Study guide
13.2 Moment Distribution Method and Slope Deflection
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
13.2 Moment Distribution Method and Slope Deflection
Key Takeaways Explain This Topic AI
The Slope Deflection Method expresses internal end moments as functions of joint rotations (θ_i, θ_j), chord drift translation (ψ = Δ/L), and Fixed-End Moments (FEM), formulating equilibrium equations (ΣM_i = 0) for each kinematic degree of freedom.
Fixed-End Moments for standard spans include -wL²/12 and +wL²/12 for full uniform loads, and -Pab²/L² and +Pa²b/L² for unsymmetrical concentrated loads under standard clockwise-positive conventions.
The Moment Distribution Method (Hardy Cross Method) solves indeterminate structures through iterative relaxation cycles, distributing joint unbalanced moments in proportion to member stiffness factors (K = 4EI/L for far end fixed, K = 3EI/L for far end pinned).
The carry-over factor (COF) transmits exactly +1/2 of the distributed balancing moment to an opposite fixed joint, while transmitting zero (COF = 0) to a pinned or roller end when modified stiffness K = 3EI/L is utilized.
Member stiffness factors can be modified to account for structural symmetry: K = 2EI/L for symmetric loading (zero slope at axis of symmetry) and K = 6EI/L for antisymmetric loading (zero moment at axis of symmetry).
Last updated: October 2026
13.2 Moment Distribution Method and Slope Deflection
While the Force Method treats redundant forces as primary unknowns, displacement methods formulate unknown joint rotations ( θ \theta θ ) and translations ( Δ \Delta Δ ). Because the Degree of Kinematic Indeterminacy ( D K I DKI DK I ) is often smaller than the static indeterminacy in multi-bay continuous systems, displacement methods are exceptionally well-suited for rigid frames. This section explores the Slope Deflection Method (the analytical precursor to modern stiffness matrix analysis) and the Moment Distribution Method (the renowned iterative relaxation algorithm developed by Hardy Cross in 1930).
1. The Slope Deflection Method
Formulated by George A. Maney in 1915, the Slope Deflection Method expresses the internal bending moments at the ends of each structural member as linear functions of member end rotations, chord displacement, and applied span loads.
The Fundamental Slope Deflection Equations
For a prismatic member i j ij ij of length L L L and flexural rigidity E I EI E I :
M i j = FEM i j + 2 E I L ( 2 θ i + θ j − 3 Δ L ) M_{ij} = \text{FEM}_{ij} + \frac{2EI}{L} \left( 2\theta_i + \theta_j - \frac{3\Delta}{L} \right) M ij = FEM ij + L 2 E I ( 2 θ i + θ j − L 3Δ ) M j i = FEM j i + 2 E I L ( 2 θ j + θ i − 3 Δ L ) M_{ji} = \text{FEM}_{ji} + \frac{2EI}{L} \left( 2\theta_j + \theta_i - \frac{3\Delta}{L} \right) M ji = FEM ji + L 2 E I ( 2 θ j + θ i − L 3Δ )
Defining the chord rotation as ψ = Δ L \psi = \frac{\Delta}{L} ψ = L Δ :
M i j = FEM i j + 2 E I L ( 2 θ i + θ j − 3 ψ ) M_{ij} = \text{FEM}_{ij} + \frac{2EI}{L} \left( 2\theta_i + \theta_j - 3\psi \right) M ij = FEM ij + L 2 E I ( 2 θ i + θ j − 3 ψ )
Where:
M i j M_{ij} M ij = internal bending moment acting on the end of member i j ij ij at joint i i i ( clockwise positive ).
FEM i j \text{FEM}_{ij} FEM ij = Fixed-End Moment at end i i i resulting from transverse span loads ( clockwise positive ).
θ i , θ j \theta_i, \theta_j θ i , θ j = joint rotations at ends i i i and j j j in radians ( clockwise positive ).
Δ \Delta Δ = relative lateral displacement (drift) between ends i i i and j j j perpendicular to the member axis.
ψ = Δ / L \psi = \Delta / L ψ = Δ/ L = rigid-body chord rotation angle ( clockwise positive ).
