Study guide

12.1 Axial Stress, Strain, and Deformation

PRC Civil Engineer Licensure Examination CELE

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Examination Overview, RA 544 & Professional Practice

1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice

2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics

2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum

3 Chapter 3: Engineering Data Analysis & Engineering Economy

3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis

4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying

4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves

5 Chapter 5: Highway & Transportation Engineering

5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems

6 Chapter 6: Construction Materials, Methods, Management & Safety

6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical

7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy

7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses

8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply

8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment

9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass

9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement

10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations

10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability

11 Chapter 11: Engineering Mechanics & Statics

11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members

12 Chapter 12: Strength of Materials

12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle

13 Chapter 13: Structural Analysis & NSCP Load Criteria

13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake

14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)

14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design

15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing

15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning

12.1 Axial Stress, Strain, and Deformation

Key Takeaways Explain This Topic AI

Normal stress ( σ = P / A \sigma = P/A σ = P / A ) and bearing stress ( σ b = P / A b \sigma_b = P/A_b σ b ​ = P / A b ​ ) quantify internal normal force intensities, where bearing area in bolted connections is taken strictly as the projected contact area A b = d ⋅ t A_b = d \cdot t A b ​ = d ⋅ t .

The stress-strain diagram for structural steel ( E = 200 GPa E = 200\text{ GPa} E = 200 GPa ) exhibits distinct physical regimes: linear elastic proportional zone, yield plateau, strain hardening, ultimate tensile strength ( σ u \sigma_u σ u ​ ), and localized necking prior to ductile rupture.

Axial deformation of prismatic homogeneous bars under Hooke's Law is governed by δ = P L A E \delta = \frac{P L}{A E} δ = A E P L ​ ; under self-weight or linearly distributed body force, total elongation is δ s w = W L 2 A E = γ L 2 2 E \delta_{sw} = \frac{W L}{2 A E} = \frac{\gamma L^2}{2 E} δ s w ​ = 2 A E W L ​ = 2 E γ L 2 ​ , exactly half that produced by an equal concentrated end load.

Statically indeterminate axial systems require coupling static equilibrium equations ( ∑ F = 0 \sum F = 0 ∑ F = 0 , ∑ M = 0 \sum M = 0 ∑ M = 0 ) with kinematic compatibility equations that enforce displacement boundary conditions.

Constrained thermal expansion induces thermal stress σ T = E α Δ T \sigma_T = E \alpha \Delta T σ T ​ = E α Δ T independent of member length; Poisson's ratio ( ν = − ϵ lat / ϵ long \nu = -\epsilon_{\text{lat}} / \epsilon_{\text{long}} ν = − ϵ lat ​ / ϵ long ​ ) couples orthogonal strains, governing volumetric strain e = Δ V V = σ x + σ y + σ z E ( 1 − 2 ν ) e = \frac{\Delta V}{V} = \frac{\sigma_x + \sigma_y + \sigma_z}{E}(1 - 2\nu) e = V Δ V ​ = E σ x ​ + σ y ​ + σ z ​ ​ ( 1 − 2 ν ) and bulk modulus K = E 3 ( 1 − 2 ν ) K = \frac{E}{3(1 - 2\nu)} K = 3 ( 1 − 2 ν ) E ​ .

Last updated: October 2026

12.1 Axial Stress, Strain, and Deformation

In structural mechanics, Strength of Materials (also termed Mechanics of Deformable Bodies) extends rigid-body statics by accounting for internal force intensities and physical material deformations. For civil engineers preparing for licensure examinations, axial stress, strain, and deformation constitute foundational principles tested extensively within structural analysis and design problems.

1. Normal Stress, Direct Shear, and Bearing Stress

When an external load acts collinear with the centroidal longitudinal axis of a prismatic member, it produces an internal normal force P P P distributed across the cross-sectional area A A A .

Axial Normal Stress ( σ \sigma σ )

Assuming the force acts through the centroid of the cross-section (Saint-Venant's Principle ensures uniform distribution beyond the immediate vicinity of load application points): σ = P A \sigma = \frac{P}{A} σ = A P ​

Tensile Stress ( + σ + \sigma + σ ): Tends to elongate the member.

Compressive Stress ( − σ - \sigma − σ ): Tends to shorten the member.

Units: In SI units, force is measured in Newtons ( N \text{N} N ) or kilonewtons ( kN \text{kN} kN ), area in square millimeters ( mm 2 \text{mm}^2 mm 2 ) or square meters ( m 2 \text{m}^2 m 2 ). Because 1 N/mm 2 = 1 MPa = 10 6 N/m 2 = 10 3 kPa 1\text{ N/mm}^2 = 1\text{ MPa} = 10^6\text{ N/m}^2 = 10^3\text{ kPa} 1 N/mm 2 = 1 MPa = 1 0 6 N/m 2 = 1 0 3 kPa , working in Newtons and millimeters yields stresses directly in megapascals ( MPa \text{MPa} MPa ).

