Study guide
15.2 Structural Steel Compression Members and Beam Design
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
15.2 Structural Steel Compression Members and Beam Design
Key Takeaways Explain This Topic AI
The column slenderness parameter KL/r dictates the transition between inelastic buckling (KL/r ≤ 4.71√(E/Fy)) and elastic Euler buckling (KL/r > 4.71√(E/Fy)) per NSCP 2015 Section 505 (AISC Chapter E).
For inelastic column buckling, the critical stress is Fcr = [0.658^(Fy/Fe)] Fy, whereas for elastic buckling, Fcr = 0.877 Fe, with ϕc = 0.90 and Ωc = 1.67.
The effective length factor K accounts for rotational and translational end restraints; alignment charts use joint stiffness ratios GA and GB to determine K for braced (non-sway, K ≤ 1.0) and unbraced (sway, K ≥ 1.0) frames.
Steel flexural members with adequate lateral bracing reach their full plastic moment capacity Mp = Fy Zx, with the shape factor Z/S typically ranging between 1.10 and 1.15 for wide-flange I-sections.
When the unbraced length Lb exceeds Lp, lateral-torsional buckling (LTB) limits flexural strength, modified by the moment gradient factor Cb.
Last updated: October 2026
15.2 Structural Steel Compression Members and Beam Design
Compression members and flexural beams represent the primary load-resisting elements of building frames, industrial trusses, and bridges. Unlike tension members, steel elements subjected to axial compression or bending flexure are inherently prone to instability limit states —including overall flexural buckling, torsional-flexural buckling, local plate buckling, and lateral-torsional buckling (LTB). Understanding the mathematical transition between material yielding and geometric instability is fundamental to structural steel design under NSCP 2015 Sections 505 and 506 (based on AISC 360-10 Chapters E and F).
1. Column Buckling Mechanics & Effective Length Factor ( K K K )
An ideal, perfectly straight elastic column pinned at both ends buckles at the Euler critical load ( P e P_e P e ) :
P e = π 2 E I ( K L ) 2 ⟹ F e = P e A g = π 2 E ( K L r ) 2 P_e = \frac{\pi^2 E I}{(K L)^2} \implies F_e = \frac{P_e}{A_g} = \frac{\pi^2 E}{\left( \frac{K L}{r} \right)^2} P e = ( K L ) 2 π 2 E I ⟹ F e = A g P e = ( r K L ) 2 π 2 E
Where:
E E E = modulus of elasticity of structural steel ( 200 , 000 MPa 200,000\text{ MPa} 200 , 000 MPa or 29 , 000 ksi 29,000\text{ ksi} 29 , 000 ksi ).
I I I = moment of inertia about the axis of buckling ( I = A r 2 I = A r^2 I = A r 2 ).
r r r = radius of gyration ( r = I / A r = \sqrt{I/A} r = I / A ).
L L L = actual unbraced length of the column.
K K K = effective length factor , representing the ratio of the distance between inflection points of zero moment to the actual unbraced length.
K L r \frac{K L}{r} r K L = slenderness ratio of the column.
