Study guide
12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels
Key Takeaways Explain This Topic AI
The elastic torsion formula τ = T ρ J \tau = \frac{T \rho}{J} τ = J Tρ dictates that shear stress varies linearly from zero at the shaft centroid to τ max = T r J \tau_{\max} = \frac{T r}{J} τ m a x = J T r at the outer boundary, with polar moment of inertia J = π d 4 32 J = \frac{\pi d^4}{32} J = 32 π d 4 for solid circular shafts and J = π ( D 4 − d 4 ) 32 J = \frac{\pi(D^4 - d^4)}{32} J = 32 π ( D 4 − d 4 ) for hollow shafts.
Angle of twist is governed by θ = T L J G \theta = \frac{T L}{J G} θ = J G T L (expressed strictly in radians), where the shear modulus (modulus of rigidity) is G = E 2 ( 1 + ν ) G = \frac{E}{2(1 + \nu)} G = 2 ( 1 + ν ) E ; shaft power transmission follows P = ω T = 2 π f T P = \omega T = 2\pi f T P = ω T = 2 π f T , where T = 60 P 2 π N T = \frac{60 P}{2\pi N} T = 2 π N 60 P .
In rigid flanged bolt couplings with concentric bolt circles, bolt shear deformation is proportional to radial distance from the shaft center ( τ 1 / R 1 = τ 2 / R 2 \tau_1 / R_1 = \tau_2 / R_2 τ 1 / R 1 = τ 2 / R 2 ); bolts on the outer circle reach allowable stress first.
Thin-walled cylindrical pressure vessels ( t ≤ D / 20 t \le D/20 t ≤ D /20 ) develop tangential (hoop) stress σ t = p D 2 t \sigma_t = \frac{p D}{2 t} σ t = 2 t p D and longitudinal stress σ l = p D 4 t = 1 2 σ t \sigma_l = \frac{p D}{4 t} = \frac{1}{2}\sigma_t σ l = 4 t p D = 2 1 σ t ; spherical pressure vessels experience uniform membrane tension σ = p D 4 t \sigma = \frac{p D}{4 t} σ = 4 t p D .
When factoring joint efficiencies ( η \eta η ), longitudinal seams resist tangential hoop stress ( σ t = p D 2 t η long \sigma_t = \frac{p D}{2 t \eta_{\text{long}}} σ t = 2 t η long p D ), whereas circumferential (girth) seams resist longitudinal stress ( σ l = p D 4 t η circ \sigma_l = \frac{p D}{4 t \eta_{\text{circ}}} σ l = 4 t η circ p D ).
Last updated: October 2026
12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels
Torsional shear and biaxial membrane tension represent two critical stress categories encountered in civil and mechanical infrastructure—from circular structural columns subjected to eccentric wind-induced torsional moments to municipal water storage tanks, aqueducts, and pressurized penstocks.
1. Pure Torsion in Circular Shafts and Polar Moment of Inertia
When a circular cylindrical shaft is subjected to an applied torsional moment (torque T T T ), internal shearing stresses develop across every transverse plane.
Fundamental Assumptions of Circular Torsion
Axisymmetry: Plane cross-sections perpendicular to the longitudinal axis remain planar and circular after twisting (no warping occurs in circular cross-sections).
Radial Line Invariance: Radial lines remain straight and rotate through an angle θ \theta θ proportional to distance along the shaft.
Homogeneous, Linear Elastic Material: Shearing stress relates to shearing strain via Hooke's Law in shear: τ = G γ \tau = G \gamma τ = G γ .
The Torsion Formula
From strain geometry, shearing strain at distance ρ \rho ρ from the shaft center is γ = ρ d θ d x \gamma = \rho \frac{d\theta}{dx} γ = ρ d x d θ . Applying τ = G γ \tau = G \gamma τ = G γ and equating internal resisting torque to applied torque yields: τ = T ρ J \tau = \frac{T \rho}{J} τ = J Tρ τ max = T r J = T ( D / 2 ) J \boxed{\tau_{\max} = \frac{T r}{J} = \frac{T (D/2)}{J}} τ m a x = J T r = J T ( D /2 ) where:
T T T is internal torsional moment ( N ⋅ mm \text{N}\cdot\text{mm} N ⋅ mm or kN ⋅ m \text{kN}\cdot\text{m} kN ⋅ m ).
