Study guide

1.2 Kirchhoff's Laws & Series-Parallel Network Analysis

PRC Registered Master Electrician RME

Track your progress as you read

Finished sections get a check mark.

1 Introduction

RME Licensure Examination Overview & RA 7920 Framework How to Use This Study Guide & Build Your Study Plan

2 Chapter 1: DC & AC Circuit Fundamentals

1.1 Ohm's Law & DC Circuit Calculations 1.2 Kirchhoff's Laws & Series-Parallel Network Analysis 1.3 AC Fundamentals: Sine Waves, RMS & Phase Relationships 1.4 AC Circuit Impedance, Reactance & Resonance

3 Chapter 2: AC Power, Three-Phase Systems & DC Generators

2.1 Power in AC Circuits & Power Factor 2.2 Three-Phase Systems: Wye-Delta Configurations & Calculations 2.3 DC Generators: Construction, Types & Characteristics

4 Chapter 3: DC & AC Motors and Starting Methods

3.1 DC Motors: Construction, Types & Speed Control 3.2 AC Induction Motors: Construction, Slip & Synchronous Speed 3.3 Induction Motor Starting Methods

5 Chapter 4: Synchronous Machines & Transformers

4.1 Synchronous Motors & AC Generators (Alternators) 4.2 Transformers: Construction, Turns Ratio & Types 4.3 Transformer Losses, Efficiency, Cooling & Connections

6 Chapter 5: Motor Starters, Control Circuits & Overcurrent Devices

5.1 Motor Starters: DOL, Star-Delta & Autotransformer Starting 5.2 Motor Control Circuits & Overload Protection 5.3 Fuses & Circuit Breakers: Types, Ratings & Applications

7 Chapter 6: Control Devices & Electrical Components

6.1 Contactors, Relays & Other Control Devices 6.2 Electrical Components: Capacitors, Inductors & Resistors 6.3 Semiconductor Devices & Basic Solid-State Components

8 Chapter 7: Maintenance, Test Equipment & RA 7920 Law

7.1 Maintenance & Troubleshooting Practices 7.2 Test Equipment & Electrical Instruments 7.3 RA 7920: RME Law, Scope of Practice & PRC Regulation

9 Chapter 8: PEC Foundations: Scope & General Requirements

8.1 PEC Scope, Definitions & Code Organization (Part 1 vs Part 2) 8.2 General Installation Requirements & Working Space 8.3 Conductor Sizing, Ampacity & Derating 8.4 Overcurrent Protection & Conductor Protection Coordination

10 Chapter 9: Load Calculations & Wiring Methods

9.1 Voltage Drop & Continuous Load Calculations 9.2 Feeders, Load Calculations & Demand Factors 9.3 Wiring Methods: Raceways & Conduit Systems

11 Chapter 10: Cable Systems, Boxes & Wiring Devices

10.1 Wiring Methods: Cable Systems & Flexible Wiring 10.2 Boxes, Enclosures & Fittings 10.3 Wiring Devices, Receptacles & GFCI Protection

12 Chapter 11: Branch Circuits & Services

11.1 Branch Circuits & Multiwire Branch Circuits 11.2 Services & Service Equipment 11.3 Grounding: System & Equipment Grounding

13 Chapter 12: Bonding, Panelboards & Motor Wiring

12.1 Bonding & Grounding Electrode Systems 12.2 Panelboards & Switchboards 12.3 Motor & Generator Wiring, Protection & Disconnects

14 Chapter 13: Motor-Starter Diagrams & Hazardous Locations

13.1 Motor-Starter Wiring Diagrams & Control Symbols 13.2 One-Line Diagrams, Drawing Symbols & Wiring Plans 13.3 Hazardous (Classified) Locations

15 Chapter 14: Special Occupancies, Conditions & Safety

14.1 Special Occupancies (Wet/Damp Locations, Underground Wiring) 14.2 Special Conditions: Emergency Systems & Communications Wiring 14.3 Electrical Safety, PPE & Code-Mandated Working Clearances

16 Chapter 15: Final Review & Next Steps

15.1 RME Exam Strategy, Time Management & Test-Day Tips 15.2 After Passing: PRC Registration, CPD Renewal & Career Paths

1.2 Kirchhoff's Laws & Series-Parallel Network Analysis

Key Takeaways Explain This Topic AI

Kirchhoff's Current Law (KCL) states that the current entering a node equals the current leaving it.

Kirchhoff's Voltage Law (KVL) states that the sum of voltage drops around a closed loop equals the source voltage.

Voltage-divider and current-divider shortcuts find one branch's voltage or current without solving the entire circuit first.

Multi-resistor networks are solved by reducing parallel sections into an equivalent resistor, then verifying the result against both KVL and KCL.

The most common exam traps are applying the wrong law, sign errors in a KVL loop, and overlooking a branch in a multi-branch network.

