Study guide
12.3 Beam Stresses: Flexural and Transverse Shear
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
12.3 Beam Stresses: Flexural and Transverse Shear
Key Takeaways Explain This Topic AI
Differential equilibrium calculus links beam loading, shear, and bending moment: d V d x = − w ( x ) \frac{dV}{dx} = -w(x) d x d V = − w ( x ) and d M d x = V ( x ) \frac{dM}{dx} = V(x) d x d M = V ( x ) ; maximum bending moment occurs where shear crosses zero ( V = 0 V = 0 V = 0 ) or at concentrated load points.
The flexure formula σ b = − M y I \sigma_b = -\frac{M y}{I} σ b = − I M y governs normal bending stresses under Euler-Bernoulli beam theory, yielding peak surface stresses σ max = M c I = M S \sigma_{\max} = \frac{M c}{I} = \frac{M}{S} σ m a x = I M c = S M , where section modulus S = b h 2 6 S = \frac{b h^2}{6} S = 6 b h 2 for rectangular sections and S = π d 3 32 S = \frac{\pi d^3}{32} S = 32 π d 3 for solid circular sections.
Jourawski's formula τ = V Q I b \tau = \frac{V Q}{I b} τ = I b V Q dictates horizontal and transverse shear stress in beams; first moment of area Q = A ′ y ˉ ′ Q = A' \bar{y}' Q = A ′ y ˉ ′ peaks at the neutral axis and vanishes at extreme exterior fibers.
Shear stress distributions depend on geometry: rectangular cross-sections exhibit a parabolic distribution with τ max = 1.5 V A \tau_{\max} = 1.5 \frac{V}{A} τ m a x = 1.5 A V ; solid circular sections peak at τ max = 4 3 V A \tau_{\max} = \frac{4}{3}\frac{V}{A} τ m a x = 3 4 A V ; and wide-flange / I-beams carry 90% to 98% of total shear in the web with τ max ≈ V d ⋅ t w \tau_{\max} \approx \frac{V}{d \cdot t_w} τ m a x ≈ d ⋅ t w V .
Shear flow q = V Q I q = \frac{V Q}{I} q = I V Q governs the required pitch spacing of bolts, nails, or intermittent welds joining built-up beam elements via s = R v q = R v I V Q s = \frac{R_v}{q} = \frac{R_v I}{V Q} s = q R v = V Q R v I .
Last updated: October 2026
12.3 Beam Stresses: Flexural and Transverse Shear
Flexural members (beams and girders) represent fundamental load-carrying elements in buildings, bridges, and offshore platforms. Designing a beam requires analyzing two concurrent internal stress distributions: longitudinal normal stresses generated by bending moments ( σ b \sigma_b σ b ), and transverse/horizontal shearing stresses generated by vertical shear forces ( τ \tau τ ).
1. Internal Forces and Differential Equilibrium in Beams
Consider an infinitesimal beam segment of length d x dx d x subjected to a downward distributed load w ( x ) w(x) w ( x ) , shear force V V V , and bending moment M M M :
Differential Equilibrium Relationships
Vertical Force Equilibrium ( ∑ F y = 0 \sum F_y = 0 ∑ F y = 0 ): V − ( V + d V ) − w ( x ) d x = 0 ⟹ d V d x = − w ( x ) V - (V + dV) - w(x) \, dx = 0 \implies \boxed{\frac{dV}{dx} = -w(x)} V − ( V + d V ) − w ( x ) d x = 0 ⟹ d x d V = − w ( x ) Δ V = V 2 − V 1 = − ∫ x 1 x 2 w ( x ) d x = − ( Area under distributed load curve ) \Delta V = V_2 - V_1 = - \int_{x_1}^{x_2} w(x) \, dx = - (\text{Area under distributed load curve}) Δ V = V 2 − V 1 = − ∫ x 1 x 2 w ( x ) d x = − ( Area under distributed load curve )
Moment Equilibrium ( ∑ M O = 0 \sum M_O = 0 ∑ M O = 0 ): − M + ( M + d M ) − V d x − w ( x ) ( d x ) 2 2 = 0 ⟹ d M d x = V ( x ) -M + (M + dM) - V \, dx - w(x) \frac{(dx)^2}{2} = 0 \implies \boxed{\frac{dM}{dx} = V(x)} − M + ( M + d M ) − V d x − w ( x ) 2 ( d x ) 2 = 0 ⟹ d x d M = V ( x ) Δ M = M 2 − M 1 = ∫ x 1 x 2 V ( x ) d x = ( Area under shear diagram ) \Delta M = M_2 - M_1 = \int_{x_1}^{x_2} V(x) \, dx = (\text{Area under shear diagram}) Δ M = M 2 − M 1 = ∫ x 1 x 2 V ( x ) d x = ( Area under shear diagram )
Critical Curve Properties for Shear and Moment Diagrams
Slope of Shear Diagram: Equals the negative intensity of the distributed load ( Slope = − w \text{Slope } = -w Slope = − w ).