ρ \rho ρ is radial distance from the shaft center ( 0 ≤ ρ ≤ r 0 \le \rho \le r 0 ≤ ρ ≤ r ).
J J J is the polar moment of inertia of the cross-section ( mm 4 \text{mm}^4 mm 4 ).
τ max \tau_{\max} τ m a x occurs at the outermost boundary ( ρ = r = D / 2 \,\rho = r = D/2 ρ = r = D /2 ).
Polar Moment of Inertia ( J J J )
For circular geometry, polar moment of inertia about the centroidal axis equals the sum of rectangular moments of inertia: J = I x + I y = 2 I J = I_x + I_y = 2 I J = I x + I y = 2 I :
Cross-Section Polar Moment of Inertia ( J J J ) Maximum Shear Stress ( τ max \tau_{\max} τ m a x ) Torsional Section Modulus ( Z p = J / r Z_p = J/r Z p = J / r )
Solid Circular Shaft ( d d d ) J = π d 4 32 = π r 4 2 J = \frac{\pi d^4}{32} = \frac{\pi r^4}{2} J = 32 π d 4 = 2 π r 4 τ max = 16 T π d 3 \tau_{\max} = \frac{16 T}{\pi d^3} τ m a x = π d 3 16 T Z p = π d 3 16 Z_p = \frac{\pi d^3}{16} Z p = 16 π d 3
Hollow Circular Shaft ( D , d D, d D , d ) J = π ( D 4 − d 4 ) 32 J = \frac{\pi (D^4 - d^4)}{32} J = 32 π ( D 4 − d 4 ) τ max = 16 T D π ( D 4 − d 4 ) \tau_{\max} = \frac{16 T D}{\pi (D^4 - d^4)} τ m a x = π ( D 4 − d 4 ) 16 T D Z p = π ( D 4 − d 4 ) 16 D Z_p = \frac{\pi (D^4 - d^4)}{16 D} Z p = 16 D π ( D 4 − d 4 )
Tip
Weight Efficiency of Hollow Shafts: Material located near the center of a solid shaft carries near-zero shear stress ( ρ → 0 \,\rho \to 0 ρ → 0 ). Removing central core material creates a hollow shaft that achieves vastly superior torque capacity per unit weight, which is why drive shafts and tubular transmission towers utilize hollow circular geometry.
2. Angle of Twist and Shaft Rigidity
For a homogeneous prismatic circular shaft of length L L L , the total relative angle of rotation (twist) θ \theta θ between its ends is obtained by integrating along the axis: θ = ∫ 0 L T ( x ) J ( x ) G d x ⟹ θ = T L J G \theta = \int_0^L \frac{T(x)}{J(x) G} \, dx \implies \boxed{\theta = \frac{T L}{J G}} θ = ∫ 0 L J ( x ) G T ( x ) d x ⟹ θ = J G T L
Units: θ \theta θ is calculated strictly in radians . To convert radians to degrees: θ ∘ = θ rad × ( 180 ∘ π ) \theta^\circ = \theta_{\text{rad}} \times \left(\frac{180^\circ}{\pi}\right) θ ∘ = θ rad × ( π 18 0 ∘ ) .
Shear Modulus (Modulus of Rigidity, G G G ): G = E 2 ( 1 + ν ) G = \frac{E}{2(1 + \nu)} G = 2 ( 1 + ν ) E For structural steel ( E = 200 GPa , ν = 0.30 E = 200\text{ GPa}, \nu = 0.30 E = 200 GPa , ν = 0.30 ): G = 200 2 ( 1.30 ) ≈ 76.92 GPa ≈ 77 GPa = 77 , 000 MPa G = \frac{200}{2(1.30)} \approx 76.92\text{ GPa} \approx 77\text{ GPa} = 77,000\text{ MPa} G = 2 ( 1.30 ) 200 ≈ 76.92 GPa ≈ 77 GPa = 77 , 000 MPa .