Direct (Simple) Shear Stress ( τ \tau τ )

Direct shear occurs when transverse forces tend to slide one parallel plane of a material across another: τ avg = V A \tau_{\text{avg}} = \frac{V}{A} τ avg ​ = A V ​

Single Shear: A single cross-section of a bolt or pin resists shear force V = P V = P V = P ( A = π d 2 4 A = \frac{\pi d^2}{4} A = 4 π d 2 ​ ).

Double Shear: Two cross-sections simultaneously resist the applied load: V = P 2 V = \frac{P}{2} V = 2 P ​ , yielding τ avg = P 2 A \tau_{\text{avg}} = \frac{P}{2 A} τ avg ​ = 2 A P ​ .

Bearing Stress ( σ b \sigma_b σ b ​ )

Bearing stress is a localized compressive contact stress developed between two interacting solid bodies, such as a bolt shank pressing against the cylindrical wall of a connection plate hole. Because the actual contact pressure is non-uniformly distributed over the curved semi-cylindrical interface, engineering standards define bearing stress based on the projected contact area : σ b = P b A b = P b d ⋅ t \sigma_b = \frac{P_b}{A_b} = \frac{P_b}{d \cdot t} σ b ​ = A b ​ P b ​ ​ = d ⋅ t P b ​ ​ where d d d is the nominal diameter of the fastener and t t t is the thickness of the plate transmitting the force.

Stress Type Equation Resisting Area Definition Primary Failure Mode

Axial Tensile Stress σ = P / A net \sigma = P / A_{\text{net}} σ = P / A net ​ Net cross-sectional area after deducting holes ( A net = A g − ∑ d h t A_{\text{net}} = A_g - \sum d_h t A net ​ = A g ​ − ∑ d h ​ t ) Tensile rupture across net section

Direct Shear Stress τ = V / A v \tau = V / A_v τ = V / A v ​ Fastener cross-sectional shear plane area ( A v = m π d 2 4 A_v = m \frac{\pi d^2}{4} A v ​ = m 4 π d 2 ​ ) Fastener shear cleavage

Bearing Stress σ b = P / ( d ⋅ t ) \sigma_b = P / (d \cdot t) σ b ​ = P / ( d ⋅ t ) Projected rectangular area ( A b = d ⋅ t A_b = d \cdot t A b ​ = d ⋅ t ) Hole ovalization, plate crushing

  • 2. Normal Strain and the Stress-Strain Curve for Structural Steel
  • Normal Strain ( ϵ \epsilon ϵ )

Normal strain represents the non-dimensional ratio of elongation or contraction δ \delta δ to original unstrained gauge length L L L : ϵ = δ L = L f − L 0 L 0 ( mm/mm or μ ϵ ) \epsilon = \frac{\delta}{L} = \frac{L_f - L_0}{L_0} \quad (\text{mm/mm or } \mu\epsilon) ϵ = L δ ​ = L 0 ​ L f ​ − L 0 ​ ​ ( mm/mm or μ ϵ )

Engineering vs. True Stress and Strain

Engineering Stress ( σ eng = P / A 0 \sigma_{\text{eng}} = P / A_0 σ eng ​ = P / A 0 ​ ): Calculated using original un-deformed cross-sectional area A 0 A_0 A 0 ​ .

Engineering Strain ( ϵ eng = δ / L 0 \epsilon_{\text{eng}} = \delta / L_0 ϵ eng ​ = δ / L 0 ​ ): Calculated using original gauge length L 0 L_0 L 0 ​ .

True Stress ( σ true = P / A inst \sigma_{\text{true}} = P / A_{\text{inst}} σ true ​ = P / A inst ​ ): Calculated using instantaneous cross-sectional area A inst A_{\text{inst}} A inst ​ .

True Strain ( ϵ true = ln ⁡ ( L / L 0 ) = ln ⁡ ( 1 + ϵ eng ) \epsilon_{\text{true}} = \ln(L / L_0) = \ln(1 + \epsilon_{\text{eng}}) ϵ true ​ = ln ( L / L 0 ​ ) = ln ( 1 + ϵ eng ​ ) ).

Stress-Strain Diagram for Low-Carbon Structural Steel (ASTM A36)

A standard uniaxial tensile test on a ductile structural steel specimen generates a characteristic curve featuring six distinct behavioral zones:

Loading diagram...

Proportional Limit ( σ p l \sigma_{pl} σ pl ​ ): The maximum stress at which stress is directly proportional to strain. Hooke's Law remains strictly valid up to this threshold.

Elastic Limit ( σ e l \sigma_{el} σ e l ​ ): The maximum stress the material can sustain without experiencing permanent plastic deformation upon complete load release. For structural steel, σ e l ≈ σ p l \sigma_{el} \approx \sigma_{pl} σ e l ​ ≈ σ pl ​ .

