Study guide
15.1 Structural Steel Tension Members and Connections
PRC Civil Engineer Licensure Examination CELE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Examination Overview, RA 544 & Professional Practice
1.1 CELE Structure, Format, Scoring, and 2026 Subject Order 1.2 Republic Act No. 544: The Civil Engineering Law and Board Regulations 1.3 Civil Engineering Ethics, Contracts, and Professional Practice
2 Chapter 2: Engineering Mathematics, Numerical Methods & Physics
2.1 Advanced Algebra, Progressions & Word Problems 2.2 Trigonometry and Analytical Geometry 2.3 Differential and Integral Calculus 2.4 Differential Equations and Numerical Methods 2.5 Series, Hyperbolic Functions, Multivariable Calculus, and Laplace Transforms 2.6 Numerical Methods: Linear Systems, Interpolation, Curve Fitting, and ODE Solvers 2.7 Physics for Engineers: Kinematics, Newton's Laws, Work-Energy, and Momentum
3 Chapter 3: Engineering Data Analysis & Engineering Economy
3.1 Engineering Data Analysis and Statistical Applications 3.2 Parameter Estimation, Linear Regression, Correlation, and Queuing Models 3.3 Engineering Economy: Time Value of Money and Interest Formulas 3.4 Project Evaluation, Depreciation, and Benefit-Cost Analysis
4 Chapter 4: Surveying Fundamentals, Construction Layout & Route Surveying
4.1 Errors, Corrections, and Pacing/Taping 4.2 Leveling, Earthworks, and Mass Haul Diagrams 4.3 Traverse Computations, Balancing, and Area Determinations 4.4 Route Surveying: Horizontal and Vertical Curves
5 Chapter 5: Highway & Transportation Engineering
5.1 Highway Geometric Design and Sight Distances 5.2 Traffic Engineering, Flow Fundamentals, and Pavement Design 5.3 Highway Policy, Route Location, Drainage, and Earthwork Slopes 5.4 Transportation Planning, Network Analysis, and Intermodal Systems
6 Chapter 6: Construction Materials, Methods, Management & Safety
6.1 Materials for Construction: Concrete, Formwork, Masonry, Steel, and Wood Products 6.2 Construction Equipment, Formwork, and Construction Methods 6.3 Construction Occupational Safety and Health: RA 11058 and DOLE DO 13 6.4 Construction Project Management, CPM/PERT, and Resource Scheduling 6.5 Construction Principles: Design Requirements, Project Organization, Cost Control, and Value Engineering 6.6 Quantity Surveying, Unit Cost Analysis, and Project Cost Estimates 6.7 Construction Trades and Specialties: Plumbing, Plastics, Doors and Windows, Finishes, and Electrical
7 Chapter 7: Fluid Properties, Hydrostatics & Buoyancy
7.1 Fluid Properties, Units, and Pressure Measurement 7.2 Hydrostatic Pressure on Plane and Curved Surfaces 7.3 Buoyancy, Flotation, and Accelerated Fluid Masses
8 Chapter 8: Hydrodynamics, Pipe Flow, Open Channels & Water Supply
8.1 Fluid Dynamics: Continuity and Energy Equations 8.2 Flow Measurement: Orifices, Weirs, and Venturi Meters 8.3 Fluid Flow in Pipes, Friction Losses, and Pipe Networks 8.4 Open Channel Flow, Manning's Equation, and Hydraulic Jump 8.5 Water Supply: Demand, Storage, Pumping, Distribution, and Treatment
9 Chapter 9: Soil Properties, Seepage & Stresses in Soil Mass
9.1 Soil Composition, Weight-Volume Phase Relationships 9.2 Soil Classification Systems (USCS & AASHTO) and Atterberg Limits 9.3 Soil Permeability, Seepage, Flow Nets, and Effective Stress 9.4 Stresses in Soil Mass, Stress Distribution, and Immediate and Secondary Settlement
10 Chapter 10: Consolidation, Soil Strength, Earth Pressures & Foundations
10.1 Soil Compaction and Soil Compressibility/Consolidation 10.2 Shear Strength of Soils and Mohr-Coulomb Failure Criteria 10.3 Lateral Earth Pressures (Rankine & Coulomb) and Retaining Walls 10.4 Shallow and Deep Foundation Bearing Capacity and Slope Stability
11 Chapter 11: Engineering Mechanics & Statics
11.1 Force Systems, Resultants, and Equilibrium of Rigid Bodies 11.2 Centroids, Moments of Inertia, and Friction 11.3 Cables, Trusses, and Internal Forces in Members
12 Chapter 12: Strength of Materials
12.1 Axial Stress, Strain, and Deformation 12.2 Torsion, Flanged Bolt Couplings, and Thin-Walled Pressure Vessels 12.3 Beam Stresses: Flexural and Transverse Shear 12.4 Beam Deflections, Combined Stresses, and Mohr's Circle
13 Chapter 13: Structural Analysis & NSCP Load Criteria
13.1 Indeterminate Structures: Approximate and Classical Methods 13.2 Moment Distribution Method and Slope Deflection 13.3 Influence Lines for Determinate and Indeterminate Structures 13.4 NSCP Minimum Design Loads: Dead, Live, Wind, and Earthquake
14 Chapter 14: Reinforced Concrete Design (NSCP 2015 / USD)
14.1 Ultimate Strength Design (USD) Principles and Singly Reinforced Beams 14.2 Doubly Reinforced Beams and T-Beams 14.3 Shear and Diagonal Tension, Stirrup Design, and Development Length 14.4 Reinforced Concrete Columns and Isolated Footing Design
15 Chapter 15: Steel, Timber & Prestressed Design and Materials Testing
15.1 Structural Steel Tension Members and Connections 15.2 Structural Steel Compression Members and Beam Design 15.3 Timber Design Principles, Working Stress, and Sawn Lumber Beams 15.4 Prestressed Concrete Fundamentals and Prestress Losses 15.5 Construction Materials Testing and Concrete Mix Proportioning
15.1 Structural Steel Tension Members and Connections
Key Takeaways Explain This Topic AI
Tension members are governed by three primary limit states: gross section tensile yielding (Pn = Fy Ag, ϕ = 0.90, Ω = 1.67), net section tensile rupture (Pn = Fu Ae, ϕ = 0.75, Ω = 2.00), and block shear rupture (ϕ = 0.75).
