Study guide
5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design
Key Takeaways Explain This Topic AI
The fundamental macroscopic relationship of traffic flow is q = u ⋅ k q = u \cdot k q = u ⋅ k , relating traffic flow rate ( q q q , veh/h), space-mean speed ( u u u , km/h), and traffic density ( k k k , veh/km).
Space-mean speed ( u s = n / ∑ ( 1 / v i ) u_s = n / \sum(1/v_i) u s = n / ∑ ( 1/ v i ) ) is the harmonic mean of spot speeds and represents true spatial travel velocity, which is always less than or equal to time-mean speed ( u t = ∑ v i / n u_t = \sum v_i / n u t = ∑ v i / n ) per Wardrop's formula: u t = u s + σ s 2 u s u_t = u_s + \frac{\sigma_s^2}{u_s} u t = u s + u s σ s 2 .
Under Greenshields linear model ( u = u f ( 1 − k / k j ) u = u_f(1 - k/k_j) u = u f ( 1 − k / k j ) ), maximum roadway capacity occurs at critical density k c = k j / 2 k_c = k_j/2 k c = k j /2 and critical speed u c = u f / 2 u_c = u_f/2 u c = u f /2 , resulting in a peak capacity q max = u f k j 4 q_{\max} = \frac{u_f k_j}{4} q m a x = 4 u f k j .
Highway operational quality is evaluated across six Levels of Service (LOS A through F) based on flow rate, volume-to-capacity ( v / c v/c v / c ) ratio, travel speed, and vehicle freedom to maneuver.
Flexible pavements transmit traffic loads through layered structural action governed by the AASHTO Structural Number ( SN = a 1 D 1 + a 2 D 2 m 2 + a 3 D 3 m 3 \text{SN} = a_1 D_1 + a_2 D_2 m_2 + a_3 D_3 m_3 SN = a 1 D 1 + a 2 D 2 m 2 + a 3 D 3 m 3 ) calibrated to 18-kip (80 kN) ESALs, whereas rigid pavements utilize high-modulus concrete slabs with smooth dowel bars transferring joint shear.
Last updated: October 2026
5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design
Traffic stream characteristics and pavement structural design form the analytical core of transportation engineering in the CELE syllabus. Traffic engineering evaluates the macroscopic interactions of vehicles traversing roadway facilities, establishing highway capacity and Level of Service (LOS). Pavement engineering designs structural layers capable of withstanding millions of repetitive heavy vehicular wheel loads over multi-decade design lives without excessive fatigue cracking or rutting.
Traffic Stream Variables & Fundamental Relations
Macroscopic traffic flow theory describes vehicular movement using three continuous stream variables:
Flow Rate ( q q q ): The number of vehicles passing a designated cross-section of a roadway per unit time, conventionally expressed in vehicles per hour (veh/h) or passenger cars per hour (pc/h): q = N T = 3600 h ˉ t q = \frac{N}{T} = \frac{3600}{\bar{h}_t} q = T N = h ˉ t 3600 Where h ˉ t \bar{h}_t h ˉ t is the average time headway (seconds between successive front vehicle bumpers).
Density ( k k k ): The number of vehicles occupying a unit length of roadway lane at a given instant, conventionally expressed in vehicles per kilometer (veh/km): k = N L = 1000 s ˉ k = \frac{N}{L} = \frac{1000}{\bar{s}} k = L N = s ˉ 1000 Where s ˉ \bar{s} s ˉ is the average space headway or vehicle spacing (meters between front bumpers).
Speed ( u u u ): The rate of vehicle movement, expressed in kilometers per hour (km/h).
The Fundamental Equation of Traffic Flow
Through dimensional analysis and continuity of mass:
q = u ⋅ k q = u \cdot k q = u ⋅ k [ vehicles hour ] = [ kilometers hour ] × [ vehicles kilometer ] \left[ \frac{\text{vehicles}}{\text{hour}} \right] = \left[ \frac{\text{kilometers}}{\text{hour}} \right] \times \left[ \frac{\text{vehicles}}{\text{kilometer}} \right] [ hour vehicles ] = [ hour kilometers ] × [ kilometer vehicles ]
Important
The fundamental equation q = u ⋅ k q = u \cdot k q = u ⋅ k holds strictly only when speed u u u is evaluated as the space-mean speed ( u s u_s u s ) . Applying time-mean speed ( u t u_t u t ) violates stream continuity and consistently overestimates roadway flow rate.
