Study guide

6.3 Semiconductor Devices & Basic Solid-State Components

PRC Registered Master Electrician RME

Track your progress as you read

Finished sections get a check mark.

1 Introduction

RME Licensure Examination Overview & RA 7920 Framework How to Use This Study Guide & Build Your Study Plan

2 Chapter 1: DC & AC Circuit Fundamentals

1.1 Ohm's Law & DC Circuit Calculations 1.2 Kirchhoff's Laws & Series-Parallel Network Analysis 1.3 AC Fundamentals: Sine Waves, RMS & Phase Relationships 1.4 AC Circuit Impedance, Reactance & Resonance

3 Chapter 2: AC Power, Three-Phase Systems & DC Generators

2.1 Power in AC Circuits & Power Factor 2.2 Three-Phase Systems: Wye-Delta Configurations & Calculations 2.3 DC Generators: Construction, Types & Characteristics

4 Chapter 3: DC & AC Motors and Starting Methods

3.1 DC Motors: Construction, Types & Speed Control 3.2 AC Induction Motors: Construction, Slip & Synchronous Speed 3.3 Induction Motor Starting Methods

5 Chapter 4: Synchronous Machines & Transformers

4.1 Synchronous Motors & AC Generators (Alternators) 4.2 Transformers: Construction, Turns Ratio & Types 4.3 Transformer Losses, Efficiency, Cooling & Connections

6 Chapter 5: Motor Starters, Control Circuits & Overcurrent Devices

5.1 Motor Starters: DOL, Star-Delta & Autotransformer Starting 5.2 Motor Control Circuits & Overload Protection 5.3 Fuses & Circuit Breakers: Types, Ratings & Applications

7 Chapter 6: Control Devices & Electrical Components

6.1 Contactors, Relays & Other Control Devices 6.2 Electrical Components: Capacitors, Inductors & Resistors 6.3 Semiconductor Devices & Basic Solid-State Components

8 Chapter 7: Maintenance, Test Equipment & RA 7920 Law

7.1 Maintenance & Troubleshooting Practices 7.2 Test Equipment & Electrical Instruments 7.3 RA 7920: RME Law, Scope of Practice & PRC Regulation

9 Chapter 8: PEC Foundations: Scope & General Requirements

8.1 PEC Scope, Definitions & Code Organization (Part 1 vs Part 2) 8.2 General Installation Requirements & Working Space 8.3 Conductor Sizing, Ampacity & Derating 8.4 Overcurrent Protection & Conductor Protection Coordination

10 Chapter 9: Load Calculations & Wiring Methods

9.1 Voltage Drop & Continuous Load Calculations 9.2 Feeders, Load Calculations & Demand Factors 9.3 Wiring Methods: Raceways & Conduit Systems

11 Chapter 10: Cable Systems, Boxes & Wiring Devices

10.1 Wiring Methods: Cable Systems & Flexible Wiring 10.2 Boxes, Enclosures & Fittings 10.3 Wiring Devices, Receptacles & GFCI Protection

12 Chapter 11: Branch Circuits & Services

11.1 Branch Circuits & Multiwire Branch Circuits 11.2 Services & Service Equipment 11.3 Grounding: System & Equipment Grounding

13 Chapter 12: Bonding, Panelboards & Motor Wiring

12.1 Bonding & Grounding Electrode Systems 12.2 Panelboards & Switchboards 12.3 Motor & Generator Wiring, Protection & Disconnects

14 Chapter 13: Motor-Starter Diagrams & Hazardous Locations

13.1 Motor-Starter Wiring Diagrams & Control Symbols 13.2 One-Line Diagrams, Drawing Symbols & Wiring Plans 13.3 Hazardous (Classified) Locations

15 Chapter 14: Special Occupancies, Conditions & Safety

14.1 Special Occupancies (Wet/Damp Locations, Underground Wiring) 14.2 Special Conditions: Emergency Systems & Communications Wiring 14.3 Electrical Safety, PPE & Code-Mandated Working Clearances

16 Chapter 15: Final Review & Next Steps

15.1 RME Exam Strategy, Time Management & Test-Day Tips 15.2 After Passing: PRC Registration, CPD Renewal & Career Paths

6.3 Semiconductor Devices & Basic Solid-State Components

Key Takeaways Explain This Topic AI

A semiconductor's conductivity lies between that of a conductor and an insulator and can be precisely controlled, which is what allows it to be engineered into a one-way or switching device.

A diode conducts current in one direction only — forward bias allows current flow, while reverse bias blocks it — making it the fundamental building block of rectification.

Rectification converts alternating current (AC) to direct current (DC); a single diode produces half-wave rectification, while four diodes arranged in a bridge produce full-wave rectification.

Transistors and thyristors (silicon-controlled rectifiers, SCRs) are solid-state switching devices behind modern variable-speed drives and soft-starters.

Solid-state control equipment still requires proper grounding, surge protection, and enclosure practices in the field, since semiconductor components are sensitive to voltage transients and heat.

Last updated: July 2026

What Makes a Semiconductor Different?

Materials fall along a spectrum of how easily they conduct electric current. A conductor , such as copper or aluminum, offers very little resistance and conducts freely. An insulator , such as rubber or glass, offers extremely high resistance and essentially blocks current flow. A semiconductor — most commonly made from silicon — sits between these two extremes: in its pure form it conducts poorly, but its conductivity can be precisely and deliberately controlled by introducing tiny, controlled amounts of specific impurities, a process called doping . This controllability is what makes semiconductors useful: rather than simply conducting or blocking current uniformly like a conductor or insulator, a semiconductor device can be engineered to conduct current under some conditions and block it under others — the behavior behind every diode, transistor, and thyristor covered in this section. A full explanation of doping and junction physics goes beyond what the RME exam requires; what matters for trade practice is recognizing what these devices do in a circuit, not how their internal physics works.

