Study guide
12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
Key Takeaways Explain This Topic AI
Elastic beam deflections are determined through the Double Integration Method ( E I d 2 y d x 2 = M ( x ) E I \frac{d^2 y}{dx^2} = M(x) E I d x 2 d 2 y = M ( x ) ), Moment-Area Theorems ( θ B / A = Area M / E I \theta_{B/A} = \text{Area}_{M/EI} θ B / A = Area M / E I ; t B / A = Area M / E I ⋅ x ˉ B t_{B/A} = \text{Area}_{M/EI} \cdot \bar{x}_B t B / A = Area M / E I ⋅ x ˉ B ), and the Conjugate Beam Method ( V conj = θ , M conj = y V_{\text{conj}} = \theta, M_{\text{conj}} = y V conj = θ , M conj = y ).
Combined axial force and bending induces normal stress σ = P A ± M c I \sigma = \frac{P}{A} \pm \frac{M c}{I} σ = A P ± I M c ; to prevent tensile stress from developing across a compressive cross-section, load eccentricity must remain within the kern (middle-third rule e ≤ h / 6 e \le h/6 e ≤ h /6 for rectangles, middle-quarter rule e ≤ d / 8 e \le d/8 e ≤ d /8 for solid circles).
Analytical stress transformation yields principal stresses σ 1 , 2 = σ x + σ y 2 ± ( σ x − σ y 2 ) 2 + τ x y 2 \sigma_{1,2} = \frac{\sigma_x + \sigma_y}{2} \pm \sqrt{(\frac{\sigma_x - \sigma_y}{2})^2 + \tau_{xy}^2} σ 1 , 2 = 2 σ x + σ y ± ( 2 σ x − σ y ) 2 + τ x y 2 on orthogonal planes oriented at tan 2 θ p = 2 τ x y σ x − σ y \tan 2\theta_p = \frac{2\tau_{xy}}{\sigma_x - \sigma_y} tan 2 θ p = σ x − σ y 2 τ x y , where shear stress vanishes identically.
Maximum in-plane shear stress is τ max , in-plane = ( σ x − σ y 2 ) 2 + τ x y 2 = σ 1 − σ 2 2 \tau_{\max, \text{in-plane}} = \sqrt{(\frac{\sigma_x - \sigma_y}{2})^2 + \tau_{xy}^2} = \frac{\sigma_1 - \sigma_2}{2} τ m a x , in-plane = ( 2 σ x − σ y ) 2 + τ x y 2 = 2 σ 1 − σ 2 ; absolute maximum shear stress equals σ 1 − σ 2 2 \frac{\sigma_1 - \sigma_2}{2} 2 σ 1 − σ 2 when principal stresses have opposite signs, but equals max ( ∣ σ 1 ∣ , ∣ σ 2 ∣ ) 2 \frac{\max(|\sigma_1|, |\sigma_2|)}{2} 2 m a x ( ∣ σ 1 ∣ , ∣ σ 2 ∣ ) when both non-zero principal stresses have identical signs.
Mohr's Circle geometrically maps plane stress with center C = ( σ x + σ y 2 , 0 ) C = (\frac{\sigma_x + \sigma_y}{2}, 0) C = ( 2 σ x + σ y , 0 ) and radius R = τ max , in-plane R = \tau_{\max, \text{in-plane}} R = τ m a x , in-plane ; yield failure is evaluated using Maximum Normal Stress (Rankine), Tresca (maximum shear: τ max ≥ σ y / 2 \tau_{\max} \ge \sigma_y / 2 τ m a x ≥ σ y /2 ), and von Mises (distortion energy: σ v = σ 1 2 − σ 1 σ 2 + σ 2 2 ≥ σ y \sigma_v = \sqrt{\sigma_1^2 - \sigma_1 \sigma_2 + \sigma_2^2} \ge \sigma_y σ v = σ 1 2 − σ 1 σ 2 + σ 2 2 ≥ σ y ).
Last updated: October 2026
12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
Advanced structural design requires verifying both serviceability (deflection limitations under operational loads) and ultimate strength under multi-axial stress states. This section explores classical beam deflection methods, eccentric combined loading, analytical stress transformation, Mohr's Circle, and failure theories.