Boundary Restraints and K K K -Values
In structural analysis, theoretical end conditions assume idealized frictionless pins or zero-rotation fixed supports. In actual construction, connection flexibility, foundation settlement, and gusset rotations prevent perfect fixity. The AISC Commentary table on effective length factors (Table C-A-7.1) gives both theoretical and recommended design K K K values:
- End Conditions Buckled Shape Theoretical K K K Recommended Design K K K
- Pinned-Pinned Half sine wave 1.0 1.0 1.0 1.0 1.0 1.0
- Fixed-Fixed Two inflection points at quarter points 0.5 0.5 0.5 0.65 0.65 0.65
- Fixed-Pinned Inflection point at 0.7 L 0.7 L 0.7 L from fixed base 0.7 0.7 0.7 0.80 0.80 0.80
- Fixed-Free (Cantilever flag pole) Quarter sine wave 2.0 2.0 2.0 2.10 2.10 2.10
- Fixed-Guided (Sidesway permitted, top rotation fixed) S-curve with translation 1.0 1.0 1.0 1.20 1.20 1.20
- Pinned-Guided (Sidesway permitted, top rotation free) Leaning mechanism 2.0 2.0 2.0 2.0 2.0 2.0
- Maximum Slenderness Limit
AISC 360 (Section E2 user note), adopted in NSCP 2015, recommends that for members designed on the basis of compression, the slenderness ratio preferably not exceed:
- K L r ≤ 200 \frac{K L}{r} \le 200 r K L ≤ 200
- 2. Alignment Charts for Frames (Sway vs. Non-Sway)
For columns in continuous building frames, end rotational restraint depends on the relative flexural stiffnesses of the columns and framing girders meeting at joints A A A and B B B . The rotational stiffness ratio ( G G G ) at a joint is defined as:
G = ∑ ( E I / L ) columns ∑ ( E I / L ) girders G = \frac{\sum (E I / L)_{\text{columns}}}{\sum (E I / L)_{\text{girders}}} G = ∑ ( E I / L ) girders ∑ ( E I / L ) columns
If a column base is pinned to the foundation, theoretical G = ∞ G = \infty G = ∞ (recommended design value G = 10 G = 10 G = 10 ).
If a column base is rigidly fixed to the foundation, theoretical G = 0 G = 0 G = 0 (recommended design value G = 1.0 G = 1.0 G = 1.0 ).
Sidesway-Inhibited (Braced / Non-Sway) Frames
In braced frames (braced by diagonal trusses, shear walls, or moment cores), lateral drift is prevented. The effective length factor K K K is always less than or equal to 1.0 1.0 1.0 ( 0.5 ≤ K ≤ 1.0 0.5 \le K \le 1.0 0.5 ≤ K ≤ 1.0 ), governed by the transcendental equation:
G A G B 4 ( π K ) 2 + ( G A + G B 2 ) ( 1 − π / K tan ( π / K ) ) + 2 ( tan ( π / 2 K ) π / K ) − 1 = 0 \frac{G_A G_B}{4} \left(\frac{\pi}{K}\right)^2 + \left(\frac{G_A + G_B}{2}\right) \left( 1 - \frac{\pi / K}{\tan(\pi / K)} \right) + 2 \left( \frac{\tan(\pi / 2K)}{\pi / K} \right) - 1 = 0 4 G A G B ( K π ) 2 + ( 2 G A + G B ) ( 1 − t a n ( π / K ) π / K ) + 2 ( π / K t a n ( π /2 K ) ) − 1 = 0
Sidesway-Uninhibited (Unbraced / Sway) Frames
In unbraced moment frames, lateral stability depends solely on the flexural rigidity of the columns and beams. Sidesway buckling can occur, meaning the effective length factor K K K is always greater than or equal to 1.0 1.0 1.0 ( 1.0 ≤ K < ∞ 1.0 \le K < \infty 1.0 ≤ K < ∞ ), governed by:
G A G B ( π / K ) 2 − 36 6 ( G A + G B ) − π / K tan ( π / K ) = 0 \frac{G_A G_B (\pi / K)^2 - 36}{6 (G_A + G_B)} - \frac{\pi / K}{\tan(\pi / K)} = 0 6 ( G A + G B ) G A G B ( π / K ) 2 − 36 − t a n ( π / K ) π / K = 0
3. AISC / NSCP 2015 Column Strength Curves
Real steel columns contain residual stresses (from differential cooling after hot-rolling or flame cutting) and initial geometric out-of-straightness (camber/sweep ≈ L / 1000 \approx L/1000 ≈ L /1000 ). Consequently, columns with intermediate slenderness yield in their outer fibers before reaching the Euler buckling load, exhibiting inelastic buckling .
Slenderness Threshold
The boundary between inelastic buckling and elastic Euler buckling occurs at:
K L r = 4.71 E F y ( equivalent to F y F e = 2.25 ) \frac{K L}{r} = 4.71 \sqrt{\frac{E}{F_y}} \qquad \left( \text{equivalent to } \frac{F_y}{F_e} = 2.25 \right) r K L = 4.71 F y E ( equivalent to F e F y = 2.25 )
For standard A36 steel ( F y = 248 MPa F_y = 248\text{ MPa} F y = 248 MPa , E = 200 , 000 MPa E = 200,000\text{ MPa} E = 200 , 000 MPa ): 4.71 200 , 000 248 = 133.7 4.71 \sqrt{\frac{200,000}{248}} = 133.7 4.71 248 200 , 000 = 133.7 .