Time-Mean Speed ( u t u_t u t ) vs Space-Mean Speed ( u s u_s u s )
A major conceptual topic in traffic engineering is the distinction between point-based and space-based speed measurements:
1. Time-Mean Speed ( u t u_t u t )
Time-mean speed is the arithmetic average of instantaneous vehicle spot speeds recorded by an observer or detector (e.g., radar gun or inductive loop) at a single fixed roadway cross-section over time interval T T T :
- u t = 1 n ∑ i = 1 n v i u_t = \frac{1}{n} \sum_{i=1}^{n} v_i u t = n 1 ∑ i = 1 n v i
- 2. Space-Mean Speed ( u s u_s u s )
Space-mean speed is the average speed of all vehicles occupying a designated roadway length L L L at a specific instant. Operationally, it is calculated as the total vehicle-distance divided by total vehicle-travel time, which is mathematically identical to the harmonic mean of spot speeds:
u s = n L ∑ i = 1 n t i = n ∑ i = 1 n 1 v i u_s = \frac{n L}{\sum_{i=1}^{n} t_i} = \frac{n}{\sum_{i=1}^{n} \frac{1}{v_i}} u s = ∑ i = 1 n t i n L = ∑ i = 1 n v i 1 n
Wardrop's Relationship
J.G. Wardrop established the fundamental mathematical identity linking time-mean and space-mean speed:
u t = u s + σ s 2 u s u_t = u_s + \frac{\sigma_s^2}{u_s} u t = u s + u s σ s 2
Where σ s 2 \sigma_s^2 σ s 2 is the variance of vehicle speeds about the space-mean speed:
σ s 2 = 1 n ∑ i = 1 n ( v i − u s ) 2 \sigma_s^2 = \frac{1}{n} \sum_{i=1}^{n} (v_i - u_s)^2 σ s 2 = n 1 ∑ i = 1 n ( v i − u s ) 2
Because the variance σ s 2 ≥ 0 \sigma_s^2 \ge 0 σ s 2 ≥ 0 , it is a mathematical axiom that u t ≥ u s u_t \ge u_s u t ≥ u s always . The two speed values are equal if and only if all vehicles travel at the identical speed ( σ s 2 = 0 \sigma_s^2 = 0 σ s 2 = 0 ). A fixed observer sees fast vehicles more often per hour than slow ones, while a snapshot of a road section captures slow vehicles longer. This is why the time-mean speed weights fast vehicles more heavily than the space-mean speed does.
Greenshields Macroscopic Stream Model
Introduced by Bruce Greenshields in 1935, the Greenshields model hypothesizes a linear relationship between traffic speed u u u and traffic density k k k :
u = u f ( 1 − k k j ) u = u_f \left( 1 - \frac{k}{k_j} \right) u = u f ( 1 − k j k )
Where:
- u f u_f u f = free-flow speed (km/h) as density approaches zero ( k → 0 k \to 0 k → 0 )
- k j k_j k j = jam density (veh/km) at complete standstill when speed drops to zero ( u = 0 u = 0 u = 0 )
- Derivation of Flow-Density Parabola
Substituting Greenshields speed into the fundamental flow equation q = u ⋅ k q = u \cdot k q = u ⋅ k :
q = k [ u f ( 1 − k k j ) ] = u f k − u f k j k 2 q = k \left[ u_f \left( 1 - \frac{k}{k_j} \right) \right] = u_f k - \frac{u_f}{k_j} k^2 q = k [ u f ( 1 − k j k ) ] = u f k − k j u f k 2
This is the equation of a downward-opening parabola passing through the origin ( 0 , 0 ) (0,0) ( 0 , 0 ) and jam density ( k j , 0 ) (k_j, 0) ( k j , 0 ) . To find the density that maximizes flow, differentiate q q q with respect to k k k and set the derivative to zero:
d q d k = u f − 2 u f k j k = 0 ⟹ k c = k j 2 \frac{dq}{dk} = u_f - \frac{2 u_f}{k_j} k = 0 \implies k_c = \frac{k_j}{2} d k d q = u f − k j 2 u f k = 0 ⟹ k c = 2 k j
Where k c k_c k c is the critical density . Substituting k c k_c k c into the speed-density equation yields the critical speed ( u c u_c u c ) :
u c = u f ( 1 − k j / 2 k j ) = u f 2 u_c = u_f \left( 1 - \frac{k_j / 2}{k_j} \right) = \frac{u_f}{2} u c = u f ( 1 − k j k j /2 ) = 2 u f
Maximum Roadway Capacity ( q max q_{\max} q m a x )
The maximum flow rate (roadway capacity) is the product of critical speed and critical density:
q max = u c ⋅ k c = ( u f 2 ) ( k j 2 ) = u f k j 4 q_{\max} = u_c \cdot k_c = \left( \frac{u_f}{2} \right) \left( \frac{k_j}{2} \right) = \frac{u_f k_j}{4} q m a x = u c ⋅ k c = ( 2 u f ) ( 2 k j ) = 4 u f k j
Speed-Flow Relationship
Expressing density in terms of speed k = k j ( 1 − u / u f ) k = k_j (1 - u / u_f) k = k j ( 1 − u / u f ) and substituting into q = u ⋅ k q = u \cdot k q = u ⋅ k yields the speed-flow parabolic equation:
q = k j ( u − u 2 u f ) q = k_j \left( u - \frac{u^2}{u_f} \right) q = k j ( u − u f u 2 )
For any flow rate below capacity ( q < q max q < q_{\max} q < q m a x ), there exist two operational regimes :
Uncongested / Free-Flow Regime: High speed ( u > u c u > u_c u > u c ) and low density ( k < k c k < k_c k < k c ). Traffic is stable, and drivers maintain desired travel speeds.