1. Beam Deflection: Double Integration Method
From the differential geometry of beam curvature κ = d 2 y / d x 2 [ 1 + ( d y / d x ) 2 ] 3 / 2 ≈ d 2 y d x 2 \kappa = \frac{d^2 y / dx^2}{[1 + (dy/dx)^2]^{3/2}} \approx \frac{d^2 y}{dx^2} κ = [ 1 + ( d y / d x ) 2 ] 3/2 d 2 y / d x 2 ≈ d x 2 d 2 y (valid for small slopes d y / d x ≪ 1 dy/dx \ll 1 d y / d x ≪ 1 ), equating curvature to flexural moment yields the Euler-Bernoulli beam differential equation : E I d 2 y d x 2 = M ( x ) \boxed{E I \frac{d^2 y}{dx^2} = M(x)} E I d x 2 d 2 y = M ( x ) Integrating sequentially:
Slope Equation ( θ \theta θ ): E I d y d x = E I θ ( x ) = ∫ M ( x ) d x + C 1 E I \frac{dy}{dx} = E I \theta(x) = \int M(x) \, dx + C_1 E I d x d y = E I θ ( x ) = ∫ M ( x ) d x + C 1
Deflection Equation ( y y y ): E I y ( x ) = ∫ [ ∫ M ( x ) d x ] d x + C 1 x + C 2 E I y(x) = \int \left[\int M(x) \, dx\right] dx + C_1 x + C_2 E I y ( x ) = ∫ [ ∫ M ( x ) d x ] d x + C 1 x + C 2
Boundary Conditions for Integration Constants
Simply Supported (Pin or Roller at x = 0 x = 0 x = 0 ): y ( 0 ) = 0 y(0) = 0 y ( 0 ) = 0 .
Fixed Support (Built-in at x = 0 x = 0 x = 0 ): y ( 0 ) = 0 y(0) = 0 y ( 0 ) = 0 and θ ( 0 ) = d y d x ∣ x = 0 = 0 \theta(0) = \frac{dy}{dx}\big|_{x=0} = 0 θ ( 0 ) = d x d y x = 0 = 0 .
Symmetry (Midspan x = L / 2 x = L/2 x = L /2 of symmetric loading): θ ( L / 2 ) = 0 \theta(L/2) = 0 θ ( L /2 ) = 0 .
Free Cantilever End (at x = L x = L x = L ): Shear V ( L ) = 0 V(L) = 0 V ( L ) = 0 , Moment M ( L ) = 0 M(L) = 0 M ( L ) = 0 .
2. Moment-Area Theorems (Mohr's Theorems)
Developed by Christian Otto Mohr, the Moment-Area Theorems provide powerful geometric shortcuts for evaluating slopes and deflections without full algebraic integration.
First Moment-Area Theorem
The change in slope between any two points A A A and B B B on the elastic curve equals the total area under the M / ( E I ) M / (E I) M / ( E I ) diagram between those points: θ B / A = θ B − θ A = ∫ A B M ( x ) E I d x = Area of ( M E I ) A → B \boxed{\theta_{B/A} = \theta_B - \theta_A = \int_A^B \frac{M(x)}{E I} \, dx = \text{Area of } \left(\frac{M}{E I}\right)_{A \to B}} θ B / A = θ B − θ A = ∫ A B E I M ( x ) d x = Area of ( E I M ) A → B
Second Moment-Area Theorem
The vertical tangential deviation t B / A t_{B/A} t B / A of point B B B on the elastic curve relative to the tangent drawn from point A A A equals the first moment of the area under the M / ( E I ) M / (E I) M / ( E I ) diagram between A A A and B B B , taken about point B B B : t B / A = ∫ A B M ( x ) E I ( x B − x ) d x = [ Area of ( M E I ) A → B ] ⋅ x ˉ B \boxed{t_{B/A} = \int_A^B \frac{M(x)}{E I} (x_B - x) \, dx = \left[\text{Area of } \left(\frac{M}{E I}\right)_{A \to B}\right] \cdot \bar{x}_B} t B / A = ∫ A B E I M ( x ) ( x B − x ) d x = [ Area of ( E I M ) A → B ] ⋅ x ˉ B where x ˉ B \bar{x}_B x ˉ B is the centroidal distance of the M / ( E I ) M / (E I) M / ( E I ) area measured from reference point B B B .
Important
Tangential Deviation Directionality: Note that t B / A ≠ t A / B t_{B/A} \ne t_{A/B} t B / A = t A / B . t B / A t_{B/A} t B / A is the vertical distance from point B B B on the deflected curve to the tangent drawn from A A A ; the moment of the area is taken about point B B B .
3. The Conjugate Beam Method
The Conjugate Beam Method transforms deflection analysis into an equivalent statics problem by establishing a fictitious beam of identical span loaded with the real beam's M / ( E I ) M / (E I) M / ( E I ) diagram.