For Grade 50 steel ( F y = 345 MPa F_y = 345\text{ MPa} F y = 345 MPa , E = 200 , 000 MPa E = 200,000\text{ MPa} E = 200 , 000 MPa ): 4.71 200 , 000 345 = 113.4 4.71 \sqrt{\frac{200,000}{345}} = 113.4 4.71 345 200 , 000 = 113.4 .
Critical Buckling Stress ( F c r F_{cr} F cr )
Inelastic Buckling Regime: When K L r ≤ 4.71 E F y \frac{K L}{r} \le 4.71 \sqrt{\frac{E}{F_y}} r K L ≤ 4.71 F y E (or F e ≥ 0.44 F y F_e \ge 0.44 F_y F e ≥ 0.44 F y ): F c r = [ 0.658 F y F e ] F y F_{cr} = \left[ 0.658^{\frac{F_y}{F_e}} \right] F_y F cr = [ 0.65 8 F e F y ] F y
Elastic Buckling Regime: When K L r > 4.71 E F y \frac{K L}{r} > 4.71 \sqrt{\frac{E}{F_y}} r K L > 4.71 F y E (or F e < 0.44 F y F_e < 0.44 F_y F e < 0.44 F y ): F c r = 0.877 F e F_{cr} = 0.877 F_e F cr = 0.877 F e (The factor 0.877 0.877 0.877 accounts for initial column out-of-straightness).
Nominal Compressive Strength
For columns with compact and non-compact cross-sections (no local buckling):
P n = F c r A g P_n = F_{cr} A_g P n = F cr A g
ϕ c P n = 0.90 F c r A g ( LRFD ) , P n Ω c = F c r A g 1.67 ( ASD ) \phi_c P_n = 0.90 F_{cr} A_g \quad (\text{LRFD}), \qquad \frac{P_n}{\Omega_c} = \frac{F_{cr} A_g}{1.67} \quad (\text{ASD}) ϕ c P n = 0.90 F cr A g ( LRFD ) , Ω c P n = 1.67 F cr A g ( ASD )
4. Local Buckling & Width-to-Thickness Limits
Before an entire column or beam reaches its overall buckling capacity, individual plate elements (flanges, webs, legs) may wrinkle or buckle locally under compressive stress. Cross-sections are classified per NSCP Section 502.4 based on their width-to-thickness ratio ( λ = b / t \lambda = b/t λ = b / t or h / t w h/t_w h / t w ):
Compact Sections: Elements can develop full plastic moment capacity ( M p M_p M p ) and undergo extensive plastic rotation without local buckling ( λ ≤ λ p \lambda \le \lambda_p λ ≤ λ p ).
Non-Compact Sections: Elements can develop the yield stress in compression before local buckling occurs, but cannot achieve full plastic rotation capacity ( λ p < λ ≤ λ r \lambda_p < \lambda \le \lambda_r λ p < λ ≤ λ r ).
Slender Sections: Elements buckle locally in the elastic range before the material yield stress is reached ( λ > λ r \lambda > \lambda_r λ > λ r ). Slender columns require a reduction factor ( Q = Q s Q a Q = Q_s Q_a Q = Q s Q a ) that scales down F c r F_{cr} F cr .
For hot-rolled I-shaped columns:
Unstiffened element (flange in compression): λ = b f 2 t f \lambda = \frac{b_f}{2 t_f} λ = 2 t f b f , λ r = 0.56 E F y \lambda_r = 0.56 \sqrt{\frac{E}{F_y}} λ r = 0.56 F y E .
Stiffened element (web in axial compression): λ = h t w \lambda = \frac{h}{t_w} λ = t w h , λ r = 1.49 E F y \lambda_r = 1.49 \sqrt{\frac{E}{F_y}} λ r = 1.49 F y E .