Congested / Forced-Flow Regime: Low speed ( u < u c u < u_c u < u c ) and high density ( k > k c k > k_c k > k c ). Flow is constrained by downstream bottlenecks, producing stop-and-go waves.
Highway Capacity & Level of Service (LOS)
The Highway Capacity Manual (HCM) defines Level of Service (LOS) as a qualitative measure describing operational driving conditions within a traffic stream, graded from LOS A (best) to LOS F (worst):
Each facility type has its own LOS measure. For basic freeway segments, the HCM uses density in passenger cars per mile per lane (pc/mi/ln). The thresholds below follow the 6th edition:
- Level of Service Operational Description Basic freeway density (pc/mi/ln)
- LOS A Free flow; drivers essentially unaffected by others ≤ 11 \le 11 ≤ 11
- LOS B Reasonably free flow; slight restriction on maneuvering > 11 > 11 > 11 to 18 18 18
- LOS C Stable flow; lane changes need care > 18 > 18 > 18 to 26 26 26
- LOS D Approaching unstable flow; small incidents cause queues > 26 > 26 > 26 to 35 35 35
- LOS E Operation at or near capacity; no freedom to maneuver > 35 > 35 > 35 to 45 45 45
- LOS F Breakdown flow; demand exceeds capacity > 45 > 45 > 45 , or demand-to-capacity ratio above 1
- Pavement Engineering: Flexible vs Rigid Pavements
Highway pavements are broadly classified into two categories based on how they distribute structural loads into the subgrade:
- Design Feature Flexible Pavements (Asphalt) Rigid Pavements (Portland Cement Concrete)
- Primary Surface Material Asphaltic concrete (bitumen + aggregates) Portland cement concrete (PCC) slabs
Structural Action Grain-to-grain contact; compressive stress dissipation with depth Slab beam/plate bending action over broad subgrade area
Flexural Modulus Low flexural stiffness ( E ≈ 1.5 to 3.5 GPa E \approx 1.5\text{ to }3.5\text{ GPa} E ≈ 1.5 to 3.5 GPa ) Very high flexural stiffness ( E ≈ 25 to 35 GPa E \approx 25\text{ to }35\text{ GPa} E ≈ 25 to 35 GPa )
Subgrade Strength Influence Subgrade bearing capacity directly governs layer thicknesses Subgrade strength has minor influence due to slab bridging action
Joint Requirements Continuous surface; no expansion/contraction joints required Transverse contraction joints with smooth dowel bars mandated
- Flexible Pavement Design: AASHTO Structural Number (SN)
- Equivalent Single Axle Load (ESAL)
To evaluate mixed traffic composed of passenger cars, buses, and multi-axle heavy haul trucks, traffic loads are converted into an equivalent standard reference axle. The standard reference is the 18-kip (18,000 lbs / 80 kN / 8.2 metric tonnes) Equivalent Single Axle Load (ESAL) .