Fundamental Principles
Slope in Real Beam: Equals vertical shear force in the conjugate beam: θ real = V conj \theta_{\text{real}} = V_{\text{conj}} θ real = V conj .
Deflection in Real Beam: Equals bending moment in the conjugate beam: y real = M conj y_{\text{real}} = M_{\text{conj}} y real = M conj .
Real vs. Conjugate Support Conversions
Conjugate beam supports must satisfy boundary kinematic constraints:
Real Beam Boundary Condition Physical Slope & Deflection Conjugate Beam Support Conjugate Shear & Moment
Simple Pin / Roller End θ ≠ 0 , y = 0 \theta \ne 0, \; y = 0 θ = 0 , y = 0 Simple Pin / Roller End V ≠ 0 , M = 0 V \ne 0, \; M = 0 V = 0 , M = 0
Fixed (Built-in) Support θ = 0 , y = 0 \theta = 0, \; y = 0 θ = 0 , y = 0 Free End V = 0 , M = 0 V = 0, \; M = 0 V = 0 , M = 0
Free End (Cantilever tip) θ ≠ 0 , y ≠ 0 \theta \ne 0, \; y \ne 0 θ = 0 , y = 0 Fixed Support V ≠ 0 , M ≠ 0 V \ne 0, \; M \ne 0 V = 0 , M = 0
Internal Continuous Support θ \theta θ continuous, y = 0 y = 0 y = 0 Internal Hinge V V V continuous, M = 0 M = 0 M = 0
Internal Hinge θ \theta θ discontinuous, y ≠ 0 y \ne 0 y = 0 Internal Roller Support V V V discontinuous, M ≠ 0 M \ne 0 M = 0
4. Superposition Method for Standard Beam Cases
Linear elasticity permits superimposing slopes and deflections from standard loading cases:
Case & Loading Maximum Slope ( θ max \theta_{\max} θ m a x ) Maximum Deflection ( δ max \delta_{\max} δ m a x )
Cantilever: Concentrated Tip Load P P P θ max = P L 2 2 E I \theta_{\max} = \frac{P L^2}{2 E I} θ m a x = 2 E I P L 2 (at tip) δ max = P L 3 3 E I \delta_{\max} = \frac{P L^3}{3 E I} δ m a x = 3 E I P L 3 (at tip)
Cantilever: Uniform Load w w w θ max = w L 3 6 E I \theta_{\max} = \frac{w L^3}{6 E I} θ m a x = 6 E I w L 3 (at tip) δ max = w L 4 8 E I \delta_{\max} = \frac{w L^4}{8 E I} δ m a x = 8 E I w L 4 (at tip)
Simply Supported: Center Point Load P P P θ end = P L 2 16 E I \theta_{\text{end}} = \frac{P L^2}{16 E I} θ end = 16 E I P L 2 (at supports) δ max = P L 3 48 E I \delta_{\max} = \frac{P L^3}{48 E I} δ m a x = 48 E I P L 3 (at midspan)
Simply Supported: Uniform Load w w w θ end = w L 3 24 E I \theta_{\text{end}} = \frac{w L^3}{24 E I} θ end = 24 E I w L 3 (at supports) δ max = 5 w L 4 384 E I \delta_{\max} = \frac{5 w L^4}{384 E I} δ m a x = 384 E I 5 w L 4 (at midspan)
5. Combined Stresses: Axial Load Plus Bending and the Kern
When a member is subjected to combined axial normal force P P P and bending moment M M M (or an eccentric axial force P P P applied at eccentricity e e e from the centroid where M = P e M = P e M = P e ): σ = P A ± M c I = P A ( 1 ± e c r 2 ) \sigma = \frac{P}{A} \pm \frac{M c}{I} = \frac{P}{A} \left(1 \pm \frac{e c}{r^2}\right) σ = A P ± I M c = A P ( 1 ± r 2 ec ) where r = I / A r = \sqrt{I/A} r = I / A is the radius of gyration .
The Core / Kern of a Cross-Section
In masonry, unreinforced concrete, and precast post-tensioned members, materials possess negligible tensile strength. The kern is the central region of the cross-section within which an axial compressive force can be applied without generating tensile stress anywhere across the section.