5. Steel Flexural Members (Beams): Plastic Moment & Shape Factor
When an I-shaped beam is subjected to bending moment about its major axis, the stress distribution progresses through three distinct stages:
Elastic Bending Stage: Stresses vary linearly from zero at the neutral axis to extreme fiber stress f b = M / S x f_b = M / S_x f b = M / S x . The yield moment ( M y M_y M y ) corresponds to first yield at the extreme fibers: M y = F y S x M_y = F_y S_x M y = F y S x where S x = I x c S_x = \frac{I_x}{c} S x = c I x is the elastic section modulus.
Inelastic Bending Stage: Outer fibers yield plastically while inner fibers remain elastic. The plastic zones propagate inward toward the neutral axis.
Fully Plastic Stage: The entire cross-section yields simultaneously in tension and compression ( f = F y f = F_y f = F y ). The neutral axis divides the section into equal areas of tension and compression ( A T = A C = A / 2 A_T = A_C = A/2 A T = A C = A /2 ). The plastic moment capacity ( M p M_p M p ) is: M p = F y Z x = F y ∑ ∣ A i y i ∣ M_p = F_y Z_x = F_y \sum |A_i y_i| M p = F y Z x = F y ∑ ∣ A i y i ∣ where Z x Z_x Z x is the plastic section modulus .
The Shape Factor
The ratio of the fully plastic moment to the elastic yield moment is defined as the Shape Factor ( S F SF SF ) :
S F = M p M y = F y Z x F y S x = Z x S x SF = \frac{M_p}{M_y} = \frac{F_y Z_x}{F_y S_x} = \frac{Z_x}{S_x} SF = M y M p = F y S x F y Z x = S x Z x
Standard Wide-Flange (W) beams: S F ≈ 1.10 to 1.15 SF \approx 1.10 \text{ to } 1.15 SF ≈ 1.10 to 1.15 (typically taken as 1.12 1.12 1.12 ).
Solid rectangular sections: S F = 1.50 SF = 1.50 SF = 1.50 .
Solid circular sections: S F = 1.70 SF = 1.70 SF = 1.70 .
Diamond sections (bending about diagonal): S F = 2.00 SF = 2.00 SF = 2.00 .
6. Lateral-Torsional Buckling (LTB) of Beams
When an I-beam bends about its major strong axis, the compression flange behaves like an unbraced column. If the compression flange lacks continuous lateral support, it tends to buckle laterally out of the plane of bending, while the tension flange remains stable. The cross-section twists simultaneously, a phenomenon termed Lateral-Torsional Buckling (LTB) .
LTB Regimes Based on Unbraced Length ( L b L_b L b )
NSCP Section 506 divides flexural behavior into three distinct zones depending on the lateral unbraced length ( L b L_b L b ) of the compression flange:
Zone 1: Plastic Yielding ( L b ≤ L p L_b \le L_p L b ≤ L p ): Full plastic moment is achieved; no LTB can occur: M n = M p = F y Z x M_n = M_p = F_y Z_x M n = M p = F y Z x Where the limiting unbraced length for full plastic strength is: L p = 1.76 r y E F y L_p = 1.76 r_y \sqrt{\frac{E}{F_y}} L p = 1.76 r y F y E
Zone 2: Inelastic LTB ( L p < L b ≤ L r L_p < L_b \le L_r L p < L b ≤ L r ): Buckling initiates after part of the compression flange has yielded: M n = C b [ M p − ( M p − 0.70 F y S x ) ( L b − L p L r − L p ) ] ≤ M p M_n = C_b \left[ M_p - (M_p - 0.70 F_y S_x) \left( \frac{L_b - L_p}{L_r - L_p} \right) \right] \le M_p M n = C b [ M p − ( M p − 0.70 F y S x ) ( L r − L p L b − L p ) ] ≤ M p
Zone 3: Elastic LTB ( L b > L r L_b > L_r L b > L r ): Buckling occurs in the purely linear elastic range: M n = F c r S x = C b π 2 E ( L b / r t s ) 2 1 + 0.078 J c S x h 0 ( L b r t s ) 2 S x ≤ M p M_n = F_{cr} S_x = C_b \frac{\pi^2 E}{(L_b / r_{ts})^2} \sqrt{1 + 0.078 \frac{J c}{S_x h_0} \left( \frac{L_b}{r_{ts}} \right)^2} S_x \le M_p M n = F cr S x = C b ( L b / r t s ) 2 π 2 E 1 + 0.078 S x h 0 J c ( r t s L b ) 2 S x ≤ M p
Moment Gradient Factor ( C b C_b C b )
The theoretical derivation of LTB assumes a uniform bending moment throughout the unbraced length (the worst-case condition, C b = 1.0 C_b = 1.0 C b = 1.0 ). When the moment varies along the unbraced length, non-uniform compression relieves buckling propensity, accounted for by the moment gradient factor ( C b C_b C b ) :
C b = 12.5 M max 2.5 M max + 3 M A + 4 M B + 3 M C R m C_b = \frac{12.5 M_{\max}}{2.5 M_{\max} + 3 M_A + 4 M_B + 3 M_C} R_m C b = 2.5 M m a x + 3 M A + 4 M B + 3 M C 12.5 M m a x R m
Where:
M max M_{\max} M m a x = absolute value of maximum moment in the unbraced segment.
