Study guide

12.2 Panelboards & Switchboards

PRC Registered Master Electrician RME

Track your progress as you read

Finished sections get a check mark.

1 Introduction

RME Licensure Examination Overview & RA 7920 Framework How to Use This Study Guide & Build Your Study Plan

2 Chapter 1: DC & AC Circuit Fundamentals

1.1 Ohm's Law & DC Circuit Calculations 1.2 Kirchhoff's Laws & Series-Parallel Network Analysis 1.3 AC Fundamentals: Sine Waves, RMS & Phase Relationships 1.4 AC Circuit Impedance, Reactance & Resonance

3 Chapter 2: AC Power, Three-Phase Systems & DC Generators

2.1 Power in AC Circuits & Power Factor 2.2 Three-Phase Systems: Wye-Delta Configurations & Calculations 2.3 DC Generators: Construction, Types & Characteristics

4 Chapter 3: DC & AC Motors and Starting Methods

3.1 DC Motors: Construction, Types & Speed Control 3.2 AC Induction Motors: Construction, Slip & Synchronous Speed 3.3 Induction Motor Starting Methods

5 Chapter 4: Synchronous Machines & Transformers

4.1 Synchronous Motors & AC Generators (Alternators) 4.2 Transformers: Construction, Turns Ratio & Types 4.3 Transformer Losses, Efficiency, Cooling & Connections

6 Chapter 5: Motor Starters, Control Circuits & Overcurrent Devices

5.1 Motor Starters: DOL, Star-Delta & Autotransformer Starting 5.2 Motor Control Circuits & Overload Protection 5.3 Fuses & Circuit Breakers: Types, Ratings & Applications

7 Chapter 6: Control Devices & Electrical Components

6.1 Contactors, Relays & Other Control Devices 6.2 Electrical Components: Capacitors, Inductors & Resistors 6.3 Semiconductor Devices & Basic Solid-State Components

8 Chapter 7: Maintenance, Test Equipment & RA 7920 Law

7.1 Maintenance & Troubleshooting Practices 7.2 Test Equipment & Electrical Instruments 7.3 RA 7920: RME Law, Scope of Practice & PRC Regulation

9 Chapter 8: PEC Foundations: Scope & General Requirements

8.1 PEC Scope, Definitions & Code Organization (Part 1 vs Part 2) 8.2 General Installation Requirements & Working Space 8.3 Conductor Sizing, Ampacity & Derating 8.4 Overcurrent Protection & Conductor Protection Coordination

10 Chapter 9: Load Calculations & Wiring Methods

9.1 Voltage Drop & Continuous Load Calculations 9.2 Feeders, Load Calculations & Demand Factors 9.3 Wiring Methods: Raceways & Conduit Systems

11 Chapter 10: Cable Systems, Boxes & Wiring Devices

10.1 Wiring Methods: Cable Systems & Flexible Wiring 10.2 Boxes, Enclosures & Fittings 10.3 Wiring Devices, Receptacles & GFCI Protection

12 Chapter 11: Branch Circuits & Services

11.1 Branch Circuits & Multiwire Branch Circuits 11.2 Services & Service Equipment 11.3 Grounding: System & Equipment Grounding

13 Chapter 12: Bonding, Panelboards & Motor Wiring

12.1 Bonding & Grounding Electrode Systems 12.2 Panelboards & Switchboards 12.3 Motor & Generator Wiring, Protection & Disconnects

14 Chapter 13: Motor-Starter Diagrams & Hazardous Locations

13.1 Motor-Starter Wiring Diagrams & Control Symbols 13.2 One-Line Diagrams, Drawing Symbols & Wiring Plans 13.3 Hazardous (Classified) Locations

15 Chapter 14: Special Occupancies, Conditions & Safety

14.1 Special Occupancies (Wet/Damp Locations, Underground Wiring) 14.2 Special Conditions: Emergency Systems & Communications Wiring 14.3 Electrical Safety, PPE & Code-Mandated Working Clearances

16 Chapter 15: Final Review & Next Steps

15.1 RME Exam Strategy, Time Management & Test-Day Tips 15.2 After Passing: PRC Registration, CPD Renewal & Career Paths

12.2 Panelboards & Switchboards

Key Takeaways Explain This Topic AI

A panelboard is a smaller, usually front-accessible assembly for branch-circuit or moderate power distribution; a switchboard is a larger, often front-and-rear-accessible assembly typically used at services and heavy distribution points.

A panelboard must never be protected by an overcurrent device rated higher than its own bus assembly ampacity.

'Spaces' (physical bus positions) and 'circuits' (individual protected poles) are not the same thing -- twin breakers let multiple circuits share one space.

Working space and dedicated equipment space are separate clearance concepts: working space is the clear floor area needed to safely operate the equipment, while dedicated equipment space is the vertical zone reserved above and below it that must stay free of foreign systems.

Series-rated combinations are only valid for the specific tested and labeled device pairing and must be field-marked; they are not interchangeable with any two devices carrying the right individual ratings.

Last updated: July 2026

12.2 Panelboards & Switchboards

Distribution equipment is where an RME's design and inspection judgment gets tested in the field every day. The exam expects you to know not just what a panelboard or switchboard is, but how its ratings, its required clearances, and its labeling all interact to keep an installation safe and inspectable.

Panelboard vs. Switchboard: The Core Distinction

Both are assemblies that house overcurrent protective devices and distribute power to branch circuits or feeders, but they differ in scale, construction, and accessibility.