Torsional Stiffness: k t = T θ = J G L k_t = \frac{T}{\theta} = \frac{J G}{L} k t = θ T = L J G (torque per unit radian twist).
Torsional Flexibility: f t = 1 k t = L J G f_t = \frac{1}{k_t} = \frac{L}{J G} f t = k t 1 = J G L .
Shafts in Series and Parallel
Series Shafts: Internal torque T T T is common throughout all segments; total twist is additive: θ total = ∑ T i L i J i G i \theta_{\text{total}} = \sum \frac{T_i L_i}{J_i G_i} θ total = ∑ J i G i T i L i .
Parallel / Composite Shafts: Two concentric materials bonded together twist through the identical angle ( θ 1 = θ 2 \theta_1 = \theta_2 θ 1 = θ 2 ), sharing the total torque: T = T 1 + T 2 = θ ( J 1 G 1 L + J 2 G 2 L ) T = T_1 + T_2 = \theta \left(\frac{J_1 G_1}{L} + \frac{J_2 G_2}{L}\right) T = T 1 + T 2 = θ ( L J 1 G 1 + L J 2 G 2 ) .
3. Power Transmission in Rotating Shafts
Rotating machinery transmits mechanical power P P P through drive shafts via rotational torque T T T : P = T ω = 2 π f T P = T \omega = 2\pi f T P = T ω = 2 π f T where:
P P P is power in Watts ( W = N ⋅ m/s \text{W} = \text{N}\cdot\text{m/s} W = N ⋅ m/s ) or kilowatts ( kW = 10 3 W \text{kW} = 10^3\text{ W} kW = 1 0 3 W ). (In Imperial units, 1 Horsepower (HP) = 550 ft ⋅ lb/s = 745.7 W 1\text{ Horsepower (HP)} = 550\text{ ft}\cdot\text{lb/s} = 745.7\text{ W} 1 Horsepower (HP) = 550 ft ⋅ lb/s = 745.7 W ) .
ω \omega ω is angular velocity in radians per second: ω = 2 π N 60 \omega = \frac{2\pi N}{60} ω = 60 2 π N , with rotational speed N N N in revolutions per minute ( rpm \text{rpm} rpm ).
f f f is rotational frequency in Hertz ( Hz = rev/s = N / 60 \text{Hz} = \text{rev/s} = N/60 Hz = rev/s = N /60 ).
Solving for Required Shaft Diameter
T = P ω = 60 P 2 π N T = \frac{P}{\omega} = \frac{60 P}{2\pi N} T = ω P = 2 π N 60 P Substituting T T T into the solid circular shaft capacity formula ( τ allow = 16 T π d 3 \tau_{\text{allow}} = \frac{16 T}{\pi d^3} τ allow = π d 3 16 T ): d = 16 T π τ allow 3 = 16 ( 60 P ) 2 π 2 N τ allow 3 d = \sqrt[3]{\frac{16 T}{\pi \tau_{\text{allow}}}} = \sqrt[3]{\frac{16 (60 P)}{2\pi^2 N \tau_{\text{allow}}}} d = 3 π τ allow 16 T = 3 2 π 2 N τ allow 16 ( 60 P )
4. Statically Indeterminate Torsional Systems
When a shaft is fixed rigidly at both ends (supports A A A and B B B ) and subjected to an intermediate applied torque T 0 T_0 T 0 at point C C C :
Equilibrium Equation: T A + T B = T 0 T_A + T_B = T_0 T A + T B = T 0
Compatibility Equation: The total relative twist between fixed boundaries must vanish: θ B / A = θ A C + θ C B = 0 ⟹ T A L A C J A C G − T B L C B J C B G = 0 \theta_{B/A} = \theta_{AC} + \theta_{CB} = 0 \implies \frac{T_A L_{AC}}{J_{AC} G} - \frac{T_B L_{CB}}{J_{CB} G} = 0 θ B / A = θ A C + θ CB = 0 ⟹ J A C G T A L A C − J CB G T B L CB = 0 For a uniform prismatic shaft ( J A C = J C B J_{AC} = J_{CB} J A C = J CB ): T A L A C = T B L C B ⟹ T A = T 0 ( L C B L ) , T B = T 0 ( L A C L ) T_A L_{AC} = T_B L_{CB} \implies \boxed{T_A = T_0 \left(\frac{L_{CB}}{L}\right), \quad T_B = T_0 \left(\frac{L_{AC}}{L}\right)} T A L A C = T B L CB ⟹ T A = T 0 ( L L CB ) , T B = T 0 ( L L A C )
5. Flanged Bolt Couplings
A flanged bolt coupling connects two collinear rotating shafts. Power or torque is transmitted across the joint through shearing forces developed in circumferential bolts positioned on concentric bolt pitch circles.
