Study guide
14.2 Doubly Reinforced Beams and T-Beams
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
14.2 Doubly Reinforced Beams and T-Beams
Key Takeaways Explain This Topic AI
Compression reinforcement ( A s ′ A'_s A s ′ ) is primarily specified to control long-term creep and shrinkage deflections (governed by multiplier λ Δ = ξ 1 + 50 ρ ′ \lambda_\Delta = \frac{\xi}{1 + 50\rho'} λ Δ = 1 + 50 ρ ′ ξ ), improve section ductility, and resist seismic moment reversals in depth-restricted beams.
The stress in compression steel depends directly on its strain ϵ s ′ = 0.003 ( c − d ′ c ) \epsilon'_s = 0.003 \left(\frac{c - d'}{c}\right) ϵ s ′ = 0.003 ( c c − d ′ ) ; compression steel yields ( f s ′ = f y f'_s = f_y f s ′ = f y ) only if neutral axis depth satisfies c ≥ 600 d ′ 600 − f y c \ge \frac{600 d'}{600 - f_y} c ≥ 600 − f y 600 d ′ or when ( ρ − ρ ′ ) ≥ 0.85 f c ′ β 1 d ′ f y d ( 600 600 − f y ) (\rho - \rho') \ge \frac{0.85 f'_c \beta_1 d'}{f_y d}\left(\frac{600}{600 - f_y}\right) ( ρ − ρ ′ ) ≥ f y d 0.85 f c ′ β 1 d ′ ( 600 − f y 600 ) .
When compression steel does not yield ( f s ′ < f y f'_s < f_y f s ′ < f y ), the neutral axis depth c c c must be determined by solving the quadratic force equilibrium equation: 0.85 f c ′ β 1 b c 2 + ( 600 A s ′ − A s f y ) c − 600 A s ′ d ′ = 0 0.85 f'_c \beta_1 b c^2 + (600 A'_s - A_s f_y) c - 600 A'_s d' = 0 0.85 f c ′ β 1 b c 2 + ( 600 A s ′ − A s f y ) c − 600 A s ′ d ′ = 0 .
Under NSCP 2015 Section 406.3.2 (ACI 318-14 Table 6.3.2.1), each overhang of an interior T-beam is limited to the least of 8 h f 8h_f 8 h f , half the clear distance to the next web, and ℓ n / 8 \ell_n/8 ℓ n /8 , so b e ≤ b w + 16 h f b_e \le b_w + 16h_f b e ≤ b w + 16 h f , b e ≤ b_e \le b e ≤ center-to-center spacing, and b e ≤ b w + ℓ n / 4 b_e \le b_w + \ell_n/4 b e ≤ b w + ℓ n /4 .
A T-beam behaves as a rectangular beam of width b e b_e b e when the equivalent stress block depth a ≤ h f a \le h_f a ≤ h f ; it acts as a true T-beam when a > h f a > h_f a > h f , requiring separate decomposition into overhanging flange and web compressive components.
Last updated: October 2026
14.2 Doubly Reinforced Beams and T-Beams
When structural beam dimensions are constrained by architectural headroom or clearance limits, tension reinforcement alone may exceed the maximum permissible steel ratio ( ρ max \rho_{\max} ρ m a x ), resulting in a non-ductile compression failure. To overcome this limitation, structural engineers add compression reinforcement ( A s ′ A'_s A s ′ ) , creating a doubly reinforced beam . Furthermore, in cast-in-place reinforced concrete floor systems, floor slabs are poured monolithically with the supporting beams, forming flanged sections known as T-beams (interior bays) and L-beams (spandrel/edge beams). Understanding the flexural mechanics of both systems is a staple of the PRC Civil Engineering Licensure Examination.