Rectangular Cross-Section ( b × h b \times h b × h ): σ min = − P b h + P e y ( h / 2 ) b h 3 / 12 = − P A ( 1 − 6 e y h ) ≥ 0 ⟹ e y ≤ h 6 \sigma_{\min} = -\frac{P}{b h} + \frac{P e_y (h/2)}{b h^3 / 12} = -\frac{P}{A}\left(1 - \frac{6 e_y}{h}\right) \ge 0 \implies \boxed{e_y \le \frac{h}{6}} σ m i n = − bh P + b h 3 /12 P e y ( h /2 ) = − A P ( 1 − h 6 e y ) ≥ 0 ⟹ e y ≤ 6 h This is the famous Middle-Third Rule : to prevent tension, the resultant compressive force must fall within the middle third of the depth (total kern width = 2 ( h / 6 ) = h / 3 = 2(h/6) = h/3 = 2 ( h /6 ) = h /3 ). For biaxial eccentricities, the kern forms a diamond (rhombus) with diagonals h / 3 h/3 h /3 and b / 3 b/3 b /3 .
Solid Circular Cross-Section ( d d d ): σ min = − P A + P e ( d / 2 ) π d 4 / 64 = − P A ( 1 − 8 e d ) ≥ 0 ⟹ e ≤ d 8 = r 4 \sigma_{\min} = -\frac{P}{A} + \frac{P e (d/2)}{\pi d^4 / 64} = -\frac{P}{A}\left(1 - \frac{8 e}{d}\right) \ge 0 \implies \boxed{e \le \frac{d}{8} = \frac{r}{4}} σ m i n = − A P + π d 4 /64 P e ( d /2 ) = − A P ( 1 − d 8 e ) ≥ 0 ⟹ e ≤ 8 d = 4 r This constitutes the Middle-Quarter Rule : the kern is a concentric circle of diameter d / 4 d/4 d /4 .
6. Plane Stress Transformation Equations
Consider an element in a state of plane stress subjected to normal stresses ( σ x , σ y ) (\sigma_x, \sigma_y) ( σ x , σ y ) and shear stress τ x y \tau_{xy} τ x y . On an inclined plane oriented at angle θ \theta θ counterclockwise from the positive x x x -axis: σ x ′ = σ x + σ y 2 + ( σ x − σ y 2 ) cos 2 θ + τ x y sin 2 θ \boxed{\sigma_{x'} = \frac{\sigma_x + \sigma_y}{2} + \left(\frac{\sigma_x - \sigma_y}{2}\right) \cos 2\theta + \tau_{xy} \sin 2\theta} σ x ′ = 2 σ x + σ y + ( 2 σ x − σ y ) cos 2 θ + τ x y sin 2 θ τ x ′ y ′ = − ( σ x − σ y 2 ) sin 2 θ + τ x y cos 2 θ \boxed{\tau_{x'y'} = - \left(\frac{\sigma_x - \sigma_y}{2}\right) \sin 2\theta + \tau_{xy} \cos 2\theta} τ x ′ y ′ = − ( 2 σ x − σ y ) sin 2 θ + τ x y cos 2 θ σ y ′ = σ x + σ y 2 − ( σ x − σ y 2 ) cos 2 θ − τ x y sin 2 θ \sigma_{y'} = \frac{\sigma_x + \sigma_y}{2} - \left(\frac{\sigma_x - \sigma_y}{2}\right) \cos 2\theta - \tau_{xy} \sin 2\theta σ y ′ = 2 σ x + σ y − ( 2 σ x − σ y ) cos 2 θ − τ x y sin 2 θ
Stress Invariant
The sum of normal stresses on any two mutually perpendicular planes is constant: σ x ′ + σ y ′ = σ x + σ y = I 1 \sigma_{x'} + \sigma_{y'} = \sigma_x + \sigma_y = I_1 σ x ′ + σ y ′ = σ x + σ y = I 1
- 7. Principal Stresses and Maximum Shear Stress
- Principal Planes and Principal Stresses
Differentiating σ x ′ \sigma_{x'} σ x ′ with respect to θ \theta θ and setting to zero yields the principal planes where normal stresses reach their extrema: tan 2 θ p = 2 τ x y σ x − σ y \boxed{\tan 2\theta_p = \frac{2 \tau_{xy}}{\sigma_x - \sigma_y}} tan 2 θ p = σ x − σ y 2 τ x y
Note
On the principal planes, shearing stress is identically zero ( τ = 0 \tau = 0 τ = 0 ).