For bolted tension members, the hole width deducted for net area is dh = d_bolt + 4 mm for common bolts up to 24 mm: 2 mm standard clearance plus 2 mm damage allowance.
When bolt holes are staggered, the net width is adjusted using the Cochrane formula addition of s^2 / (4g) for each diagonal pitch-gage path.
The effective net area Ae = U An accounts for shear lag when some but not all cross-sectional elements are connected, where U = 1 - x̄/L.
Bolted bearing connections must be checked for bolt shear (Rn = Fnv Ab), tearout (Rn = 1.2 lc t Fu), and bearing (Rn = 2.4 d t Fu), while fillet weld strength is governed by the effective throat thickness te = 0.707 w.
Last updated: October 2026
15.1 Structural Steel Tension Members and Connections
Tension members are structural elements subjected to direct axial tensile forces that tend to elongate the member along its longitudinal axis. Common applications in Philippine civil engineering include truss chords and web diagonals, roof bracing systems, bridge hangers, cable stays, and sag rods for purlins. Because axial tension suppresses global flexural buckling, tension members represent the most efficient structural steel configurations. However, their design is critical because failure frequently initiates at connections where holes, weld heat-affected zones, and stress concentrations reduce cross-sectional capacity.
In the National Structural Code of the Philippines (NSCP 2015 Chapter 5, Section 504 for tension members), which is based on the AISC 360-10 Specification, tension members may be designed using either Load and Resistance Factor Design (LRFD) or Allowable Strength Design (ASD) .
1. Primary Limit States for Tension Members
A structural steel tension member must possess adequate strength to resist factored tensile loads ( P u P_u P u ) in LRFD or allowable service loads ( P a P_a P a ) in ASD across three fundamental limit states:
Tensile Yielding on the Gross Section ( A g A_g A g ): Prevents excessive plastic elongation of the member along its main unperforated body under service loads.
Tensile Rupture on the Net Effective Section ( A e A_e A e ): Prevents sudden catastrophic fracture across the reduced cross-section at bolt holes or connection ends.
Block Shear Rupture: Prevents a combined shear and tension tearout mechanism through the connection boundary.
Limit State Nominal Strength ( P n P_n P n ) LRFD Resistance Factor ( ϕ \phi ϕ ) ASD Safety Factor ( Ω \Omega Ω ) Design Strength (LRFD) Allowable Strength (ASD)
Gross Yielding P n = F y A g P_n = F_y A_g P n = F y A g ϕ t = 0.90 \phi_t = 0.90 ϕ t = 0.90 Ω t = 1.67 \Omega_t = 1.67 Ω t = 1.67 ϕ t P n = 0.90 F y A g \phi_t P_n = 0.90 F_y A_g ϕ t P n = 0.90 F y A g P n / Ω t = F y A g 1.67 P_n / \Omega_t = \frac{F_y A_g}{1.67} P n / Ω t = 1.67 F y A g
Net Rupture P n = F u A e P_n = F_u A_e P n = F u A e ϕ t = 0.75 \phi_t = 0.75 ϕ t = 0.75 Ω t = 2.00 \Omega_t = 2.00 Ω t = 2.00 ϕ t P n = 0.75 F u A e \phi_t P_n = 0.75 F_u A_e ϕ t P n = 0.75 F u A e P n / Ω t = F u A e 2.00 P_n / \Omega_t = \frac{F_u A_e}{2.00} P n / Ω t = 2.00 F u A e
Block Shear AISC Eq. J4-5 (NSCP 510.4) ϕ = 0.75 \phi = 0.75 ϕ = 0.75 Ω = 2.00 \Omega = 2.00 Ω = 2.00 ϕ R n = 0.75 R n \phi R_n = 0.75 R_n ϕ R n = 0.75 R n R n / Ω = R n 2.00 R_n / \Omega = \frac{R_n}{2.00} R n /Ω = 2.00 R n
Where:
F y F_y F y = specified minimum yield stress of the structural steel (MPa).