Yield Point ( σ y \sigma_y σ y ​ ): The stress level at which a significant increase in strain occurs without any increase in tensile force. Structural steel exhibits an upper yield point followed by a lower yield plateau (nominally F y = 248 to 250 MPa F_y = 248\text{ to }250\text{ MPa} F y ​ = 248 to 250 MPa for ASTM A36 steel).

Strain Hardening: Beyond the yield plateau, atomic dislocations within the crystalline lattice tangle and block slip planes, requiring higher stress to produce further elongation until reaching the Ultimate Tensile Strength ( σ u ≈ 400 MPa \sigma_u \approx 400\text{ MPa} σ u ​ ≈ 400 MPa ) .

Necking and Rupture: Beyond σ u \sigma_u σ u ​ , localized cross-sectional contraction (necking) initiates. While true stress continues climbing, engineering stress drops until ductile fracture occurs at rupture stress σ f \sigma_f σ f ​ with a characteristic 45 ∘ 45^\circ 4 5 ∘ cup-and-cone shear lip.

Material Ductility Measures

Percent Elongation: % E L = L f − L 0 L 0 × 100 % \%EL = \frac{L_f - L_0}{L_0} \times 100\% % E L = L 0 ​ L f ​ − L 0 ​ ​ × 100% (structural steel typically achieves 20 % to 25 % 20\%\text{ to }25\% 20% to 25% ).

Percent Reduction in Area: % R A = A 0 − A f A 0 × 100 % \%RA = \frac{A_0 - A_f}{A_0} \times 100\% % R A = A 0 ​ A 0 ​ − A f ​ ​ × 100% (measures necking ductility, typically 40 % to 60 % 40\%\text{ to }60\% 40% to 60% ).

3. Hooke's Law and Axial Deformation Formulations

Within the linear elastic range below the proportional limit, Hooke's Law equates normal stress to strain via the Modulus of Elasticity (Young's Modulus, E E E ) : σ = E ϵ \sigma = E \epsilon σ = E ϵ For structural steel in metric SI units: E = 200 GPa = 200 , 000 MPa = 200 × 10 3 N/mm 2 E = 200\text{ GPa} = 200,000\text{ MPa} = 200 \times 10^3\text{ N/mm}^2 E = 200 GPa = 200 , 000 MPa = 200 × 1 0 3 N/mm 2 (or 29 × 10 6 psi 29 \times 10^6\text{ psi} 29 × 1 0 6 psi in Imperial units).

Axial Elongation of a Prismatic Bar

Substituting σ = P A \sigma = \frac{P}{A} σ = A P ​ and ϵ = δ L \epsilon = \frac{\delta}{L} ϵ = L δ ​ into Hooke's Law yields the classic deformation formula: P A = E ( δ L ) ⟹ δ = P L A E \frac{P}{A} = E \left(\frac{\delta}{L}\right) \implies \boxed{\delta = \frac{P L}{A E}} A P ​ = E ( L δ ​ ) ⟹ δ = A E P L ​ ​

Axial Stiffness: k = P δ = A E L k = \frac{P}{\delta} = \frac{A E}{L} k = δ P ​ = L A E ​ (force required to produce unit elongation, N/mm \text{N/mm} N/mm or kN/m \text{kN/m} kN/m ).

Axial Flexibility: f = 1 k = L A E f = \frac{1}{k} = \frac{L}{A E} f = k 1 ​ = A E L ​ (displacement produced by unit applied force).

Non-Prismatic Members and Continuously Distributed Axial Loads

For bars with variable cross-sectional area A ( x ) A(x) A ( x ) , internal force P ( x ) P(x) P ( x ) , or modulus E ( x ) E(x) E ( x ) , total elongation is obtained by integrating infinitesimal elements d x dx d x : δ = ∫ 0 L P ( x ) A ( x ) E ( x ) d x \delta = \int_0^L \frac{P(x)}{A(x) E(x)} \, dx δ = ∫ 0 L ​ A ( x ) E ( x ) P ( x ) ​ d x

Elongation Due to Self-Weight

For a vertical bar of uniform area A A A , length L L L , and unit weight γ = ρ g \gamma = \rho g γ = ρ g suspended from its top end, the internal axial tensile force at distance x x x from the free bottom tip is P ( x ) = γ A x P(x) = \gamma A x P ( x ) = γ A x . The total elongation is: δ s w = ∫ 0 L γ A x A E d x = γ E [ x 2 2 ] 0 L = γ L 2 2 E \delta_{sw} = \int_0^L \frac{\gamma A x}{A E} \, dx = \frac{\gamma}{E} \left[\frac{x^2}{2}\right]_0^L = \frac{\gamma L^2}{2 E} δ s w ​ = ∫ 0 L ​ A E γ A x ​ d x = E γ ​ [ 2 x 2 ​ ] 0 L ​ = 2 E γ L 2 ​ Expressing this in terms of total self-weight W = γ A L W = \gamma A L W = γ A L : δ s w = W L 2 A E \boxed{\delta_{sw} = \frac{W L}{2 A E}} δ s w ​ = 2 A E W L ​ ​

Important

The elongation of a uniform vertical member under its own self-weight is exactly half of the elongation produced by a concentrated end force equal to the total weight ( P = W P = W P = W ). The effective average internal force is W / 2 W/2 W /2 .

