ( P I ) \lambda = 1.7 - 0.54 \log_{10}(PI) λ = 1.7 − 0.54 lo g 10 ​ ( P I ) , and P I PI P I is the Plasticity Index.

2. Standard Penetration Test (SPT, ASTM D1586)

A standard split-spoon sampler ( 50.8 mm 50.8\text{ mm} 50.8 mm OD, 34.9 mm 34.9\text{ mm} 34.9 mm ID) is driven into the bottom of a borehole using a 140 lb 140\text{ lb} 140 lb ( 63.5 kg 63.5\text{ kg} 63.5 kg ) safety or donut hammer dropping freely from a height of 30 in 30\text{ in} 30 in ( 760 mm 760\text{ mm} 760 mm ).

The sampler is driven through three consecutive 6 -in 6\text{-in} 6 -in ( 150 mm 150\text{ mm} 150 mm ) intervals.

The first 6 inches is discarded as the seating drive.

The SPT N N N -value is the sum of blows required for the second and third 6-inch intervals (blows per foot of penetration).

To account for equipment variations and depth, the raw field N N N -value is normalized: N 60 = N ⋅ η H ⋅ η B ⋅ η S ⋅ η R 60 N_{60} = \frac{N \cdot \eta_H \cdot \eta_B \cdot \eta_S \cdot \eta_R}{60} N 60 ​ = 60 N ⋅ η H ​ ⋅ η B ​ ⋅ η S ​ ⋅ η R ​ ​ Where η H \eta_H η H ​ is hammer efficiency (safety hammer ≈ 60 % \approx 60\% ≈ 60% , automatic trip hammer ≈ 80 % \approx 80\% ≈ 80% ), η B \eta_B η B ​ is borehole diameter correction, η S \eta_S η S ​ is sampler lining correction, and η R \eta_R η R ​ is rod length correction.

Correcting for effective overburden stress σ 0 ′ \sigma'_0 σ 0 ′ ​ yields ( N 1 ) 60 (N_1)_{60} ( N 1 ​ ) 60 ​ : ( N 1 ) 60 = C N N 60 = p a σ 0 ′ N 60 ≤ 2.0 N 60 (N_1)_{60} = C_N N_{60} = \sqrt{\frac{p_a}{\sigma'_0}} N_{60} \le 2.0 N_{60} ( N 1 ​ ) 60 ​ = C N ​ N 60 ​ = σ 0 ′ ​ p a ​ ​ ​ N 60 ​ ≤ 2.0 N 60 ​ Where p a = 100 kPa ≈ 1 atm p_a = 100\text{ kPa} \approx 1\text{ atm} p a ​ = 100 kPa ≈ 1 atm is reference atmospheric pressure (Liao & Whitman formula).

  • Step-by-Step Worked Problem Examples
  • Worked Example: Consolidated-Undrained (CU) Triaxial Test Analysis

Problem: A consolidated-undrained (CU) triaxial compression test was performed on a saturated normally consolidated clay specimen ( c ′ = 0 c' = 0 c ′ = 0 ). The confining cell pressure was maintained at σ 3 = 150 kPa \sigma_3 = 150\text{ kPa} σ 3 ​ = 150 kPa . At failure, the deviator stress reached Δ σ d = 180 kPa \Delta \sigma_d = 180\text{ kPa} Δ σ d ​ = 180 kPa , and the induced pore water pressure was measured to be u f = 60 kPa u_f = 60\text{ kPa} u f ​ = 60 kPa .

Calculate the effective principal stresses at failure ( σ 3 ′ \sigma'_3 σ 3 ′ ​ and σ 1 ′ \sigma'_1 σ 1 ′ ​ ).

Determine the effective angle of internal friction ϕ ′ \phi' ϕ ′ .

Determine the theoretical failure plane angle θ \theta θ with respect to the major principal plane.

Compute the effective normal stress σ f ′ \sigma'_f σ f ′ ​ and shear stress τ f \tau_f τ f ​ acting on the failure plane.

Solution:

Step 1: Compute Total and Effective Principal Stresses σ 3 = 150 kPa \sigma_3 = 150\text{ kPa} σ 3 ​ = 150 kPa σ 1 = σ 3 + Δ σ d = 150 + 180 = 330 kPa \sigma_1 = \sigma_3 + \Delta \sigma_d = 150 + 180 = 330\text{ kPa} σ 1 ​ = σ 3 ​ + Δ σ d ​ = 150 + 180 = 330 kPa Apply Terzaghi's effective stress principle ( u f = 60 kPa u_f = 60\text{ kPa} u f ​ = 60 kPa ): σ 3 ′ = σ 3 − u f = 150 − 60 = 90 kPa \sigma'_3 = \sigma_3 - u_f = 150 - 60 = 90\text{ kPa} σ 3 ′ ​ = σ 3 ​ − u f ​ = 150 − 60 = 90 kPa σ 1 ′ = σ 1 − u f = 330 − 60 = 270 kPa \sigma'_1 = \sigma_1 - u_f = 330 - 60 = 270\text{ kPa} σ 1 ′ ​ = σ 1 ​ − u f ​ = 330 − 60 = 270 kPa

