Study guide
13.3 Influence Lines for Determinate and Indeterminate Structures
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
13.3 Influence Lines for Determinate and Indeterminate Structures
Key Takeaways Explain This Topic AI
An Influence Line (IL) plots the variation of a specific internal response (reaction, shear, or bending moment at a fixed cross-section) as a dimensionless unit concentrated load moves across the structure.
The Müller-Breslau Principle states that the influence line for any reaction or internal force represents the deflected elastic curve obtained by removing the restraint corresponding to that force and imposing a unit virtual displacement.
Influence lines for statically determinate structures always consist of piecewise linear straight segments, whereas influence lines for indeterminate structures are smooth continuous elastic curves.
Under a moving train of concentrated wheel loads, the absolute maximum bending moment in a simply supported beam occurs under a critical heavy wheel when the beam centerline bisects the distance between that wheel and the resultant (R) of the load train.
Dynamic effects from moving vehicular traffic are accounted for by the dynamic load allowance or impact factor (IM), given classically by I = 15.24 / (L + 38) ≤ 0.30.
Last updated: October 2026
13.3 Influence Lines for Determinate and Indeterminate Structures
Bridge girders, crane runways, and industrial highway structures are subjected to transient vehicular moving loads. Unlike buildings carrying stationary dead loads, bridge design requires structural engineers to determine which vehicle positions produce governing maximum internal reactions, shears, and moments. The primary analytical tool for this task is the Influence Line (IL) .
1. Concept of the Influence Line
An Influence Line is a graph showing the variation of a specific structural reaction or internal action (shear force, bending moment, axial force, or deflection) at one specific fixed cross-section as a single unit vertical concentrated load ( 1 kN 1\text{ kN} 1 kN ) traverses across the span.
Influence Lines vs. Shear and Moment Diagrams
A frequent source of confusion among candidates is the distinction between Shear Force / Bending Moment Diagrams (SFD/BMD) and Influence Lines:
Attribute Shear & Moment Diagrams (SFD / BMD) Influence Line (IL)
Load Status Stationary / Fixed at specific locations on the beam Moving unit load ( 1 kN 1\text{ kN} 1 kN ) changing position x x x
Point of Interest Plots response along every point across the beam length Examines response at one single fixed cross-section C C C
Abscissa ( x x x -axis) Position along the beam length where internal action exists Position of the moving unit load along the span
Ordinate ( y y y -axis) Value of shear ( V V V ) or moment ( M M M ) at that point Response at fixed point C C C caused by load at position x x x
Units Force ( kN \text{kN} kN ) or Moment ( kN ⋅ m \text{kN}\cdot\text{m} kN ⋅ m ) Dimensionless for reactions/shear; Length ( m \text{m} m ) for moments
2. Influence Lines for Statically Determinate Beams
Consider a simply supported beam A B AB A B of span L L L . A unit load ( 1 kN 1\text{ kN} 1 kN ) moves from x = 0 x = 0 x = 0 (support A A A ) to x = L x = L x = L (support B B B ).
Support Reactions
Reaction R A R_A R A : When the load is at x x x , summing moments about B B B gives R A ( L ) − 1 ( L − x ) = 0 R_A(L) - 1(L - x) = 0 R A ( L ) − 1 ( L − x ) = 0 : I L ( R A ) = 1 − x L IL(R_A) = 1 - \frac{x}{L} I L ( R A ) = 1 − L x Shape: Linear triangle, starting at + 1.0 +1.0 + 1.0 at A A A ( x = 0 x=0 x = 0 ) and decreasing to 0.0 0.0 0.0 at B B B ( x = L x=L x = L ).
Reaction R B R_B R B : Summing moments about A A A gives R B ( L ) − 1 ( x ) = 0 R_B(L) - 1(x) = 0 R B ( L ) − 1 ( x ) = 0 : I L ( R B ) = x L IL(R_B) = \frac{x}{L} I L ( R B ) = L x Shape: Linear triangle, starting at 0.0 0.0 0.0 at A A A and rising to + 1.0 +1.0 + 1.0 at B B B .
Shear at Section C C C ( x = a x = a x = a from left support, b = L − a b = L - a b = L − a from right support)
When the unit load is to the left of C C C ( 0 ≤ x < a 0 \le x < a 0 ≤ x < a ): V C = − R B = − x L V_C = -R_B = -\frac{x}{L} V C = − R B = − L x At x = 0 x = 0 x = 0 , V C = 0 V_C = 0 V C = 0 . As x → a − x \to a^- x → a − , V C = − a L V_C = -\frac{a}{L} V C = − L a .
