Study guide
11.2 Services & Service Equipment
PRC Registered Master Electrician RME
Track your progress as you read
Finished sections get a check mark.
1 Introduction
RME Licensure Examination Overview & RA 7920 Framework How to Use This Study Guide & Build Your Study Plan
2 Chapter 1: DC & AC Circuit Fundamentals
1.1 Ohm's Law & DC Circuit Calculations 1.2 Kirchhoff's Laws & Series-Parallel Network Analysis 1.3 AC Fundamentals: Sine Waves, RMS & Phase Relationships 1.4 AC Circuit Impedance, Reactance & Resonance
3 Chapter 2: AC Power, Three-Phase Systems & DC Generators
2.1 Power in AC Circuits & Power Factor 2.2 Three-Phase Systems: Wye-Delta Configurations & Calculations 2.3 DC Generators: Construction, Types & Characteristics
4 Chapter 3: DC & AC Motors and Starting Methods
3.1 DC Motors: Construction, Types & Speed Control 3.2 AC Induction Motors: Construction, Slip & Synchronous Speed 3.3 Induction Motor Starting Methods
5 Chapter 4: Synchronous Machines & Transformers
4.1 Synchronous Motors & AC Generators (Alternators) 4.2 Transformers: Construction, Turns Ratio & Types 4.3 Transformer Losses, Efficiency, Cooling & Connections
6 Chapter 5: Motor Starters, Control Circuits & Overcurrent Devices
5.1 Motor Starters: DOL, Star-Delta & Autotransformer Starting 5.2 Motor Control Circuits & Overload Protection 5.3 Fuses & Circuit Breakers: Types, Ratings & Applications
7 Chapter 6: Control Devices & Electrical Components
6.1 Contactors, Relays & Other Control Devices 6.2 Electrical Components: Capacitors, Inductors & Resistors 6.3 Semiconductor Devices & Basic Solid-State Components
8 Chapter 7: Maintenance, Test Equipment & RA 7920 Law
7.1 Maintenance & Troubleshooting Practices 7.2 Test Equipment & Electrical Instruments 7.3 RA 7920: RME Law, Scope of Practice & PRC Regulation
9 Chapter 8: PEC Foundations: Scope & General Requirements
8.1 PEC Scope, Definitions & Code Organization (Part 1 vs Part 2) 8.2 General Installation Requirements & Working Space 8.3 Conductor Sizing, Ampacity & Derating 8.4 Overcurrent Protection & Conductor Protection Coordination
10 Chapter 9: Load Calculations & Wiring Methods
9.1 Voltage Drop & Continuous Load Calculations 9.2 Feeders, Load Calculations & Demand Factors 9.3 Wiring Methods: Raceways & Conduit Systems
11 Chapter 10: Cable Systems, Boxes & Wiring Devices
10.1 Wiring Methods: Cable Systems & Flexible Wiring 10.2 Boxes, Enclosures & Fittings 10.3 Wiring Devices, Receptacles & GFCI Protection
12 Chapter 11: Branch Circuits & Services
11.1 Branch Circuits & Multiwire Branch Circuits 11.2 Services & Service Equipment 11.3 Grounding: System & Equipment Grounding
13 Chapter 12: Bonding, Panelboards & Motor Wiring
12.1 Bonding & Grounding Electrode Systems 12.2 Panelboards & Switchboards 12.3 Motor & Generator Wiring, Protection & Disconnects
14 Chapter 13: Motor-Starter Diagrams & Hazardous Locations
13.1 Motor-Starter Wiring Diagrams & Control Symbols 13.2 One-Line Diagrams, Drawing Symbols & Wiring Plans 13.3 Hazardous (Classified) Locations
15 Chapter 14: Special Occupancies, Conditions & Safety
14.1 Special Occupancies (Wet/Damp Locations, Underground Wiring) 14.2 Special Conditions: Emergency Systems & Communications Wiring 14.3 Electrical Safety, PPE & Code-Mandated Working Clearances
16 Chapter 15: Final Review & Next Steps
15.1 RME Exam Strategy, Time Management & Test-Day Tips 15.2 After Passing: PRC Registration, CPD Renewal & Career Paths
11.2 Services & Service Equipment
Key Takeaways Explain This Topic AI
A service is the conductors and equipment that deliver energy from the utility's serving point to the premises wiring; it begins at the service point and ends at the service disconnecting means.
Overhead service drops and underground service laterals are the two ways utility conductors reach a structure, each with its own clearance, support, and protection requirements.
As a general rule, a building is supplied by only one service; recognized exceptions include fire pumps, emergency/standby systems, and multiple-occupancy buildings designed for separate utility connections.
PEC permits grouping the service disconnecting means into a limited number of individual switches or breakers — commonly up to six — provided they are grouped in one location and each is marked as to the load it serves.
Service clearances from grade, from openings such as windows and balconies, and from swimming pools exist because service conductors are continuously energized from the utility side and are not yet protected by any building overcurrent device.
Last updated: July 2026
11.2 Services & Service Equipment
What Is a "Service"?
A service is the set of conductors and equipment that deliver electrical energy from the serving utility — Meralco or a local electric cooperative, depending on the franchise area — to the wiring system of the premises being served. A service begins at the service point , the point of connection between the utility's facilities and the premises conductors, and ends at the service disconnecting means , the first point in the building where the entire electrical system can be shut off. Everything downstream of the service disconnect is feeder and branch-circuit wiring, covered under the rules discussed in the previous section; everything the RME does at the service itself — sizing, clearances, disconnect count, grounding — is governed by its own set of provisions because a mistake here affects the whole building at once, not just one circuit.