F u F_u F u = specified minimum tensile strength of the structural steel (MPa).
A g A_g A g = gross cross-sectional area of the member (mm²).
A e A_e A e = effective net cross-sectional area (mm²).
Slenderness Recommendation
Although tension members do not suffer from compressive buckling, excessive flexibility causes unsightly sag, wind flutter, and vibrational fatigue during transport and erection. NSCP 2015 Section 504 (AISC D1) recommends a maximum slenderness ratio of:
L r ≤ 300 \frac{L}{r} \le 300 r L ≤ 300
where L L L is the unbraced length and r r r is the minimum radius of gyration ( r = I / A r = \sqrt{I/A} r = I / A ). This limit is not mandatory for rods and cables in tension.
2. Net Area ( A n A_n A n ) and Staggered Bolt Holes
When holes are drilled or punched in a tension member, the cross-sectional area is reduced. The net area ( A n A_n A n ) is the gross cross-sectional area minus the projected area of bolt holes, plus any adjustments for staggered alignments.
Design Hole Diameter Calculation
Under AISC 360-10 Section B4.3b (adopted in NSCP 2015), the hole width deducted in tension calculations is the nominal hole plus 2 mm. For standard holes on bolts up to 24 mm, that is 4 mm larger than the nominal bolt diameter ( d b o l t d_{bolt} d b o lt ):
d h = d b o l t + 2 mm (standard fabrication clearance) + 2 mm (damage allowance) = d b o l t + 4 mm d_h = d_{bolt} + 2\text{ mm (standard fabrication clearance)} + 2\text{ mm (damage allowance)} = d_{bolt} + 4\text{ mm} d h = d b o lt + 2 mm (standard fabrication clearance) + 2 mm (damage allowance) = d b o lt + 4 mm
(For U.S. Customary units, d h = d b o l t + 1 16 ′ ′ + 1 16 ′ ′ = d b o l t + 1 8 ′ ′ d_h = d_{bolt} + \frac{1}{16}'' + \frac{1}{16}'' = d_{bolt} + \frac{1}{8}'' d h = d b o lt + 16 1 ′′ + 16 1 ′′ = d b o lt + 8 1 ′′ .)
Staggered Bolt Hole Configurations (Cochrane's Rule)
When bolt holes are staggered along adjacent gage lines, failure may occur along a straight transverse plane or along a zigzag diagonal path traversing multiple holes. To account for combined normal and shear stresses along the diagonal path, V. H. Cochrane formulated the empirical pitch-gage adjustment term s 2 4 g \frac{s^2}{4g} 4 g s 2 :
w n = w g − ∑ d h + ∑ s 2 4 g w_n = w_g - \sum d_h + \sum \frac{s^2}{4g} w n = w g − ∑ d h + ∑ 4 g s 2
A n = A g − ∑ ( d h ⋅ t ) + ∑ ( s 2 4 g ⋅ t ) A_n = A_g - \sum (d_h \cdot t) + \sum \left( \frac{s^2}{4g} \cdot t \right) A n = A g − ∑ ( d h ⋅ t ) + ∑ ( 4 g s 2 ⋅ t )
Where:
w g w_g w g = gross width of the plate or unrolled angle (mm).
t t t = thickness of the member element (mm).
s s s = longitudinal center-to-center pitch between consecutive staggered holes (mm).
g g g = transverse center-to-center gage between adjacent hole centerlines (mm).
When evaluating structural angles with holes in both legs, the angle is unfolded into an equivalent flat plate. The gross width equals the sum of the leg lengths minus the angle thickness ( w g = L 1 + L 2 − t w_g = L_1 + L_2 - t w g = L 1 + L 2 − t ). The transverse gage distance ( g g g ) between a hole in one leg and a hole in the other leg equals the sum of their distances from the outer heel minus the angle thickness ( g = g 1 + g 2 − t g = g_1 + g_2 - t g = g 1 + g 2 − t ).
3. Effective Net Area and the Shear Lag Factor ( U U U )
When an axial tensile force is transferred to a member through only some, but not all, of its cross-sectional elements (for example, a single angle connected only through one leg, or a wide-flange W-beam connected only through its flanges), the connected element carries a disproportionately high stress near the connection. The unconnected elements lag behind in developing stress. This non-uniform tensile stress distribution is called shear lag .
To account for shear lag, the net area ( A n A_n A n ) is reduced to an effective net area ( A e A_e A e ) :
A e = U A n A_e = U A_n A e = U A n
(For welded connections where tensile force is transmitted directly to all elements without bolt holes, A e = U A g A_e = U A_g A e = U A g .)