Feature Panelboard Switchboard

Typical mounting Wall-mounted (surface or flush) or small freestanding cabinet Large freestanding, floor-mounted assembly

Accessibility Usually front-accessible only Often front and rear (or all-sides) accessible for maintenance

Typical role Lighting/appliance branch-circuit distribution, or smaller power distribution Service entrance equipment, main switching, heavier feeder distribution

Typical capacity Modest bus ratings, commonly up to a few hundred amps Can house very large bus ratings across multiple vertical sections

Enclosure Single dead-front cabinet Multi-section, often with separate metering, main, and distribution sections

A lighting and appliance branch-circuit panelboard is a panelboard where more than a small fraction of its overcurrent devices supply lighting and appliance branch circuits, as opposed to a power panelboard , which is mostly feeder breakers. That distinction matters because lighting and appliance panelboards carry a hard cap on the number of overcurrent devices they may contain -- commonly limited to a maximum in the neighborhood of 42 single-pole equivalent positions -- while power panelboards are not subject to that same pole-count ceiling.

Panelboard Ratings

Every panelboard nameplate carries several ratings an RME must cross-check against the job:

Voltage rating -- must match, or exceed, the system voltage applied, for example 240V single-phase 3-wire versus 208Y/120V three-phase 4-wire.

Main bus ampacity -- the maximum current the internal bus bar is rated to carry continuously, independent of how the panel is fed.

Number of circuits/spaces vs. circuits -- a 'space' is a physical mounting position on the bus for a device; a 'circuit' is each individual overcurrent-protected pole. A panelboard described as providing 30 circuits within 20 physical spaces means some of those spaces hold twin breakers, with two single-pole circuits stacked into one space. Confusing spaces with circuits is a common source of undersized-panel mistakes when adding loads.

Overcurrent Protection for the Panelboard Itself

A panelboard must be protected by an overcurrent device rated no higher than the panelboard's own bus assembly rating, with a narrow exception for the specific case of a main-lug-only panel fed by a single set of service conductors already sized to the service disconnect, where the service overcurrent device itself provides that protection. In practice: if the panel's bus is rated 100A, you cannot feed it from a 150A breaker just because a customer wants extra capacity -- the panel itself becomes the weak link in a fault.

Working Space and Dedicated Equipment Space

Two separate clearance concepts govern the area around panelboards and switchboards, and RMEs are tested on both.

Working space is the clear floor area in front of the equipment that a worker needs to safely operate, inspect, or service it without contorting around obstacles or risking contact with energized parts. It is generally described by three dimensions -- depth, width, and height -- and the required depth grows with voltage and with how exposed live parts are:

  • Condition Typical Minimum Clear Depth
  • Exposed live parts on one side only, grounded parts on the other, lower voltage approximately 900 mm (3 ft)
  • Exposed live parts on one side, the other side neither grounded nor guarded approximately 1.0 m (3.5 ft)
  • Exposed live parts on both sides of the working space approximately 1.2 m (4 ft)

Width must be at least 750 mm (30 in) or the width of the equipment, whichever is greater, and the space must be clear from the floor up to roughly 2.0 m (6.5 ft) or the height of the equipment. These are conceptual, typical figures for exam purposes -- always verify against the current adopted table for the exact condition and voltage class in play.

Dedicated equipment space is a separate, vertical zone reserved above and below the panel or switchboard, typically extending from the floor to a height around 1.8 m (6 ft) above the equipment, or to a structural ceiling if lower. Foreign systems -- plumbing, ductwork, sprinkler piping not protecting the electrical space itself -- are not permitted to run through that dedicated zone, because a leak or failure there would drip or fall directly onto energized equipment.

Circuit Directory and Labeling

Every panelboard must carry a legible, durable circuit directory identifying the load served by each circuit, mounted at or near the panel where it can be read without removing the dead front. 'Outlets' or 'misc.' is not an adequate description; the directory must be specific enough, for example 'Kitchen Receptacles' or 'HVAC Condenser', that anyone servicing the panel, or shutting off power in an emergency, can identify the right breaker. Any time circuits are added, removed, or reassigned, the directory must be updated to match; a stale directory is a routine inspection citation.

Series-Rated vs. Fully-Rated Systems

At a conceptual level:

A fully rated system uses overcurrent devices that are each individually rated to interrupt the full available fault current at their point of installation.

A series-rated system uses a tested and labeled combination where an upstream device with a higher interrupting rating is allowed to protect a downstream device whose individual interrupting rating is lower than the available fault current, because the pair was tested together and shown to work safely as a combination. Series ratings are only valid for the specific tested combination -- an RME cannot mix and match breaker brands or models and assume it works -- and the equipment must be field-marked to show it is part of a series-rated system.

RME Scenarios

Adding a subpanel or feeder. Before pulling a feeder to a new subpanel, confirm the source panel has enough spare bus capacity and physical spaces, not just spaces but actual unused circuit positions, and confirm the subpanel's own bus rating exceeds the overcurrent device that will feed it.

Verifying a panel isn't overloaded or over-fused. Compare the installed main breaker, or feeder overcurrent device, rating against the bus nameplate rating -- if someone has swapped in a larger main breaker over the years to 'solve' a nuisance-tripping complaint, that panel is now over-fused relative to its bus rating and must be corrected.

Maintaining clear working space. A water heater, storage shelving, or furniture placed directly in front of an electrical panel is one of the most common field violations an RME encounters; the fix is relocating the obstruction, not documenting an exception.