Modified Equation for a Pinned Far End
If far end j j j is pinned or on a roller support, the end moment M j i = 0 M_{ji} = 0 M ji = 0 . Substituting M j i = 0 M_{ji} = 0 M ji = 0 eliminates θ j \theta_j θ j from the formulation, yielding the modified slope deflection equation for end i i i :
M i j = FEM i j − FEM j i 2 + 3 E I L ( θ i − ψ ) M_{ij} = \text{FEM}_{ij} - \frac{\text{FEM}_{ji}}{2} + \frac{3EI}{L} (\theta_i - \psi) M ij = FEM ij − 2 FEM ji + L 3 E I ( θ i − ψ )
This modification reduces the number of simultaneous linear equations by one for every external pinned support.
2. Table of Fixed-End Moments (FEM)
Fixed-end moments are internal reactions developed at fully clamped boundaries. In slope deflection analysis, clockwise end moments are positive and counterclockwise moments are negative.
Loading Condition FEM A B \text{FEM}_{AB} FEM A B (Left End) FEM B A \text{FEM}_{BA} FEM B A (Right End)
Uniform Load w w w over entire span L L L − w L 2 12 -\frac{wL^2}{12} − 12 w L 2 + w L 2 12 +\frac{wL^2}{12} + 12 w L 2
Central Point Load P P P at L / 2 L/2 L /2 − P L 8 -\frac{PL}{8} − 8 P L + P L 8 +\frac{PL}{8} + 8 P L
Point Load P P P at distance a a a from A A A , b b b from B B B − P a b 2 L 2 -\frac{P a b^2}{L^2} − L 2 P a b 2 + P a 2 b L 2 +\frac{P a^2 b}{L^2} + L 2 P a 2 b
Two Equal Concentrated Loads P P P at third-points ( L / 3 L/3 L /3 ) − 2 P L 9 -\frac{2PL}{9} − 9 2 P L + 2 P L 9 +\frac{2PL}{9} + 9 2 P L
Triangular Load: 0 0 0 at A A A increasing to w w w at B B B − w L 2 30 -\frac{wL^2}{30} − 30 w L 2 + w L 2 20 +\frac{wL^2}{20} + 20 w L 2
Symmetric Triangular Load: peak w w w at center − 5 w L 2 96 -\frac{5wL^2}{96} − 96 5 w L 2 + 5 w L 2 96 +\frac{5wL^2}{96} + 96 5 w L 2
Applied External Couple M 0 M_0 M 0 at distance a a a from A A A M 0 b ( 2 a − b ) L 2 \frac{M_0 b (2a - b)}{L^2} L 2 M 0 b ( 2 a − b ) M 0 a ( 2 b − a ) L 2 \frac{M_0 a (2b - a)}{L^2} L 2 M 0 a ( 2 b − a )
- 3. Analysis of Frames: Non-Sway vs. Sidesway
- Non-Sway Frames
A frame is prevented from sidesway if:
It is symmetrically geometry-loaded and symmetrically supported, or
It is laterally braced against displacement by shear walls, bracing trusses, or external rigid supports.
In non-sway analysis, chord rotation ψ = 0 \psi = 0 ψ = 0 . The only unknowns are the joint rotations θ \theta θ . For each free joint i i i , formulate joint equilibrium:
- ∑ M i = 0 ⟹ ∑ j M i j = 0 \sum M_i = 0 \implies \sum_{j} M_{ij} = 0 ∑ M i = 0 ⟹ ∑ j M ij = 0
- Sway Frames
When a frame is unbraced, unsymmetrical, or subjected to lateral loads, lateral drift Δ \Delta Δ occurs. Each independent lateral translation introduces an unknown chord rotation ψ = Δ / h \psi = \Delta / h ψ = Δ/ h . To solve for ψ \psi ψ , an additional story shear equation is required from horizontal equilibrium:
∑ H = 0 ⟹ ∑ V columns + P lateral = 0 \sum H = 0 \implies \sum V_{\text{columns}} + P_{\text{lateral}} = 0 ∑ H = 0 ⟹ ∑ V columns + P lateral = 0
For any column A B AB A B of height h h h with end moments M A B M_{AB} M A B and M B A M_{BA} M B A :
- V A B = M A B + M B A h V_{AB} = \frac{M_{AB} + M_{BA}}{h} V A B = h M A B + M B A
- 4. The Moment Distribution Method (Hardy Cross)
The Moment Distribution Method solves continuous beams and rigid frames through successive numerical approximations without setting up simultaneous equations. Joints are initially locked against rotation, then systematically unlocked, balanced, and re-locked until unbalanced moments diminish to zero.