1. Role and Behavior of Compression Steel ( A s ′ A'_s A s ′ )
Although compression steel increases the ultimate flexural capacity of a beam, that is rarely its primary design objective. The key engineering reasons for providing compression steel include:
Long-Term Deflection Control: Concrete undergoes creep and drying shrinkage under sustained dead and live loads. Compression reinforcement carries a progressively increasing portion of the compressive force, relieving the concrete and dramatically suppressing long-term deflections. Under NSCP 2015 Section 424.2.4.1.1, the long-term deflection multiplier is: λ Δ = ξ 1 + 50 ρ ′ \lambda_\Delta = \frac{\xi}{1 + 50 \rho'} λ Δ = 1 + 50 ρ ′ ξ where ρ ′ = A s ′ / ( b d ) \rho' = A'_s / (b d) ρ ′ = A s ′ / ( b d ) and ξ \xi ξ is a time-dependent factor ( 2.0 2.0 2.0 for ≥ 5 \ge 5 ≥ 5 years, 1.4 1.4 1.4 for 12 months, 1.2 1.2 1.2 for 6 months, 1.0 1.0 1.0 for 3 months).
Ductility Enhancement: By carrying compressive forces, compression steel allows the concrete compression block depth ( c c c ) to decrease. This shifts the neutral axis upward, significantly increasing the net tensile strain ( ϵ t \epsilon_t ϵ t ) in the tension steel and guaranteeing tension-controlled ductile failure ( ϕ = 0.90 \phi = 0.90 ϕ = 0.90 ).
Seismic Moment Reversal: During severe earthquake shaking, lateral sway induces positive moments at beam ends that normally experience negative moments, requiring bottom reinforcement to act in tension and top reinforcement in compression.
Fabrication Rigidity: Compression bars provide secure top anchoring points for shear stirrups and prevent distortion of the reinforcement cage during concrete casting.
2. Strain Compatibility and Yield Verification for Compression Steel
Unlike tension reinforcement—which is designed to yield—compression reinforcement may or may not yield before the concrete reaches its crushing strain of ϵ u = 0.003 \epsilon_u = 0.003 ϵ u = 0.003 .
From the linear strain diagram across the section:
ϵ s ′ c − d ′ = 0.003 c ⟹ ϵ s ′ = 0.003 ( c − d ′ c ) \frac{\epsilon'_s}{c - d'} = \frac{0.003}{c} \implies \epsilon'_s = 0.003 \left(\frac{c - d'}{c}\right) c − d ′ ϵ s ′ = c 0.003 ⟹ ϵ s ′ = 0.003 ( c c − d ′ )
Where d ′ d' d ′ is the distance from the extreme compression fiber to the centroid of the compression steel.
Condition for Compression Steel Yielding
The compression reinforcement yields if its strain exceeds the yield strain: ϵ s ′ ≥ ϵ y = f y / E s \epsilon'_s \ge \epsilon_y = f_y / E_s ϵ s ′ ≥ ϵ y = f y / E s .
Setting ϵ s ′ = f y 200 , 000 \epsilon'_s = \frac{f_y}{200,000} ϵ s ′ = 200 , 000 f y :
0.003 ( c − d ′ c ) ≥ f y 200 , 000 ⟹ c ≥ c yield = 600 d ′ 600 − f y 0.003 \left(\frac{c - d'}{c}\right) \ge \frac{f_y}{200,000} \implies c \ge c_{\text{yield}} = \frac{600 d'}{600 - f_y} 0.003 ( c c − d ′ ) ≥ 200 , 000 f y ⟹ c ≥ c yield = 600 − f y 600 d ′
In terms of reinforcement ratios, compression steel yields at nominal strength if and only if:
( ρ − ρ ′ ) ≥ ρ ˉ c y = 0.85 f c ′ β 1 d ′ f y d ( 600 600 − f y ) (\rho - \rho') \ge \bar{\rho}_{cy} = \frac{0.85 f'_c \beta_1 d'}{f_y d} \left(\frac{600}{600 - f_y}\right) ( ρ − ρ ′ ) ≥ ρ ˉ cy = f y d 0.85 f c ′ β 1 d ′ ( 600 − f y 600 )
Where ρ = A s / ( b d ) \rho = A_s / (b d) ρ = A s / ( b d ) and ρ ′ = A s ′ / ( b d ) \rho' = A'_s / (b d) ρ ′ = A s ′ / ( b d ) .
