Study guide
15.5 Construction Materials Testing and Concrete Mix Proportioning
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
15.5 Construction Materials Testing and Concrete Mix Proportioning
Key Takeaways Explain This Topic AI
The ASTM C143 slump cone is 300 mm high with a 200 mm base and 100 mm top, filled in three layers each rodded 25 times.
The splitting tensile strength of a cylinder is T = 2P/(πLD), from ASTM C496.
Under ACI 318, cored concrete is adequate if the average of three cores is at least 0.85f′c and no single core is below 0.75f′c.
Fineness modulus is the sum of the cumulative percentages retained on the standard sieves from 150 µm upward, divided by 100.
In ACI 211.1 proportioning, the fine aggregate is the absolute volume left after water, cement, coarse aggregate and air are subtracted from 1 m³.
Last updated: October 2026
15.5 Construction Materials Testing and Concrete Mix Proportioning
PSAD area 8 of the 2022 table of specifications, "Construction Materials and Testing," has one competency worth 4% (3 items): distinguish the equipment and apparatus used to test construction materials, and proportion concrete mixes. Statistical evaluation of strength tests, with the standard deviation and required average strength f c r ′ f'_{cr} f cr ′ , is in Section 3.1. Material properties and handling are in Section 6.1.
Testing Fresh Concrete
Test Standard Apparatus and procedure
Slump ASTM C143 Metal cone 300 mm high, 200 mm base and 100 mm top diameter. Fill in three layers of equal volume, rodding each layer 25 times with a 16 mm bullet-nosed rod. Lift the cone vertically in about 5 seconds. Slump is the drop of the concrete's top center.
Sampling ASTM C172 Composite sample taken from the middle portion of the batch
Making and curing cylinders ASTM C31 150 × 300 mm cylinders in three rodded layers, or 100 × 200 mm in two, 25 strokes per layer; standard moist curing
- Air content ASTM C231 (pressure) or C173 (volumetric) Pressure meter for normal-weight concrete
- Density (unit weight) and yield ASTM C138 Measure of known volume; checks batch yield and air
- Temperature ASTM C1064 Thermometer in the fresh sample
- Testing Hardened Concrete
Test Standard Result
Compressive strength ASTM C39 f c = P / A f_c = P/A f c = P / A on cylinders in a compression machine at a controlled loading rate
Flexural strength (third-point loading) ASTM C78 Modulus of rupture R = P L / ( b d 2 ) R = PL/(bd^2) R = P L / ( b d 2 ) when fracture is in the middle third
Flexural strength (center-point loading) ASTM C293 R = 3 P L / ( 2 b d 2 ) R = 3PL/(2bd^2) R = 3 P L / ( 2 b d 2 )
- Splitting tensile strength ASTM C496 T = 2 P / ( π L D ) T = 2P/(\pi L D) T = 2 P / ( π L D )
- Drilled cores ASTM C42 Strength of in-place concrete
Rebound hammer ASTM C805 Surface hardness; used to compare and locate weak areas, not as a substitute for cores
Ultrasonic pulse velocity ASTM C597 Pulse velocity indicates uniformity, cracks and voids
Example. A 150 × 300 mm 150 \times 300\text{ mm} 150 × 300 mm cylinder fails at P = 250 kN P = 250\text{ kN} P = 250 kN in a splitting test:
T = 2 ( 250,000 ) π ( 300 ) ( 150 ) = 3.54 MPa T = \frac{2(250{,}000)}{\pi(300)(150)} = 3.54\text{ MPa} T = π ( 300 ) ( 150 ) 2 ( 250 , 000 ) = 3.54 MPa
ACI 318 Sampling and Acceptance (NSCP 2015 Chapter 4)
Strength test: the average strength of at least two 150 × 300 mm 150 \times 300\text{ mm} 150 × 300 mm cylinders or three 100 × 200 mm 100 \times 200\text{ mm} 100 × 200 mm cylinders, usually at 28 days.
Sampling frequency: at least once a day for each class of concrete, once for each 110 m 3 110\text{ m}^3 110 m 3 , and once for each 460 m 2 460\text{ m}^2 460 m 2 of slab or wall surface.
Acceptance:
every average of three consecutive strength tests is at least f c ′ f'_c f c ′ ;
no single test falls below f c ′ − 3.5 MPa f'_c - 3.5\text{ MPa} f c ′ − 3.5 MPa when f c ′ ≤ 35 MPa f'_c \le 35\text{ MPa} f c ′ ≤ 35 MPa , or below 0.90 f c ′ 0.90f'_c 0.90 f c ′ when f c ′ > 35 MPa f'_c > 35\text{ MPa} f c ′ > 35 MPa .
Low-strength investigation: take three cores for each strength test that fell more than 3.5 MPa below f c ′ f'_c f c ′ . The concrete is considered structurally adequate if:
the average of the three cores is at least 0.85 f c ′ 0.85f'_c 0.85 f c ′ ; and
no single core is below 0.75 f c ′ 0.75f'_c 0.75 f c ′ .
Example. With f c ′ = 28 MPa f'_c = 28\text{ MPa} f c ′ = 28 MPa , cores test at 24.5, 25.0 and 22.0 MPa.
The average is 23.83 ≥ 0.85 ( 28 ) = 23.8 MPa 23.83 \ge 0.85(28) = 23.8\text{ MPa} 23.83 ≥ 0.85 ( 28 ) = 23.8 MPa .
The lowest core is 22.0 ≥ 0.75 ( 28 ) = 21.0 MPa 22.0 \ge 0.75(28) = 21.0\text{ MPa} 22.0 ≥ 0.75 ( 28 ) = 21.0 MPa .