Determination of the Shear Lag Factor ( U U U )
NSCP 2015 Section 504 adopts the shear lag cases of AISC 360-10 Table D3.1:
General Case (Bolted or Welded): When tension load is transmitted to some elements by bolts or longitudinal welds: U = 1 − x ˉ L U = 1 - \frac{\bar{x}}{L} U = 1 − L x ˉ Where:
x ˉ \bar{x} x ˉ = connection eccentricity, defined as the perpendicular distance from the connection shear plane to the centroid of the cross-section resisting the load.
L L L = length of the connection along the line of force (distance between first and last bolt in a line, or length of longitudinal weld).
Plates where tension is transmitted solely by bolts: All elements connected ⟹ U = 1.0 \implies U = 1.0 ⟹ U = 1.0 .
Welded Transverse Splices: If welds are purely transverse, A e = A connected A_e = A_{\text{connected}} A e = A connected and U = 1.0 U = 1.0 U = 1.0 .
Plates with Longitudinal Welds Only:
- If L ≥ 2 w L \ge 2w L ≥ 2 w : U = 1.00 U = 1.00 U = 1.00
- If 2 w > L ≥ 1.5 w 2w > L \ge 1.5w 2 w > L ≥ 1.5 w : U = 0.87 U = 0.87 U = 0.87
If 1.5 w > L ≥ w 1.5w > L \ge w 1.5 w > L ≥ w : U = 0.75 U = 0.75 U = 0.75 (where w w w is the plate width between welds, and L L L must be at least equal to w w w ).
4. Block Shear Rupture Mechanics
Block Shear Rupture is a tearing limit state where a segment or "block" of steel rips away from the member at the connection perimeter. The failure surface consists of two perpendicular planes:
A shear plane parallel to the applied tensile force.
A tension plane perpendicular to the applied tensile force.
Governing Formula (AISC 360-10 Eq. J4-5, adopted in NSCP 2015 Section 510)
The nominal block shear rupture strength R n R_n R n is given by:
R n = 0.60 F u A n v + U b s F u A n t ≤ 0.60 F y A g v + U b s F u A n t R_n = 0.60 F_u A_{nv} + U_{bs} F_u A_{nt} \le 0.60 F_y A_{gv} + U_{bs} F_u A_{nt} R n = 0.60 F u A n v + U b s F u A n t ≤ 0.60 F y A gv + U b s F u A n t
ϕ R n = 0.75 R n ( LRFD ) , R n Ω = R n 2.00 ( ASD ) \phi R_n = 0.75 R_n \quad (\text{LRFD}), \qquad \frac{R_n}{\Omega} = \frac{R_n}{2.00} \quad (\text{ASD}) ϕ R n = 0.75 R n ( LRFD ) , Ω R n = 2.00 R n ( ASD )
Where:
A g v A_{gv} A gv = gross area subject to shear (total length of shear planes × \times × thickness).
A n v A_{nv} A n v = net area subject to shear (gross shear length minus deducted hole diameters × \times × thickness).
A n t A_{nt} A n t = net area subject to tension (gross tension width minus deducted hole diameters × \times × thickness).
0.60 F u 0.60 F_u 0.60 F u = ultimate shear rupture stress ( F v u ≈ F u / 3 ≈ 0.60 F u F_{vu} \approx F_u / \sqrt{3} \approx 0.60 F_u F vu ≈ F u / 3 ≈ 0.60 F u via von Mises yield criterion).
0.60 F y 0.60 F_y 0.60 F y = shear yield stress.
U b s U_{bs} U b s = shear lag reduction factor for block shear:
U b s = 1.0 U_{bs} = 1.0 U b s = 1.0 when the tension stress distribution across the tension plane is uniform (typical angles, gusset plates, and coped beams with a single bolt line).
U b s = 0.5 U_{bs} = 0.5 U b s = 0.5 when tension stress is non-uniform (e.g., coped beams with multiple bolt lines where inner bolts yield before outer bolts).
Important
The Block Shear Cap: Notice that the first term 0.60 F u A n v 0.60 F_u A_{nv} 0.60 F u A n v is capped by 0.60 F y A g v 0.60 F_y A_{gv} 0.60 F y A gv . The total shear resistance cannot exceed gross shear yielding because significant plastic flow along the shear line occurs before ultimate rupture across the full block.
5. Bolted Connections in Tension Systems
Bolted steel connections are categorized as either bearing-type connections or slip-critical connections .
Bearing-Type vs. Slip-Critical Connections
Bearing-Type: Bolts act as pins. Load is transferred through mechanical bearing of the bolt shank against the edge of the hole and shear across the bolt cross-section. Some initial slip of the connection occurs until bolts bear against the holes.
Slip-Critical: High-strength bolts (ASTM F3125 Grade A325 or A490) are tightened to a specified minimum clamping pretension ( T b T_b T b ). Load is transferred purely by friction developed between the mating faying surfaces. Slip-critical design is required in structures subject to fatigue, cyclic load reversal, or where slip would impair structural alignment.