M A M_A M A = absolute moment at quarter-point ( L b / 4 L_b / 4 L b /4 ).
M B M_B M B = absolute moment at mid-point ( L b / 2 L_b / 2 L b /2 ).
M C M_C M C = absolute moment at three-quarter point ( 3 L b / 4 3 L_b / 4 3 L b /4 ).
R m = 1.0 R_m = 1.0 R m = 1.0 for doubly symmetric members.
Note: In all cases, C b M n C_b M_n C b M n cannot exceed the plastic moment M p M_p M p .
7. Beam Shear Strength Design
Under NSCP 2015 Section 507, the nominal shear strength of unstiffened or stiffened webs of I-shaped members is governed by shear yielding or shear buckling:
V n = 0.60 F y A w C v V_n = 0.60 F_y A_w C_v V n = 0.60 F y A w C v
ϕ v V n = 1.00 V n ( LRFD for most hot-rolled standard shapes ) , V n Ω v = V n 1.50 ( ASD ) \phi_v V_n = 1.00 V_n \quad (\text{LRFD for most hot-rolled standard shapes}), \qquad \frac{V_n}{\Omega_v} = \frac{V_n}{1.50} \quad (\text{ASD}) ϕ v V n = 1.00 V n ( LRFD for most hot-rolled standard shapes ) , Ω v V n = 1.50 V n ( ASD )
Where:
A w = d ⋅ t w A_w = d \cdot t_w A w = d ⋅ t w is the overall web area (overall beam depth × \times × web thickness).
C v C_v C v = web shear coefficient. For virtually all standard hot-rolled W-beams satisfying h t w ≤ 2.24 E F y \frac{h}{t_w} \le 2.24 \sqrt{\frac{E}{F_y}} t w h ≤ 2.24 F y E , full shear yielding develops without shear buckling, so C v = 1.0 C_v = 1.0 C v = 1.0 and ϕ v = 1.00 \phi_v = 1.00 ϕ v = 1.00 .
8. Members Under Combined Axial Load and Bending (Beam-Columns)
The PSAD TOS item "solve for the stresses in steel beams and columns due to eccentric loads" covers members carrying axial force and moment together. Examples are columns with eccentric beam reactions, rafters, and truss chords with transverse loads.