Loading diagram...
Single Pitch Circle
For n n n identical bolts of cross-sectional area A b = π d b 2 4 A_b = \frac{\pi d_b^2}{4} A b = 4 π d b 2 positioned on a pitch circle of radius R R R : T = n P b R = n ( τ b A b ) R T = n P_b R = n (\tau_b A_b) R T = n P b R = n ( τ b A b ) R
Multiple Concentric Bolt Rings
Consider a coupling with an inner circle of n 1 n_1 n 1 bolts at radius R 1 R_1 R 1 and an outer circle of n 2 n_2 n 2 bolts at radius R 2 R_2 R 2 ( R 2 > R 1 R_2 > R_1 R 2 > R 1 ).
Kinematic Compatibility: Because the flange plates are assumed rigid, shearing strain in each fastener is directly proportional to its radial distance from the center of rotation: γ = R d θ d x ⟹ γ 1 R 1 = γ 2 R 2 \gamma = R \frac{d\theta}{dx} \implies \frac{\gamma_1}{R_1} = \frac{\gamma_2}{R_2} γ = R d x d θ ⟹ R 1 γ 1 = R 2 γ 2
Constitutive Relation: Assuming all bolts are of identical material ( G 1 = G 2 G_1 = G_2 G 1 = G 2 ): τ 1 R 1 = τ 2 R 2 ⟹ τ 1 = τ 2 ( R 1 R 2 ) \frac{\tau_1}{R_1} = \frac{\tau_2}{R_2} \implies \tau_1 = \tau_2 \left(\frac{R_1}{R_2}\right) R 1 τ 1 = R 2 τ 2 ⟹ τ 1 = τ 2 ( R 2 R 1 )
Controlling Stress: Because R 2 > R 1 R_2 > R_1 R 2 > R 1 , the outer bolts experience higher strain and reach the allowable shearing stress first ( τ 2 = τ allow \tau_2 = \tau_{\text{allow}} τ 2 = τ allow ). The inner bolts operate at a reduced stress τ 1 = τ allow ( R 1 / R 2 ) \tau_1 = \tau_{\text{allow}} (R_1 / R_2) τ 1 = τ allow ( R 1 / R 2 ) .
Bolt Forces: If all bolts share the same diameter ( A 1 = A 2 = A b A_1 = A_2 = A_b A 1 = A 2 = A b ): P 2 = τ allow A b , P 1 = P 2 ( R 1 R 2 ) P_2 = \tau_{\text{allow}} A_b, \quad P_1 = P_2 \left(\frac{R_1}{R_2}\right) P 2 = τ allow A b , P 1 = P 2 ( R 2 R 1 )
Total Torque Capacity: T = n 1 P 1 R 1 + n 2 P 2 R 2 = n 1 ( P 2 R 1 R 2 ) R 1 + n 2 P 2 R 2 = P 2 ( n 1 R 1 2 R 2 + n 2 R 2 ) \boxed{T = n_1 P_1 R_1 + n_2 P_2 R_2 = n_1 \left(P_2 \frac{R_1}{R_2}\right) R_1 + n_2 P_2 R_2 = P_2 \left(n_1 \frac{R_1^2}{R_2} + n_2 R_2\right)} T = n 1 P 1 R 1 + n 2 P 2 R 2 = n 1 ( P 2 R 2 R 1 ) R 1 + n 2 P 2 R 2 = P 2 ( n 1 R 2 R 1 2 + n 2 R 2 )
6. Thin-Walled Pressure Vessels
A pressure vessel is classified as thin-walled when the ratio of wall thickness t t t to internal radius r r r is small ( t / r ≤ 0.10 t/r \le 0.10 t / r ≤ 0.10 , or inner diameter to thickness ratio D / t ≥ 20 D/t \ge 20 D / t ≥ 20 ). Under this condition, radial normal stress across the thickness is negligible compared to membrane tensile stresses, and membrane stress is assumed uniform across the wall thickness.