Bearing-Type Limit States
For bearing connections, each bolt must satisfy bolt shear, hole bearing, and tearout:
Nominal Bolt Shear Strength ( R n R_n R n ): R n = F n v A b R_n = F_{nv} A_b R n = F n v A b Where F n v F_{nv} F n v is the nominal shear stress from NSCP Table 510.3.2 (e.g., for Group A / A325 bolts: F n v = 372 MPa F_{nv} = 372\text{ MPa} F n v = 372 MPa when threads are included in shear planes 'N', and F n v = 469 MPa F_{nv} = 469\text{ MPa} F n v = 469 MPa when threads are excluded 'X'); A b = π d b o l t 2 4 A_b = \frac{\pi d_{bolt}^2}{4} A b = 4 π d b o lt 2 is the nominal unthreaded shank area.
Bearing and Tearout at Bolt Holes: Under NSCP 2015 Section 510.3.10, the nominal strength per hole is:
When deformation around the bolt hole at service load is a design consideration: R n = 1.2 l c t F u ≤ 2.4 d b o l t t F u R_n = 1.2 l_c t F_u \le 2.4 d_{bolt} t F_u R n = 1.2 l c t F u ≤ 2.4 d b o lt t F u
When deformation around the bolt hole at service load is not a design consideration: R n = 1.5 l c t F u ≤ 3.0 d b o l t t F u R_n = 1.5 l_c t F_u \le 3.0 d_{bolt} t F_u R n = 1.5 l c t F u ≤ 3.0 d b o lt t F u Where:
l c l_c l c = clear distance in the direction of force between the edge of the hole and the edge of the adjacent hole or edge of the material (mm).
t t t = thickness of the connected material (mm).
d b o l t d_{bolt} d b o lt = nominal diameter of the bolt (mm).
The term 1.2 l c t F u 1.2 l_c t F_u 1.2 l c t F u represents the tearout limit state, while 2.4 d b o l t t F u 2.4 d_{bolt} t F_u 2.4 d b o lt t F u represents the hole bearing deformation limit state.
6. Welded Connections: Fillet Welds
Welded connections join steel components through metallurgical fusion using electric arc processes (SMAW, GMAW, FCAW, SAW). Fillet welds are the most common structural weld type due to minimal edge preparation requirements.
Fillet Weld Geometry and Throat
A standard fillet weld has a triangular cross-section with leg size w w w . The critical failure plane is the effective throat thickness ( t e t_e t e ) , defined as the shortest distance from the root of the joint to the face of the diagrammatic weld:
t e = w ⋅ cos 45 ∘ = w 2 ≈ 0.707 w t_e = w \cdot \cos 45^\circ = \frac{w}{\sqrt{2}} \approx 0.707 w t e = w ⋅ cos 4 5 ∘ = 2 w ≈ 0.707 w
Nominal Strength of Fillet Welds
The nominal shear strength of the weld metal per unit area is F n w = 0.60 F E X X F_{nw} = 0.60 F_{EXX} F n w = 0.60 F EXX , where F E X X F_{EXX} F EXX is the classification strength of the welding electrode (e.g., for E70xx electrodes, F E X X = 70 ksi ≈ 485 MPa F_{EXX} = 70\text{ ksi} \approx 485\text{ MPa} F EXX = 70 ksi ≈ 485 MPa ):
R n = F n w A w e = ( 0.60 F E X X ) ⋅ ( 0.707 w L ) R_n = F_{nw} A_{we} = (0.60 F_{EXX}) \cdot (0.707 w L) R n = F n w A w e = ( 0.60 F EXX ) ⋅ ( 0.707 w L )
ϕ R n = 0.75 R n ( LRFD ) , R n Ω = R n 2.00 ( ASD ) \phi R_n = 0.75 R_n \quad (\text{LRFD}), \qquad \frac{R_n}{\Omega} = \frac{R_n}{2.00} \quad (\text{ASD}) ϕ R n = 0.75 R n ( LRFD ) , Ω R n = 2.00 R n ( ASD )
Directional Strength Enhancement
NSCP 2015 Section 510.2.4 permits an increase in nominal fillet weld strength when the angle of loading ( θ \theta θ ) deviates from the longitudinal axis of the weld:
R n = 0.60 F E X X ( 1.0 + 0.50 sin 1.5 θ ) A w e R_n = 0.60 F_{EXX} (1.0 + 0.50 \sin^{1.5} \theta) A_{we} R n = 0.60 F EXX ( 1.0 + 0.50 sin 1.5 θ ) A w e
For a purely longitudinal weld ( θ = 0 ∘ \theta = 0^\circ θ = 0 ∘ ): 1.0 + 0.50 sin 1.5 ( 0 ∘ ) = 1.00 1.0 + 0.50 \sin^{1.5}(0^\circ) = 1.00 1.0 + 0.50 sin 1.5 ( 0 ∘ ) = 1.00 .
For a purely transverse weld ( θ = 90 ∘ \theta = 90^\circ θ = 9 0 ∘ ): 1.0 + 0.50 sin 1.5 ( 90 ∘ ) = 1.50 1.0 + 0.50 \sin^{1.5}(90^\circ) = 1.50 1.0 + 0.50 sin 1.5 ( 9 0 ∘ ) = 1.50 (a 50% increase in nominal shear capacity).