- 3. Equilibrium and Flexural Capacity of Doubly Reinforced Beams
- Case 1: Compression Steel Yields ( f s ′ = f y f'_s = f_y f s ′ = f y )
When c ≥ c yield c \ge c_{\text{yield}} c ≥ c yield :
Concrete compression: C c = 0.85 f c ′ a b C_c = 0.85 f'_c a b C c = 0.85 f c ′ ab
Steel compression: C s = A s ′ ( f y − 0.85 f c ′ ) C_s = A'_s (f_y - 0.85 f'_c) C s = A s ′ ( f y − 0.85 f c ′ ) (or approximately C s = A s ′ f y C_s = A'_s f_y C s = A s ′ f y if concrete displaced by steel is neglected)
Steel tension: T = A s f y T = A_s f_y T = A s f y
Enforcing horizontal equilibrium ( ∑ F x = 0 \sum F_x = 0 ∑ F x = 0 ):
C c + C s = T ⟹ 0.85 f c ′ a b + A s ′ f y = A s f y C_c + C_s = T \implies 0.85 f'_c a b + A'_s f_y = A_s f_y C c + C s = T ⟹ 0.85 f c ′ ab + A s ′ f y = A s f y
a = ( A s − A s ′ ) f y 0.85 f c ′ b a = \frac{(A_s - A'_s) f_y}{0.85 f'_c b} a = 0.85 f c ′ b ( A s − A s ′ ) f y
The nominal moment capacity ( M n M_n M n ) is the sum of the concrete couple ( M n 1 M_{n1} M n 1 ) and the compression steel couple ( M n 2 M_{n2} M n 2 ):
M n = M n 1 + M n 2 = 0.85 f c ′ a b ( d − a 2 ) + A s ′ f y ( d − d ′ ) M_n = M_{n1} + M_{n2} = 0.85 f'_c a b \left(d - \frac{a}{2}\right) + A'_s f_y (d - d') M n = M n 1 + M n 2 = 0.85 f c ′ ab ( d − 2 a ) + A s ′ f y ( d − d ′ )
Case 2: Compression Steel Does Not Yield ( f s ′ < f y f'_s < f_y f s ′ < f y )
When c < c yield c < c_{\text{yield}} c < c yield , the stress in the compression steel is governed by Hooke's Law:
f s ′ = E s ϵ s ′ = 200 , 000 × 0.003 ( c − d ′ c ) = 600 ( c − d ′ c ) f'_s = E_s \epsilon'_s = 200,000 \times 0.003 \left(\frac{c - d'}{c}\right) = 600 \left(\frac{c - d'}{c}\right) f s ′ = E s ϵ s ′ = 200 , 000 × 0.003 ( c c − d ′ ) = 600 ( c c − d ′ )
Substituting into horizontal equilibrium ( 0.85 f c ′ a b + A s ′ f s ′ = A s f y 0.85 f'_c a b + A'_s f'_s = A_s f_y 0.85 f c ′ ab + A s ′ f s ′ = A s f y ) with a = β 1 c a = \beta_1 c a = β 1 c :
0.85 f c ′ ( β 1 c ) b + A s ′ [ 600 ( c − d ′ c ) ] = A s f y 0.85 f'_c (\beta_1 c) b + A'_s \left[600 \left(\frac{c - d'}{c}\right)\right] = A_s f_y 0.85 f c ′ ( β 1 c ) b + A s ′ [ 600 ( c c − d ′ ) ] = A s f y
Multiplying through by c c c produces a quadratic equation in c c c :
( 0.85 f c ′ β 1 b ) c 2 + ( 600 A s ′ − A s f y ) c − 600 A s ′ d ′ = 0 (0.85 f'_c \beta_1 b) c^2 + (600 A'_s - A_s f_y) c - 600 A'_s d' = 0 ( 0.85 f c ′ β 1 b ) c 2 + ( 600 A s ′ − A s f y ) c − 600 A s ′ d ′ = 0
Solving this quadratic equation yields the exact neutral axis depth c c c . The depth of the stress block is a = β 1 c a = \beta_1 c a = β 1 c , and the compression steel stress is f s ′ = 600 ( c − d ′ ) / c f'_s = 600 (c - d') / c f s ′ = 600 ( c − d ′ ) / c . Nominal moment capacity is:
M n = 0.85 f c ′ a b ( d − a 2 ) + A s ′ f s ′ ( d − d ′ ) M_n = 0.85 f'_c a b \left(d - \frac{a}{2}\right) + A'_s f'_s (d - d') M n = 0.85 f c ′ ab ( d − 2 a ) + A s ′ f s ′ ( d − d ′ )
4. T-Beams and Flanged Sections: Geometry and Effective Flange Width
In cast-in-place floor systems, beams and slabs are cast as a single monolithic unit. Under positive bending, the slab acts as a wide compression flange. However, due to shear deformation in the slab (known as shear lag ), longitudinal compressive stresses decrease with distance from the web ( b w b_w b w ). To account for this, codes define an effective flange width ( b e b_e b e ) over which compressive stresses are assumed to be uniform.