  • 4. Stepped Bars and Statically Indeterminate Axial Systems
  • Compound and Stepped Bars in Series

For a segmented shaft subjected to multiple point loads along its length, internal force P i P_i P i ​ within each segment is determined via the method of sections. Total deformation is the algebraic sum of individual segment displacements: δ total = ∑ i = 1 n P i L i A i E i \delta_{\text{total}} = \sum_{i=1}^n \frac{P_i L_i}{A_i E_i} δ total ​ = ∑ i = 1 n ​ A i ​ E i ​ P i ​ L i ​ ​

Statically Indeterminate Axial Systems

When the number of unknown support reactions exceeds the available equations of static equilibrium ( ∑ F = 0 , ∑ M = 0 \sum F = 0, \sum M = 0 ∑ F = 0 , ∑ M = 0 ), the structure is statically indeterminate . Solving requires establishing compatibility equations based on geometric displacement constraints.

Loading diagram...

5. Thermal Deformation and Constrained Thermal Stress

When a homogeneous isotropic material experiences a uniform temperature change Δ T = T final − T initial \Delta T = T_{\text{final}} - T_{\text{initial}} Δ T = T final ​ − T initial ​ , it undergoes thermal strain proportional to its Coefficient of Thermal Expansion ( α \alpha α ) : ϵ T = α Δ T \epsilon_T = \alpha \Delta T ϵ T ​ = α Δ T δ T = α L Δ T \delta_T = \alpha L \Delta T δ T ​ = αL Δ T Typical values: Structural steel α s ≈ 11.7 × 10 − 6 / ∘ C \alpha_s \approx 11.7 \times 10^{-6} / ^\circ\text{C} α s ​ ≈ 11.7 × 1 0 − 6 / ∘ C ( 6.5 × 10 − 6 / ∘ F 6.5 \times 10^{-6} / ^\circ\text{F} 6.5 × 1 0 − 6 / ∘ F ); concrete α c ≈ 10.0 × 10 − 6 / ∘ C \alpha_c \approx 10.0 \times 10^{-6} / ^\circ\text{C} α c ​ ≈ 10.0 × 1 0 − 6 / ∘ C ; bronze/brass α b ≈ 18.0 × 10 − 6 / ∘ C \alpha_b \approx 18.0 \times 10^{-6} / ^\circ\text{C} α b ​ ≈ 18.0 × 1 0 − 6 / ∘ C .

Constrained Thermal Stress

If a member is completely unconstrained, it expands or contracts freely without developing internal stress ( σ = 0 \sigma = 0 σ = 0 ). However, if supports prevent deformation: δ net = δ T − δ P = 0 ⟹ α L Δ T − P L A E = 0 \delta_{\text{net}} = \delta_T - \delta_P = 0 \implies \alpha L \Delta T - \frac{P L}{A E} = 0 δ net ​ = δ T ​ − δ P ​ = 0 ⟹ αL Δ T − A E P L ​ = 0 σ T = P A = E α Δ T \boxed{\sigma_T = \frac{P}{A} = E \alpha \Delta T} σ T ​ = A P ​ = E α Δ T ​

Note

The induced thermal stress in a fully constrained prismatic bar is completely independent of member length L L L and cross-sectional area A A A ; it depends solely on material properties ( E , α E, \alpha E , α ) and temperature differential Δ T \Delta T Δ T .

Initial Expansion Gaps ( Δ gap \Delta_{\text{gap}} Δ gap ​ )

If a clearance gap Δ gap \Delta_{\text{gap}} Δ gap ​ exists between the bar tip and a rigid stop:

If δ T ≤ Δ gap \delta_T \le \Delta_{\text{gap}} δ T ​ ≤ Δ gap ​ : The bar expands freely into the gap; σ T = 0 \sigma_T = 0 σ T ​ = 0 .