7. Eccentrically Loaded Bolt Groups (Elastic Method)
When a bracket load P P P acts at eccentricity e e e from the centroid of a bolt group, each bolt resists a direct shear and a torsional shear . The plates are assumed rigid, and the group rotates about its centroid.
Direct shear on each of n n n bolts: R d = P / n R_{d} = P/n R d = P / n , parallel to P P P .
Torsional moment: M = P e M = P e M = P e .
Torsional shear on a bolt at distance r r r from the centroid: R t = M r / ∑ r 2 R_t = M r / \sum r^2 R t = M r / ∑ r 2 , perpendicular to r r r .
Components, with ∑ r 2 = ∑ ( x 2 + y 2 ) \sum r^2 = \sum (x^2 + y^2) ∑ r 2 = ∑ ( x 2 + y 2 ) : R t x = M y / ∑ r 2 R_{tx} = M y / \sum r^2 R t x = M y / ∑ r 2 and R t y = M x / ∑ r 2 R_{ty} = M x / \sum r^2 R t y = M x / ∑ r 2 .
Combine vectorially for the most remote bolt: R = ( R t x ) 2 + ( R t y + R d ) 2 R = \sqrt{(R_{tx})^2 + (R_{ty} + R_d)^2} R = ( R t x ) 2 + ( R t y + R d ) 2 for a vertical load P P P .
Example. A vertical load P = 90 kN P = 90\text{ kN} P = 90 kN acts at e = 250 mm e = 250\text{ mm} e = 250 mm from the centroid of 6 bolts in two vertical lines 150 mm 150\text{ mm} 150 mm apart, with rows at y = − 100 , 0 , + 100 mm y = -100, 0, +100\text{ mm} y = − 100 , 0 , + 100 mm .
∑ r 2 = 6 ( 75 ) 2 + 4 ( 100 ) 2 = 33,750 + 40,000 = 73,750 mm 2 \sum r^2 = 6(75)^2 + 4(100)^2 = 33{,}750 + 40{,}000 = 73{,}750\text{ mm}^2 ∑ r 2 = 6 ( 75 ) 2 + 4 ( 100 ) 2 = 33 , 750 + 40 , 000 = 73 , 750 mm 2 .
M = 90 ( 250 ) = 22,500 kN ⋅ mm M = 90(250) = 22{,}500\text{ kN}\cdot\text{mm} M = 90 ( 250 ) = 22 , 500 kN ⋅ mm .
For a corner bolt: R t x = 22,500 ( 100 ) / 73,750 = 30.5 kN R_{tx} = 22{,}500(100)/73{,}750 = 30.5\text{ kN} R t x = 22 , 500 ( 100 ) /73 , 750 = 30.5 kN and R t y = 22,500 ( 75 ) / 73,750 = 22.9 kN R_{ty} = 22{,}500(75)/73{,}750 = 22.9\text{ kN} R t y = 22 , 500 ( 75 ) /73 , 750 = 22.9 kN .
Direct shear R d = 90 / 6 = 15.0 kN R_d = 90/6 = 15.0\text{ kN} R d = 90/6 = 15.0 kN .
R = 30.5 2 + ( 22.9 + 15.0 ) 2 = 930 + 1,436 = 48.6 kN R = \sqrt{30.5^2 + (22.9 + 15.0)^2} = \sqrt{930 + 1{,}436} = 48.6\text{ kN} R = 30. 5 2 + ( 22.9 + 15.0 ) 2 = 930 + 1 , 436 = 48.6 kN .
Each bolt must have a design shear strength ϕ R n ≥ 48.6 kN \phi R_n \ge 48.6\text{ kN} ϕ R n ≥ 48.6 kN . The elastic method is conservative compared with the AISC instantaneous-center method.
- 8. Comprehensive Worked Examples
- Worked Example 1: Staggered Tension Plate Analysis
Problem: An A36 steel plate ( F y = 248 MPa F_y = 248\text{ MPa} F y = 248 MPa , F u = 400 MPa F_u = 400\text{ MPa} F u = 400 MPa ) with dimensions 250 mm × 12 mm 250\text{ mm} \times 12\text{ mm} 250 mm × 12 mm carries an axial tensile load. The plate is connected using 20 mm 20\text{ mm} 20 mm diameter bolts arranged in two gage lines spaced 75 mm 75\text{ mm} 75 mm apart, with an edge distance of 87.5 mm 87.5\text{ mm} 87.5 mm on each side. The bolts have a staggered pitch of s = 50 mm s = 50\text{ mm} s = 50 mm . Assuming all elements are connected ( U = 1.0 U = 1.0 U = 1.0 ), compute: (a) the net width and governing net area A n A_n A n , (b) the design tensile rupture strength ϕ P n \phi P_n ϕ P n (LRFD), and (c) the design tensile yielding strength ϕ P n \phi P_n ϕ P n (LRFD).