NSCP 2015 Criteria for Effective Flange Width (Section 406.3.2)
NSCP 2015 follows ACI 318-14 Table 6.3.2.1, which limits the overhang on each side of the web . Here s w s_w s w is the clear distance to the adjacent web and ℓ n \ell_n ℓ n is the clear span of the beam.
Member Type Overhang limit (least of) Resulting b e b_e b e
Interior T-beam (slab on both sides) 8 h f 8 h_f 8 h f ; s w / 2 s_w / 2 s w /2 ; ℓ n / 8 \ell_n / 8 ℓ n /8 b e = b w + 2 × b_e = b_w + 2 \times b e = b w + 2 × overhang, so b e ≤ b w + 16 h f b_e \le b_w + 16 h_f b e ≤ b w + 16 h f , b e ≤ b w + s w b_e \le b_w + s_w b e ≤ b w + s w (center-to-center spacing), b e ≤ b w + ℓ n / 4 b_e \le b_w + \ell_n/4 b e ≤ b w + ℓ n /4
Edge L-beam (slab on one side) 6 h f 6 h_f 6 h f ; s w / 2 s_w / 2 s w /2 ; ℓ n / 12 \ell_n / 12 ℓ n /12 b e = b w + b_e = b_w + b e = b w + overhang
Isolated T-beam Flange thickness h f ≥ b w / 2 h_f \ge b_w / 2 h f ≥ b w /2 Total flange width b e ≤ 4 b w b_e \le 4 b_w b e ≤ 4 b w
Note
Older codes (ACI 318-11 and NSCP 2010) limited an interior T-beam to one-fourth of the beam span overall. NSCP 2015 uses one-eighth of the clear span per side , which gives one-fourth of the clear span in total.
5. Flexural Analysis of T-Beams
Analysis of a flanged section begins by determining whether the compression zone penetrates into the web. <-------------- b_e -------------->
- =================================== ^
- | Flange | | h_f
- =================================== v
- | Web |
- | (b_w) |
Compute the maximum compressive capacity that the entire flange can provide:
C f , max = 0.85 f c ′ b e h f C_{f,\max} = 0.85 f'_c b_e h_f C f , m a x = 0.85 f c ′ b e h f
Calculate the total tensile force at yield: T = A s f y T = A_s f_y T = A s f y .
Condition A: Rectangular Beam Behavior ( T ≤ C f , max ⟹ a ≤ h f T \le C_{f,\max} \implies a \le h_f T ≤ C f , m a x ⟹ a ≤ h f )
If T ≤ C f , max T \le C_{f,\max} T ≤ C f , m a x , the equivalent rectangular stress block depth a a a is less than or equal to slab thickness h f h_f h f . The neutral axis lies within the flange. The tension concrete in the web is neglected anyway, so the beam behaves identically to a rectangular beam of width b = b e b = b_e b = b e :
a = A s f y 0.85 f c ′ b e ≤ h f a = \frac{A_s f_y}{0.85 f'_c b_e} \le h_f a = 0.85 f c ′ b e A s f y ≤ h f
M n = A s f y ( d − a 2 ) M_n = A_s f_y \left(d - \frac{a}{2}\right) M n = A s f y ( d − 2 a )
Condition B: True T-Beam Behavior ( T > C f , max ⟹ a > h f T > C_{f,\max} \implies a > h_f T > C f , m a x ⟹ a > h f )
If T > C f , max T > C_{f,\max} T > C f , m a x , the compression block penetrates into the web ( a > h f a > h_f a > h f ). The compression zone consists of two distinct parts:
Overhanging Flanges ( b e − b w b_e - b_w b e − b w ): Carries compressive force C f C_f C f : C f = 0.85 f c ′ ( b e − b w ) h f C_f = 0.85 f'_c (b_e - b_w) h_f C f = 0.85 f c ′ ( b e − b w ) h f Balanced by tension steel area A s f = C f f y A_{sf} = \frac{C_f}{f_y} A s f = f y C f .