Cylindrical Pressure Vessels
Consider a thin-walled cylinder of internal diameter D D D , radius r = D / 2 r = D/2 r = D /2 , wall thickness t t t , containing internal fluid at gauge pressure p p p .
Tangential (Hoop / Circumferential) Stress ( σ t \sigma_t σ t ): Cutting a half-cylinder of length L L L through a longitudinal plane exposes the internal fluid pressure acting upward against the projected area D L D L D L , balanced by tensile forces in two wall cross-sections ( 2 t L 2 t L 2 t L ): ∑ F y = 0 ⟹ p ( D L ) − 2 ( σ t t L ) = 0 \sum F_y = 0 \implies p (D L) - 2 (\sigma_t t L) = 0 ∑ F y = 0 ⟹ p ( D L ) − 2 ( σ t t L ) = 0 σ t = p D 2 t = p r t \boxed{\sigma_t = \frac{p D}{2 t} = \frac{p r}{t}} σ t = 2 t p D = t p r
Longitudinal (Axial) Stress ( σ l \sigma_l σ l ): Cutting through a transverse plane exposes fluid pressure acting against circular end cap area π D 2 4 \frac{\pi D^2}{4} 4 π D 2 , balanced by tensile forces across annular wall area π D t \pi D t π D t : ∑ F x = 0 ⟹ p ( π D 2 4 ) − σ l ( π D t ) = 0 \sum F_x = 0 \implies p \left(\frac{\pi D^2}{4}\right) - \sigma_l (\pi D t) = 0 ∑ F x = 0 ⟹ p ( 4 π D 2 ) − σ l ( π D t ) = 0 σ l = p D 4 t = p r 2 t = 1 2 σ t \boxed{\sigma_l = \frac{p D}{4 t} = \frac{p r}{2 t} = \frac{1}{2} \sigma_t} σ l = 4 t p D = 2 t p r = 2 1 σ t
Important
In a thin-walled cylinder, hoop stress is exactly twice longitudinal stress ( σ t = 2 σ l \sigma_t = 2 \sigma_l σ t = 2 σ l ). Therefore, under internal pressure, a cylindrical pipe or tank will always rupture along a longitudinal seam parallel to its axis, never across a girth seam.
Spherical Pressure Vessels
Due to complete spherical symmetry, any section cut through the center produces the identical equilibrium balance as the longitudinal cut in a cylinder: σ sphere = p D 4 t = p r 2 t \boxed{\sigma_{\text{sphere}} = \frac{p D}{4 t} = \frac{p r}{2 t}} σ sphere = 4 t p D = 2 t p r Spherical pressure vessels require only half the wall thickness of a cylindrical vessel of identical diameter to sustain the same internal operating pressure.
