Study guide
9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
Key Takeaways Explain This Topic AI
Boussinesq gives the vertical stress under a point load as Δσ = 3Q/(2πz²) directly below the load, decreasing with radial distance.
The 2:1 method spreads a footing load over an area that widens by one unit for every two units of depth: Δσ = P/[(B + z)(L + z)].
Under the center of a uniformly loaded circle of radius R, Δσ = q[1 − 1/(1 + (R/z)²)^1.5].
Stress at an interior point of a rectangle is found by superposing corner-point influence values of sub-rectangles that share that point.
Secondary compression settlement is Cα′H log(t₂/t₁), with Cα′ = Cα/(1 + e_p), and begins after primary consolidation ends.
Last updated: October 2026
9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
The 2022 HGE table of specifications gives Stresses in Soil Mass 12% of the subject (6 items) and Settlement another 12% (6 items). Effective stress from self-weight and seepage is in Section 9.3. Primary consolidation is in Section 10.1. This section supplies the missing pieces:
- the stress increase caused by surface loads, which feeds every settlement calculation;
- immediate settlement;
secondary settlement.
S total = S immediate + S primary + S secondary S_{\text{total}} = S_{\text{immediate}} + S_{\text{primary}} + S_{\text{secondary}} S total = S immediate + S primary + S secondary
Point Loads: Boussinesq and Westergaard
For a vertical point load Q Q Q on the surface of a homogeneous, isotropic, elastic half-space, Boussinesq gives the vertical stress increase at depth z z z and radial distance r r r :
Δ σ z = 3 Q 2 π z 2 ⋅ 1 [ 1 + ( r / z ) 2 ] 5 / 2 \Delta\sigma_z = \frac{3Q}{2\pi z^2}\cdot\frac{1}{\left[1 + (r/z)^2\right]^{5/2}} Δ σ z = 2 π z 2 3 Q ⋅ [ 1 + ( r / z ) 2 ] 5/2 1
Westergaard models soil reinforced by thin, rigid horizontal layers, as in stratified or varved clays. With Poisson's ratio taken as zero:
Δ σ z = Q π z 2 ⋅ 1 [ 1 + 2 ( r / z ) 2 ] 3 / 2 \Delta\sigma_z = \frac{Q}{\pi z^2}\cdot\frac{1}{\left[1 + 2(r/z)^2\right]^{3/2}} Δ σ z = π z 2 Q ⋅ [ 1 + 2 ( r / z ) 2 ] 3/2 1
Example. A column applies Q = 500 kN Q = 500\text{ kN} Q = 500 kN .
Directly below at z = 4 m z = 4\text{ m} z = 4 m , Boussinesq gives 3 ( 500 ) / ( 2 π ⋅ 16 ) = 14.9 kPa 3(500)/(2\pi \cdot 16) = 14.9\text{ kPa} 3 ( 500 ) / ( 2 π ⋅ 16 ) = 14.9 kPa .
At r = 3 m r = 3\text{ m} r = 3 m and the same depth, r / z = 0.75 r/z = 0.75 r / z = 0.75 and [ 1.5625 ] 2.5 = 3.052 [1.5625]^{2.5} = 3.052 [ 1.5625 ] 2.5 = 3.052 , so Δ σ z = 14.9 / 3.052 = 4.9 kPa \Delta\sigma_z = 14.9/3.052 = 4.9\text{ kPa} Δ σ z = 14.9/3.052 = 4.9 kPa .
Westergaard directly below gives 500 / ( π ⋅ 16 ) = 9.9 kPa 500/(\pi \cdot 16) = 9.9\text{ kPa} 500/ ( π ⋅ 16 ) = 9.9 kPa , about two-thirds of the Boussinesq value.
Line load q q q (kN/m) at horizontal distance x x x :
Δ σ z = 2 q z 3 π ( x 2 + z 2 ) 2 \Delta\sigma_z = \frac{2qz^3}{\pi (x^2 + z^2)^2} Δ σ z = π ( x 2 + z 2 ) 2 2 q z 3
Approximate 2:1 Method
The load is assumed to spread at a slope of 2 vertical to 1 horizontal on each side. The loaded area therefore grows by z z z in each plan dimension:
Δ σ z = P ( B + z ) ( L + z ) = q B L ( B + z ) ( L + z ) \Delta\sigma_z = \frac{P}{(B + z)(L + z)} = \frac{qBL}{(B + z)(L + z)} Δ σ z = ( B + z ) ( L + z ) P = ( B + z ) ( L + z ) qB L
For a strip footing, Δ σ z = q B / ( B + z ) \Delta\sigma_z = qB/(B + z) Δ σ z = qB / ( B + z ) .