Under the AASHO Road Test fourth-power damage law , the Load Equivalency Factor (LEF) for an axle load L x L_x L x is approximately:
LEF ≈ ( L x 18 kips ) 4 = ( L x 80 kN ) 4 \text{LEF} \approx \left( \frac{L_x}{18\text{ kips}} \right)^4 = \left( \frac{L_x}{80\text{ kN}} \right)^4 LEF ≈ ( 18 kips L x ) 4 = ( 80 kN L x ) 4
Note
A single 36-kip (160 kN) axle inflicts ( 36 / 18 ) 4 = 2 4 = 16 times (36/18)^4 = 2^4 = 16\text{ times} ( 36/18 ) 4 = 2 4 = 16 times more structural fatigue damage on a pavement than a single standard 18-kip axle.
AASHTO Structural Number Equation
The Structural Number (SN) is an empirical index representing the overall structural capacity required of a flexible pavement to support cumulative design ESALs:
SN = a 1 D 1 + a 2 D 2 m 2 + a 3 D 3 m 3 \text{SN} = a_1 D_1 + a_2 D_2 m_2 + a_3 D_3 m_3 SN = a 1 D 1 + a 2 D 2 m 2 + a 3 D 3 m 3
Where:
a 1 , a 2 , a 3 a_1, a_2, a_3 a 1 , a 2 , a 3 = structural layer coefficients for the surface course, base course, and subbase course
Typical values: a 1 ≈ 0.40 to 0.44 a_1 \approx 0.40\text{ to }0.44 a 1 ≈ 0.40 to 0.44 (dense-graded asphalt concrete), a 2 ≈ 0.12 to 0.14 a_2 \approx 0.12\text{ to }0.14 a 2 ≈ 0.12 to 0.14 (crushed stone base), a 3 ≈ 0.10 to 0.12 a_3 \approx 0.10\text{ to }0.12 a 3 ≈ 0.10 to 0.12 (granular subbase)
D 1 , D 2 , D 3 D_1, D_2, D_3 D 1 , D 2 , D 3 = thickness of respective layers in inches
m 2 , m 3 m_2, m_3 m 2 , m 3 = drainage modification coefficients (dimensionless, typically 0.80 to 1.15 0.80\text{ to }1.15 0.80 to 1.15 based on rainfall and drainage quality)
Rigid Pavement Joints & Load Transfer Detailing
Portland cement concrete slabs expand and contract with temperature and moisture cycles. Without engineered joints, unrestrained shrinkage induces irregular, destructive thermal curling and cracking.
1. Transverse Contraction Joints
Function: Relieve tensile stresses induced by drying shrinkage and thermal contraction.
Spacing: Commonly about 4.5 to 5.0 m 4.5\text{ to }5.0\text{ m} 4.5 to 5.0 m for plain jointed slabs. A frequently used rule of thumb limits spacing to roughly 21 to 24 times the slab thickness.
Joint Sawing: Cut to a depth of D / 4 D/4 D /4 to D / 3 D/3 D /3 (where D D D is slab thickness) within 6 to 12 hours of concrete placement.
2. Dowel Bars
Mechanics: Smooth, round solid steel bars installed across transverse joints at slab mid-depth.
Load Transfer: Provide vertical shear transfer across adjacent slabs, preventing joint faulting and pumping, while their lubricated surface permits free longitudinal expansion and contraction.
Sizing: Typically 28 to 36 mm 28\text{ to }36\text{ mm} 28 to 36 mm diameter, 450 mm 450\text{ mm} 450 mm length, spaced at 300 mm 300\text{ mm} 300 mm on center.
3. Longitudinal Joints & Tie Bars
Mechanics: Deformed (corrugated) steel rebars installed across longitudinal construction joints between adjacent lanes.
Function: Tie bars prevent lane separation and lateral slab migration while allowing joint hinge rotation. Unlike dowels, tie bars are bonded and do not permit sliding.
- Step-by-Step Worked Problem Examples
- Worked Example 1: Greenshields Model Parameter Analysis
Problem: A multi-lane expressway has an estimated free-flow speed u f = 96 km/h u_f = 96\text{ km/h} u f = 96 km/h and a jam density k j = 110 veh/km/lane k_j = 110\text{ veh/km/lane} k j = 110 veh/km/lane . Assuming Greenshields linear stream behavior:
Determine the maximum lane capacity ( q max q_{\max} q m a x ), critical speed ( u c u_c u c ), and critical density ( k c k_c k c ).
Calculate the speed and density when the flow rate is operating at 2 , 100 veh/h/lane 2,100\text{ veh/h/lane} 2 , 100 veh/h/lane in the uncongested regime.
Calculate the flow rate when density is observed at k = 75 veh/km/lane k = 75\text{ veh/km/lane} k = 75 veh/km/lane .