Moment arm: ( d − h f / 2 ) (d - h_f / 2) ( d − h f /2 ) .
Web Compression ( b w × a b_w \times a b w × a ): Carries compressive force C w C_w C w : C w = 0.85 f c ′ a b w C_w = 0.85 f'_c a b_w C w = 0.85 f c ′ a b w Balanced by remaining tension steel: A s w = A s − A s f A_{sw} = A_s - A_{sf} A s w = A s − A s f .
Depth of web compression block: a = A s w f y 0.85 f c ′ b w = ( A s − A s f ) f y 0.85 f c ′ b w a = \frac{A_{sw} f_y}{0.85 f'_c b_w} = \frac{(A_s - A_{sf}) f_y}{0.85 f'_c b_w} a = 0.85 f c ′ b w A s w f y = 0.85 f c ′ b w ( A s − A s f ) f y Moment arm: ( d − a / 2 ) (d - a / 2) ( d − a /2 ) .
Total nominal flexural strength is:
M n = M n f + M n w = C f ( d − h f 2 ) + C w ( d − a 2 ) M_n = M_{nf} + M_{nw} = C_f \left(d - \frac{h_f}{2}\right) + C_w \left(d - \frac{a}{2}\right) M n = M n f + M n w = C f ( d − 2 h f ) + C w ( d − 2 a )
M n = 0.85 f c ′ ( b e − b w ) h f ( d − h f 2 ) + 0.85 f c ′ a b w ( d − a 2 ) M_n = 0.85 f'_c (b_e - b_w) h_f \left(d - \frac{h_f}{2}\right) + 0.85 f'_c a b_w \left(d - \frac{a}{2}\right) M n = 0.85 f c ′ ( b e − b w ) h f ( d − 2 h f ) + 0.85 f c ′ a b w ( d − 2 a )
- 6. Comprehensive Worked Examples
- Worked Example 1: Analysis of a Doubly Reinforced Beam
Problem: A rectangular beam has b = 350 mm b = 350\text{ mm} b = 350 mm , effective depth d = 600 mm d = 600\text{ mm} d = 600 mm , and compression steel depth d ′ = 65 mm d' = 65\text{ mm} d ′ = 65 mm . The beam is reinforced with 6 − ϕ 32 mm 6 - \phi 32\text{ mm} 6 − ϕ 32 mm tension bars ( A s = 4825.5 mm 2 A_s = 4825.5\text{ mm}^2 A s = 4825.5 mm 2 ) and 2 − ϕ 25 mm 2 - \phi 25\text{ mm} 2 − ϕ 25 mm compression bars ( A s ′ = 981.7 mm 2 A'_s = 981.7\text{ mm}^2 A s ′ = 981.7 mm 2 ). Material strengths are f c ′ = 28 MPa f'_c = 28\text{ MPa} f c ′ = 28 MPa and f y = 420 MPa f_y = 420\text{ MPa} f y = 420 MPa . Determine whether the compression steel yields and calculate the nominal moment capacity M n M_n M n .
Solution:
Step 1: Check Yield Condition of Compression Steel: For f c ′ = 28 MPa f'_c = 28\text{ MPa} f c ′ = 28 MPa , β 1 = 0.85 \beta_1 = 0.85 β 1 = 0.85 .