Member Stiffness Factor ( K K K )
The flexural stiffness factor K K K represents the moment required to produce a unit rotation ( θ = 1 rad \theta = 1\text{ rad} θ = 1 rad ) at one end while the far end boundary is maintained:
Far End Fixed: K = 4 E I L K = \frac{4EI}{L} K = L 4 E I (or relative stiffness k = I L k = \frac{I}{L} k = L I ).
Far End Pinned or Roller: K = 3 E I L K = \frac{3EI}{L} K = L 3 E I (or relative stiffness k = 3 4 I L = 0.75 I L k = \frac{3}{4} \frac{I}{L} = 0.75 \frac{I}{L} k = 4 3 L I = 0.75 L I ).
Distribution Factor ( D F DF D F )
The Distribution Factor at a joint defines the proportion of an unbalanced moment absorbed by each framing member:
D F i = K i ∑ K DF_i = \frac{K_i}{\sum K} D F i = ∑ K K i
At an ideal fixed wall support: K = ∞ ⟹ D F = 0 K = \infty \implies DF = 0 K = ∞ ⟹ D F = 0 (the fixed support absorbs all moment without rotating).
At an exterior pinned/roller end: K support = 0 ⟹ D F = 1.0 K_{\text{support}} = 0 \implies DF = 1.0 K support = 0 ⟹ D F = 1.0 .
At an interior rigid joint connecting m m m members: ∑ i = 1 m D F i = 1.0 \sum_{i=1}^m DF_i = 1.0 ∑ i = 1 m D F i = 1.0 .
Carry-Over Factor ( C O F COF COF )
When a moment M M M is applied to balance a joint, an induced moment travels to the opposite end of the member:
To a rigidly fixed far end: C O F = + 0.50 COF = +0.50 COF = + 0.50 .
To a pinned or roller far end (when modified stiffness 3 E I / L 3EI/L 3 E I / L is used): C O F = 0 COF = 0 COF = 0 .
Symmetrical Loading Simplifications
When a structure and its loading possess geometric symmetry, computational effort is substantially reduced by analyzing half the structure using modified stiffness:
Symmetric Deformation (Equal and opposite rotations, θ j = − θ i \theta_j = -\theta_i θ j = − θ i ): Axis of symmetry behaves as a fixed guided support. Modified stiffness is: K sym = 2 E I L = 0.5 K standard K_{\text{sym}} = \frac{2EI}{L} = 0.5 K_{\text{standard}} K sym = L 2 E I = 0.5 K standard
Antisymmetric Deformation (Identical rotations, θ j = θ i \theta_j = \theta_i θ j = θ i ): Axis of symmetry behaves as a simple pin ( M = 0 M = 0 M = 0 ). Modified stiffness is: K antisym = 6 E I L = 1.5 K standard K_{\text{antisym}} = \frac{6EI}{L} = 1.5 K_{\text{standard}} K antisym = L 6 E I = 1.5 K standard
- 5. Comprehensive Worked Example
- Worked Example: Two-Span Continuous Beam with Pinned Exterior End
Problem: A continuous beam A B C ABC A BC rests on simple supports at B B B and C C C and is rigidly clamped at support A A A . Span A B = 6.0 m AB = 6.0\text{ m} A B = 6.0 m with flexural rigidity E I EI E I ; Span B C = 4.0 m BC = 4.0\text{ m} BC = 4.0 m with flexural rigidity E I EI E I . Span A B AB A B carries a uniform load w = 24.0 kN/m w = 24.0\text{ kN/m} w = 24.0 kN/m . Span B C BC BC carries a central concentrated load P = 40.0 kN P = 40.0\text{ kN} P = 40.0 kN at mid-span. Determine the final support moments using the Moment Distribution Method with modified stiffness for pinned end C C C . [Fixed A]======== 6.0 m ========▲ B ======== 4.0 m ========▲ C (Pin)
w = 24 kN/m P = 40 kN
Solution:
Step 1: Member Stiffness and Distribution Factors:
Member B A BA B A (far end A A A is fixed): K B A = 4 E I L = 4 E I 6.0 = 0.667 E I K_{BA} = \frac{4EI}{L} = \frac{4EI}{6.0} = 0.667 EI K B A = L 4 E I = 6.0 4 E I = 0.667 E I .