The concrete is adequate.
Testing Aggregates
- Test Standard Use
- Sieve analysis ASTM C136 (grading limits in C33) Particle-size distribution and fineness modulus
Specific gravity and absorption ASTM C127 (coarse), C128 (fine) Absolute volumes and water corrections in mix design
- Dry-rodded unit weight ASTM C29 Coarse aggregate content in ACI 211.1
- Total moisture content ASTM C566 Field batch-weight adjustments
- Los Angeles abrasion ASTM C131 (smaller sizes), C535 (larger) Resistance to wear and degradation
- Clay lumps, fines and organic impurities ASTM C142, C117, C40 Cleanliness of aggregates
Fineness modulus (FM) is the sum of the cumulative percentages retained on the 150 µm, 300 µm, 600 µm, 1.18 mm, 2.36 mm and 4.75 mm sieves, plus the larger standard sieves when present, divided by 100. ASTM C33 fine aggregate usually has an FM between 2.3 and 3.1. A higher FM means coarser sand.
Example. Cumulative retained percentages are 3 (4.75 mm), 15 (2.36 mm), 35 (1.18 mm), 58 (600 µm), 82 (300 µm) and 96 (150 µm). FM = 289 / 100 = 2.89 = 289/100 = 2.89 = 289/100 = 2.89 .
Testing Reinforcing Steel and Other Materials
Reinforcing bars are tested in a universal testing machine (UTM) for yield strength, tensile strength and elongation, and are bent around a specified pin to check ductility. Deformed bars sold in the Philippines are produced to the Philippine National Standard PNS 49, and imported bars to ASTM A615 or A706.
Concrete hollow blocks are tested for compressive strength on the net or gross area as specified.
Soils for embankments and subgrades are tested by Proctor compaction, field density (sand cone, ASTM D1556) and CBR. These are covered in Section 10.1.
Mix Proportioning by ACI 211.1 (Absolute Volume)
Choose the slump for the type of construction.
Choose the nominal maximum aggregate size (NMAS) , which must suit the member size and bar spacing.
Estimate mixing water and air content from the ACI table for that slump and NMAS.
Select the water-cement ratio for the required average strength f c r ′ f'_{cr} f cr ′ (Section 3.1) and for durability.
Compute the cement content as water ÷ (w/c).
Find the coarse aggregate content: table volume (from NMAS and sand FM) × dry-rodded unit weight.
Find the fine aggregate content: 1 m³ minus the absolute volumes of water, cement, coarse aggregate and air.
Adjust for aggregate moisture and make trial batches.
Example. The target is f c r ′ = 30 MPa f'_{cr} = 30\text{ MPa} f cr ′ = 30 MPa in non-air-entrained concrete, with slump 75–100 mm and NMAS 25 mm. The sand has FM = 2.60. The coarse aggregate has a dry-rodded unit weight of 1,600 kg/m 3 1{,}600\text{ kg/m}^3 1 , 600 kg/m 3 . Oven-dry specific gravities are 2.68 (coarse) and 2.64 (fine), and cement is 3.15.
- Step ACI 211.1 table value Result per m³
- Water, entrapped air 193 kg; 1.5% 193 kg
- w/c for 30 MPa 0.54 Cement = 193 / 0.54 = 357.4 kg = 193/0.54 = 357.4\text{ kg} = 193/0.54 = 357.4 kg
Coarse aggregate volume 0.69 0.69 × 1,600 = 1,104 kg 0.69 \times 1{,}600 = 1{,}104\text{ kg} 0.69 × 1 , 600 = 1 , 104 kg
The absolute volumes are:
- water 193 / 1,000 = 0.1930 193/1{,}000 = 0.1930 193/1 , 000 = 0.1930 ;
- cement 357.4 / 3,150 = 0.1135 357.4/3{,}150 = 0.1135 357.4/3 , 150 = 0.1135 ;
- coarse 1,104 / 2,680 = 0.4119 1{,}104/2{,}680 = 0.4119 1 , 104/2 , 680 = 0.4119 ;
air 0.0150 0.0150 0.0150 .
Their sum is 0.7334 m 3 0.7334\text{ m}^3 0.7334 m 3 . The fine aggregate is ( 1 − 0.7334 ) ( 2,640 ) = 704 kg (1 - 0.7334)(2{,}640) = 704\text{ kg} ( 1 − 0.7334 ) ( 2 , 640 ) = 704 kg .
Moisture adjustment. The sand has 4.0% total moisture with 1.0% absorption, and the gravel has 1.0% with 0.5% absorption.
Wet sand: 704 ( 1.04 ) = 732 kg 704(1.04) = 732\text{ kg} 704 ( 1.04 ) = 732 kg .
Wet gravel: 1,104 ( 1.01 ) = 1,115 kg 1{,}104(1.01) = 1{,}115\text{ kg} 1 , 104 ( 1.01 ) = 1 , 115 kg .
Batch water: 193 − 704 ( 0.030 ) − 1,104 ( 0.005 ) = 166 kg 193 - 704(0.030) - 1{,}104(0.005) = 166\text{ kg} 193 − 704 ( 0.030 ) − 1 , 104 ( 0.005 ) = 166 kg .
Philippine volumetric classes. Field estimating in the Philippines commonly uses nominal mixes by volume:
- Class AA, 1 : 1.5 : 3;
- Class A, 1 : 2 : 4;
- Class B, 1 : 2.5 : 5;
Class C, 1 : 3 : 6.
Cement factors in 40-kg bags per cubic meter come from estimating tables. These nominal mixes are for quantity estimates. Strength-controlled work is proportioned and accepted by tests as described above.