Study guide

1.1 Ohm's Law & DC Circuit Calculations

PRC Registered Master Electrician RME

Track your progress as you read

Finished sections get a check mark.

1 Introduction

RME Licensure Examination Overview & RA 7920 Framework How to Use This Study Guide & Build Your Study Plan

2 Chapter 1: DC & AC Circuit Fundamentals

1.1 Ohm's Law & DC Circuit Calculations 1.2 Kirchhoff's Laws & Series-Parallel Network Analysis 1.3 AC Fundamentals: Sine Waves, RMS & Phase Relationships 1.4 AC Circuit Impedance, Reactance & Resonance

3 Chapter 2: AC Power, Three-Phase Systems & DC Generators

2.1 Power in AC Circuits & Power Factor 2.2 Three-Phase Systems: Wye-Delta Configurations & Calculations 2.3 DC Generators: Construction, Types & Characteristics

4 Chapter 3: DC & AC Motors and Starting Methods

3.1 DC Motors: Construction, Types & Speed Control 3.2 AC Induction Motors: Construction, Slip & Synchronous Speed 3.3 Induction Motor Starting Methods

5 Chapter 4: Synchronous Machines & Transformers

4.1 Synchronous Motors & AC Generators (Alternators) 4.2 Transformers: Construction, Turns Ratio & Types 4.3 Transformer Losses, Efficiency, Cooling & Connections

6 Chapter 5: Motor Starters, Control Circuits & Overcurrent Devices

5.1 Motor Starters: DOL, Star-Delta & Autotransformer Starting 5.2 Motor Control Circuits & Overload Protection 5.3 Fuses & Circuit Breakers: Types, Ratings & Applications

7 Chapter 6: Control Devices & Electrical Components

6.1 Contactors, Relays & Other Control Devices 6.2 Electrical Components: Capacitors, Inductors & Resistors 6.3 Semiconductor Devices & Basic Solid-State Components

8 Chapter 7: Maintenance, Test Equipment & RA 7920 Law

7.1 Maintenance & Troubleshooting Practices 7.2 Test Equipment & Electrical Instruments 7.3 RA 7920: RME Law, Scope of Practice & PRC Regulation

9 Chapter 8: PEC Foundations: Scope & General Requirements

8.1 PEC Scope, Definitions & Code Organization (Part 1 vs Part 2) 8.2 General Installation Requirements & Working Space 8.3 Conductor Sizing, Ampacity & Derating 8.4 Overcurrent Protection & Conductor Protection Coordination

10 Chapter 9: Load Calculations & Wiring Methods

9.1 Voltage Drop & Continuous Load Calculations 9.2 Feeders, Load Calculations & Demand Factors 9.3 Wiring Methods: Raceways & Conduit Systems

11 Chapter 10: Cable Systems, Boxes & Wiring Devices

10.1 Wiring Methods: Cable Systems & Flexible Wiring 10.2 Boxes, Enclosures & Fittings 10.3 Wiring Devices, Receptacles & GFCI Protection

12 Chapter 11: Branch Circuits & Services

11.1 Branch Circuits & Multiwire Branch Circuits 11.2 Services & Service Equipment 11.3 Grounding: System & Equipment Grounding

13 Chapter 12: Bonding, Panelboards & Motor Wiring

12.1 Bonding & Grounding Electrode Systems 12.2 Panelboards & Switchboards 12.3 Motor & Generator Wiring, Protection & Disconnects

14 Chapter 13: Motor-Starter Diagrams & Hazardous Locations

13.1 Motor-Starter Wiring Diagrams & Control Symbols 13.2 One-Line Diagrams, Drawing Symbols & Wiring Plans 13.3 Hazardous (Classified) Locations

15 Chapter 14: Special Occupancies, Conditions & Safety

14.1 Special Occupancies (Wet/Damp Locations, Underground Wiring) 14.2 Special Conditions: Emergency Systems & Communications Wiring 14.3 Electrical Safety, PPE & Code-Mandated Working Clearances

16 Chapter 15: Final Review & Next Steps

15.1 RME Exam Strategy, Time Management & Test-Day Tips 15.2 After Passing: PRC Registration, CPD Renewal & Career Paths

1.1 Ohm's Law & DC Circuit Calculations

Key Takeaways Explain This Topic AI

Ohm's Law (V = IR) and its two rearrangements (I = V/R, R = V/I) solve for any single unknown when the other two quantities are known.

Power can be calculated three ways — P = VI, P = I²R, or P = V²/R — depending on which two quantities are already known.

In series circuits, current is identical everywhere and voltage drops add to the source voltage; in parallel circuits, voltage is identical across every branch and currents add to the total.

Total parallel resistance is always less than the smallest individual resistor in the combination.

Combined series-parallel circuits are solved by reducing parallel sections into an equivalent resistance before applying series rules.

Last updated: July 2026

Every electrical calculation an examinee performs on the Technical Subjects portion of the board exam — from sizing a branch-circuit conductor to troubleshooting a tripped breaker — traces back to one relationship. Ohm's Law , named after German physicist Georg Simon Ohm, states that the current flowing through a conductor between two points is directly proportional to the voltage across those two points and inversely proportional to the resistance between them.

The Three Forms of Ohm's Law

Direct current (DC) is current that flows in one direction only, unlike alternating current (AC), which reverses direction periodically. In a DC circuit, three quantities are always related:

Voltage (V) , measured in volts, is the electrical "pressure" that pushes current through a circuit.

Current (I) , measured in amperes (A), is the rate of flow of electric charge.

Resistance (R) , measured in ohms (Ω), is the opposition to that flow.