Step 2: Calculate Effective Friction Angle ( ϕ ′ \phi' ϕ ′ ) For a normally consolidated clay, effective cohesion c ′ = 0 c' = 0 c ′ = 0 . Using the principal stress ratio relation: sin ⁡ ϕ ′ = σ 1 ′ − σ 3 ′ σ 1 ′ + σ 3 ′ = 270 − 90 270 + 90 = 180 360 = 0.500 \sin \phi' = \frac{\sigma'_1 - \sigma'_3}{\sigma'_1 + \sigma'_3} = \frac{270 - 90}{270 + 90} = \frac{180}{360} = 0.500 sin ϕ ′ = σ 1 ′ ​ + σ 3 ′ ​ σ 1 ′ ​ − σ 3 ′ ​ ​ = 270 + 90 270 − 90 ​ = 360 180 ​ = 0.500 ϕ ′ = arcsin ⁡ ( 0.500 ) = 30.0 ∘ \phi' = \arcsin(0.500) = 30.0^\circ ϕ ′ = arcsin ( 0.500 ) = 30. 0 ∘

Step 3: Determine Failure Plane Orientation ( θ \theta θ ) The failure plane angle with the major principal (horizontal) plane is: θ = 45 ∘ + ϕ ′ 2 = 45 ∘ + 30.0 ∘ 2 = 45 ∘ + 15 ∘ = 60.0 ∘ \theta = 45^\circ + \frac{\phi'}{2} = 45^\circ + \frac{30.0^\circ}{2} = 45^\circ + 15^\circ = 60.0^\circ θ = 4 5 ∘ + 2 ϕ ′ ​ = 4 5 ∘ + 2 30. 0 ∘ ​ = 4 5 ∘ + 1 5 ∘ = 60. 0 ∘

Step 4: Compute Stresses on the Failure Plane σ f ′ = σ 1 ′ + σ 3 ′ 2 + σ 1 ′ − σ 3 ′ 2 cos ⁡ ( 2 θ ) \sigma'_f = \frac{\sigma'_1 + \sigma'_3}{2} + \frac{\sigma'_1 - \sigma'_3}{2} \cos(2\theta) σ f ′ ​ = 2 σ 1 ′ ​ + σ 3 ′ ​ ​ + 2 σ 1 ′ ​ − σ 3 ′ ​ ​ cos ( 2 θ ) σ f ′ = 270 + 90 2 + 270 − 90 2 cos ⁡ ( 120 ∘ ) = 180 + 90 ( − 0.5 ) = 180 − 45 = 135.0 kPa \sigma'_f = \frac{270 + 90}{2} + \frac{270 - 90}{2} \cos(120^\circ) = 180 + 90(-0.5) = 180 - 45 = 135.0\text{ kPa} σ f ′ ​ = 2 270 + 90 ​ + 2 270 − 90 ​ cos ( 12 0 ∘ ) = 180 + 90 ( − 0.5 ) = 180 − 45 = 135.0 kPa τ f = σ 1 ′ − σ 3 ′ 2 sin ⁡ ( 2 θ ) = 270 − 90 2 sin ⁡ ( 120 ∘ ) = 90 × 3 2 = 77.94 kPa \tau_f = \frac{\sigma'_1 - \sigma'_3}{2} \sin(2\theta) = \frac{270 - 90}{2} \sin(120^\circ) = 90 \times \frac{\sqrt{3}}{2} = 77.94\text{ kPa} τ f ​ = 2 σ 1 ′ ​ − σ 3 ′ ​ ​ sin ( 2 θ ) = 2 270 − 90 ​ sin ( 12 0 ∘ ) = 90 × 2 3 ​ ​ = 77.94 kPa Check with Mohr-Coulomb equation: τ f = σ f ′ tan ⁡ ϕ ′ = 135.0 tan ⁡ ( 30 ∘ ) = 135.0 × 0.57735 = 77.94 kPa ( Matches perfectly! ) \tau_f = \sigma'_f \tan \phi' = 135.0 \tan(30^\circ) = 135.0 \times 0.57735 = 77.94\text{ kPa} \quad (\text{Matches perfectly!}) τ f ​ = σ f ′ ​ tan ϕ ′ = 135.0 tan ( 3 0 ∘ ) = 135.0 × 0.57735 = 77.94 kPa ( Matches perfectly! )

CELE Board Exam Traps & Strategic Checklists

Warning

Deviator Stress vs. Major Principal Stress: The problem statement often provides "deviator stress at failure Δ σ d = 180 kPa \Delta \sigma_d = 180\text{ kPa} Δ σ d ​ = 180 kPa ". Do not mistake this for σ 1 \sigma_1 σ 1 ​ ! The major principal stress is σ 1 = σ 3 + Δ σ d \sigma_1 = \sigma_3 + \Delta \sigma_d σ 1 ​ = σ 3 ​ + Δ σ d ​ .

Unconfined Compressive Strength vs. Cohesion: q u q_u q u ​ is the diameter of Mohr's circle, whereas c u c_u c u ​ is the radius . Always remember: c u = q u / 2 c_u = q_u / 2 c u ​ = q u ​ /2 . Board problems regularly place q u q_u q u ​ as a distractor to catch examinees who forget the factor of 2.

Failure Plane Reference Axis: Read carefully whether the failure plane angle is requested relative to the major principal plane ( θ = 45 ∘ + ϕ / 2 \theta = 45^\circ + \phi/2 θ = 4 5 ∘ + ϕ /2 ) or relative to the direction of major principal stress ( α = 45 ∘ − ϕ / 2 \alpha = 45^\circ - \phi/2 α = 4 5 ∘ − ϕ /2 ). They are complementary angles.

Loading diagram... Mohr's Circle of Stress Transformation and Failure Envelope Mechanics