When the unit load is to the right of C C C ( a < x ≤ L a < x \le L a < x ≤ L ): V C = + R A = 1 − x L = + b L V_C = +R_A = 1 - \frac{x}{L} = +\frac{b}{L} V C = + R A = 1 − L x = + L b At x → a + x \to a^+ x → a + , V C = + b L V_C = +\frac{b}{L} V C = + L b . At x = L x = L x = L , V C = 0 V_C = 0 V C = 0 .
Discontinuity: At section C C C , the influence line drops by exactly 1.0 1.0 1.0 unit: Δ V = + b L − ( − a L ) = a + b L = 1.0 \Delta V = +\frac{b}{L} - \left(-\frac{a}{L}\right) = \frac{a+b}{L} = 1.0 Δ V = + L b − ( − L a ) = L a + b = 1.0
Bending Moment at Section C C C ( x = a x = a x = a )
When the unit load is to the left of C C C ( 0 ≤ x ≤ a 0 \le x \le a 0 ≤ x ≤ a ): M C = R B ⋅ b = ( x L ) b = b x L M_C = R_B \cdot b = \left(\frac{x}{L}\right) b = \frac{b x}{L} M C = R B ⋅ b = ( L x ) b = L b x
When the unit load is to the right of C C C ( a ≤ x ≤ L a \le x \le L a ≤ x ≤ L ): M C = R A ⋅ a = ( 1 − x L ) a = a ( L − x ) L M_C = R_A \cdot a = \left(1 - \frac{x}{L}\right) a = \frac{a (L - x)}{L} M C = R A ⋅ a = ( 1 − L x ) a = L a ( L − x )
Peak Ordinate: At x = a x = a x = a , both equations yield the maximum moment ordinate: y max = a b L y_{\text{max}} = \frac{a b}{L} y max = L ab Shape: A triangle with apex ordinate a b L \frac{ab}{L} L ab at section C C C , sloping linearly to zero at supports A A A and B B B .
3. The Müller-Breslau Principle
Heinrich Müller-Breslau formulated in 1886 a powerful geometric theorem for constructing qualitative and quantitative influence lines:
Müller-Breslau Principle: The influence line for any reaction or internal force of a structure is proportional to the deflected shape of the structure obtained by removing the restraint corresponding to that action and introducing a corresponding unit virtual displacement (or rotation) in the direction of the action.
Application to Determinate vs. Indeterminate Structures
Statically Determinate Structures: Removing a restraint converts the structure into a kinematically determinate mechanism (rigid bodies connected by hinges). Because rigid segments cannot bend, the resulting deflected shape consists entirely of straight line segments .
Statically Indeterminate Structures: Removing one constraint leaves the remaining primary structure statically stable. Applying a unit displacement induces elastic bending. Therefore, the influence line for any action in an indeterminate structure consists of smooth continuous elastic curves . Qualitative IL for Middle Reaction R_B of a Two-Span Continuous Beam:
[A]▲================[B]▲================[C]▲
Step 1: Remove vertical restraint at support B.
Step 2: Push joint B upward by unit displacement Δ_B = 1.0.
Deflected Elastic Shape (= IL for R_B):
- +1.0
- ▲
- / \
- [A]▲--/ \--▲[C]
- (Continuous smooth curve, concave downward over B)
- 4. Quantitative Application of Influence Lines
Once the influence line for an internal action F F F is established, the total response under any service loading train is computed by superposition:
Concentrated Moving Loads
For a series of discrete concentrated wheel loads P 1 , P 2 , … , P n P_1, P_2, \dots, P_n P 1 , P 2 , … , P n located at positions corresponding to influence ordinates y 1 , y 2 , … , y n y_1, y_2, \dots, y_n y 1 , y 2 , … , y n :
- F = ∑ i = 1 n P i y i F = \sum_{i=1}^n P_i y_i F = ∑ i = 1 n P i y i
- Uniform Distributed Live Load ( w L L w_{LL} w LL )
For a uniform live load w L L w_{LL} w LL extending from x 1 x_1 x 1 to x 2 x_2 x 2 :
F = ∫ x 1 x 2 w L L y ( x ) d x = w L L × ( Net Area under IL between x 1 and x 2 ) F = \int_{x_1}^{x_2} w_{LL} y(x) dx = w_{LL} \times (\text{Net Area under IL between } x_1 \text{ and } x_2) F = ∫ x 1 x 2 w LL y ( x ) d x = w LL × ( Net Area under IL between x 1 and x 2 )
To obtain the maximum positive effect , place uniform live load only over segments where the influence line is positive.