Diodes: One-Way Current Conduction

A diode is the simplest semiconductor device, built from a single junction between two differently doped regions of semiconductor material. Its defining behavior is that it conducts current in one direction only :

Forward bias — when voltage is applied so that current tries to flow in the diode's permitted direction, the diode's internal resistance drops to a very low value (typically dropping about 0.7 V across a standard silicon diode) and current flows freely.

Reverse bias — when voltage is applied in the opposite direction, the diode presents an extremely high resistance and blocks current flow, up to its rated reverse voltage, beyond which it can be damaged.

This one-way behavior is why a diode's schematic symbol is an arrowhead pointing toward a bar: the arrow shows the permitted direction of conventional current flow, and the bar represents the blocking junction.

Rectification: Converting AC to DC

The most common trade application of a diode is rectification — converting alternating current (AC) to direct current (DC), needed anywhere electronic control equipment, battery chargers, or DC power supplies draw their power from an AC line.

Rectification Type Diodes Used Output Characteristic

Half-wave 1 diode Conducts on only one half of each AC cycle; pulsing DC with large gaps, uses only half of the available waveform

Full-wave (bridge) 4 diodes in a bridge A different diode pair conducts on each half-cycle, but both route current through the load in the same direction; pulsing DC using the full waveform, with shallower and more frequent gaps

Half-wave rectification uses a single diode in series with the AC source and the load. The diode conducts during the half of each cycle when it is forward-biased, passing that half of the waveform through to the load, and blocks during the other half, when it is reverse-biased. The pulsing DC output leaves large gaps that must be smoothed by a filter capacitor (introduced in section 6.2) if a steady DC voltage is needed.

Full-wave rectification uses four diodes arranged in a bridge configuration. On each half-cycle of the AC input, a different pair of diodes conducts, but both pairs route current through the load in the same direction, so the output uses the entire AC cycle, with pulses twice as frequent and far shallower gaps than half-wave rectification. A full-wave bridge rectifier followed by a filter capacitor is the standard front end of most DC power supplies and battery chargers a master electrician will encounter.

Transistors and Thyristors: Solid-State Switching

Beyond simple one-way conduction, semiconductor devices can also act as switches — and, unlike an electromechanical contactor or relay, they switch with no moving parts and can operate far faster and far more often.

A transistor is a three-terminal semiconductor device that can act as an electrically controlled switch, or amplifier: a small control current or voltage at one terminal controls a much larger current between the other two terminals — conceptually similar to how a small coil current in a contactor controls a much larger power-circuit current, but entirely solid-state and without moving contacts.

A thyristor , most commonly encountered in the trade as a silicon-controlled rectifier (SCR) , is a solid-state device that, once triggered on by a small gate signal, conducts current in one direction until the current through it drops to near zero, at which point it turns itself off. By controlling the exact point in the AC waveform where the SCR is triggered, its average conducted power can be varied smoothly — the underlying principle behind solid-state soft-starters , which ramp motor voltage up gradually instead of switching it on abruptly, and the power-conversion stages of variable-frequency drives (VFDs) , which use transistor and thyristor switching to synthesize a variable-frequency, variable-voltage AC output for precise motor speed control.

Core RME theory questions still favor diodes and basic rectification, but a modern master electrician increasingly works with soft-starters and VFDs on the job, so recognizing what a transistor or an SCR is doing functionally — solid-state switching, without moving contacts — is practical, field-relevant knowledge even where exam theory questions go no deeper than rectification.

Grounding and Protection for Solid-State Control Equipment

Solid-state components bring real advantages — no contact wear, no arcing, fast and precise switching — but they are also comparatively delicate. Semiconductor junctions can be permanently damaged by voltage transients, such as lightning-induced surges or the switching spikes produced by nearby inductive loads, by sustained overvoltage, and by excess heat. Because of this sensitivity, a master electrician installing or servicing solid-state control equipment such as VFDs and soft-starters must pay close attention to:

Proper equipment grounding — a solid, low-impedance equipment-grounding path is essential both for personnel safety and to give transient voltages a path to ground rather than through the semiconductor junctions themselves.

Surge and transient protection — surge protective devices and proper conductor separation between power and control wiring reduce the transients that solid-state components are most vulnerable to.

Heat and enclosure considerations — semiconductor devices are rated for a maximum junction temperature, and manufacturers specify heat-sinking and enclosure ventilation requirements that must be respected; a solid-state device operating outside its thermal rating fails far more abruptly than an oversized but simple resistive or electromechanical component would.

Treating solid-state control gear with the same "just wire it up" mindset used for a simple contactor or resistor is a common and costly field mistake. The underlying switching principle may be simpler in some ways, but the components themselves are far less tolerant of transients, overvoltage, and heat than the electromechanical devices covered earlier in this chapter.

Key Takeaways

A semiconductor 's conductivity lies between a conductor and an insulator and can be precisely controlled through doping

A diode conducts in one direction only: forward bias allows current flow, reverse bias blocks it

A single diode produces half-wave rectification ; a four-diode bridge produces full-wave rectification , converting AC to DC

Transistors and thyristors (SCRs) are solid-state switches behind modern soft-starters and variable-frequency drives (VFDs)

Solid-state control equipment requires careful grounding, surge protection, and heat management because semiconductor junctions are sensitive to transients and heat