In-Plane and Absolute Maximum Shear Stress in Pressure Vessels
On the exterior surface of a cylindrical vessel, principal stresses are σ 1 = σ t = p D 2 t \sigma_1 = \sigma_t = \frac{p D}{2 t} σ 1 = σ t = 2 t p D , σ 2 = σ l = p D 4 t \sigma_2 = \sigma_l = \frac{p D}{4 t} σ 2 = σ l = 4 t p D , and σ 3 = 0 \sigma_3 = 0 σ 3 = 0 (atmospheric outer surface):
Maximum In-Plane Shear Stress: τ max , in-plane = σ 1 − σ 2 2 = σ t − σ l 2 = p D / 2 t − p D / 4 t 2 = p D 8 t \tau_{\max, \text{in-plane}} = \frac{\sigma_1 - \sigma_2}{2} = \frac{\sigma_t - \sigma_l}{2} = \frac{p D / 2t - p D / 4t}{2} = \frac{p D}{8 t} τ m a x , in-plane = 2 σ 1 − σ 2 = 2 σ t − σ l = 2 p D /2 t − p D /4 t = 8 t p D
Absolute Maximum Shear Stress (3D Mohr's Circle): τ max , abs = σ 1 − σ 3 2 = σ t − 0 2 = p D 4 t \boxed{\tau_{\max, \text{abs}} = \frac{\sigma_1 - \sigma_3}{2} = \frac{\sigma_t - 0}{2} = \frac{p D}{4 t}} τ m a x , abs = 2 σ 1 − σ 3 = 2 σ t − 0 = 4 t p D
7. Joint Efficiency Considerations ( η \eta η )
In fabricated steel tanks, boilers, and penstocks, plates are joined by welding or riveting. Fabricated joints possess a joint efficiency η ≤ 1.0 \eta \le 1.0 η ≤ 1.0 (ratio of joint strength to solid plate strength):
Seam Orientation Stress Resisted Governing Design Equation Notes
Longitudinal Seam (Parallel to cylinder axis) Tangential / Hoop Stress ( σ t \sigma_t σ t ) σ t = p D 2 t η long ≤ σ allow \sigma_t = \frac{p D}{2 t \eta_{\text{long}}} \le \sigma_{\text{allow}} σ t = 2 t η long p D ≤ σ allow Controls diameter and thickness sizing in pipes
Circumferential / Girth Seam (Perpendicular to cylinder axis) Longitudinal Stress ( σ l \sigma_l σ l ) σ l = p D 4 t η circ ≤ σ allow \sigma_l = \frac{p D}{4 t \eta_{\text{circ}}} \le \sigma_{\text{allow}} σ l = 4 t η circ p D ≤ σ allow Resists end cap blow-off forces
8. Worked Example: Concentric Flanged Bolt Coupling and Drive Shaft Sizing
Problem Statement: A solid circular transmission shaft drives a heavy centrifugal pump delivering P = 180 kW P = 180\text{ kW} P = 180 kW at N = 300 rpm N = 300\text{ rpm} N = 300 rpm .
Calculate the required shaft diameter if allowable shear stress is τ allow , s = 50 MPa \tau_{\text{allow}, s} = 50\text{ MPa} τ allow , s = 50 MPa and maximum allowable twist is 0.80 ∘ 0.80^\circ 0.8 0 ∘ per meter length ( G = 80 GPa G = 80\text{ GPa} G = 80 GPa ).
The shaft connects to the pump via a flanged bolt coupling consisting of two concentric rings of 16 mm 16\text{ mm} 16 mm diameter bolts: an inner ring of 6 bolts on a pitch diameter of 200 mm 200\text{ mm} 200 mm ( R 1 = 100 mm R_1 = 100\text{ mm} R 1 = 100 mm ) and an outer ring of 8 bolts on a pitch diameter of 320 mm 320\text{ mm} 320 mm ( R 2 = 160 mm R_2 = 160\text{ mm} R 2 = 160 mm ). If allowable bolt shear stress is τ allow , b = 65 MPa \tau_{\text{allow}, b} = 65\text{ MPa} τ allow , b = 65 MPa , determine the total torque capacity of the coupling and check whether it safely transmits the operating torque.