Slope of Moment Diagram: Equals the local vertical shear force ( Slope = V \text{Slope } = V Slope = V ).
Peak Bending Moments: Occur where the shear diagram crosses zero ( V = 0 V = 0 V = 0 ) or passes through a sharp discontinuity.
Point of Inflection: A point along the beam where M ( x ) = 0 M(x) = 0 M ( x ) = 0 , indicating a reversal in curvature (from sagging/positive to hogging/negative bending).
- 2. Pure Bending and the Flexure Formula (Navier's Hypothesis)
- Euler-Bernoulli Assumptions
Navier's Hypothesis: Cross-sections originally plane and perpendicular to the longitudinal axis remain plane and perpendicular to the neutral axis after bending (shear deformations are neglected).
Material Linearity: The beam is homogeneous, isotropic, and obeys Hooke's Law ( σ = E ϵ \sigma = E \epsilon σ = E ϵ ).
Prismatic Beam: The cross-section is uniform along the length with a vertical longitudinal plane of symmetry containing the loads.
Longitudinal Strain and the Neutral Axis
Due to beam curvature κ = 1 / ρ \kappa = 1/\rho κ = 1/ ρ , longitudinal strain ϵ x \epsilon_x ϵ x varies linearly with vertical distance y y y from the neutral surface : ϵ x = − y ρ = − κ y \epsilon_x = - \frac{y}{\rho} = - \kappa y ϵ x = − ρ y = − κ y At the neutral axis ( y = 0 y = 0 y = 0 ), longitudinal strain and normal stress are identically zero. Equilibrium of axial forces ( ∫ A σ x d A = 0 \int_A \sigma_x \, dA = 0 ∫ A σ x d A = 0 ) proves that the neutral axis must pass directly through the centroid of the cross-section .
The Flexure Formula
Equating internal resisting moment to applied bending moment M M M : M = − ∫ A y σ x d A = E ρ ∫ A y 2 d A = E I ρ M = - \int_A y \sigma_x \, dA = \frac{E}{\rho} \int_A y^2 \, dA = \frac{E I}{\rho} M = − ∫ A y σ x d A = ρ E ∫ A y 2 d A = ρ E I σ b = − M y I \boxed{\sigma_b = - \frac{M y}{I}} σ b = − I M y σ max = M c I = M S \boxed{\sigma_{\max} = \frac{M c}{I} = \frac{M}{S}} σ m a x = I M c = S M where:
M M M is internal bending moment.
y y y is vertical coordinate measured from the neutral axis (positive upward).
c c c is distance from neutral axis to the outermost fiber ( c = y max c = y_{\max} c = y m a x ).
I I I is centroidal second moment of area (moment of inertia) about the bending axis: I = ∫ A y 2 d A I = \int_A y^2 \, dA I = ∫ A y 2 d A .
S = I c S = \frac{I}{c} S = c I is the elastic section modulus ( mm 3 \text{mm}^3 mm 3 or m 3 \text{m}^3 m 3 ).