The yield limit for neutral axis depth is: c yield = 600 d ′ 600 − f y = 600 × 65 600 − 420 = 39 , 000 180 = 216.67 mm c_{\text{yield}} = \frac{600 d'}{600 - f_y} = \frac{600 \times 65}{600 - 420} = \frac{39,000}{180} = 216.67\text{ mm} c yield = 600 − f y 600 d ′ = 600 − 420 600 × 65 = 180 39 , 000 = 216.67 mm
Assume compression steel yields ( f s ′ = f y = 420 MPa f'_s = f_y = 420\text{ MPa} f s ′ = f y = 420 MPa ): a = ( A s − A s ′ ) f y 0.85 f c ′ b = ( 4825.5 − 981.7 ) × 420 0.85 × 28 × 350 = 3843.8 × 420 8330 = 193.80 mm a = \frac{(A_s - A'_s) f_y}{0.85 f'_c b} = \frac{(4825.5 - 981.7) \times 420}{0.85 \times 28 \times 350} = \frac{3843.8 \times 420}{8330} = 193.80\text{ mm} a = 0.85 f c ′ b ( A s − A s ′ ) f y = 0.85 × 28 × 350 ( 4825.5 − 981.7 ) × 420 = 8330 3843.8 × 420 = 193.80 mm c = a β 1 = 193.80 0.85 = 228.00 mm c = \frac{a}{\beta_1} = \frac{193.80}{0.85} = 228.00\text{ mm} c = β 1 a = 0.85 193.80 = 228.00 mm
Check assumption: Since c = 228.00 mm > c yield = 216.67 mm c = 228.00\text{ mm} > c_{\text{yield}} = 216.67\text{ mm} c = 228.00 mm > c yield = 216.67 mm , the compression steel has yielded ( f s ′ = f y = 420 MPa f'_s = f_y = 420\text{ MPa} f s ′ = f y = 420 MPa ). Assumption verified!
Step 2: Check Tension Steel Ductility: ϵ t = 0.003 ( d − c c ) = 0.003 ( 600 − 228.0 228.0 ) = 0.00489 \epsilon_t = 0.003 \left(\frac{d - c}{c}\right) = 0.003 \left(\frac{600 - 228.0}{228.0}\right) = 0.00489 ϵ t = 0.003 ( c d − c ) = 0.003 ( 228.0 600 − 228.0 ) = 0.00489 Since 0.002 < ϵ t = 0.00489 < 0.005 0.002 < \epsilon_t = 0.00489 < 0.005 0.002 < ϵ t = 0.00489 < 0.005 , the beam is in the transition zone: ϕ = 0.65 + ( 0.00489 − 0.002 ) × ( 250 3 ) = 0.65 + 0.2408 = 0.891 \phi = 0.65 + (0.00489 - 0.002) \times \left(\frac{250}{3}\right) = 0.65 + 0.2408 = 0.891 ϕ = 0.65 + ( 0.00489 − 0.002 ) × ( 3 250 ) = 0.65 + 0.2408 = 0.891
Step 3: Calculate Nominal Moment Strength ( M n M_n M n ): C c = 0.85 f c ′ a b = 0.85 × 28 × 193.80 × 350 × 10 − 3 = 1614.35 kN C_c = 0.85 f'_c a b = 0.85 \times 28 \times 193.80 \times 350 \times 10^{-3} = 1614.35\text{ kN} C c = 0.85 f c ′ ab = 0.85 × 28 × 193.80 × 350 × 1 0 − 3 = 1614.35 kN C s = A s ′ f y = 981.7 × 420 × 10 − 3 = 412.31 kN C_s = A'_s f_y = 981.7 \times 420 \times 10^{-3} = 412.31\text{ kN} C s = A s ′ f y = 981.7 × 420 × 1 0 − 3 = 412.31 kN M n = C c ( d − a 2 ) + C s ( d − d ′ ) M_n = C_c \left(d - \frac{a}{2}\right) + C_s (d - d') M n = C c ( d − 2 a ) + C s ( d − d ′ ) M n = 1614.35 × ( 600 − 193.80 2 ) × 10 − 3 + 412.31 × ( 600 − 65 ) × 10 − 3 M_n = 1614.35 \times \left(600 - \frac{193.80}{2}\right) \times 10^{-3} + 412.31 \times (600 - 65) \times 10^{-3} M n = 1614.35 × ( 600 − 2 193.80 ) × 1 0 − 3 + 412.31 × ( 600 − 65 ) × 1 0 − 3 M n = 1614.35 × 0.5031 + 412.31 × 0.535 = 812.18 + 220.59 = 1032.77 kN ⋅ m M_n = 1614.35 \times 0.5031 + 412.31 \times 0.535 = 812.18 + 220.59 = 1032.77\text{ kN}\cdot\text{m} M n = 1614.35 × 0.5031 + 412.31 × 0.535 = 812.18 + 220.59 = 1032.77 kN ⋅ m ϕ M n = 0.891 × 1032.77 = 920.20 kN ⋅ m \phi M_n = 0.891 \times 1032.77 = 920.20\text{ kN}\cdot\text{m} ϕ M n = 0.891 × 1032.77 = 920.20 kN ⋅ m
Worked Example 2: Flexural Capacity of a True T-Beam
Problem: An interior T-beam has an effective flange width b e = 900 mm b_e = 900\text{ mm} b e = 900 mm , flange thickness h f = 110 mm h_f = 110\text{ mm} h f = 110 mm , web width b w = 300 mm b_w = 300\text{ mm} b w = 300 mm , and effective depth d = 550 mm d = 550\text{ mm} d = 550 mm . Reinforcement consists of A s = 5200 mm 2 A_s = 5200\text{ mm}^2 A s = 5200 mm 2 . Material strengths are f c ′ = 21 MPa f'_c = 21\text{ MPa} f c ′ = 21 MPa and f y = 420 MPa f_y = 420\text{ MPa} f y = 420 MPa . Determine the nominal moment capacity M n M_n M n .
Solution:
Step 1: Check Flange Capacity vs. Tension Force: T = A s f y = 5200 × 420 = 2 , 184 , 000 N = 2184.0 kN T = A_s f_y = 5200 \times 420 = 2,184,000\text{ N} = 2184.0\text{ kN} T = A s f y = 5200 × 420 = 2 , 184 , 000 N = 2184.0 kN C f , max = 0.85 f c ′ b e h f = 0.85 × 21 × 900 × 110 = 1 , 766 , 970 N = 1767.0 kN C_{f,\max} = 0.85 f'_c b_e h_f = 0.85 \times 21 \times 900 \times 110 = 1,766,970\text{ N} = 1767.0\text{ kN} C f , m a x = 0.85 f c ′ b e h f = 0.85 × 21 × 900 × 110 = 1 , 766 , 970 N = 1767.0 kN Since T = 2184.0 kN > C f , max = 1767.0 kN T = 2184.0\text{ kN} > C_{f,\max} = 1767.0\text{ kN} T = 2184.0 kN > C f , m a x = 1767.0 kN , the stress block penetrates the web ( a > h f a > h_f a > h f ). This is a true T-beam .