If δ T > Δ gap \delta_T > \Delta_{\text{gap}} δ T ​ > Δ gap ​ : The bar closes the gap and experiences compressive restraint: δ T − δ P = Δ gap ⟹ α L Δ T − σ T L E = Δ gap ⟹ σ T = E L ( α L Δ T − Δ gap ) \delta_T - \delta_P = \Delta_{\text{gap}} \implies \alpha L \Delta T - \frac{\sigma_T L}{E} = \Delta_{\text{gap}} \implies \sigma_T = \frac{E}{L}(\alpha L \Delta T - \Delta_{\text{gap}}) δ T ​ − δ P ​ = Δ gap ​ ⟹ αL Δ T − E σ T ​ L ​ = Δ gap ​ ⟹ σ T ​ = L E ​ ( αL Δ T − Δ gap ​ )

  • 6. Poisson's Ratio, Generalized Hooke's Law, and Volumetric Strain
  • Poisson's Ratio ( ν \nu ν )

When an axial tensile stress σ x \sigma_x σ x ​ elongates a bar in the longitudinal direction, the bar simultaneously contracts in all transverse (lateral) directions. Poisson's ratio ν \nu ν is the negative ratio of lateral strain to longitudinal strain: ν = − ϵ lateral ϵ longitudinal = − ϵ y ϵ x = − ϵ z ϵ x \nu = -\frac{\epsilon_{\text{lateral}}}{\epsilon_{\text{longitudinal}}} = -\frac{\epsilon_y}{\epsilon_x} = -\frac{\epsilon_z}{\epsilon_x} ν = − ϵ longitudinal ​ ϵ lateral ​ ​ = − ϵ x ​ ϵ y ​ ​ = − ϵ x ​ ϵ z ​ ​ For structural steel, ν ≈ 0.25 to 0.30 \nu \approx 0.25\text{ to }0.30 ν ≈ 0.25 to 0.30 . Theoretical bounds for stable isotropic materials are 0.0 ≤ ν ≤ 0.50 0.0 \le \nu \le 0.50 0.0 ≤ ν ≤ 0.50 (where ν = 0.50 \nu = 0.50 ν = 0.50 represents a perfectly incompressible material like saturated rubber or undrained clay).

Generalized Hooke's Law (3D Stress State)

Applying the principle of linear superposition for triaxial normal stresses ( σ x , σ y , σ z ) (\sigma_x, \sigma_y, \sigma_z) ( σ x ​ , σ y ​ , σ z ​ ) : ϵ x = 1 E [ σ x − ν ( σ y + σ z ) ] \epsilon_x = \frac{1}{E} [\sigma_x - \nu (\sigma_y + \sigma_z)] ϵ x ​ = E 1 ​ [ σ x ​ − ν ( σ y ​ + σ z ​ )] ϵ y = 1 E [ σ y − ν ( σ x + σ z ) ] \epsilon_y = \frac{1}{E} [\sigma_y - \nu (\sigma_x + \sigma_z)] ϵ y ​ = E 1 ​ [ σ y ​ − ν ( σ x ​ + σ z ​ )] ϵ z = 1 E [ σ z − ν ( σ x + σ y ) ] \epsilon_z = \frac{1}{E} [\sigma_z - \nu (\sigma_x + \sigma_y)] ϵ z ​ = E 1 ​ [ σ z ​ − ν ( σ x ​ + σ y ​ )]

Volumetric Strain (Dilation, e e e ) and Bulk Modulus ( K K K )

Volumetric strain represents the fractional change in volume of an elemental cuboid: e = Δ V V 0 = ( 1 + ϵ x ) ( 1 + ϵ y ) ( 1 + ϵ z ) − 1 ≈ ϵ x + ϵ y + ϵ z e = \frac{\Delta V}{V_0} = (1 + \epsilon_x)(1 + \epsilon_y)(1 + \epsilon_z) - 1 \approx \epsilon_x + \epsilon_y + \epsilon_z e = V 0 ​ Δ V ​ = ( 1 + ϵ x ​ ) ( 1 + ϵ y ​ ) ( 1 + ϵ z ​ ) − 1 ≈ ϵ x ​ + ϵ y ​ + ϵ z ​ Summing the three strain expressions: e = 1 − 2 ν E ( σ x + σ y + σ z ) e = \frac{1 - 2\nu}{E} (\sigma_x + \sigma_y + \sigma_z) e = E 1 − 2 ν ​ ( σ x ​ + σ y ​ + σ z ​ ) Under uniform hydrostatic pressure ( P hyd = − σ x = − σ y = − σ z P_{\text{hyd}} = -\sigma_x = -\sigma_y = -\sigma_z P hyd ​ = − σ x ​ = − σ y ​ = − σ z ​ ): e = − 3 ( 1 − 2 ν ) E P hyd ⟹ P hyd = − K e e = -\frac{3(1 - 2\nu)}{E} P_{\text{hyd}} \implies P_{\text{hyd}} = -K e e = − E 3 ( 1 − 2 ν ) ​ P hyd ​ ⟹ P hyd ​ = − Ke where the Bulk Modulus of Elasticity ( K K K ) is defined as: K = E 3 ( 1 − 2 ν ) \boxed{K = \frac{E}{3(1 - 2\nu)}} K = 3 ( 1 − 2 ν ) E ​ ​ Notice that as ν → 0.50 \nu \to 0.50 ν → 0.50 , K → ∞ K \to \infty K → ∞ and e → 0 e \to 0 e → 0 , confirming that incompressible materials undergo zero volumetric change under hydrostatic stress.