To obtain the maximum negative effect , place uniform live load only over segments where the influence line is negative.
5. Moving Load Analysis: Absolute Maximum Effects
In bridge design, vehicular traffic consists of wheel load trains (such as the standard Philippine DPWH / AASHTO truck). Structural engineers must identify the absolute maximum bending moment ( M abs,max M_{\text{abs,max}} M abs,max ) and absolute maximum shear ( V abs,max V_{\text{abs,max}} V abs,max ) that can develop anywhere along the span.
Absolute Maximum Shear ( V abs,max V_{\text{abs,max}} V abs,max )
For simply supported spans, absolute maximum shear always occurs at one of the end supports (where the influence ordinate is + 1.0 +1.0 + 1.0 ). The heaviest wheel load is positioned directly over the support, with trailing loads placed within the span on the steepest branch of the influence line.
Absolute Maximum Bending Moment: The Centerline Bisection Theorem
The absolute maximum bending moment does not generally occur at midspan ( L / 2 L/2 L /2 ), nor does it occur under the resultant R R R of the loads. It occurs under one of the critical wheel loads near the resultant.
The Bisection Rule:
Compute the magnitude of the total resultant force of the wheel group: R = ∑ P i R = \sum P_i R = ∑ P i .
Determine the location of the resultant x ˉ R \bar{x}_R x ˉ R by taking moments about the lead wheel: x ˉ R = ∑ P i x i R \bar{x}_R = \frac{\sum P_i x_i}{R} x ˉ R = R ∑ P i x i .
Identify the critical heavy wheel load P k P_k P k located closest to the resultant R R R . Let d d d be the distance between P k P_k P k and R R R .
Placement for Maximum Moment: Position the load train on the beam such that the centerline of the beam bisects the distance d d d between the critical wheel load P k P_k P k and the resultant R R R :
Distance from nearest support to P k = L 2 − d 2 \text{Distance from nearest support to } P_k = \frac{L}{2} - \frac{d}{2} Distance from nearest support to P k = 2 L − 2 d Distance from nearest support to R = L 2 + d 2 \text{Distance from nearest support to } R = \frac{L}{2} + \frac{d}{2} Distance from nearest support to R = 2 L + 2 d
Calculate the bending moment directly beneath load P k P_k P k under this placement to establish M abs,max M_{\text{abs,max}} M abs,max .
Impact Factor / Dynamic Load Allowance ( I M IM I M )
Vehicular motion, surface roughness, and engine vibration produce dynamic amplification. In classical Philippine bridge engineering (AASHTO Standard Specifications), the impact fraction I I I is calculated as:
I = 15.24 L + 38 ≤ 0.30 I = \frac{15.24}{L + 38} \le 0.30 I = L + 38 15.24 ≤ 0.30
where L L L is the loaded span length in meters. In AASHTO LRFD Bridge Specifications, the dynamic load allowance is taken as a fixed percentage: I M = 33 % IM = 33\% I M = 33% for bridge deck and girder strength limit states, and 15 % 15\% 15% for fatigue.
6. Pattern Loading of Continuous Beams and Frames
Influence lines also explain the TOS competency "compute the maximum reactions with and without pattern loading." For a continuous beam, the influence line for positive moment in a span is positive over that span and over alternate spans, and negative over the adjacent spans. Live load should therefore be placed only where the influence ordinates have the desired sign.
ACI 318-14 (Section 6.4.2), which NSCP 2015 follows, allows the live load arrangement to be limited to two cases:
- Effect sought Factored live load placement (dead load on all spans)
- Maximum positive moment near midspan of a span On that span and on alternate spans
- Maximum negative moment at a support On the two adjacent spans only
The same logic gives the maximum reaction at an interior support: load the two spans that meet at that support, then every other span beyond them.