Solution:
Step 1: Bolt Hole Diameter Deduction: d h = d b o l t + 4 mm = 20 + 4 = 24 mm d_h = d_{bolt} + 4\text{ mm} = 20 + 4 = 24\text{ mm} d h = d b o lt + 4 mm = 20 + 4 = 24 mm
Step 2: Net Width Evaluation along Potential Paths:
Path A (Straight path through 1 hole): w n 1 = w g − 1 ⋅ d h = 250 − 24 = 226 mm w_{n1} = w_g - 1 \cdot d_h = 250 - 24 = 226\text{ mm} w n 1 = w g − 1 ⋅ d h = 250 − 24 = 226 mm
Path B (Zigzag path through 2 staggered holes): w n 2 = w g − 2 ⋅ d h + s 2 4 g = 250 − 2 ( 24 ) + 50 2 4 ( 75 ) = 202 + 2500 300 = 202 + 8.33 = 210.33 mm w_{n2} = w_g - 2 \cdot d_h + \frac{s^2}{4g} = 250 - 2(24) + \frac{50^2}{4(75)} = 202 + \frac{2500}{300} = 202 + 8.33 = 210.33\text{ mm} w n 2 = w g − 2 ⋅ d h + 4 g s 2 = 250 − 2 ( 24 ) + 4 ( 75 ) 5 0 2 = 202 + 300 2500 = 202 + 8.33 = 210.33 mm The critical failure path is Path B because w n 2 < w n 1 w_{n2} < w_{n1} w n 2 < w n 1 . Governing net width w n = 210.33 mm w_n = 210.33\text{ mm} w n = 210.33 mm .
Step 3: Net Area: A n = w n ⋅ t = 210.33 mm × 12 mm = 2 , 524 mm 2 A_n = w_n \cdot t = 210.33\text{ mm} \times 12\text{ mm} = 2,524\text{ mm}^2 A n = w n ⋅ t = 210.33 mm × 12 mm = 2 , 524 mm 2 With U = 1.0 U = 1.0 U = 1.0 , A e = U A n = 2 , 524 mm 2 A_e = U A_n = 2,524\text{ mm}^2 A e = U A n = 2 , 524 mm 2 .
Step 4: Design Tensile Rupture Strength (LRFD): ϕ t P n = 0.75 ⋅ F u A e = 0.75 × 400 MPa × 2 , 524 mm 2 = 757 , 200 N = 757.2 kN \phi_t P_n = 0.75 \cdot F_u A_e = 0.75 \times 400\text{ MPa} \times 2,524\text{ mm}^2 = 757,200\text{ N} = 757.2\text{ kN} ϕ t P n = 0.75 ⋅ F u A e = 0.75 × 400 MPa × 2 , 524 mm 2 = 757 , 200 N = 757.2 kN
Step 5: Design Tensile Yielding Strength (LRFD): A g = 250 × 12 = 3 , 000 mm 2 A_g = 250 \times 12 = 3,000\text{ mm}^2 A g = 250 × 12 = 3 , 000 mm 2 ϕ t P n = 0.90 ⋅ F y A g = 0.90 × 248 MPa × 3 , 000 mm 2 = 669 , 600 N = 669.6 kN \phi_t P_n = 0.90 \cdot F_y A_g = 0.90 \times 248\text{ MPa} \times 3,000\text{ mm}^2 = 669,600\text{ N} = 669.6\text{ kN} ϕ t P n = 0.90 ⋅ F y A g = 0.90 × 248 MPa × 3 , 000 mm 2 = 669 , 600 N = 669.6 kN Conclusion: The design strength of the member in LRFD is governed by gross section yielding: ϕ P n = 669.6 kN \phi P_n = 669.6\text{ kN} ϕ P n = 669.6 kN .
Worked Example 2: Block Shear Rupture of a Gusset Plate
Problem: A 10 mm 10\text{ mm} 10 mm thick gusset plate of A36 steel ( F y = 248 MPa F_y = 248\text{ MPa} F y = 248 MPa , F u = 400 MPa F_u = 400\text{ MPa} F u = 400 MPa ) connects a tension truss diagonal using a single line of four 22 mm 22\text{ mm} 22 mm diameter bolts ( d h = 26 mm d_h = 26\text{ mm} d h = 26 mm ). The bolt pitch is 75 mm 75\text{ mm} 75 mm , and the end distance along the line of load is 40 mm 40\text{ mm} 40 mm . The edge distance perpendicular to load is 40 mm 40\text{ mm} 40 mm . Tensile stress distribution is uniform ( U b s = 1.0 U_{bs} = 1.0 U b s = 1.0 ). Calculate the nominal and design block shear rupture strength (LRFD).
Solution:
Step 1: Calculate Geometric Areas:
Total length of shear line = 3 × 75 mm + 40 mm = 265 mm 3 \times 75\text{ mm} + 40\text{ mm} = 265\text{ mm} 3 × 75 mm + 40 mm = 265 mm .