3. Section Modulus and Cross-Sectional Geometry
Cross-Section Shape Dimensions Centroidal Moment of Inertia ( I I I ) Section Modulus ( S = I / c S = I/c S = I / c )
Solid Rectangle Width b b b , Depth h h h I x = b h 3 12 I_x = \frac{b h^3}{12} I x = 12 b h 3 S x = b h 2 6 S_x = \frac{b h^2}{6} S x = 6 b h 2
Solid Circle Diameter d d d I = π d 4 64 I = \frac{\pi d^4}{64} I = 64 π d 4 S = π d 3 32 S = \frac{\pi d^3}{32} S = 32 π d 3
Hollow Pipe / Tube Outer D D D , Inner d d d I = π ( D 4 − d 4 ) 64 I = \frac{\pi(D^4 - d^4)}{64} I = 64 π ( D 4 − d 4 ) S = π ( D 4 − d 4 ) 32 D S = \frac{\pi(D^4 - d^4)}{32 D} S = 32 D π ( D 4 − d 4 )
Structural I-Beam Flanges b f × t f b_f \times t_f b f × t f , Web h w × t w h_w \times t_w h w × t w I x = b f d 3 12 − ( b f − t w ) h w 3 12 I_x = \frac{b_f d^3}{12} - \frac{(b_f - t_w) h_w^3}{12} I x = 12 b f d 3 − 12 ( b f − t w ) h w 3 S x = I x d / 2 S_x = \frac{I_x}{d/2} S x = d /2 I x
4. Unsymmetrical (Biaxial) Bending About Principal Axes
When applied bending moments act in a plane inclined relative to the principal centroidal axes ( y , z ) (y, z) ( y , z ) of the cross-section: σ ( y , z ) = − M z y I z + M y z I y \sigma(y, z) = - \frac{M_z y}{I_z} + \frac{M_y z}{I_y} σ ( y , z ) = − I z M z y + I y M y z where M z M_z M z and M y M_y M y are moment vector components along the principal axes. The orientation of the neutral axis (line of zero stress, σ = 0 \sigma = 0 σ = 0 ) forms an angle α \alpha α with the z z z -axis: tan α = ( I z I y ) tan θ \tan \alpha = \left(\frac{I_z}{I_y}\right) \tan \theta tan α = ( I y I z ) tan θ where θ \theta θ is the inclination angle of the applied moment vector relative to the z z z -axis. Unless I y = I z I_y = I_z I y = I z (such as for square or circular sections), the neutral axis is NOT perpendicular to the applied moment plane .
5. Horizontal and Transverse Shear Stress (Jourawski's Formula)
In a beam subjected to transverse loading, the variation in bending moment along x x x produces differing normal compressive and tensile forces on vertical sections. To maintain equilibrium of an elemental slice, horizontal shearing stresses must develop along longitudinal planes. By the complementary property of shear, horizontal shear stress τ x y \tau_{xy} τ x y is identically equal to vertical transverse shear stress τ y x \tau_{yx} τ y x .
Jourawski's Shear Formula
τ = V Q I b \boxed{\tau = \frac{V Q}{I b}} τ = I b V Q where:
V V V is vertical shear force at the cross-section.
I I I is moment of inertia of the entire cross-section about the neutral axis.
b b b is width of the cross-section at the specific horizontal plane where shear stress is evaluated.
Q Q Q is the first moment of area of that portion of the cross-section located beyond the cut plane (above or below), taken about the centroidal neutral axis: Q = ∫ y 1 c y d A = A ′ y ˉ ′ \boxed{Q = \int_{y_1}^c y \, dA = A' \bar{y}'} Q = ∫ y 1 c y d A = A ′ y ˉ ′ where A ′ A' A ′ is the partial area above level y 1 y_1 y 1 , and y ˉ ′ \bar{y}' y ˉ ′ is the vertical distance from the neutral axis to the centroid of A ′ A' A ′ .
6. Shear Stress Distributions: Rectangular, Circular, and Flanged Profiles
Loading diagram...