Example. A 2 × 3 m 2 \times 3\text{ m} 2 × 3 m footing carries q = 150 kPa q = 150\text{ kPa} q = 150 kPa . At z = 3 m z = 3\text{ m} z = 3 m below the base, Δ σ z = 150 ( 2 ) ( 3 ) / [ ( 5 ) ( 6 ) ] = 30 kPa \Delta\sigma_z = 150(2)(3)/[(5)(6)] = 30\text{ kPa} Δ σ z = 150 ( 2 ) ( 3 ) / [( 5 ) ( 6 )] = 30 kPa .
The 2:1 value is an average over the widened area. It is quick, but less accurate than the elastic solutions beneath the center at shallow depth.
Uniformly Loaded Circular Area
Below the center of a flexible circular area of radius R R R carrying uniform pressure q q q (tanks, silos):
Δ σ z = q [ 1 − 1 [ 1 + ( R / z ) 2 ] 3 / 2 ] \Delta\sigma_z = q\left[1 - \frac{1}{\left[1 + (R/z)^2\right]^{3/2}}\right] Δ σ z = q [ 1 − [ 1 + ( R / z ) 2 ] 3/2 1 ]
Example. An oil tank of radius 5 m applies q = 100 kPa q = 100\text{ kPa} q = 100 kPa . At z = 5 m z = 5\text{ m} z = 5 m , R / z = 1 R/z = 1 R / z = 1 , so Δ σ z = 100 [ 1 − 1 / 2 1.5 ] = 100 ( 1 − 0.3536 ) = 64.6 kPa \Delta\sigma_z = 100[1 - 1/2^{1.5}] = 100(1 - 0.3536) = 64.6\text{ kPa} Δ σ z = 100 [ 1 − 1/ 2 1.5 ] = 100 ( 1 − 0.3536 ) = 64.6 kPa .
Uniformly Loaded Rectangular Area
Below a corner of a flexible rectangle B × L B \times L B × L , Δ σ z = q I \Delta\sigma_z = qI Δ σ z = q I . The influence factor I I I depends on m = B / z m = B/z m = B / z and n = L / z n = L/z n = L / z . It is read from Fadum's chart or table, or computed from the integrated Boussinesq expression:
I = 1 4 π [ 2 m n m 2 + n 2 + 1 m 2 + n 2 + m 2 n 2 + 1 ⋅ m 2 + n 2 + 2 m 2 + n 2 + 1 + tan − 1 2 m n m 2 + n 2 + 1 m 2 + n 2 + 1 − m 2 n 2 ] I = \frac{1}{4\pi}\left[\frac{2mn\sqrt{m^2+n^2+1}}{m^2+n^2+m^2n^2+1}\cdot\frac{m^2+n^2+2}{m^2+n^2+1} + \tan^{-1}\frac{2mn\sqrt{m^2+n^2+1}}{m^2+n^2+1-m^2n^2}\right] I = 4 π 1 [ m 2 + n 2 + m 2 n 2 + 1 2 mn m 2 + n 2 + 1 ⋅ m 2 + n 2 + 1 m 2 + n 2 + 2 + tan − 1 m 2 + n 2 + 1 − m 2 n 2 2 mn m 2 + n 2 + 1 ]
When the denominator of the arctangent is negative, add π \pi π to the angle.
Superposition. To find stress below any other point, divide the loaded area into rectangles that each have a corner at that point. Then add their influence factors, subtracting any that lie outside the loaded area.
Example. A 4 × 6 m 4 \times 6\text{ m} 4 × 6 m raft applies q = 200 kPa q = 200\text{ kPa} q = 200 kPa . Find the stress increase at z = 4 m z = 4\text{ m} z = 4 m below the center.
Split the raft into four 2 × 3 m 2 \times 3\text{ m} 2 × 3 m rectangles that meet at the center.
For each, m = 2 / 4 = 0.5 m = 2/4 = 0.5 m = 2/4 = 0.5 and n = 3 / 4 = 0.75 n = 3/4 = 0.75 n = 3/4 = 0.75 , which gives I = 0.107 I = 0.107 I = 0.107 .
So Δ σ z = 4 ( 200 ) ( 0.107 ) = 85.7 kPa \Delta\sigma_z = 4(200)(0.107) = 85.7\text{ kPa} Δ σ z = 4 ( 200 ) ( 0.107 ) = 85.7 kPa .
The 2:1 method gives 200 ( 24 ) / ( 8 × 10 ) = 60 kPa 200(24)/(8 \times 10) = 60\text{ kPa} 200 ( 24 ) / ( 8 × 10 ) = 60 kPa at the same depth, an average rather than the center value.
Pressure bulbs. Under the center of a square footing, the stress increase falls to about 0.1 q 0.1q 0.1 q at a depth of about 2 B 2B 2 B . Under a long strip it falls to about 0.1 q 0.1q 0.1 q at roughly 6 B 6B 6 B . Soil investigation should reach these depths.