Solution:
Capacity and Critical Parameters: u c = u f 2 = 96 2 = 48.0 km/h u_c = \frac{u_f}{2} = \frac{96}{2} = 48.0\text{ km/h} u c = 2 u f = 2 96 = 48.0 km/h k c = k j 2 = 110 2 = 55.0 veh/km/lane k_c = \frac{k_j}{2} = \frac{110}{2} = 55.0\text{ veh/km/lane} k c = 2 k j = 2 110 = 55.0 veh/km/lane q max = u c ⋅ k c = 48.0 × 55.0 = 2 , 640 veh/h/lane q_{\max} = u_c \cdot k_c = 48.0 \times 55.0 = 2,640\text{ veh/h/lane} q m a x = u c ⋅ k c = 48.0 × 55.0 = 2 , 640 veh/h/lane
Operating Parameters at q = 2 , 100 veh/h q = 2,100\text{ veh/h} q = 2 , 100 veh/h : Using the parabolic speed-flow relationship: q = k j ( u − u 2 u f ) ⟹ 2100 = 110 ( u − u 2 96 ) q = k_j \left( u - \frac{u^2}{u_f} \right) \implies 2100 = 110 \left( u - \frac{u^2}{96} \right) q = k j ( u − u f u 2 ) ⟹ 2100 = 110 ( u − 96 u 2 ) 19.0909 = u − u 2 96 ⟹ u 2 96 − u + 19.0909 = 0 19.0909 = u - \frac{u^2}{96} \implies \frac{u^2}{96} - u + 19.0909 = 0 19.0909 = u − 96 u 2 ⟹ 96 u 2 − u + 19.0909 = 0 u 2 − 96 u + 1832.73 = 0 u^2 - 96 u + 1832.73 = 0 u 2 − 96 u + 1832.73 = 0 Solving via quadratic formula: u = 96 ± ( − 96 ) 2 − 4 ( 1 ) ( 1832.73 ) 2 = 96 ± 9216 − 7330.91 2 = 96 ± 1885.09 2 = 96 ± 43.42 2 u = \frac{96 \pm \sqrt{(-96)^2 - 4(1)(1832.73)}}{2} = \frac{96 \pm \sqrt{9216 - 7330.91}}{2} = \frac{96 \pm \sqrt{1885.09}}{2} = \frac{96 \pm 43.42}{2} u = 2 96 ± ( − 96 ) 2 − 4 ( 1 ) ( 1832.73 ) = 2 96 ± 9216 − 7330.91 = 2 96 ± 1885.09 = 2 96 ± 43.42
In the uncongested regime ( u > u c = 48 km/h u > u_c = 48\text{ km/h} u > u c = 48 km/h ): u = 96 + 43.42 2 = 69.71 km/h u = \frac{96 + 43.42}{2} = 69.71\text{ km/h} u = 2 96 + 43.42 = 69.71 km/h
Corresponding density: k = q u = 2100 69.71 = 30.12 veh/km/lane k = \frac{q}{u} = \frac{2100}{69.71} = 30.12\text{ veh/km/lane} k = u q = 69.71 2100 = 30.12 veh/km/lane
Flow at Density k = 75 veh/km k = 75\text{ veh/km} k = 75 veh/km : Speed at k = 75 veh/km k = 75\text{ veh/km} k = 75 veh/km : u = u f ( 1 − k k j ) = 96 ( 1 − 75 110 ) = 96 ( 35 110 ) = 30.55 km/h u = u_f \left( 1 - \frac{k}{k_j} \right) = 96 \left( 1 - \frac{75}{110} \right) = 96 \left( \frac{35}{110} \right) = 30.55\text{ km/h} u = u f ( 1 − k j k ) = 96 ( 1 − 110 75 ) = 96 ( 110 35 ) = 30.55 km/h q = u ⋅ k = 30.55 × 75 = 2 , 291 veh/h/lane q = u \cdot k = 30.55 \times 75 = 2,291\text{ veh/h/lane} q = u ⋅ k = 30.55 × 75 = 2 , 291 veh/h/lane (Note: Since k = 75 > k c = 55 k = 75 > k_c = 55 k = 75 > k c = 55 , this represents congested forced flow).
Worked Example 2: Flexible Pavement Layer Thickness Design
Problem: A national highway requires an AASHTO Structural Number SN = 4.30 \text{SN} = 4.30 SN = 4.30 to accommodate cumulative 20-year design traffic loads. The pavement structure consists of:
Surface Course: Dense-graded asphalt concrete, a 1 = 0.42 a_1 = 0.42 a 1 = 0.42 , thickness D 1 = 4.0 inches D_1 = 4.0\text{ inches} D 1 = 4.0 inches .