Elastic stress check (allowable stress approach). For an axial force P P P at eccentricity e e e , the extreme fiber stresses are:
f = P A ± P e c I = P A ± M S f = \frac{P}{A} \pm \frac{P e c}{I} = \frac{P}{A} \pm \frac{M}{S} f = A P ± I P ec = A P ± S M
AISC 360 interaction (H1-1). NSCP 2015 Section 508 is based on AISC 360-10 Chapter H. With required strengths P r P_r P r , M r x M_{rx} M r x , M r y M_{ry} M ry and available strengths P c = ϕ c P n P_c = \phi_c P_n P c = ϕ c P n , M c x = ϕ b M n x M_{cx} = \phi_b M_{nx} M c x = ϕ b M n x , M c y = ϕ b M n y M_{cy} = \phi_b M_{ny} M cy = ϕ b M n y :
If P r P c ≥ 0.2 : P r P c + 8 9 ( M r x M c x + M r y M c y ) ≤ 1.0 \text{If } \frac{P_r}{P_c} \ge 0.2: \quad \frac{P_r}{P_c} + \frac{8}{9}\left( \frac{M_{rx}}{M_{cx}} + \frac{M_{ry}}{M_{cy}} \right) \le 1.0 If P c P r ≥ 0.2 : P c P r + 9 8 ( M c x M r x + M cy M ry ) ≤ 1.0
If P r P c < 0.2 : P r 2 P c + ( M r x M c x + M r y M c y ) ≤ 1.0 \text{If } \frac{P_r}{P_c} < 0.2: \quad \frac{P_r}{2 P_c} + \left( \frac{M_{rx}}{M_{cx}} + \frac{M_{ry}}{M_{cy}} \right) \le 1.0 If P c P r < 0.2 : 2 P c P r + ( M c x M r x + M cy M ry ) ≤ 1.0
The required moments must include second-order ( P P P - δ \delta δ and P P P - Δ \Delta Δ ) effects, from a second-order analysis or from amplification factors.
Example. A column has ϕ c P n = 1,237 kN \phi_c P_n = 1{,}237\text{ kN} ϕ c P n = 1 , 237 kN and ϕ b M n x = 300 kN ⋅ m \phi_b M_{nx} = 300\text{ kN}\cdot\text{m} ϕ b M n x = 300 kN ⋅ m , and carries P u = 600 kN P_u = 600\text{ kN} P u = 600 kN with M u x = 120 kN ⋅ m M_{ux} = 120\text{ kN}\cdot\text{m} M ux = 120 kN ⋅ m . Since 600 / 1,237 = 0.485 ≥ 0.2 600/1{,}237 = 0.485 \ge 0.2 600/1 , 237 = 0.485 ≥ 0.2 , use H1-1a: 0.485 + ( 8 / 9 ) ( 120 / 300 ) = 0.485 + 0.356 = 0.841 ≤ 1.0 0.485 + (8/9)(120/300) = 0.485 + 0.356 = 0.841 \le 1.0 0.485 + ( 8/9 ) ( 120/300 ) = 0.485 + 0.356 = 0.841 ≤ 1.0 . The column is adequate.
- 9. Comprehensive Worked Examples
- Worked Example 1: Compressive Strength of a W-Shape Column
Problem: A W12x50 column ( A g = 9 , 420 mm 2 A_g = 9,420\text{ mm}^2 A g = 9 , 420 mm 2 , r x = 131.6 mm r_x = 131.6\text{ mm} r x = 131.6 mm , r y = 49.8 mm r_y = 49.8\text{ mm} r y = 49.8 mm ) of A36 steel ( F y = 248 MPa F_y = 248\text{ MPa} F y = 248 MPa , E = 200 , 000 MPa E = 200,000\text{ MPa} E = 200 , 000 MPa ) has an unbraced length of L = 5.0 m L = 5.0\text{ m} L = 5.0 m . Both ends are pinned ( K x = K y = 1.0 K_x = K_y = 1.0 K x = K y = 1.0 ). Check local buckling, determine the governing slenderness ratio, and compute the design compressive strength ϕ c P n \phi_c P_n ϕ c P n (LRFD).
Solution:
Step 1: Slenderness Ratio: Buckling governs about the weak y y y -axis because r y < r x r_y < r_x r y < r x : ( K L r ) y = 1.0 × 5 , 000 mm 49.8 mm = 100.40 \left( \frac{K L}{r} \right)_y = \frac{1.0 \times 5,000\text{ mm}}{49.8\text{ mm}} = 100.40 ( r K L ) y = 49.8 mm 1.0 × 5 , 000 mm = 100.40 (Check slenderness limit: 100.40 ≤ 200 100.40 \le 200 100.40 ≤ 200 . Satisfied).