7. Stress Concentrations ( K t K_t K t ​ )

Abrupt geometric discontinuities—such as circular holes, fillets, grooves, or notches—disturb the uniform trajectory of stress trajectories, inducing high localized peak stresses σ max ⁡ \sigma_{\max} σ m a x ​ : K t = σ max ⁡ σ nom K_t = \frac{\sigma_{\max}}{\sigma_{\text{nom}}} K t ​ = σ nom ​ σ m a x ​ ​ where σ nom \sigma_{\text{nom}} σ nom ​ is the nominal average stress evaluated over the net reduced cross-sectional area.

For a wide plate with a small central circular hole under uniform axial tension: K t ≈ 3.0 K_t \approx 3.0 K t ​ ≈ 3.0 at the hole perimeter.

Ductile Materials (Structural Steel): Under static monotonic loading, localized stress concentrations are relieved by localized plastic yielding and stress redistribution; therefore, nominal stress governs static design ( K t K_t K t ​ is typically neglected in static steel tension member design).

Brittle Materials & Fatigue: Stress concentrations never redistribute elastically in brittle materials and trigger rapid crack propagation under cyclic fatigue loading; K t K_t K t ​ must be strictly applied.

8. Worked Example: Indeterminate Rigid Bar with Steel and Bronze Support Rods

Problem Statement: A rigid horizontal bar A B C ABC A BC of negligible mass is pinned to a support at A A A and supported by two vertical hanger rods: a bronze rod at B B B ( L b = 1.50 m , A b = 600 mm 2 , E b = 100 GPa , α b = 18.0 × 10 − 6 / ∘ C L_b = 1.50\text{ m}, A_b = 600\text{ mm}^2, E_b = 100\text{ GPa}, \alpha_b = 18.0 \times 10^{-6}/^\circ\text{C} L b ​ = 1.50 m , A b ​ = 600 mm 2 , E b ​ = 100 GPa , α b ​ = 18.0 × 1 0 − 6 / ∘ C ) attached 1.20 m 1.20\text{ m} 1.20 m from A A A , and a structural steel rod at C C C ( L s = 2.00 m , A s = 400 mm 2 , E s = 200 GPa , α s = 12.0 × 10 − 6 / ∘ C L_s = 2.00\text{ m}, A_s = 400\text{ mm}^2, E_s = 200\text{ GPa}, \alpha_s = 12.0 \times 10^{-6}/^\circ\text{C} L s ​ = 2.00 m , A s ​ = 400 mm 2 , E s ​ = 200 GPa , α s ​ = 12.0 × 1 0 − 6 / ∘ C ) attached 2.40 m 2.40\text{ m} 2.40 m from A A A . A downward vertical load of P = 72 kN P = 72\text{ kN} P = 72 kN is applied at point D D D , located 1.80 m 1.80\text{ m} 1.80 m from A A A . Simultaneously, the ambient temperature rises by Δ T = 30 ∘ C \Delta T = 30^\circ\text{C} Δ T = 3 0 ∘ C .

Determine (a) the tensile forces developed in both rods, and (b) the vertical deflection at point D D D .

Step-by-Step Solution:

Statics (Equilibrium): Taking moments about pin A A A ( ∑ M A = 0 \sum M_A = 0 ∑ M A ​ = 0 counterclockwise): P b ( 1.20 m ) + P s ( 2.40 m ) − P ( 1.80 m ) = 0 P_b (1.20\text{ m}) + P_s (2.40\text{ m}) - P (1.80\text{ m}) = 0 P b ​ ( 1.20 m ) + P s ​ ( 2.40 m ) − P ( 1.80 m ) = 0 1.20 P b + 2.40 P s = ( 72 kN ) ( 1.80 m ) = 129.6 kN ⋅ m 1.20 P_b + 2.40 P_s = (72\text{ kN})(1.80\text{ m}) = 129.6\text{ kN}\cdot\text{m} 1.20 P b ​ + 2.40 P s ​ = ( 72 kN ) ( 1.80 m ) = 129.6 kN ⋅ m Dividing by 1.20 1.20 1.20 : P b + 2 P s = 108.0 kN ⟹ P b = 108.0 − 2 P s — (Eq. 1) P_b + 2 P_s = 108.0\text{ kN} \quad \implies \quad P_b = 108.0 - 2 P_s \quad \text{--- (Eq. 1)} P b ​ + 2 P s ​ = 108.0 kN ⟹ P b ​ = 108.0 − 2 P s ​ — (Eq. 1)

Kinematic Compatibility (Rigid Bar Geometry): Because bar A B C ABC A BC is rigid and pinned at A A A , it rotates through a small angle θ \theta θ about A A A . Vertical downward displacements are linearly proportional to distance from A A A : δ B = 1.20 θ , δ C = 2.40 θ ⟹ δ C = 2 δ B — (Eq. 2) \delta_B = 1.20 \theta, \quad \delta_C = 2.40 \theta \implies \delta_C = 2 \delta_B \quad \text{--- (Eq. 2)} δ B ​ = 1.20 θ , δ C ​ = 2.40 θ ⟹ δ C ​ = 2 δ B ​ — (Eq. 2)