Base Course: Crushed aggregate base, a 2 = 0.14 a_2 = 0.14 a 2 = 0.14 , drainage coefficient m 2 = 1.0 m_2 = 1.0 m 2 = 1.0 , thickness D 2 = 8.0 inches D_2 = 8.0\text{ inches} D 2 = 8.0 inches .
Subbase Course: Granular subbase, a 3 = 0.11 a_3 = 0.11 a 3 = 0.11 , drainage coefficient m 3 = 0.85 m_3 = 0.85 m 3 = 0.85 .
Calculate the required thickness of the granular subbase layer ( D 3 D_3 D 3 ) rounded to the nearest half-inch.
Solution:
AASHTO Structural Number Equation: SN = a 1 D 1 + a 2 D 2 m 2 + a 3 D 3 m 3 \text{SN} = a_1 D_1 + a_2 D_2 m_2 + a_3 D_3 m_3 SN = a 1 D 1 + a 2 D 2 m 2 + a 3 D 3 m 3
Evaluate Contributions of Surface and Base Layers: SN 1 = a 1 D 1 = 0.42 × 4.0 = 1.68 \text{SN}_1 = a_1 D_1 = 0.42 \times 4.0 = 1.68 SN 1 = a 1 D 1 = 0.42 × 4.0 = 1.68 SN 2 = a 2 D 2 m 2 = 0.14 × 8.0 × 1.0 = 1.12 \text{SN}_2 = a_2 D_2 m_2 = 0.14 \times 8.0 \times 1.0 = 1.12 SN 2 = a 2 D 2 m 2 = 0.14 × 8.0 × 1.0 = 1.12 SN 1 + 2 = 1.68 + 1.12 = 2.80 \text{SN}_{1+2} = 1.68 + 1.12 = 2.80 SN 1 + 2 = 1.68 + 1.12 = 2.80
Compute Required Subbase Contribution: Δ SN 3 = SN total − SN 1 + 2 = 4.30 − 2.80 = 1.50 \Delta \text{SN}_3 = \text{SN}_{\text{total}} - \text{SN}_{1+2} = 4.30 - 2.80 = 1.50 Δ SN 3 = SN total − SN 1 + 2 = 4.30 − 2.80 = 1.50
Solve for Subbase Thickness D 3 D_3 D 3 : a 3 D 3 m 3 = 1.50 ⟹ D 3 = 1.50 a 3 m 3 = 1.50 0.11 × 0.85 = 1.50 0.0935 = 16.04 inches a_3 D_3 m_3 = 1.50 \implies D_3 = \frac{1.50}{a_3 m_3} = \frac{1.50}{0.11 \times 0.85} = \frac{1.50}{0.0935} = 16.04\text{ inches} a 3 D 3 m 3 = 1.50 ⟹ D 3 = a 3 m 3 1.50 = 0.11 × 0.85 1.50 = 0.0935 1.50 = 16.04 inches Rounding to the nearest standard construction half-inch yields D 3 = 16.0 inches D_3 = 16.0\text{ inches} D 3 = 16.0 inches (or 400 mm 400\text{ mm} 400 mm ).
CELE Board Exam Traps & Strategic Checklists
Warning
Speed Average Trap: Radar measurements at a point yield time-mean speed ( u t u_t u t ) . You can never calculate flow via q = u t ⋅ k q = u_t \cdot k q = u t ⋅ k . You must convert to space-mean speed ( u s u_s u s ) using Wardrop's formula u t = u s + σ s 2 / u s u_t = u_s + \sigma_s^2 / u_s u t = u s + σ s 2 / u s or by taking the harmonic mean of individual speeds.
Capacity Divisor: The maximum capacity in Greenshields model is q max = u f k j 4 q_{\max} = \frac{u_f k_j}{4} q m a x = 4 u f k j , not u f k j 2 \frac{u_f k_j}{2} 2 u f k j . Forgetting the second divisor of 2 from speed is a chronic mistake.
Dowel Bars vs Tie Bars: Remember their physical distinctions:
Dowel bars: Smooth, round, greased, located at transverse contraction joints, transfer vertical shear without restraining axial slab expansion/contraction.
Tie bars: Deformed rebar, ungreased/bonded, located at longitudinal joints, resist lateral lane separation.