Substituting θ p \theta_p θ p into the transformation equations yields the principal normal stresses : σ 1 , 2 = σ x + σ y 2 ± ( σ x − σ y 2 ) 2 + τ x y 2 \boxed{\sigma_{1, 2} = \frac{\sigma_x + \sigma_y}{2} \pm \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2}} σ 1 , 2 = 2 σ x + σ y ± ( 2 σ x − σ y ) 2 + τ x y 2
Maximum In-Plane Shear Stress
Differentiating τ x ′ y ′ \tau_{x'y'} τ x ′ y ′ with respect to θ \theta θ yields the planes of maximum in-plane shear, oriented at 45 ∘ 45^\circ 4 5 ∘ to the principal planes: tan 2 θ s = − σ x − σ y 2 τ x y = − 1 tan 2 θ p \tan 2\theta_s = -\frac{\sigma_x - \sigma_y}{2 \tau_{xy}} = -\frac{1}{\tan 2\theta_p} tan 2 θ s = − 2 τ x y σ x − σ y = − t a n 2 θ p 1 τ max , in-plane = ( σ x − σ y 2 ) 2 + τ x y 2 = σ 1 − σ 2 2 \boxed{\tau_{\max, \text{in-plane}} = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2} = \frac{\sigma_1 - \sigma_2}{2}} τ m a x , in-plane = ( 2 σ x − σ y ) 2 + τ x y 2 = 2 σ 1 − σ 2 On these maximum shear planes, a uniform normal stress acts: σ avg = σ x + σ y 2 \sigma_{\text{avg}} = \frac{\sigma_x + \sigma_y}{2} σ avg = 2 σ x + σ y .
Absolute Maximum Shear Stress (3D Analysis)
In plane stress, the third principal stress perpendicular to the plane is zero: σ 3 = 0 \sigma_3 = 0 σ 3 = 0 .
Opposite Signs ( σ 1 > 0 \sigma_1 > 0 σ 1 > 0 and σ 2 < 0 \sigma_2 < 0 σ 2 < 0 ): τ max , abs = σ 1 − σ 2 2 = τ max , in-plane \tau_{\max, \text{abs}} = \frac{\sigma_1 - \sigma_2}{2} = \tau_{\max, \text{in-plane}} τ m a x , abs = 2 σ 1 − σ 2 = τ m a x , in-plane
Same Signs (Both Tensile: σ 1 ≥ σ 2 > 0 \sigma_1 \ge \sigma_2 > 0 σ 1 ≥ σ 2 > 0 ): τ max , abs = σ 1 − σ 3 2 = σ 1 − 0 2 = σ 1 2 \boxed{\tau_{\max, \text{abs}} = \frac{\sigma_1 - \sigma_3}{2} = \frac{\sigma_1 - 0}{2} = \frac{\sigma_1}{2}} τ m a x , abs = 2 σ 1 − σ 3 = 2 σ 1 − 0 = 2 σ 1
Same Signs (Both Compressive: σ 2 ≤ σ 1 < 0 \sigma_2 \le \sigma_1 < 0 σ 2 ≤ σ 1 < 0 ): τ max , abs = σ 3 − σ 2 2 = 0 − σ 2 2 = ∣ σ 2 ∣ 2 \tau_{\max, \text{abs}} = \frac{\sigma_3 - \sigma_2}{2} = \frac{0 - \sigma_2}{2} = \frac{|\sigma_2|}{2} τ m a x , abs = 2 σ 3 − σ 2 = 2 0 − σ 2 = 2 ∣ σ 2 ∣
8. Mohr's Circle for Plane Stress
Mohr's Circle graphically represents plane stress transformation. Squaring and adding the transformation equations yields the equation of a circle: ( σ x ′ − σ avg ) 2 + τ x ′ y ′ 2 = R 2 (\sigma_{x'} - \sigma_{\text{avg}})^2 + \tau_{x'y'}^2 = R^2 ( σ x ′ − σ avg ) 2 + τ x ′ y ′ 2 = R 2 .
Loading diagram...
Center of Circle: C = ( σ avg , 0 ) = ( σ x + σ y 2 , 0 ) C = (\sigma_{\text{avg}}, 0) = \left(\frac{\sigma_x + \sigma_y}{2}, 0\right) C = ( σ avg , 0 ) = ( 2 σ x + σ y , 0 ) .
Radius of Circle: R = ( σ x − σ y 2 ) 2 + τ x y 2 = τ max , in-plane R = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2} = \tau_{\max, \text{in-plane}} R = ( 2 σ x − σ y ) 2 + τ x y 2 = τ m a x , in-plane .
Angular Relation: A physical rotation of angle θ \theta θ on the stress element corresponds to a rotation of 2 θ 2\theta 2 θ in the same direction on Mohr's circle.