Step-by-Step Solution:
Calculate Transmitted Torque ( T T T ): ω = 2 π N 60 = 2 π ( 300 ) 60 = 10 π = 31.416 rad/s \omega = \frac{2\pi N}{60} = \frac{2\pi (300)}{60} = 10\pi = 31.416\text{ rad/s} ω = 60 2 π N = 60 2 π ( 300 ) = 10 π = 31.416 rad/s T = P ω = 180 × 10 3 W 31.416 rad/s = 5 , 729.58 N ⋅ m = 5.730 kN ⋅ m T = \frac{P}{\omega} = \frac{180 \times 10^3\text{ W}}{31.416\text{ rad/s}} = 5,729.58\text{ N}\cdot\text{m} = 5.730\text{ kN}\cdot\text{m} T = ω P = 31.416 rad/s 180 × 1 0 3 W = 5 , 729.58 N ⋅ m = 5.730 kN ⋅ m
Size Shaft for Shear Strength: τ max = 16 T π d 3 ≤ 50 MPa \tau_{\max} = \frac{16 T}{\pi d^3} \le 50\text{ MPa} τ m a x = π d 3 16 T ≤ 50 MPa d strength = 16 ( 5 , 729.58 × 10 3 N ⋅ mm ) π ( 50 N/mm 2 ) 3 = 91 , 673 , 280 157.08 3 = 583 , 610 3 = 83.57 mm d_{\text{strength}} = \sqrt[3]{\frac{16 (5,729.58 \times 10^3\text{ N}\cdot\text{mm})}{\pi (50\text{ N/mm}^2)}} = \sqrt[3]{\frac{91,673,280}{157.08}} = \sqrt[3]{583,610} = 83.57\text{ mm} d strength = 3 π ( 50 N/mm 2 ) 16 ( 5 , 729.58 × 1 0 3 N ⋅ mm ) = 3 157.08 91 , 673 , 280 = 3 583 , 610 = 83.57 mm
Size Shaft for Torsional Rigidity: θ allow = 0.80 ∘ = 0.80 × π 180 = 0.013963 rad per L = 1000 mm \theta_{\text{allow}} = 0.80^\circ = 0.80 \times \frac{\pi}{180} = 0.013963\text{ rad per } L = 1000\text{ mm} θ allow = 0.8 0 ∘ = 0.80 × 180 π = 0.013963 rad per L = 1000 mm θ = T L J G = T L ( π d 4 / 32 ) G ≤ θ allow \theta = \frac{T L}{J G} = \frac{T L}{(\pi d^4 / 32) G} \le \theta_{\text{allow}} θ = J G T L = ( π d 4 /32 ) G T L ≤ θ allow d rigidity = 32 T L π G θ allow 4 = 32 ( 5 , 729.58 × 10 3 ) ( 1000 ) π ( 80 , 000 ) ( 0.013963 ) 4 = 1.8335 × 10 11 3 , 509.3 4 = 52 , 246 , 000 4 = 85.03 mm d_{\text{rigidity}} = \sqrt[4]{\frac{32 T L}{\pi G \theta_{\text{allow}}}} = \sqrt[4]{\frac{32 (5,729.58 \times 10^3)(1000)}{\pi (80,000)(0.013963)}} = \sqrt[4]{\frac{1.8335 \times 10^{11}}{3,509.3}} = \sqrt[4]{52,246,000} = 85.03\text{ mm} d rigidity = 4 π G θ allow 32 T L = 4 π ( 80 , 000 ) ( 0.013963 ) 32 ( 5 , 729.58 × 1 0 3 ) ( 1000 ) = 4 3 , 509.3 1.8335 × 1 0 11 = 4 52 , 246 , 000 = 85.03 mm Controlling diameter is the larger value: d = 85.1 mm d = 85.1\text{ mm} d = 85.1 mm (governed by torsional stiffness).
Coupling Torque Capacity:
Bolt cross-sectional area: A b = π ( 16 mm ) 2 4 = 201.06 mm 2 A_b = \frac{\pi (16\text{ mm})^2}{4} = 201.06\text{ mm}^2 A b = 4 π ( 16 mm ) 2 = 201.06 mm 2 .