Step 2: Flange Component ( M n f M_{nf} M n f ): C f = 0.85 f c ′ ( b e − b w ) h f = 0.85 × 21 × ( 900 − 300 ) × 110 = 1 , 178 , 100 N = 1178.1 kN C_f = 0.85 f'_c (b_e - b_w) h_f = 0.85 \times 21 \times (900 - 300) \times 110 = 1,178,100\text{ N} = 1178.1\text{ kN} C f = 0.85 f c ′ ( b e − b w ) h f = 0.85 × 21 × ( 900 − 300 ) × 110 = 1 , 178 , 100 N = 1178.1 kN A s f = C f f y = 1 , 178 , 100 420 = 2805.0 mm 2 A_{sf} = \frac{C_f}{f_y} = \frac{1,178,100}{420} = 2805.0\text{ mm}^2 A s f = f y C f = 420 1 , 178 , 100 = 2805.0 mm 2 M n f = C f ( d − h f 2 ) = 1178.1 × ( 550 − 110 2 ) × 10 − 3 = 1178.1 × 0.495 = 583.16 kN ⋅ m M_{nf} = C_f \left(d - \frac{h_f}{2}\right) = 1178.1 \times \left(550 - \frac{110}{2}\right) \times 10^{-3} = 1178.1 \times 0.495 = 583.16\text{ kN}\cdot\text{m} M n f = C f ( d − 2 h f ) = 1178.1 × ( 550 − 2 110 ) × 1 0 − 3 = 1178.1 × 0.495 = 583.16 kN ⋅ m
Step 3: Web Component ( M n w M_{nw} M n w ): A s w = A s − A s f = 5200 − 2805.0 = 2395.0 mm 2 A_{sw} = A_s - A_{sf} = 5200 - 2805.0 = 2395.0\text{ mm}^2 A s w = A s − A s f = 5200 − 2805.0 = 2395.0 mm 2 a = A s w f y 0.85 f c ′ b w = 2395.0 × 420 0.85 × 21 × 300 = 1 , 005 , 900 5355 = 187.84 mm a = \frac{A_{sw} f_y}{0.85 f'_c b_w} = \frac{2395.0 \times 420}{0.85 \times 21 \times 300} = \frac{1,005,900}{5355} = 187.84\text{ mm} a = 0.85 f c ′ b w A s w f y = 0.85 × 21 × 300 2395.0 × 420 = 5355 1 , 005 , 900 = 187.84 mm (Note: a = 187.84 mm > h f = 110 mm a = 187.84\text{ mm} > h_f = 110\text{ mm} a = 187.84 mm > h f = 110 mm , confirming web penetration.) M n w = 0.85 f c ′ a b w ( d − a 2 ) = 1005.9 kN × ( 550 − 187.84 2 ) × 10 − 3 M_{nw} = 0.85 f'_c a b_w \left(d - \frac{a}{2}\right) = 1005.9\text{ kN} \times \left(550 - \frac{187.84}{2}\right) \times 10^{-3} M n w = 0.85 f c ′ a b w ( d − 2 a ) = 1005.9 kN × ( 550 − 2 187.84 ) × 1 0 − 3 M n w = 1005.9 × 0.45608 = 458.77 kN ⋅ m M_{nw} = 1005.9 \times 0.45608 = 458.77\text{ kN}\cdot\text{m} M n w = 1005.9 × 0.45608 = 458.77 kN ⋅ m
Step 4: Total Nominal Moment Capacity: M n = M n f + M n w = 583.16 + 458.77 = 1041.93 kN ⋅ m M_n = M_{nf} + M_{nw} = 583.16 + 458.77 = 1041.93\text{ kN}\cdot\text{m} M n = M n f + M n w = 583.16 + 458.77 = 1041.93 kN ⋅ m
7. Licensure Exam Pitfalls & Review Notes
Warning
Pitfall 1: Assuming Compression Steel Always Yields In doubly reinforced beams with low tension steel ratios or deep covers ( d ′ d' d ′ ), the compression steel frequently remains below yield stress ( f s ′ < f y f'_s < f_y f s ′ < f y ). Blindly setting f s ′ = f y f'_s = f_y f s ′ = f y overestimates the concrete block depth a a a and leads to substantial errors on the board exam. Always calculate c yield = 600 d ′ 600 − f y c_{\text{yield}} = \frac{600 d'}{600 - f_y} c yield = 600 − f y 600 d ′ first!
Caution
Pitfall 2: Negative Moment Regions of T-Beams Over intermediate continuous supports, beams experience negative bending moments (tension at the top slab, compression at the bottom). In this region, the slab concrete is in tension and cracks. Therefore, the beam must be analyzed as a rectangular beam of width b w b_w b w , NOT b e b_e b e !
Tip
Pitfall 3: T-Beam Effective Width Rules Remember that the term 16 h f 16 h_f 16 h f applies to symmetrical interior T-beams ( 8 h f 8 h_f 8 h f each side). For an exterior edge L-beam, the overhang is on one side only, so the limit is 6 h f 6 h_f 6 h f , NOT 8 h f 8 h_f 8 h f or 16 h f 16 h_f 16 h f .