Member B C BC BC (far end C C C is pinned, using modified stiffness): K B C = 3 E I L = 3 E I 4.0 = 0.750 E I K_{BC} = \frac{3EI}{L} = \frac{3EI}{4.0} = 0.750 EI K BC = L 3 E I = 4.0 3 E I = 0.750 E I .
Total stiffness at Joint B B B : ∑ K B = 0.667 E I + 0.750 E I = 1.417 E I \sum K_B = 0.667 EI + 0.750 EI = 1.417 EI ∑ K B = 0.667 E I + 0.750 E I = 1.417 E I .
Distribution Factors at B B B : D F B A = 0.667 1.417 = 0.471 DF_{BA} = \frac{0.667}{1.417} = 0.471 D F B A = 1.417 0.667 = 0.471 D F B C = 0.750 1.417 = 0.529 DF_{BC} = \frac{0.750}{1.417} = 0.529 D F BC = 1.417 0.750 = 0.529 Check: 0.471 + 0.529 = 1.000 0.471 + 0.529 = 1.000 0.471 + 0.529 = 1.000 .
At support A A A (fixed): D F A B = 0 DF_{AB} = 0 D F A B = 0 .
At support C C C (pinned): Using K = 3 E I / L K = 3EI/L K = 3 E I / L , C C C is released initially; D F C B = 1.0 DF_{CB} = 1.0 D F CB = 1.0 , C O F B → C = 0 COF_{B \to C} = 0 CO F B → C = 0 .
Step 2: Fixed-End Moments (FEM):
Span A B AB A B ( w = 24 kN/m w = 24\text{ kN/m} w = 24 kN/m , L = 6 m L = 6\text{ m} L = 6 m ): FEM A B = − w L 2 12 = − 24 ( 6 2 ) 12 = − 72.00 kN ⋅ m \text{FEM}_{AB} = -\frac{wL^2}{12} = -\frac{24(6^2)}{12} = -72.00\text{ kN}\cdot\text{m} FEM A B = − 12 w L 2 = − 12 24 ( 6 2 ) = − 72.00 kN ⋅ m FEM B A = + w L 2 12 = + 72.00 kN ⋅ m \text{FEM}_{BA} = +\frac{wL^2}{12} = +72.00\text{ kN}\cdot\text{m} FEM B A = + 12 w L 2 = + 72.00 kN ⋅ m
Span B C BC BC ( P = 40 kN P = 40\text{ kN} P = 40 kN , L = 4 m L = 4\text{ m} L = 4 m , pin at C C C ):
Standard fixed-end moment is FEM B C = − P L 8 = − 40 ( 4 ) 8 = − 20.00 kN ⋅ m \text{FEM}_{BC} = -\frac{PL}{8} = -\frac{40(4)}{8} = -20.00\text{ kN}\cdot\text{m} FEM BC = − 8 P L = − 8 40 ( 4 ) = − 20.00 kN ⋅ m , and FEM C B = + 20.00 kN ⋅ m \text{FEM}_{CB} = +20.00\text{ kN}\cdot\text{m} FEM CB = + 20.00 kN ⋅ m .
Releasing pinned joint C C C upfront, the modified fixed-end moment at B B B is: FEM B C ′ = FEM B C − 1 2 FEM C B = − 20.00 − 1 2 ( + 20.00 ) = − 30.00 kN ⋅ m \text{FEM}'_{BC} = \text{FEM}_{BC} - \frac{1}{2} \text{FEM}_{CB} = -20.00 - \frac{1}{2}(+20.00) = -30.00\text{ kN}\cdot\text{m} FEM BC ′ = FEM BC − 2 1 FEM CB = − 20.00 − 2 1 ( + 20.00 ) = − 30.00 kN ⋅ m FEM C B ′ = 0.00 kN ⋅ m \text{FEM}'_{CB} = 0.00\text{ kN}\cdot\text{m} FEM CB ′ = 0.00 kN ⋅ m
Step 3: Moment Distribution Table:
- Joint A B B C
- Member AB BA BC CB
- DF 0 0.471 0.529 1.0
- FEM -72.00 +72.00 -30.00 0.00
- Balance B — -19.78 -22.22 —
- Carry-Over -9.89 — — 0.00 ( C O F = 0 COF=0 COF = 0 )
- Final Moments -81.89 +52.22 -52.22 0.00
Computation Detail for Joint B Balance:
Unbalanced moment at B = + 72.00 + ( − 30.00 ) = + 42.00 kN ⋅ m B = +72.00 + (-30.00) = +42.00\text{ kN}\cdot\text{m} B = + 72.00 + ( − 30.00 ) = + 42.00 kN ⋅ m .