9. Classical Failure Theories
To predict yielding or fracture under multiaxial stress, engineers apply failure criteria calibrated against uniaxial yield strength ( F y = σ y F_y = \sigma_y F y = σ y ) or ultimate strength ( σ u \sigma_u σ u ):
Failure Theory Formulation Governing Criterion Recommended Applications
Maximum Normal Stress Theory (Rankine) ∣ σ 1 ∣ ≥ σ u \lvert\sigma_1\rvert \ge \sigma_u ∣ σ 1 ∣ ≥ σ u or ∣ σ 2 ∣ ≥ σ u \lvert\sigma_2\rvert \ge \sigma_u ∣ σ 2 ∣ ≥ σ u Failure occurs when maximum principal normal stress reaches uniaxial ultimate strength Brittle materials (plain concrete, cast iron, masonry)
Maximum Shear Stress Theory (Tresca) τ max , abs ≥ σ y 2 ⟹ max ( ∣ σ 1 − σ 2 ∣ , ∣ σ 1 ∣ , ∣ σ 2 ∣ ) ≥ σ y \tau_{\max, \text{abs}} \ge \frac{\sigma_y}{2} \implies \max(\lvert\sigma_1 - \sigma_2\rvert, \lvert\sigma_1\rvert, \lvert\sigma_2\rvert) \ge \sigma_y τ m a x , abs ≥ 2 σ y ⟹ max (∣ σ 1 − σ 2 ∣ , ∣ σ 1 ∣ , ∣ σ 2 ∣) ≥ σ y Yielding occurs when absolute maximum shear stress reaches shear yield strength Ductile materials (conservative design benchmark for structural steel)
Distortion Energy Theory (von Mises) σ v = σ 1 2 − σ 1 σ 2 + σ 2 2 = σ x 2 − σ x σ y + σ y 2 + 3 τ x y 2 ≥ σ y \sigma_v = \sqrt{\sigma_1^2 - \sigma_1 \sigma_2 + \sigma_2^2} = \sqrt{\sigma_x^2 - \sigma_x \sigma_y + \sigma_y^2 + 3\tau_{xy}^2} \ge \sigma_y σ v = σ 1 2 − σ 1 σ 2 + σ 2 2 = σ x 2 − σ x σ y + σ y 2 + 3 τ x y 2 ≥ σ y Yielding occurs when distortion strain energy per unit volume reaches the uniaxial yield threshold Ductile materials (most accurate predictor for structural steel and aluminum)
10. Worked Example: Combined Stresses, Principal Planes, and Mohr's Circle Analysis
Problem Statement: A solid cylindrical steel shaft of diameter d = 80 mm d = 80\text{ mm} d = 80 mm is subjected to a simultaneous axial tensile force of P = 150 kN P = 150\text{ kN} P = 150 kN , a bending moment M = 3.20 kN ⋅ m M = 3.20\text{ kN}\cdot\text{m} M = 3.20 kN ⋅ m , and a torsional torque T = 4.00 kN ⋅ m T = 4.00\text{ kN}\cdot\text{m} T = 4.00 kN ⋅ m .
Determine the state of stress ( σ x , σ y , τ x y ) (\sigma_x, \sigma_y, \tau_{xy}) ( σ x , σ y , τ x y ) at the critical point on the top surface of the shaft.
Calculate the principal stresses and orientation of the principal planes.
Calculate the maximum in-plane shear stress and absolute maximum shear stress.
Evaluate safety against yielding under the von Mises criterion if yield strength is σ y = 300 MPa \sigma_y = 300\text{ MPa} σ y = 300 MPa .
Step-by-Step Solution:
Cross-Section Properties: A = π d 2 4 = π ( 80 ) 2 4 = 5 , 026.55 mm 2 A = \frac{\pi d^2}{4} = \frac{\pi (80)^2}{4} = 5,026.55\text{ mm}^2 A = 4 π d 2 = 4 π ( 80 ) 2 = 5 , 026.55 mm 2 I = π d 4 64 = π ( 80 ) 4 64 = 2.0106 × 10 6 mm 4 I = \frac{\pi d^4}{64} = \frac{\pi (80)^4}{64} = 2.0106 \times 10^6\text{ mm}^4 I = 64 π d 4 = 64 π ( 80 ) 4 = 2.0106 × 1 0 6 mm 4 J = 2 I = 4.0212 × 10 6 mm 4 J = 2 I = 4.0212 \times 10^6\text{ mm}^4 J = 2 I = 4.0212 × 1 0 6 mm 4 c = r = 40 mm c = r = 40\text{ mm} c = r = 40 mm
Stresses at Top Surface Point:
Axial Tensile Stress: σ axial = P A = 150 × 10 3 N 5 , 026.55 mm 2 = 29.84 MPa \sigma_{\text{axial}} = \frac{P}{A} = \frac{150 \times 10^3\text{ N}}{5,026.55\text{ mm}^2} = 29.84\text{ MPa} σ axial = A P = 5 , 026.55 mm 2 150 × 1 0 3 N = 29.84 MPa
Bending Tensile Stress (top fiber under positive moment): σ bend = M c I = ( 3.20 × 10 6 N ⋅ mm ) ( 40 mm ) 2.0106 × 10 6 mm 4 = 63.66 MPa \sigma_{\text{bend}} = \frac{M c}{I} = \frac{(3.20 \times 10^6\text{ N}\cdot\text{mm})(40\text{ mm})}{2.0106 \times 10^6\text{ mm}^4} = 63.66\text{ MPa} σ bend = I M c = 2.0106 × 1 0 6 mm 4 ( 3.20 × 1 0 6 N ⋅ mm ) ( 40 mm ) = 63.66 MPa
Total Normal Stress ( σ x \sigma_x σ x ): σ x = σ axial + σ bend = 29.84 + 63.66 = 93.50 MPa \sigma_x = \sigma_{\text{axial}} + \sigma_{\text{bend}} = 29.84 + 63.66 = \boxed{93.50\text{ MPa}} σ x = σ axial + σ bend = 29.84 + 63.66 = 93.50 MPa
Transverse Normal Stress ( σ y \sigma_y σ y ): No transverse normal pressure acts: σ y = 0 \sigma_y = 0 σ y = 0 .