Outer bolts control: τ 2 = τ allow , b = 65 MPa \tau_2 = \tau_{\text{allow}, b} = 65\text{ MPa} τ 2 = τ allow , b = 65 MPa . P 2 = τ 2 A b = ( 65 N/mm 2 ) ( 201.06 mm 2 ) = 13 , 069 N = 13.069 kN P_2 = \tau_2 A_b = (65\text{ N/mm}^2)(201.06\text{ mm}^2) = 13,069\text{ N} = 13.069\text{ kN} P 2 = τ 2 A b = ( 65 N/mm 2 ) ( 201.06 mm 2 ) = 13 , 069 N = 13.069 kN
Inner bolts carry reduced stress based on radius: τ 1 = τ 2 ( R 1 R 2 ) = 65 × ( 100 mm 160 mm ) = 40.625 MPa \tau_1 = \tau_2 \left(\frac{R_1}{R_2}\right) = 65 \times \left(\frac{100\text{ mm}}{160\text{ mm}}\right) = 40.625\text{ MPa} τ 1 = τ 2 ( R 2 R 1 ) = 65 × ( 160 mm 100 mm ) = 40.625 MPa P 1 = P 2 ( R 1 R 2 ) = 13.069 × 100 160 = 8.168 kN P_1 = P_2 \left(\frac{R_1}{R_2}\right) = 13.069 \times \frac{100}{160} = 8.168\text{ kN} P 1 = P 2 ( R 2 R 1 ) = 13.069 × 160 100 = 8.168 kN
Total coupling torque capacity: T coupling = n 1 P 1 R 1 + n 2 P 2 R 2 T_{\text{coupling}} = n_1 P_1 R_1 + n_2 P_2 R_2 T coupling = n 1 P 1 R 1 + n 2 P 2 R 2 T coupling = 6 ( 8.168 kN ) ( 0.100 m ) + 8 ( 13.069 kN ) ( 0.160 m ) T_{\text{coupling}} = 6 (8.168\text{ kN})(0.100\text{ m}) + 8 (13.069\text{ kN})(0.160\text{ m}) T coupling = 6 ( 8.168 kN ) ( 0.100 m ) + 8 ( 13.069 kN ) ( 0.160 m ) T coupling = 4.901 kN ⋅ m + 16.728 kN ⋅ m = 21.63 kN ⋅ m T_{\text{coupling}} = 4.901\text{ kN}\cdot\text{m} + 16.728\text{ kN}\cdot\text{m} = \boxed{21.63\text{ kN}\cdot\text{m}} T coupling = 4.901 kN ⋅ m + 16.728 kN ⋅ m = 21.63 kN ⋅ m
Capacity Check: T coupling = 21.63 kN ⋅ m > T operating = 5.73 kN ⋅ m T_{\text{coupling}} = 21.63\text{ kN}\cdot\text{m} > T_{\text{operating}} = 5.73\text{ kN}\cdot\text{m} T coupling = 21.63 kN ⋅ m > T operating = 5.73 kN ⋅ m . The coupling provides a safety factor of 3.77 3.77 3.77 , fully safe.
9. CELE Board Exam Traps & Common Computational Errors
Warning
Trap 1: The Angle of Twist Unit Mismatch: When computing twist via θ = T L J G \theta = \frac{T L}{J G} θ = J G T L , the output is strictly in radians . If a question requests degrees, failing to multiply by 180 π \frac{180}{\pi} π 180 will understate the angular twist by a factor of 57.3.
Warning
Trap 2: Pressure Vessel Seam Inversion: The longitudinal seam of a cylindrical vessel runs parallel to the length and must resist hoop stress ( σ t = p D / 2 t \sigma_t = p D / 2 t σ t = p D /2 t ). The circumferential seam runs around the perimeter and resists longitudinal stress ( σ l = p D / 4 t \sigma_l = p D / 4 t σ l = p D /4 t ). Confusing which joint efficiency applies to which seam is the most common pressure vessel error on board exams.
Warning
Trap 3: Uniform Bolt Shear Assumption on Concentric Rings: Never assume all bolts in concentric rings carry identical shear stress. Rigid flange kinematics require bolt shear to vary linearly with radius ( τ ∝ R \tau \propto R τ ∝ R ). Outer bolts always carry the maximum stress.