Constitutive Relations (Mechanical and Thermal Elongation): Total downward displacement at each rod connection point is the net elongation of the rod (tensile strain plus thermal expansion): δ B = P b L b A b E b + α b L b Δ T \delta_B = \frac{P_b L_b}{A_b E_b} + \alpha_b L_b \Delta T δ B ​ = A b ​ E b ​ P b ​ L b ​ ​ + α b ​ L b ​ Δ T δ C = P s L s A s E s + α s L s Δ T \delta_C = \frac{P_s L_s}{A_s E_s} + \alpha_s L_s \Delta T δ C ​ = A s ​ E s ​ P s ​ L s ​ ​ + α s ​ L s ​ Δ T

Evaluate Individual Thermal and Elastic Parameters:

Bronze Rod ( B B B ): A b E b = ( 600 mm 2 ) ( 100 × 10 3 N/mm 2 ) = 60.0 × 10 6 N = 60 , 000 kN A_b E_b = (600\text{ mm}^2)(100 \times 10^3\text{ N/mm}^2) = 60.0 \times 10^6\text{ N} = 60,000\text{ kN} A b ​ E b ​ = ( 600 mm 2 ) ( 100 × 1 0 3 N/mm 2 ) = 60.0 × 1 0 6 N = 60 , 000 kN L b A b E b = 1500 mm 60 , 000 kN = 0.0250 mm/kN \frac{L_b}{A_b E_b} = \frac{1500\text{ mm}}{60,000\text{ kN}} = 0.0250\text{ mm/kN} A b ​ E b ​ L b ​ ​ = 60 , 000 kN 1500 mm ​ = 0.0250 mm/kN δ T , b = α b L b Δ T = ( 18.0 × 10 − 6 / ∘ C ) ( 1500 mm ) ( 30 ∘ C ) = 0.810 mm \delta_{T,b} = \alpha_b L_b \Delta T = (18.0 \times 10^{-6}/^\circ\text{C})(1500\text{ mm})(30^\circ\text{C}) = 0.810\text{ mm} δ T , b ​ = α b ​ L b ​ Δ T = ( 18.0 × 1 0 − 6 / ∘ C ) ( 1500 mm ) ( 3 0 ∘ C ) = 0.810 mm δ B = 0.0250 P b + 0.810 mm \delta_B = 0.0250 P_b + 0.810\text{ mm} δ B ​ = 0.0250 P b ​ + 0.810 mm

Steel Rod ( C C C ): A s E s = ( 400 mm 2 ) ( 200 × 10 3 N/mm 2 ) = 80.0 × 10 6 N = 80 , 000 kN A_s E_s = (400\text{ mm}^2)(200 \times 10^3\text{ N/mm}^2) = 80.0 \times 10^6\text{ N} = 80,000\text{ kN} A s ​ E s ​ = ( 400 mm 2 ) ( 200 × 1 0 3 N/mm 2 ) = 80.0 × 1 0 6 N = 80 , 000 kN L s A s E s = 2000 mm 80 , 000 kN = 0.0250 mm/kN \frac{L_s}{A_s E_s} = \frac{2000\text{ mm}}{80,000\text{ kN}} = 0.0250\text{ mm/kN} A s ​ E s ​ L s ​ ​ = 80 , 000 kN 2000 mm ​ = 0.0250 mm/kN δ T , s = α s L s Δ T = ( 12.0 × 10 − 6 / ∘ C ) ( 2000 mm ) ( 30 ∘ C ) = 0.720 mm \delta_{T,s} = \alpha_s L_s \Delta T = (12.0 \times 10^{-6}/^\circ\text{C})(2000\text{ mm})(30^\circ\text{C}) = 0.720\text{ mm} δ T , s ​ = α s ​ L s ​ Δ T = ( 12.0 × 1 0 − 6 / ∘ C ) ( 2000 mm ) ( 3 0 ∘ C ) = 0.720 mm δ C = 0.0250 P s + 0.720 mm \delta_C = 0.0250 P_s + 0.720\text{ mm} δ C ​ = 0.0250 P s ​ + 0.720 mm