Service Drop vs. Service Lateral
Utility conductors reach a structure by one of two physical routes:
Method Description Common Use
Service drop Overhead conductors from the utility's last pole or support to the point of attachment on the structure Provincial and subdivision residential work; lower installed cost
Service lateral Underground conductors from the utility's transformer or underground main to the first point of connection at the building Dense urban CBDs, planned subdivisions, and locations where overhead lines are undesirable
A service drop requires an adequate point of attachment — often a service mast, discussed below — and must clear the ground, driveways, and building openings by set margins. A service lateral trades those overhead concerns for underground ones: conduit or cable must be protected from physical damage, buried at adequate depth, and terminated so moisture cannot track into the service equipment.
Service-Entrance Conductors
Service-entrance conductors run from the service point (or, for a lateral, from the underground termination) to the service disconnecting means. Their ampacity must never be less than the rating of the service disconnect they feed, and their size is derived from the building's calculated demand load — never simply guessed from the size of the existing wire being replaced.
Worked example. A dwelling unit has a calculated demand load of 9,200 VA at 230 V single-phase.
- Calculated load current = 9,200 VA ÷ 230 V = 40 A
- The next standard overcurrent device size at or above 40 A is 50 A — that becomes the main breaker rating
From the branch-circuit conductor table in the previous section, 14 mm² copper THHN supports roughly 55 A, comfortably covering the 50 A main, so 14 mm² is the minimum acceptable service-entrance conductor size for this dwelling
This calculate-then-round-up-then-verify-conductor sequence is the core competency the RME exam is testing when it asks about "minimum service size" — it is never a single table lookup, but a short chain of three steps.
Number of Services per Building
The general rule is that a building or structure is supplied by only one service . Multiple services complicate fault-current coordination, make it harder to fully de-energize a structure in an emergency, and confuse metering and billing. PEC recognizes a short list of situations where more than one service is allowed, including:
- Fire pumps , which must remain powered independently of the building's normal service
- Emergency and legally required standby systems that need a separate, reliably available source
Multiple-occupancy buildings specifically designed for separate utility connections — for example, a commercial strip with individually metered tenant units, or a townhouse row where each unit is intended to have its own utility account
Buildings whose calculated load exceeds what a single service of practical size can carry
An RME should treat these as narrow, code-recognized exceptions, not as license to run a second service purely for owner convenience.
Service Equipment Components
Service equipment is made up of three functional pieces, whether housed in one combination enclosure or several adjacent enclosures:
Main disconnecting means — the main breaker or switch that can open all ungrounded service conductors at once; it must be readily accessible and clearly marked as suitable for use as service equipment.
Metering equipment — the utility's revenue meter and meter base/socket, positioned per the local utility's metering rules, ahead of or integrated with the main disconnect.
Main overcurrent device — sized to the calculated demand load and coordinated with the ampacity of the service-entrance conductors, as worked through above.
Number of Disconnects at a Service
Rather than requiring a single main breaker in every case, PEC allows the service disconnecting means to be made up of up to six individual disconnects — switches or circuit breakers — provided they are all grouped at one location and each one is permanently marked to identify the load it serves. This is common in small commercial buildings: instead of one large main breaker feeding a distribution panel, the service can terminate directly into as many as six smaller breakers, each dedicated to one tenant space, one HVAC unit, or one major load, as long as the grouping does not exceed the six-disconnect limit and all of them are installed together at one location.
Service Clearances
Clearance rules exist because service conductors, unlike branch-circuit and feeder conductors, are not fused or protected until they reach the service disconnect — they are energized continuously from the utility side. Three clearance zones matter most for an RME:
Vertical clearance above grade — service-drop conductors must clear finished grade, sidewalks, and especially vehicular areas such as driveways and roads by a greater margin than they need over purely pedestrian areas, because the risk of contact from a raised vehicle or equipment is higher.
Clearance from windows, doors, porches, and balconies — conductors must be kept out of reach from any opening a person could lean or reach through, so ordinary building use never puts an occupant within reach of an unprotected, always-energized conductor.
Clearance from swimming pools — overhead service conductors need generous horizontal and vertical clearance from pool edges, diving structures, and any elevated pool deck, because people around pools routinely handle long metal or wet objects, such as skimmer poles, that can bridge an otherwise-safe distance.
Service Mast
Where roof height or obstructions require raising the point of attachment above the roofline, RMEs use a service mast — a rigid raceway extended upward to create an adequate attachment point for the service drop. Because the utility's conductors physically pull on the mast, it must have real mechanical strength — rigid steel conduit rather than thin-wall tubing — plus adequate bracing or guying back to the structure so the point of attachment cannot bend, twist, or pull loose under wind or storm loading.
RME Field Scenarios
Upgrading an old fused service. A common renovation job is replacing an aging 30 A fused residential service — rewireable fuses in an old panel board — with a modern 60 A circuit-breaker main. The RME does not simply swap the enclosure: the calculated demand load is recalculated first, since the household likely added air-conditioning, an electric water heater, or other loads since the original installation; the service-entrance conductor ampacity is verified against the new breaker rating; the grounding electrode system is checked against current requirements; and the overhead clearance at the existing point of attachment is reconfirmed if the mast or attachment height was not changed.
Small commercial strip. Five tenant units sharing one utility transformer can be designed either as one larger service with tenant sub-metering fed from a downstream distribution panel, or — where the six-disconnect grouping rule is satisfied — as up to six grouped disconnects at the service itself, each sized to its own tenant's calculated load. The choice affects both first cost and how independently the tenants can be isolated from one another electrically.