Last updated: July 2026

Ohm's Law alone can solve simple series or parallel circuits, but real branch-circuit and control-panel wiring often forms networks with multiple loops and junctions that Ohm's Law cannot untangle by itself. Gustav Kirchhoff , a German physicist, published two laws in 1845 that, together with Ohm's Law, can solve any DC network no matter how complex.

Kirchhoff's Current Law (KCL)

Kirchhoff's Current Law (KCL) states that the sum of currents entering a node (junction) equals the sum of currents leaving that node. In other words, charge cannot accumulate at a junction — whatever current flows in must flow out.

I_in = I_out

At a junction where one 10 A supply conductor splits into three branch conductors carrying 4 A, 3 A, and 3 A, KCL confirms the split is valid: 4 + 3 + 3 = 10 A.

Exam tip: KCL applies at nodes (junction points), not around loops. If a question describes a wire splitting or joining, you're applying KCL.

Kirchhoff's Voltage Law (KVL)

Kirchhoff's Voltage Law (KVL) states that the sum of the voltage drops around any closed loop equals the source voltage supplying that loop — or equivalently, the algebraic sum of all voltage rises and drops around a closed loop equals zero.

V_source = V_drop1 + V_drop2 + V_drop3 + ...

This is the same rule verified in Section 1.1's series-circuit example, where 20 V + 30 V dropped across two resistors equaled the 50 V source. KVL simply generalizes that rule to loops that may contain multiple sources and branches.

Exam tip: KVL applies around closed loops (a complete path that returns to its starting point), not at single junctions. If a question describes tracing a path around a circuit, you're applying KVL.

Voltage-Divider Reasoning

Because voltage drops in a series string are proportional to resistance, you can find the voltage across any one resistor without first solving for current. The voltage-divider formula for a resistor R_x in a series string is:

V_x = V_source × (R_x / R_total)

This shortcut is common on trade exams that ask for the voltage across one resistor in a series string without asking for current.

Current-Divider Reasoning

In a parallel network, current splits between branches in inverse proportion to resistance — the lower-resistance branch carries more current. For exactly two parallel resistors, the current-divider formula for the current through R1 is:

I_1 = I_total × (R2 / (R1 + R2))

Notice the crossed pattern: the current through R1 uses R2 in the numerator, and vice versa.

  • Solving a Series-Parallel Network Step by Step
  • Worked Example — Multi-Resistor Network

A 60 V DC source feeds R1 = 5 Ω in series with a parallel combination of R2 = 12 Ω and R3 = 6 Ω, which is itself in series with R4 = 3 Ω.

  • Step 1 — Reduce the parallel section. R_23 = (R2 × R3)/(R2 + R3) = (12 × 6)/(12+6) = 72/18 = 4 Ω
  • Step 2 — Add the series resistors. R_T = R1 + R_23 + R4 = 5 + 4 + 3 = 12 Ω

Step 3 — Apply Ohm's Law for total current. I_T = V / R_T = 60 / 12 = 5 A (this current flows through R1 and R4, and is the total current entering the parallel section)

  • Step 4 — Find the voltage across each series element using KVL. V1 = I_T × R1 = 5 × 5 = 25 V
  • V_23 = I_T × R_23 = 5 × 4 = 20 V
  • V4 = I_T × R4 = 5 × 3 = 15 V
  • Check (KVL): 25 + 20 + 15 = 60 V, matching the source

Step 5 — Find the branch currents through R2 and R3 using Ohm's Law and confirm with KCL. I2 = V_23 / R2 = 20 / 12 = 1.67 A

  • I3 = V_23 / R3 = 20 / 6 = 3.33 A
  • Check (KCL): I2 + I3 = 1.67 + 3.33 = 5 A, matching I_T

Every worked network problem should end with these two checks — KVL around the loop and KCL at the junction — because they catch arithmetic errors before they cost you exam points.

Common Trade-Exam Traps

Confusing which law applies. KCL is about current at a point (a node); KVL is about voltage around a path (a loop). A question that mentions a junction splitting wires needs KCL; a question that asks you to trace a complete circuit path needs KVL.

Sign errors in KVL. When tracing a loop, a voltage rise (through a source, moving from − to +) and a voltage drop (across a resistor, in the direction of current flow) have opposite signs. Skipping this bookkeeping is the single most common reason candidates get the right magnitude but the wrong direction on a KVL problem.

Forgetting a branch. In networks with three or more parallel branches, it's easy to compute only two branch currents and forget the third exists — always recount the branches against the schematic before finalizing an answer, and use the KCL check as a safety net.

Applying series rules to a parallel section, or vice versa. Before combining any two resistors, confirm whether they share the same two nodes (parallel) or carry the same single current path with no other branch (series).

Key Takeaways

KCL: the sum of currents into a node equals the sum of currents out — apply it at junctions.

KVL: the sum of voltage drops around a closed loop equals the source voltage — apply it around loops.

Voltage dividers split voltage in proportion to resistance; current dividers split current in inverse proportion to resistance.

Multi-resistor networks are solved by reducing parallel sections first, then applying Ohm's Law and KVL/KCL as checks — always verify your final answer against both laws.