Ohm's Law expresses this relationship as:

V = I × R

Because any one of the three variables can be the unknown, the formula rearranges into three usable forms:

  • To Find Formula Read As
  • Voltage V = I × R Voltage equals current times resistance
  • Current I = V / R Current equals voltage divided by resistance
  • Resistance R = V / I Resistance equals voltage divided by current

Exam tip: Many reviewees memorize the "Ohm's Law wheel" — a circle divided into V, I, and R. Cover the unknown quantity and the remaining two show whether to multiply or divide.

Power Formulas

Power (P) , measured in watts (W), is the rate at which electrical energy is converted into another form (heat, light, mechanical motion). Because power is the product of voltage and current, and because V and I are themselves related through resistance, power has three equivalent formulas:

  • To Find Formula When to Use
  • Power P = V × I You know voltage and current
  • Power P = I² × R You know current and resistance
  • Power P = V² / R You know voltage and resistance

These three power formulas, combined with the three Ohm's Law forms, form a complete formula "wheel" — every combination of two known quantities lets you solve for either of the other two (V, I, R, or P).

Worked Example 1 — Solving for Resistance

A DC-powered control relay is rated to draw 2.5 A when connected to a 24 V DC source. What is the resistance of the relay coil?

Using R = V / I:

  • R = 24 V / 2.5 A = 9.6 Ω
  • Worked Example 2 — Solving for Current from Power

A 120 V DC heating element is rated at 1,500 W . What current does it draw?

Using I = P / V (derived from P = V × I):

I = 1,500 W / 120 V = 12.5 A

Once current is known, resistance can also be found: R = V / I = 120 / 12.5 = 9.6 Ω . Cross-checking a result with a second formula — computing R two different ways — is a fast way to catch arithmetic mistakes on the exam.

Series Circuits

In a series circuit , components are connected end-to-end so there is only one path for current. Three rules govern series circuits:

  • Current is the same at every point in the circuit: I_T = I_1 = I_2 = I_3
  • Voltage drops add up to equal the source voltage: V_T = V_1 + V_2 + V_3
  • Resistances add directly : R_T = R_1 + R_2 + R_3
  • Worked Example 3 — Series Resistors

Two resistors, R1 = 20 Ω and R2 = 30 Ω , are connected in series across a 50 V DC source.

  • Total resistance: R_T = 20 + 30 = 50 Ω
  • Total (and branch) current: I = V / R_T = 50 / 50 = 1 A
  • Voltage drop across R1: V1 = I × R1 = 1 × 20 = 20 V
  • Voltage drop across R2: V2 = I × R2 = 1 × 30 = 30 V

Check: 20 V + 30 V = 50 V, matching the source — confirming Kirchhoff's Voltage Law (covered fully in Section 1.2).

Parallel Circuits

In a parallel circuit , components are connected across the same two nodes, so current has multiple paths available. The rules invert compared to series:

  • Voltage is the same across every branch: V_T = V_1 = V_2 = V_3
  • Currents add up to equal the total current: I_T = I_1 + I_2 + I_3
  • Resistances combine reciprocally : 1/R_T = 1/R_1 + 1/R_2 + 1/R_3

For exactly two resistors, this simplifies to the convenient "product over sum" shortcut: R_T = (R1 × R2) / (R1 + R2).

Worked Example 4 — Parallel Resistors

R1 = 20 Ω and R2 = 30 Ω are connected in parallel across the same 50 V source.

  • Total resistance: R_T = (20 × 30) / (20 + 30) = 600 / 50 = 12 Ω
  • Branch current through R1: I1 = V / R1 = 50 / 20 = 2.5 A
  • Branch current through R2: I2 = V / R2 = 50 / 30 = 1.67 A
  • Total current: I_T = 2.5 + 1.67 = 4.17 A

Notice that total resistance in parallel (12 Ω) is always less than the smallest individual resistor (20 Ω) — a useful sanity check on the exam.

Combined Series-Parallel Circuits

Real branch-circuit wiring is rarely purely series or purely parallel. A combined (series-parallel) circuit is solved by reducing it in stages: collapse parallel branches into a single equivalent resistance first, then treat that equivalent as one series element.

Worked Example 5 — Combined Circuit

A 100 V DC source feeds R1 = 10 Ω in series with a parallel combination of R2 = 20 Ω and R3 = 20 Ω.

  • Reduce the parallel pair: R_23 = (20 × 20)/(20+20) = 400/40 = 10 Ω
  • Add the series resistor: R_T = R1 + R_23 = 10 + 10 = 20 Ω
  • Total current from the source: I_T = V / R_T = 100 / 20 = 5 A
  • Voltage across the parallel section: V_23 = I_T × R_23 = 5 × 10 = 50 V
  • Each parallel branch carries: I2 = I3 = 50 V / 20 Ω = 2.5 A (equal because R2 = R3)
  • Formula Summary Table
  • Quantity Formula(s)
  • Voltage V = IR
  • Current I = V/R

Resistance (series) R_T = R1 + R2 + ...

  • Resistance (parallel) 1/R_T = 1/R1 + 1/R2 + ... (or R1R2/(R1+R2) for two resistors)
  • Power P = VI = I²R = V²/R
  • Key Takeaways

Ohm's Law (V = IR) and its two rearrangements (I = V/R, R = V/I) are the base of nearly every numeric problem in this exam group.

Power has three equivalent formulas — pick the one that matches the two quantities you already know.

Series circuits share one current path; parallel circuits share one voltage across all branches.

Reduce combined circuits by collapsing parallel sections into an equivalent resistance before treating the circuit as series.