Substitute into Compatibility Condition (Eq. 2): δ C = 2 δ B \delta_C = 2 \delta_B δ C ​ = 2 δ B ​ 0.0250 P s + 0.720 = 2 ( 0.0250 P b + 0.810 ) = 0.0500 P b + 1.620 0.0250 P_s + 0.720 = 2 (0.0250 P_b + 0.810) = 0.0500 P_b + 1.620 0.0250 P s ​ + 0.720 = 2 ( 0.0250 P b ​ + 0.810 ) = 0.0500 P b ​ + 1.620 0.0250 P s − 0.0500 P b = 1.620 − 0.720 = 0.900 0.0250 P_s - 0.0500 P_b = 1.620 - 0.720 = 0.900 0.0250 P s ​ − 0.0500 P b ​ = 1.620 − 0.720 = 0.900 Dividing across by 0.0250 0.0250 0.0250 : P s − 2 P b = 36.0 kN ⟹ P s = 2 P b + 36.0 — (Eq. 3) P_s - 2 P_b = 36.0\text{ kN} \quad \implies \quad P_s = 2 P_b + 36.0 \quad \text{--- (Eq. 3)} P s ​ − 2 P b ​ = 36.0 kN ⟹ P s ​ = 2 P b ​ + 36.0 — (Eq. 3)

Solve Simultaneous Equations (Eq. 1 and Eq. 3): Substitute Eq. 1 into Eq. 3: P s = 2 ( 108.0 − 2 P s ) + 36.0 = 216.0 − 4 P s + 36.0 = 252.0 − 4 P s P_s = 2 (108.0 - 2 P_s) + 36.0 = 216.0 - 4 P_s + 36.0 = 252.0 - 4 P_s P s ​ = 2 ( 108.0 − 2 P s ​ ) + 36.0 = 216.0 − 4 P s ​ + 36.0 = 252.0 − 4 P s ​ 5 P s = 252.0 ⟹ P s = 50.4 kN 5 P_s = 252.0 \implies \boxed{P_s = 50.4\text{ kN}} 5 P s ​ = 252.0 ⟹ P s ​ = 50.4 kN ​ From Eq. 1: P b = 108.0 − 2 ( 50.4 ) = 7.20 kN \boxed{P_b = 108.0 - 2(50.4) = 7.20\text{ kN}} P b ​ = 108.0 − 2 ( 50.4 ) = 7.20 kN ​

Compute Deflection at Load Point D D D ( x D = 1.80 m x_D = 1.80\text{ m} x D ​ = 1.80 m ): δ B = 0.0250 ( 7.20 ) + 0.810 = 0.180 + 0.810 = 0.990 mm \delta_B = 0.0250 (7.20) + 0.810 = 0.180 + 0.810 = 0.990\text{ mm} δ B ​ = 0.0250 ( 7.20 ) + 0.810 = 0.180 + 0.810 = 0.990 mm δ C = 0.0250 ( 50.40 ) + 0.720 = 1.260 + 0.720 = 1.980 mm \delta_C = 0.0250 (50.40) + 0.720 = 1.260 + 0.720 = 1.980\text{ mm} δ C ​ = 0.0250 ( 50.40 ) + 0.720 = 1.260 + 0.720 = 1.980 mm (Verification: δ C / δ B = 1.980 / 0.990 = 2.000 \delta_C / \delta_B = 1.980 / 0.990 = 2.000 δ C ​ / δ B ​ = 1.980/0.990 = 2.000 , confirming exact compatibility!) Rotation angle θ = δ B 1200 mm = 0.990 1200 = 0.000825 rad \theta = \frac{\delta_B}{1200\text{ mm}} = \frac{0.990}{1200} = 0.000825\text{ rad} θ = 1200 mm δ B ​ ​ = 1200 0.990 ​ = 0.000825 rad . δ D = θ × 1800 mm = 0.000825 × 1800 = 1.485 mm \boxed{\delta_D = \theta \times 1800\text{ mm} = 0.000825 \times 1800 = 1.485\text{ mm}} δ D ​ = θ × 1800 mm = 0.000825 × 1800 = 1.485 mm ​

9. CELE Board Exam Traps & Common Computational Errors

Warning

Trap 1: Thermal Stress Direction: When temperature rises ( Δ T > 0 \Delta T > 0 Δ T > 0 ), a constrained member tries to expand. The rigid constraints push back inward, inducing compressive stress (negative normal force). Never report positive tensile stress for constrained thermal expansion.

Warning

Trap 2: Self-Weight Elongation Omission of Factor 2: Total elongation of a suspended bar under its own weight is δ = W L 2 A E \delta = \frac{W L}{2 A E} δ = 2 A E W L ​ , not W L A E \frac{W L}{A E} A E W L ​ . Forgetting the divisor 2 overstates self-weight elongation by exactly 100 % 100\% 100% .

Warning

Trap 3: Bearing Area vs. Shear Area in Connections: For a pinned or bolted joint, bearing stress uses the projected contact rectangle ( A b = d ⋅ t A_b = d \cdot t A b ​ = d ⋅ t ), whereas bolt shear stress uses the circular cross-sectional area ( A v = π d 2 4 A_v = \frac{\pi d^2}{4} A v ​ = 4 π d 2 ​ ). Mixing these areas in connection capacity checks is a frequent source of error.

Loading diagram... Kinematic Compatibility and Equilibrium for a Supported Rigid Beam System