Step 2: Slenderness Threshold: 4.71 E F y = 4.71 200 , 000 248 = 133.7 4.71 \sqrt{\frac{E}{F_y}} = 4.71 \sqrt{\frac{200,000}{248}} = 133.7 4.71 F y E = 4.71 248 200 , 000 = 133.7 Since K L r = 100.40 ≤ 133.7 \frac{K L}{r} = 100.40 \le 133.7 r K L = 100.40 ≤ 133.7 , buckling is inelastic .
Step 3: Euler Elastic Buckling Stress ( F e F_e F e ): F e = π 2 E ( K L / r ) 2 = π 2 × 200 , 000 ( 100.40 ) 2 = 1 , 973 , 921 10 , 080.16 = 195.82 MPa F_e = \frac{\pi^2 E}{(K L / r)^2} = \frac{\pi^2 \times 200,000}{(100.40)^2} = \frac{1,973,921}{10,080.16} = 195.82\text{ MPa} F e = ( K L / r ) 2 π 2 E = ( 100.40 ) 2 π 2 × 200 , 000 = 10 , 080.16 1 , 973 , 921 = 195.82 MPa
Step 4: Critical Stress ( F c r F_{cr} F cr ): F y F e = 248 195.82 = 1.2665 \frac{F_y}{F_e} = \frac{248}{195.82} = 1.2665 F e F y = 195.82 248 = 1.2665 F c r = [ 0.658 F y F e ] F y = [ 0.658 1.2665 ] × 248 F_{cr} = \left[ 0.658^{\frac{F_y}{F_e}} \right] F_y = \left[ 0.658^{1.2665} \right] \times 248 F cr = [ 0.65 8 F e F y ] F y = [ 0.65 8 1.2665 ] × 248 ln ( 0.658 ) = − 0.41855 ⟹ 1.2665 × ( − 0.41855 ) = − 0.53009 ⟹ e − 0.53009 = 0.58855 \ln(0.658) = -0.41855 \implies 1.2665 \times (-0.41855) = -0.53009 \implies e^{-0.53009} = 0.58855 ln ( 0.658 ) = − 0.41855 ⟹ 1.2665 × ( − 0.41855 ) = − 0.53009 ⟹ e − 0.53009 = 0.58855 F c r = 0.58855 × 248 = 145.96 MPa F_{cr} = 0.58855 \times 248 = 145.96\text{ MPa} F cr = 0.58855 × 248 = 145.96 MPa
Step 5: Nominal and Design Compressive Strength: P n = F c r A g = 145.96 MPa × 9 , 420 mm 2 = 1 , 374 , 943 N = 1 , 374.9 kN P_n = F_{cr} A_g = 145.96\text{ MPa} \times 9,420\text{ mm}^2 = 1,374,943\text{ N} = 1,374.9\text{ kN} P n = F cr A g = 145.96 MPa × 9 , 420 mm 2 = 1 , 374 , 943 N = 1 , 374.9 kN ϕ c P n = 0.90 × 1 , 374.9 kN = 1 , 237.4 kN \phi_c P_n = 0.90 \times 1,374.9\text{ kN} = 1,237.4\text{ kN} ϕ c P n = 0.90 × 1 , 374.9 kN = 1 , 237.4 kN
Worked Example 2: Flexural Plastic Capacity & Shear of a Beam
Problem: A simply supported rolled wide-flange beam has a span of 6.0 m 6.0\text{ m} 6.0 m . The beam properties are: d = 413 mm d = 413\text{ mm} d = 413 mm , t w = 9.65 mm t_w = 9.65\text{ mm} t w = 9.65 mm , S x = 1 , 180 × 10 3 mm 3 S_x = 1,180 \times 10^3\text{ mm}^3 S x = 1 , 180 × 1 0 3 mm 3 , Z x = 1 , 340 × 10 3 mm 3 Z_x = 1,340 \times 10^3\text{ mm}^3 Z x = 1 , 340 × 1 0 3 mm 3 , F y = 345 MPa F_y = 345\text{ MPa} F y = 345 MPa (Grade 50). Full lateral bracing is provided to the compression flange ( L b = 0 L_b = 0 L b = 0 ). Calculate: (a) the yield moment M y M_y M y , (b) the plastic moment M p M_p M p , (c) the shape factor, and (d) the design shear strength ϕ v V n \phi_v V_n ϕ v V n .