Newmark's Influence Chart
Newmark's chart draws concentric circles and radial lines so that each element contributes the same stress, typically an influence value of 0.005 0.005 0.005 (200 elements). To use it:
Draw the loaded area to a scale in which the chart's scale line equals the depth z z z .
Place the point of interest at the chart center.
Count the elements N N N covered by the area.
Δ σ z = q × ( influence value ) × N \Delta\sigma_z = q \times (\text{influence value}) \times N Δ σ z = q × ( influence value ) × N
Example. With N = 48 N = 48 N = 48 elements, q = 150 kPa q = 150\text{ kPa} q = 150 kPa and an influence value of 0.005, Δ σ z = 150 ( 0.005 ) ( 48 ) = 36 kPa \Delta\sigma_z = 150(0.005)(48) = 36\text{ kPa} Δ σ z = 150 ( 0.005 ) ( 48 ) = 36 kPa .
Average Stress Increase in a Clay Layer
For consolidation, use the average stress increase across the clay layer. With values at the top ( t t t ), middle ( m m m ) and bottom ( b b b ), Simpson's rule gives:
Δ σ av = Δ σ t + 4 Δ σ m + Δ σ b 6 \Delta\sigma_{\text{av}} = \frac{\Delta\sigma_t + 4\Delta\sigma_m + \Delta\sigma_b}{6} Δ σ av = 6 Δ σ t + 4Δ σ m + Δ σ b
Example. With 40, 25 and 15 kPa, Δ σ av = ( 40 + 100 + 15 ) / 6 = 25.8 kPa \Delta\sigma_{\text{av}} = (40 + 100 + 15)/6 = 25.8\text{ kPa} Δ σ av = ( 40 + 100 + 15 ) /6 = 25.8 kPa .
This value goes into the primary consolidation equations of Section 10.1. Using only the mid-depth value is a common simplification.
Immediate (Elastic) Settlement
Immediate settlement occurs as the load is applied, without volume change in saturated clay. It is the main settlement in sands. For a footing of width B B B on an elastic layer:
S e = q B ( 1 − μ 2 ) E s I s S_e = \frac{qB(1 - \mu^2)}{E_s}\,I_s S e = E s qB ( 1 − μ 2 ) I s
Here μ \mu μ is Poisson's ratio, E s E_s E s is the soil's elastic modulus, and I s I_s I s is an influence factor that depends on shape, rigidity and the point considered. For a square footing, I s I_s I s is about 1.12 1.12 1.12 at the center and 0.56 0.56 0.56 at the corner of a flexible footing, about 0.95 0.95 0.95 for its average, and about 0.82 0.82 0.82 for a rigid footing.
Example. A rigid 2.5 m 2.5\text{ m} 2.5 m square footing applies q = 180 kPa q = 180\text{ kPa} q = 180 kPa on sand with E s = 20 MPa E_s = 20\text{ MPa} E s = 20 MPa and μ = 0.3 \mu = 0.3 μ = 0.3 :
S e = 180 ( 2.5 ) ( 1 − 0.09 ) 20,000 ( 0.82 ) = 0.0168 m = 16.8 mm S_e = \frac{180(2.5)(1 - 0.09)}{20{,}000}(0.82) = 0.0168\text{ m} = 16.8\text{ mm} S e = 20 , 000 180 ( 2.5 ) ( 1 − 0.09 ) ( 0.82 ) = 0.0168 m = 16.8 mm
Secondary Compression
After excess pore pressure has dissipated, clays and organic soils keep compressing by creep of the soil skeleton:
S s = C α ′ H log t 2 t 1 , C α ′ = C α 1 + e p S_s = C_\alpha' H \log\frac{t_2}{t_1}, \qquad C_\alpha' = \frac{C_\alpha}{1 + e_p} S s = C α ′ H lo g t 1 t 2 , C α ′ = 1 + e p C α
Here:
- C α C_\alpha C α is the secondary compression index, the change in void ratio per log cycle of time;
- e p e_p e p is the void ratio at the end of primary consolidation;
t 1 t_1 t 1 is the time at the end of primary consolidation.
Example. A 4 m clay layer has C α = 0.02 C_\alpha = 0.02 C α = 0.02 and e p = 1.1 e_p = 1.1 e p = 1.1 , and primary consolidation ends at 2 years. Secondary settlement from 2 to 20 years is ( 0.02 / 2.1 ) ( 4 ) log 10 = 0.0381 m = 38.1 mm (0.02/2.1)(4)\log 10 = 0.0381\text{ m} = 38.1\text{ mm} ( 0.02/2.1 ) ( 4 ) lo g 10 = 0.0381 m = 38.1 mm .
Organic soils and peats have high C α C_\alpha C α , so secondary compression can exceed primary settlement in them.