1. Rectangular Cross-Section ( b × h b \times h b × h )
At distance y y y from the neutral axis, the area above y y y is A ′ = b ( h / 2 − y ) A' = b (h/2 - y) A ′ = b ( h /2 − y ) with centroid at y ˉ ′ = y + 1 2 ( h / 2 − y ) = 1 2 ( h / 2 + y ) \bar{y}' = y + \frac{1}{2}(h/2 - y) = \frac{1}{2}(h/2 + y) y ˉ ′ = y + 2 1 ( h /2 − y ) = 2 1 ( h /2 + y ) . Thus: Q ( y ) = A ′ y ˉ ′ = b 2 ( h 2 4 − y 2 ) Q(y) = A' \bar{y}' = \frac{b}{2} \left(\frac{h^2}{4} - y^2\right) Q ( y ) = A ′ y ˉ ′ = 2 b ( 4 h 2 − y 2 ) Substituting into τ = V Q I b \tau = \frac{V Q}{I b} τ = I b V Q with I = b h 3 12 I = \frac{b h^3}{12} I = 12 b h 3 : τ ( y ) = V [ b 2 ( h 2 / 4 − y 2 ) ] ( b h 3 12 ) b = 6 V b h 3 ( h 2 4 − y 2 ) = 3 V 2 A [ 1 − ( 2 y h ) 2 ] \tau(y) = \frac{V [\frac{b}{2}(h^2/4 - y^2)]}{(\frac{b h^3}{12}) b} = \frac{6 V}{b h^3} \left(\frac{h^2}{4} - y^2\right) = \frac{3 V}{2 A} \left[1 - \left(\frac{2y}{h}\right)^2\right] τ ( y ) = ( 12 b h 3 ) b V [ 2 b ( h 2 /4 − y 2 )] = b h 3 6 V ( 4 h 2 − y 2 ) = 2 A 3 V [ 1 − ( h 2 y ) 2 ]
Parabolic distribution with τ = 0 \tau = 0 τ = 0 at top and bottom surfaces ( y = ± h / 2 y = \pm h/2 y = ± h /2 ).
Maximum shear stress occurs at the neutral axis ( y = 0 y = 0 y = 0 ) : τ max = 3 V 2 A = 1.50 V A \boxed{\tau_{\max} = \frac{3 V}{2 A} = 1.50 \frac{V}{A}} τ m a x = 2 A 3 V = 1.50 A V
2. Solid Circular Cross-Section ( d d d )
Integration across a circular boundary yields a parabolic variation peaking at the neutral axis: τ max = 4 V 3 A = 1.333 V π R 2 \boxed{\tau_{\max} = \frac{4 V}{3 A} = 1.333 \frac{V}{\pi R^2}} τ m a x = 3 A 4 V = 1.333 π R 2 V
3. Structural Wide-Flange / I-Beams
Flanges: Because flange width b f b_f b f is large, horizontal shear stress τ = V Q I b f \tau = \frac{V Q}{I b_f} τ = I b f V Q is very small.
Web: At the flange-web junction, width drops abruptly from b f b_f b f to t w t_w t w , causing a sudden discontinuity jump in shear stress.
Web Shear Contribution: The web carries 90 % to 98 % 90\%\text{ to }98\% 90% to 98% of the total vertical shear force. In structural steel practice, average web shear stress is commonly approximated as: τ web, avg ≈ V A web = V d ⋅ t w \tau_{\text{web, avg}} \approx \frac{V}{A_{\text{web}}} = \frac{V}{d \cdot t_w} τ web, avg ≈ A web V = d ⋅ t w V
7. Shear Flow and Built-Up Beam Fastener Spacing
When a beam is fabricated by fastening multiple plates or planks together (e.g., wooden box beams, built-up steel girders with cover plates), the fasteners must resist the longitudinal shear force attempting to slide the layers past one another.