Torsional Shear Stress ( τ x y \tau_{xy} τ x y ): τ x y = T c J = ( 4.00 × 10 6 N ⋅ mm ) ( 40 mm ) 4.0212 × 10 6 mm 4 = 39.79 MPa \tau_{xy} = \frac{T c}{J} = \frac{(4.00 \times 10^6\text{ N}\cdot\text{mm})(40\text{ mm})}{4.0212 \times 10^6\text{ mm}^4} = \boxed{39.79\text{ MPa}} τ x y = J T c = 4.0212 × 1 0 6 mm 4 ( 4.00 × 1 0 6 N ⋅ mm ) ( 40 mm ) = 39.79 MPa
Principal Stresses and Principal Planes: σ avg = σ x + σ y 2 = 93.50 + 0 2 = 46.75 MPa \sigma_{\text{avg}} = \frac{\sigma_x + \sigma_y}{2} = \frac{93.50 + 0}{2} = 46.75\text{ MPa} σ avg = 2 σ x + σ y = 2 93.50 + 0 = 46.75 MPa R = ( σ x − σ y 2 ) 2 + τ x y 2 = ( 46.75 ) 2 + ( 39.79 ) 2 = 2185.56 + 1583.24 = 3768.80 = 61.39 MPa R = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2} = \sqrt{(46.75)^2 + (39.79)^2} = \sqrt{2185.56 + 1583.24} = \sqrt{3768.80} = 61.39\text{ MPa} R = ( 2 σ x − σ y ) 2 + τ x y 2 = ( 46.75 ) 2 + ( 39.79 ) 2 = 2185.56 + 1583.24 = 3768.80 = 61.39 MPa σ 1 = σ avg + R = 46.75 + 61.39 = 108.14 MPa \boxed{\sigma_1 = \sigma_{\text{avg}} + R = 46.75 + 61.39 = 108.14\text{ MPa}} σ 1 = σ avg + R = 46.75 + 61.39 = 108.14 MPa σ 2 = σ avg − R = 46.75 − 61.39 = − 14.64 MPa \boxed{\sigma_2 = \sigma_{\text{avg}} - R = 46.75 - 61.39 = -14.64\text{ MPa}} σ 2 = σ avg − R = 46.75 − 61.39 = − 14.64 MPa
Principal Plane Angle: tan 2 θ p = 2 τ x y σ x − σ y = 2 ( 39.79 ) 93.50 = 79.58 93.50 = 0.8511 \tan 2\theta_p = \frac{2 \tau_{xy}}{\sigma_x - \sigma_y} = \frac{2 (39.79)}{93.50} = \frac{79.58}{93.50} = 0.8511 tan 2 θ p = σ x − σ y 2 τ x y = 93.50 2 ( 39.79 ) = 93.50 79.58 = 0.8511 2 θ p = 40.40 ∘ ⟹ θ p = 20.20 ∘ 2\theta_p = 40.40^\circ \implies \boxed{\theta_p = 20.20^\circ} 2 θ p = 40.4 0 ∘ ⟹ θ p = 20.2 0 ∘
Maximum Shear Stresses:
Maximum In-Plane Shear Stress: τ max , in-plane = R = 61.39 MPa \tau_{\max, \text{in-plane}} = R = \boxed{61.39\text{ MPa}} τ m a x , in-plane = R = 61.39 MPa
Absolute Maximum Shear Stress:
Since σ 1 = + 108.14 MPa \sigma_1 = +108.14\text{ MPa} σ 1 = + 108.14 MPa is tensile and σ 2 = − 14.64 MPa \sigma_2 = -14.64\text{ MPa} σ 2 = − 14.64 MPa is compressive (opposite signs), the 3D principal stress σ 3 = 0 \sigma_3 = 0 σ 3 = 0 lies between σ 1 \sigma_1 σ 1 and σ 2 \sigma_2 σ 2 : τ max , abs = σ 1 − σ 2 2 = 108.14 − ( − 14.64 ) 2 = 61.39 MPa \boxed{\tau_{\max, \text{abs}} = \frac{\sigma_1 - \sigma_2}{2} = \frac{108.14 - (-14.64)}{2} = 61.39\text{ MPa}} τ m a x , abs = 2 σ 1 − σ 2 = 2 108.14 − ( − 14.64 ) = 61.39 MPa