A g v = 265 mm × 10 mm = 2 , 650 mm 2 A_{gv} = 265\text{ mm} \times 10\text{ mm} = 2,650\text{ mm}^2 A gv = 265 mm × 10 mm = 2 , 650 mm 2 .
Net shear length = 265 − 3.5 ( d h ) = 265 − 3.5 ( 26 ) = 265 − 91 = 174 mm 265 - 3.5(d_h) = 265 - 3.5(26) = 265 - 91 = 174\text{ mm} 265 − 3.5 ( d h ) = 265 − 3.5 ( 26 ) = 265 − 91 = 174 mm .
A n v = 174 mm × 10 mm = 1 , 740 mm 2 A_{nv} = 174\text{ mm} \times 10\text{ mm} = 1,740\text{ mm}^2 A n v = 174 mm × 10 mm = 1 , 740 mm 2 .
Gross tension length = 40 mm 40\text{ mm} 40 mm .
Net tension length = 40 − 0.5 ( d h ) = 40 − 0.5 ( 26 ) = 27 mm 40 - 0.5(d_h) = 40 - 0.5(26) = 27\text{ mm} 40 − 0.5 ( d h ) = 40 − 0.5 ( 26 ) = 27 mm .
A n t = 27 mm × 10 mm = 270 mm 2 A_{nt} = 27\text{ mm} \times 10\text{ mm} = 270\text{ mm}^2 A n t = 27 mm × 10 mm = 270 mm 2 .
Step 2: Evaluate Block Shear Equation Terms:
Rupture Term: 0.60 F u A n v + U b s F u A n t = 0.60 ( 400 ) ( 1 , 740 ) + ( 1.0 ) ( 400 ) ( 270 ) = 417 , 600 + 108 , 000 = 525 , 600 N = 525.6 kN 0.60 F_u A_{nv} + U_{bs} F_u A_{nt} = 0.60(400)(1,740) + (1.0)(400)(270) = 417,600 + 108,000 = 525,600\text{ N} = 525.6\text{ kN} 0.60 F u A n v + U b s F u A n t = 0.60 ( 400 ) ( 1 , 740 ) + ( 1.0 ) ( 400 ) ( 270 ) = 417 , 600 + 108 , 000 = 525 , 600 N = 525.6 kN .
Yield Cap: 0.60 F y A g v + U b s F u A n t = 0.60 ( 248 ) ( 2 , 650 ) + ( 1.0 ) ( 400 ) ( 270 ) = 394 , 320 + 108 , 000 = 502 , 320 N = 502.32 kN 0.60 F_y A_{gv} + U_{bs} F_u A_{nt} = 0.60(248)(2,650) + (1.0)(400)(270) = 394,320 + 108,000 = 502,320\text{ N} = 502.32\text{ kN} 0.60 F y A gv + U b s F u A n t = 0.60 ( 248 ) ( 2 , 650 ) + ( 1.0 ) ( 400 ) ( 270 ) = 394 , 320 + 108 , 000 = 502 , 320 N = 502.32 kN .
Governing Nominal Strength: Since 525.6 kN > 502.32 kN 525.6\text{ kN} > 502.32\text{ kN} 525.6 kN > 502.32 kN , the upper yield cap governs: R n = 502.32 kN R_n = 502.32\text{ kN} R n = 502.32 kN .
Step 3: Design Strength (LRFD): ϕ R n = 0.75 × 502.32 kN = 376.74 kN \phi R_n = 0.75 \times 502.32\text{ kN} = 376.74\text{ kN} ϕ R n = 0.75 × 502.32 kN = 376.74 kN
9. Licensure Exam Pitfalls & Review Notes
Warning
Pitfall 1: Bolt Hole Deduction Diameter Always add 4 mm 4\text{ mm} 4 mm (or 1 / 8 in 1/8\text{ in} 1/8 in ) to the nominal bolt diameter, not just the 2 mm 2\text{ mm} 2 mm standard clearance. The additional 2 mm 2\text{ mm} 2 mm accounts for edge damage caused by punching or thermal cutting (AISC B4.3b).
Caution
Pitfall 2: Neglecting the Block Shear Yield Cap Many candidates calculate only 0.60 F u A n v + U b s F u A n t 0.60 F_u A_{nv} + U_{bs} F_u A_{nt} 0.60 F u A n v + U b s F u A n t and forget to check whether it exceeds the yield cap 0.60 F y A g v + U b s F u A n t 0.60 F_y A_{gv} + U_{bs} F_u A_{nt} 0.60 F y A gv + U b s F u A n t . On Philippine board exams, questions are frequently crafted such that the yield cap controls.
Tip
Pitfall 3: Transverse Weld Strength Bonus When comparing welds, remember that transverse fillet welds are 50 % 50\% 50% stronger than longitudinal welds of identical size ( 1.0 + 0.50 sin 1.5 90 ∘ = 1.50 1.0 + 0.50 \sin^{1.5} 90^\circ = 1.50 1.0 + 0.50 sin 1.5 9 0 ∘ = 1.50 ), but they possess lower ductility before rupture.