Shear Flow ( q q q )
Shear flow is the shear force per unit length along the longitudinal axis of the beam: q = τ b = V Q I ( N/mm or kN/m ) \boxed{q = \tau b = \frac{V Q}{I}} \quad (\text{N/mm or kN/m}) q = τ b = I V Q ( N/mm or kN/m )
Fastener Pitch Spacing ( s s s )
Let R v R_v R v be the total shear capacity of all fasteners positioned at a single longitudinal cross-section (for m m m bolts or shear planes per station, R v = m R bolt R_v = m R_{\text{bolt}} R v = m R bolt ). Over a longitudinal pitch spacing s s s , the total resisting capacity is R v = q ⋅ s R_v = q \cdot s R v = q ⋅ s : s = R v q = R v I V Q \boxed{s = \frac{R_v}{q} = \frac{R_v I}{V Q}} s = q R v = V Q R v I
Important
When computing Q Q Q for fastener design, Q Q Q is calculated strictly for the detached component that would slide if the fasteners failed, NOT for the entire cross-section.
8. Worked Example: Built-Up T-Beam Flexural Capacity and Nail Pitch
Problem Statement: A built-up timber T-beam is constructed by nailing a horizontal flange plank ( 200 mm 200\text{ mm} 200 mm wide × 50 mm \times 50\text{ mm} × 50 mm thick) to a vertical stem plank ( 50 mm 50\text{ mm} 50 mm wide × 200 mm \times 200\text{ mm} × 200 mm deep). The beam supports a simply supported span of L = 4.0 m L = 4.0\text{ m} L = 4.0 m carrying a concentrated load P = 18 kN P = 18\text{ kN} P = 18 kN at midspan.
Locate the centroid and determine the moment of inertia about the neutral axis ( I NA I_{\text{NA}} I NA ).
Calculate the maximum flexural tensile and compressive stresses.
If the flange and stem are joined by nails having an allowable lateral shear capacity of R nail = 800 N R_{\text{nail}} = 800\text{ N} R nail = 800 N , determine the maximum longitudinal nail spacing s s s .
Step-by-Step Solution:
Centroid Location (measured from bottom of stem):
Flange ( 1 1 1 ): A 1 = 200 × 50 = 10 , 000 mm 2 A_1 = 200 \times 50 = 10,000\text{ mm}^2 A 1 = 200 × 50 = 10 , 000 mm 2 , y 1 = 200 + 25 = 225 mm y_1 = 200 + 25 = 225\text{ mm} y 1 = 200 + 25 = 225 mm .
Stem ( 2 2 2 ): A 2 = 50 × 200 = 10 , 000 mm 2 A_2 = 50 \times 200 = 10,000\text{ mm}^2 A 2 = 50 × 200 = 10 , 000 mm 2 , y 2 = 100 mm y_2 = 100\text{ mm} y 2 = 100 mm .
Total Area: A = A 1 + A 2 = 20 , 000 mm 2 A = A_1 + A_2 = 20,000\text{ mm}^2 A = A 1 + A 2 = 20 , 000 mm 2 . y ˉ = A 1 y 1 + A 2 y 2 A = ( 10 , 000 ) ( 225 ) + ( 10 , 000 ) ( 100 ) 20 , 000 = 2 , 250 , 000 + 1 , 000 , 000 20 , 000 = 162.5 mm \bar{y} = \frac{A_1 y_1 + A_2 y_2}{A} = \frac{(10,000)(225) + (10,000)(100)}{20,000} = \frac{2,250,000 + 1,000,000}{20,000} = 162.5\text{ mm} y ˉ = A A 1 y 1 + A 2 y 2 = 20 , 000 ( 10 , 000 ) ( 225 ) + ( 10 , 000 ) ( 100 ) = 20 , 000 2 , 250 , 000 + 1 , 000 , 000 = 162.5 mm
Distance to top fiber: c top = ( 200 + 50 ) − 162.5 = 87.5 mm c_{\text{top}} = (200 + 50) - 162.5 = 87.5\text{ mm} c top = ( 200 + 50 ) − 162.5 = 87.5 mm .
Distance to bottom fiber: c bottom = 162.5 mm c_{\text{bottom}} = 162.5\text{ mm} c bottom = 162.5 mm .