Balancing moments: Δ M B A = − 0.471 × ( + 42.00 ) = − 19.78 kN ⋅ m \Delta M_{BA} = -0.471 \times (+42.00) = -19.78\text{ kN}\cdot\text{m} Δ M B A = − 0.471 × ( + 42.00 ) = − 19.78 kN ⋅ m ; Δ M B C = − 0.529 × ( + 42.00 ) = − 22.22 kN ⋅ m \Delta M_{BC} = -0.529 \times (+42.00) = -22.22\text{ kN}\cdot\text{m} Δ M BC = − 0.529 × ( + 42.00 ) = − 22.22 kN ⋅ m .
Carry-over from B A BA B A to fixed end A B AB A B : − 19.78 × 0.50 = − 9.89 kN ⋅ m -19.78 \times 0.50 = -9.89\text{ kN}\cdot\text{m} − 19.78 × 0.50 = − 9.89 kN ⋅ m .
Carry-over from B C BC BC to pinned end C B CB CB : 0 0 0 (since modified stiffness 3 E I / L 3EI/L 3 E I / L was used).
Because joint B B B is balanced and no carry-overs return to B B B , the solution converges in a single distribution step !
Step 4: Final Results:
M A B = − 81.89 kN ⋅ m M_{AB} = -81.89\text{ kN}\cdot\text{m} M A B = − 81.89 kN ⋅ m (Counterclockwise on member, acts clockwise on support A A A ).
M B A = + 52.22 kN ⋅ m M_{BA} = +52.22\text{ kN}\cdot\text{m} M B A = + 52.22 kN ⋅ m (Clockwise).
M B C = − 52.22 kN ⋅ m M_{BC} = -52.22\text{ kN}\cdot\text{m} M BC = − 52.22 kN ⋅ m (Counterclockwise).
M C B = 0.00 kN ⋅ m M_{CB} = 0.00\text{ kN}\cdot\text{m} M CB = 0.00 kN ⋅ m (Pinned end).
Joint B B B equilibrium: M B A + M B C = + 52.22 − 52.22 = 0 M_{BA} + M_{BC} = +52.22 - 52.22 = 0 M B A + M BC = + 52.22 − 52.22 = 0 . (Exact equilibrium verified).
6. Licensure Exam Pitfalls & Review Notes
Warning
Pitfall 1: Overhangs and Cantilevers in Moment Distribution A cantilever overhang has zero rotational restraint against joint rotation ( K = 0 K = 0 K = 0 ). Therefore, its Distribution Factor is D F = 0 DF = 0 D F = 0 . The moment produced by loads on the cantilever is statically determinate ( M cant = − w L cant 2 / 2 M_{\text{cant}} = -w L_{\text{cant}}^2 / 2 M cant = − w L cant 2 /2 ). Treat this known moment as a fixed joint load that participates in the initial joint unbalance; never distribute moments into a cantilever overhang!
Caution
Pitfall 2: Neglecting Modified Stiffness at Exterior Pinned Supports Using standard stiffness K = 4 E I / L K = 4EI/L K = 4 E I / L at an exterior pin requires carrying over moments back and forth between the pin and the interior joint for 5 to 6 cycles before convergence. Utilizing K = 3 E I / L K = 3EI/L K = 3 E I / L with C O F = 0 COF = 0 COF = 0 achieves the exact answer in one single cycle , saving invaluable minutes during board exams.
Tip
Pitfall 3: Slope Deflection Sign Conventions Clockwise member end moments and joint rotations are positive. If an applied fixed-end moment acts counterclockwise on the beam end, enter it with a negative sign. Failure to maintain strict clockwise-positive signs in the shear equations is the single leading source of error in sway frame problems.