von Mises Failure Criterion Check: σ v = σ 1 2 − σ 1 σ 2 + σ 2 2 = ( 108.14 ) 2 − ( 108.14 ) ( − 14.64 ) + ( − 14.64 ) 2 \sigma_v = \sqrt{\sigma_1^2 - \sigma_1 \sigma_2 + \sigma_2^2} = \sqrt{(108.14)^2 - (108.14)(-14.64) + (-14.64)^2} σ v = σ 1 2 − σ 1 σ 2 + σ 2 2 = ( 108.14 ) 2 − ( 108.14 ) ( − 14.64 ) + ( − 14.64 ) 2 σ v = 11 , 694.3 + 1 , 583.2 + 214.3 = 13 , 491.8 = 116.15 MPa \sigma_v = \sqrt{11,694.3 + 1,583.2 + 214.3} = \sqrt{13,491.8} = 116.15\text{ MPa} σ v = 11 , 694.3 + 1 , 583.2 + 214.3 = 13 , 491.8 = 116.15 MPa Factor of Safety F S = σ y σ v = 300 MPa 116.15 MPa = 2.58 \text{Factor of Safety } FS = \frac{\sigma_y}{\sigma_v} = \frac{300\text{ MPa}}{116.15\text{ MPa}} = \boxed{2.58} Factor of Safety FS = σ v σ y = 116.15 MPa 300 MPa = 2.58 The shaft is fully safe against ductile yielding.
11. CELE Board Exam Traps & Common Computational Errors
Warning
Trap 1: Second Moment-Area Theorem Reference Point Inversion: In evaluating tangential deviation t B / A t_{B/A} t B / A , always take the moment of the M / ( E I ) M/(EI) M / ( E I ) area about the point being deflected ( B B B ) , not about the tangent origin ( A A A ). Calculating x ˉ \bar{x} x ˉ from A A A yields t A / B t_{A/B} t A / B , which is completely different from t B / A t_{B/A} t B / A .
Warning
Trap 2: Absolute Maximum Shear Stress with Like Principal Signs: When both in-plane principal stresses are tensile (e.g., σ 1 = 120 MPa , σ 2 = 20 MPa \sigma_1 = 120\text{ MPa}, \sigma_2 = 20\text{ MPa} σ 1 = 120 MPa , σ 2 = 20 MPa ), candidates routinely calculate τ max = ( 120 − 20 ) / 2 = 50 MPa \tau_{\max} = (120 - 20)/2 = 50\text{ MPa} τ m a x = ( 120 − 20 ) /2 = 50 MPa . However, because σ 3 = 0 \sigma_3 = 0 σ 3 = 0 , the true out-of-plane absolute maximum shear stress is τ max , abs = ( 120 − 0 ) / 2 = 60 MPa \tau_{\max, \text{abs}} = (120 - 0)/2 = 60\text{ MPa} τ m a x , abs = ( 120 − 0 ) /2 = 60 MPa . Overlooking σ 3 = 0 \sigma_3 = 0 σ 3 = 0 is a lethal board exam pitfall.
Warning
Trap 3: Middle-Third Rule Scope: The Middle-Third Rule ( e ≤ h / 6 e \le h/6 e ≤ h /6 ) applies strictly to rectangular cross-sections . Applying e ≤ h / 6 e \le h/6 e ≤ h /6 to a circular foundation pier instead of the Middle-Quarter Rule ( e ≤ d / 8 e \le d/8 e ≤ d /8 ) will incorrectly allow tension over a significant portion of the perimeter.