Moment of Inertia via Parallel Axis Theorem ( I NA I_{\text{NA}} I NA ):
Flange: I 1 = b 1 h 1 3 12 + A 1 d 1 2 = 200 ( 50 ) 3 12 + 10 , 000 ( 225 − 162.5 ) 2 = 2.083 × 10 6 + 10 , 000 ( 62.5 ) 2 I_1 = \frac{b_1 h_1^3}{12} + A_1 d_1^2 = \frac{200 (50)^3}{12} + 10,000 (225 - 162.5)^2 = 2.083 \times 10^6 + 10,000 (62.5)^2 I 1 = 12 b 1 h 1 3 + A 1 d 1 2 = 12 200 ( 50 ) 3 + 10 , 000 ( 225 − 162.5 ) 2 = 2.083 × 1 0 6 + 10 , 000 ( 62.5 ) 2 I 1 = 2.083 × 10 6 + 39.063 × 10 6 = 41.146 × 10 6 mm 4 I_1 = 2.083 \times 10^6 + 39.063 \times 10^6 = 41.146 \times 10^6\text{ mm}^4 I 1 = 2.083 × 1 0 6 + 39.063 × 1 0 6 = 41.146 × 1 0 6 mm 4
Stem: I 2 = b 2 h 2 3 12 + A 2 d 2 2 = 50 ( 200 ) 3 12 + 10 , 000 ( 162.5 − 100 ) 2 = 33.333 × 10 6 + 10 , 000 ( 62.5 ) 2 I_2 = \frac{b_2 h_2^3}{12} + A_2 d_2^2 = \frac{50 (200)^3}{12} + 10,000 (162.5 - 100)^2 = 33.333 \times 10^6 + 10,000 (62.5)^2 I 2 = 12 b 2 h 2 3 + A 2 d 2 2 = 12 50 ( 200 ) 3 + 10 , 000 ( 162.5 − 100 ) 2 = 33.333 × 1 0 6 + 10 , 000 ( 62.5 ) 2 I 2 = 33.333 × 10 6 + 39.063 × 10 6 = 72.396 × 10 6 mm 4 I_2 = 33.333 \times 10^6 + 39.063 \times 10^6 = 72.396 \times 10^6\text{ mm}^4 I 2 = 33.333 × 1 0 6 + 39.063 × 1 0 6 = 72.396 × 1 0 6 mm 4
Total Moment of Inertia: I NA = I 1 + I 2 = 113.542 × 10 6 mm 4 \boxed{I_{\text{NA}} = I_1 + I_2 = 113.542 \times 10^6\text{ mm}^4} I NA = I 1 + I 2 = 113.542 × 1 0 6 mm 4
Maximum Bending Moment and Maximum Stresses:
Simply supported beam with center load P = 18 kN P = 18\text{ kN} P = 18 kN on span L = 4.0 m L = 4.0\text{ m} L = 4.0 m : V max = P 2 = 9.0 kN = 9 , 000 N V_{\max} = \frac{P}{2} = 9.0\text{ kN} = 9,000\text{ N} V m a x = 2 P = 9.0 kN = 9 , 000 N M max = P L 4 = ( 18 kN ) ( 4.0 m ) 4 = 18.0 kN ⋅ m = 18.0 × 10 6 N ⋅ mm M_{\max} = \frac{P L}{4} = \frac{(18\text{ kN})(4.0\text{ m})}{4} = 18.0\text{ kN}\cdot\text{m} = 18.0 \times 10^6\text{ N}\cdot\text{mm} M m a x = 4 P L = 4 ( 18 kN ) ( 4.0 m ) = 18.0 kN ⋅ m = 18.0 × 1 0 6 N ⋅ mm
Maximum compressive stress (at top fiber, y = + c top = + 87.5 mm y = +c_{\text{top}} = +87.5\text{ mm} y = + c top = + 87.5 mm ): σ comp = M c top I = ( 18.0 × 10 6 ) ( 87.5 ) 113.542 × 10 6 = 13.87 MPa \sigma_{\text{comp}} = \frac{M c_{\text{top}}}{I} = \frac{(18.0 \times 10^6)(87.5)}{113.542 \times 10^6} = \boxed{13.87\text{ MPa}} σ comp = I M c top = 113.542 × 1 0 6 ( 18.0 × 1 0 6 ) ( 87.5 ) = 13.87 MPa