Solution:
Step 1: Yield Moment: M y = F y S x = 345 MPa × ( 1 , 180 × 10 3 mm 3 ) = 407.1 × 10 6 N ⋅ mm = 407.1 kN ⋅ m M_y = F_y S_x = 345\text{ MPa} \times (1,180 \times 10^3\text{ mm}^3) = 407.1 \times 10^6\text{ N}\cdot\text{mm} = 407.1\text{ kN}\cdot\text{m} M y = F y S x = 345 MPa × ( 1 , 180 × 1 0 3 mm 3 ) = 407.1 × 1 0 6 N ⋅ mm = 407.1 kN ⋅ m
Step 2: Plastic Moment: M p = F y Z x = 345 MPa × ( 1 , 340 × 10 3 mm 3 ) = 462.3 × 10 6 N ⋅ mm = 462.3 kN ⋅ m M_p = F_y Z_x = 345\text{ MPa} \times (1,340 \times 10^3\text{ mm}^3) = 462.3 \times 10^6\text{ N}\cdot\text{mm} = 462.3\text{ kN}\cdot\text{m} M p = F y Z x = 345 MPa × ( 1 , 340 × 1 0 3 mm 3 ) = 462.3 × 1 0 6 N ⋅ mm = 462.3 kN ⋅ m
Step 3: Shape Factor: S F = M p M y = 462.3 407.1 = 1.136 SF = \frac{M_p}{M_y} = \frac{462.3}{407.1} = 1.136 SF = M y M p = 407.1 462.3 = 1.136
Step 4: Design Shear Strength: Web area A w = d ⋅ t w = 413 mm × 9.65 mm = 3 , 985.45 mm 2 A_w = d \cdot t_w = 413\text{ mm} \times 9.65\text{ mm} = 3,985.45\text{ mm}^2 A w = d ⋅ t w = 413 mm × 9.65 mm = 3 , 985.45 mm 2 .
For standard hot-rolled wide flanges with C v = 1.0 C_v = 1.0 C v = 1.0 and ϕ v = 1.00 \phi_v = 1.00 ϕ v = 1.00 : V n = 0.60 F y A w = 0.60 × 345 MPa × 3 , 985.45 mm 2 = 824 , 988 N = 825.0 kN V_n = 0.60 F_y A_w = 0.60 \times 345\text{ MPa} \times 3,985.45\text{ mm}^2 = 824,988\text{ N} = 825.0\text{ kN} V n = 0.60 F y A w = 0.60 × 345 MPa × 3 , 985.45 mm 2 = 824 , 988 N = 825.0 kN ϕ v V n = 1.00 × 825.0 kN = 825.0 kN \phi_v V_n = 1.00 \times 825.0\text{ kN} = 825.0\text{ kN} ϕ v V n = 1.00 × 825.0 kN = 825.0 kN
10. Licensure Exam Pitfalls & Review Notes
Warning
Pitfall 1: Unbraced Axis Identification Columns rarely buckle about the strong axis ( x x x -axis) unless intermediate bracing is introduced in the weak direction ( y y y -axis). Always evaluate both ( K L / r ) x (KL/r)_x ( K L / r ) x and ( K L / r ) y (KL/r)_y ( K L / r ) y ; the larger slenderness ratio always controls capacity.
Caution
Pitfall 2: Theoretical vs. Recommended K K K Values On board exams, unless a problem explicitly demands the "theoretical effective length factor," always apply the recommended design K K K values (e.g., 0.65 0.65 0.65 for fixed-fixed, 0.80 0.80 0.80 for fixed-pinned, 2.10 2.10 2.10 for fixed-free).
Tip
Pitfall 3: Capping C b M n C_b M_n C b M n by M p M_p M p A favorable moment gradient can yield C b > 1.0 C_b > 1.0 C b > 1.0 (e.g., C b = 1.32 C_b = 1.32 C b = 1.32 or higher). However, the nominal flexural capacity M n M_n M n can NEVER exceed the fully plastic moment capacity M p = F y Z x M_p = F_y Z_x M p = F y Z x .