ACI approximate moment and shear coefficients
For continuous beams and one-way slabs with at least two spans, roughly equal spans (the larger of two adjacent spans not more than 20% longer than the shorter), uniform load, and unfactored live load not exceeding three times the dead load, ACI 318-14 Section 6.5 permits M u = C m w u ℓ n 2 M_u = C_m w_u \ell_n^2 M u = C m w u ℓ n 2 and V u = C v w u ℓ n / 2 V_u = C_v w_u \ell_n / 2 V u = C v w u ℓ n /2 :
- Location Coefficient
- Positive moment, end span, discontinuous end integral with support 1 / 14 1/14 1/14
- Positive moment, end span, discontinuous end unrestrained 1 / 11 1/11 1/11
- Positive moment, interior spans 1 / 16 1/16 1/16
- Negative moment at exterior face of first interior support, two spans 1 / 9 1/9 1/9
- Negative moment at exterior face of first interior support, more than two spans 1 / 10 1/10 1/10
- Negative moment at other faces of interior supports 1 / 11 1/11 1/11
- Shear at exterior face of first interior support 1.15 w u ℓ n / 2 1.15 w_u \ell_n / 2 1.15 w u ℓ n /2
- Shear at faces of all other supports w u ℓ n / 2 w_u \ell_n / 2 w u ℓ n /2
Example. A three-span continuous beam has clear spans of 6.0 m 6.0\text{ m} 6.0 m and w u = 40 kN/m w_u = 40\text{ kN/m} w u = 40 kN/m . The negative moment at the exterior face of the first interior support is w u ℓ n 2 / 10 = 40 ( 36 ) / 10 = 144 kN ⋅ m w_u \ell_n^2 / 10 = 40(36)/10 = 144\text{ kN}\cdot\text{m} w u ℓ n 2 /10 = 40 ( 36 ) /10 = 144 kN ⋅ m . The interior-span positive moment is 40 ( 36 ) / 16 = 90 kN ⋅ m 40(36)/16 = 90\text{ kN}\cdot\text{m} 40 ( 36 ) /16 = 90 kN ⋅ m .
- 7. Comprehensive Worked Example
- Worked Example: Absolute Maximum Moment Under a Three-Axle Truck
Problem: A simply supported bridge girder has a span of L = 20.0 m L = 20.0\text{ m} L = 20.0 m . It is traversed by a three-axle truck moving from left to right. The wheel loads are P 1 = 50.0 kN P_1 = 50.0\text{ kN} P 1 = 50.0 kN (front axle), P 2 = 150.0 kN P_2 = 150.0\text{ kN} P 2 = 150.0 kN (drive axle, 4.0 m 4.0\text{ m} 4.0 m behind P 1 P_1 P 1 ), and P 3 = 150.0 kN P_3 = 150.0\text{ kN} P 3 = 150.0 kN (rear axle, 6.0 m 6.0\text{ m} 6.0 m behind P 2 P_2 P 2 ). Determine: (a) resultant location, (b) critical truck placement, and (c) the absolute maximum bending moment M abs,max M_{\text{abs,max}} M abs,max . P1 = 50 kN P2 = 150 kN P3 = 150 kN
- ↓ ↓ ↓
- |------ 4.0 m -----|--------- 6.0 m --------|
Solution:
Step 1: Resultant Force and Location: R = P 1 + P 2 + P 3 = 50.0 + 150.0 + 150.0 = 350.0 kN R = P_1 + P_2 + P_3 = 50.0 + 150.0 + 150.0 = 350.0\text{ kN} R = P 1 + P 2 + P 3 = 50.0 + 150.0 + 150.0 = 350.0 kN Taking moments about front axle P 1 P_1 P 1 : R ⋅ x ˉ = 50 ( 0 ) + 150 ( 4.0 ) + 150 ( 4.0 + 6.0 ) = 600 + 1500 = 2100 kN ⋅ m R \cdot \bar{x} = 50(0) + 150(4.0) + 150(4.0 + 6.0) = 600 + 1500 = 2100\text{ kN}\cdot\text{m} R ⋅ x ˉ = 50 ( 0 ) + 150 ( 4.0 ) + 150 ( 4.0 + 6.0 ) = 600 + 1500 = 2100 kN ⋅ m x ˉ = 2100 350 = 6.0 m behind P 1 \bar{x} = \frac{2100}{350} = 6.0\text{ m} \text{ behind } P_1 x ˉ = 350 2100 = 6.0 m behind P 1 Since P 2 P_2 P 2 is located 4.0 m 4.0\text{ m} 4.0 m behind P 1 P_1 P 1 , the resultant R R R is located: d = 6.0 − 4.0 = 2.0 m behind P 2 d = 6.0 - 4.0 = 2.0\text{ m} \text{ behind } P_2 d = 6.0 − 4.0 = 2.0 m behind P 2 (Between P 2 P_2 P 2 and P 3 P_3 P 3 , closer to P 2 P_2 P 2 ).