Maximum tensile stress (at bottom fiber, y = − c bottom = − 162.5 mm y = -c_{\text{bottom}} = -162.5\text{ mm} y = − c bottom = − 162.5 mm ): σ tens = M c bottom I = ( 18.0 × 10 6 ) ( 162.5 ) 113.542 × 10 6 = 25.76 MPa \sigma_{\text{tens}} = \frac{M c_{\text{bottom}}}{I} = \frac{(18.0 \times 10^6)(162.5)}{113.542 \times 10^6} = \boxed{25.76\text{ MPa}} σ tens = I M c bottom = 113.542 × 1 0 6 ( 18.0 × 1 0 6 ) ( 162.5 ) = 25.76 MPa
Nail Spacing ( s s s ):
To prevent the flange from sliding off the stem, evaluate Q Q Q of the flange alone: Q flange = A 1 d 1 = ( 10 , 000 mm 2 ) ( 62.5 mm ) = 625 , 000 mm 3 Q_{\text{flange}} = A_1 d_1 = (10,000\text{ mm}^2)(62.5\text{ mm}) = 625,000\text{ mm}^3 Q flange = A 1 d 1 = ( 10 , 000 mm 2 ) ( 62.5 mm ) = 625 , 000 mm 3
Shear flow at the flange-stem interface under maximum shear V = 9 , 000 N V = 9,000\text{ N} V = 9 , 000 N : q = V Q I = ( 9 , 000 N ) ( 625 , 000 mm 3 ) 113.542 × 10 6 mm 4 = 5.625 × 10 9 113.542 × 10 6 = 49.54 N/mm q = \frac{V Q}{I} = \frac{(9,000\text{ N})(625,000\text{ mm}^3)}{113.542 \times 10^6\text{ mm}^4} = \frac{5.625 \times 10^9}{113.542 \times 10^6} = 49.54\text{ N/mm} q = I V Q = 113.542 × 1 0 6 mm 4 ( 9 , 000 N ) ( 625 , 000 mm 3 ) = 113.542 × 1 0 6 5.625 × 1 0 9 = 49.54 N/mm
Required nail pitch spacing (single line of nails, R v = 800 N R_v = 800\text{ N} R v = 800 N ): s = R nail q = 800 N 49.54 N/mm = 16.15 mm ≈ 16 mm \boxed{s = \frac{R_{\text{nail}}}{q} = \frac{800\text{ N}}{49.54\text{ N/mm}} = 16.15\text{ mm} \approx 16\text{ mm}} s = q R nail = 49.54 N/mm 800 N = 16.15 mm ≈ 16 mm
9. CELE Board Exam Traps & Common Computational Errors
Warning
Trap 1: Unsymmetrical Cross-Section Tensile vs. Compressive Stresses: For non-symmetric sections (T-beams, inverted channels), the neutral axis does not lie at mid-depth ( c top ≠ c bottom c_{\text{top}} \ne c_{\text{bottom}} c top = c bottom ). Never use a single section modulus. Always compute both extreme fiber stresses independently to identify which controls relative to allowable tensile and compressive limits.
Warning
Trap 2: First Moment of Area ( Q Q Q ) Evaluation Errors: When computing Q = A ′ y ˉ ′ Q = A' \bar{y}' Q = A ′ y ˉ ′ , y ˉ ′ \bar{y}' y ˉ ′ is the distance from the neutral axis of the composite section to the centroid of partial area A ′ A' A ′ . A common mistake is measuring y ˉ ′ \bar{y}' y ˉ ′ from the bottom of the beam or from the interface seam.
Warning
Trap 3: Fastener Pitch Multiple Shear Planes: If nails or bolts connect flanges with two lines of fasteners or double-shear clips, R v = n R fastener R_v = n R_{\text{fastener}} R v = n R fastener . Omitting the fastener multiplier n n n results in pitch spacings that are half the correct safe value.