Step 2: Centerline Bisection Placement: The closest heavy load to the resultant is P 2 = 150 kN P_2 = 150\text{ kN} P 2 = 150 kN (distance d = 2.0 m d = 2.0\text{ m} d = 2.0 m ). The beam centerline ( L / 2 = 10.0 m L/2 = 10.0\text{ m} L /2 = 10.0 m ) must bisect the distance between P 2 P_2 P 2 and R R R :
Distance of P 2 P_2 P 2 from left support A A A : x 2 = L 2 − d 2 = 10.0 − 2.0 2 = 9.0 m x_2 = \frac{L}{2} - \frac{d}{2} = 10.0 - \frac{2.0}{2} = 9.0\text{ m} x 2 = 2 L − 2 d = 10.0 − 2 2.0 = 9.0 m
Resultant R R R is at x R = 9.0 + 2.0 = 11.0 m x_R = 9.0 + 2.0 = 11.0\text{ m} x R = 9.0 + 2.0 = 11.0 m from A A A . (Centerline is at 10.0 m 10.0\text{ m} 10.0 m , exactly halfway between 9.0 m 9.0\text{ m} 9.0 m and 11.0 m 11.0\text{ m} 11.0 m !).
Location of all axles:
P 1 P_1 P 1 is at x 1 = 9.0 − 4.0 = 5.0 m x_1 = 9.0 - 4.0 = 5.0\text{ m} x 1 = 9.0 − 4.0 = 5.0 m from A A A .
P 2 P_2 P 2 is at x 2 = 9.0 m x_2 = 9.0\text{ m} x 2 = 9.0 m from A A A .
P 3 P_3 P 3 is at x 3 = 9.0 + 6.0 = 15.0 m x_3 = 9.0 + 6.0 = 15.0\text{ m} x 3 = 9.0 + 6.0 = 15.0 m from A A A . Verification: All three axles lie within the 20.0 m 20.0\text{ m} 20.0 m span ( 0 < 5.0 , 9.0 , 15.0 < 20.0 0 < 5.0, 9.0, 15.0 < 20.0 0 < 5.0 , 9.0 , 15.0 < 20.0 ).
Step 3: Support Reactions and Maximum Moment: Compute reaction R A R_A R A using the resultant R = 350 kN R = 350\text{ kN} R = 350 kN at x R = 11.0 m x_R = 11.0\text{ m} x R = 11.0 m : R A = R ( L − x R ) L = 350 ( 20.0 − 11.0 ) 20.0 = 350 ( 9.0 ) 20.0 = 157.5 kN R_A = \frac{R (L - x_R)}{L} = \frac{350 (20.0 - 11.0)}{20.0} = \frac{350 (9.0)}{20.0} = 157.5\text{ kN} R A = L R ( L − x R ) = 20.0 350 ( 20.0 − 11.0 ) = 20.0 350 ( 9.0 ) = 157.5 kN Compute bending moment under load P 2 P_2 P 2 at x 2 = 9.0 m x_2 = 9.0\text{ m} x 2 = 9.0 m : M abs,max = R A ⋅ x 2 − P 1 ( x 2 − x 1 ) M_{\text{abs,max}} = R_A \cdot x_2 - P_1 (x_2 - x_1) M abs,max = R A ⋅ x 2 − P 1 ( x 2 − x 1 ) M abs,max = 157.5 × 9.0 − 50.0 × ( 9.0 − 5.0 ) M_{\text{abs,max}} = 157.5 \times 9.0 - 50.0 \times (9.0 - 5.0) M abs,max = 157.5 × 9.0 − 50.0 × ( 9.0 − 5.0 ) M abs,max = 1417.5 − 200.0 = 1217.5 kN ⋅ m M_{\text{abs,max}} = 1417.5 - 200.0 = 1217.5\text{ kN}\cdot\text{m} M abs,max = 1417.5 − 200.0 = 1217.5 kN ⋅ m
8. Licensure Exam Pitfalls & Review Notes
Warning
Pitfall 1: Assuming Absolute Maximum Moment Occurs at Midspan A common board exam blunder is placing the resultant or heaviest wheel at midspan ( L / 2 L/2 L /2 ). Midspan moment is rarely the absolute maximum. The absolute peak always occurs under a specific wheel load offset from midspan by d / 2 d/2 d /2 .
Caution
Pitfall 2: Axles Rolling Off the Span When applying the bisection theorem, always verify that all assumed wheels remain on the girder! If positioning the truck causes the front axle to roll off the span ( x < 0 x < 0 x < 0 ), you must recompute the resultant force R R R and location x ˉ \bar{x} x ˉ using only the axles remaining on the span.
Tip
Pitfall 3: Müller-Breslau Shear Discontinuity When sketching shear influence lines via the Müller-Breslau principle, cut the beam and introduce a unit relative vertical translation without allowing relative rotation. The two cut ends must remain strictly parallel to each other.