Study guide

13.3 Hazardous (Classified) Locations

PRC Registered Master Electrician RME

Track your progress as you read

Finished sections get a check mark.

1 Introduction

RME Licensure Examination Overview & RA 7920 Framework How to Use This Study Guide & Build Your Study Plan

2 Chapter 1: DC & AC Circuit Fundamentals

1.1 Ohm's Law & DC Circuit Calculations 1.2 Kirchhoff's Laws & Series-Parallel Network Analysis 1.3 AC Fundamentals: Sine Waves, RMS & Phase Relationships 1.4 AC Circuit Impedance, Reactance & Resonance

3 Chapter 2: AC Power, Three-Phase Systems & DC Generators

2.1 Power in AC Circuits & Power Factor 2.2 Three-Phase Systems: Wye-Delta Configurations & Calculations 2.3 DC Generators: Construction, Types & Characteristics

4 Chapter 3: DC & AC Motors and Starting Methods

3.1 DC Motors: Construction, Types & Speed Control 3.2 AC Induction Motors: Construction, Slip & Synchronous Speed 3.3 Induction Motor Starting Methods

5 Chapter 4: Synchronous Machines & Transformers

4.1 Synchronous Motors & AC Generators (Alternators) 4.2 Transformers: Construction, Turns Ratio & Types 4.3 Transformer Losses, Efficiency, Cooling & Connections

6 Chapter 5: Motor Starters, Control Circuits & Overcurrent Devices

5.1 Motor Starters: DOL, Star-Delta & Autotransformer Starting 5.2 Motor Control Circuits & Overload Protection 5.3 Fuses & Circuit Breakers: Types, Ratings & Applications

7 Chapter 6: Control Devices & Electrical Components

6.1 Contactors, Relays & Other Control Devices 6.2 Electrical Components: Capacitors, Inductors & Resistors 6.3 Semiconductor Devices & Basic Solid-State Components

8 Chapter 7: Maintenance, Test Equipment & RA 7920 Law

7.1 Maintenance & Troubleshooting Practices 7.2 Test Equipment & Electrical Instruments 7.3 RA 7920: RME Law, Scope of Practice & PRC Regulation

9 Chapter 8: PEC Foundations: Scope & General Requirements

8.1 PEC Scope, Definitions & Code Organization (Part 1 vs Part 2) 8.2 General Installation Requirements & Working Space 8.3 Conductor Sizing, Ampacity & Derating 8.4 Overcurrent Protection & Conductor Protection Coordination

10 Chapter 9: Load Calculations & Wiring Methods

9.1 Voltage Drop & Continuous Load Calculations 9.2 Feeders, Load Calculations & Demand Factors 9.3 Wiring Methods: Raceways & Conduit Systems

11 Chapter 10: Cable Systems, Boxes & Wiring Devices

10.1 Wiring Methods: Cable Systems & Flexible Wiring 10.2 Boxes, Enclosures & Fittings 10.3 Wiring Devices, Receptacles & GFCI Protection

12 Chapter 11: Branch Circuits & Services

11.1 Branch Circuits & Multiwire Branch Circuits 11.2 Services & Service Equipment 11.3 Grounding: System & Equipment Grounding

13 Chapter 12: Bonding, Panelboards & Motor Wiring

12.1 Bonding & Grounding Electrode Systems 12.2 Panelboards & Switchboards 12.3 Motor & Generator Wiring, Protection & Disconnects

14 Chapter 13: Motor-Starter Diagrams & Hazardous Locations

13.1 Motor-Starter Wiring Diagrams & Control Symbols 13.2 One-Line Diagrams, Drawing Symbols & Wiring Plans 13.3 Hazardous (Classified) Locations

15 Chapter 14: Special Occupancies, Conditions & Safety

14.1 Special Occupancies (Wet/Damp Locations, Underground Wiring) 14.2 Special Conditions: Emergency Systems & Communications Wiring 14.3 Electrical Safety, PPE & Code-Mandated Working Clearances

16 Chapter 15: Final Review & Next Steps

15.1 RME Exam Strategy, Time Management & Test-Day Tips 15.2 After Passing: PRC Registration, CPD Renewal & Career Paths

13.3 Hazardous (Classified) Locations

Key Takeaways Explain This Topic AI

A classified (hazardous) location is an area where flammable gases/vapors, combustible dust, or ignitible fibers/flyings may be present in quantities sufficient to produce an explosive or ignitible mixture.

Class I covers flammable gases and vapors, Class II covers combustible dust, and Class III covers ignitible fibers and flyings.

Division 1 means the hazardous condition exists under normal operating conditions; Division 2 means it exists only under abnormal conditions, such as equipment or container failure.

Ordinary wiring devices and fixtures are prohibited in classified locations because arcing contacts and hot surfaces can ignite the surrounding atmosphere; explosion-proof and dust-ignition-proof ratings address this in different ways.

Sealing fittings are required where conduit crosses between a classified and unclassified area, both to block gas/vapor migration and to contain the pressure of an internal explosion.

Last updated: July 2026

13.3 Hazardous (Classified) Locations

Not every location an RME wires is equally forgiving of a spark. Some occupancies — paint booths, fuel stations, grain facilities, textile plants — routinely contain flammable gases, vapors, combustible dusts, or ignitible fibers in the air itself. In these classified (hazardous) locations , an electrical fault that would be a minor nuisance anywhere else can ignite the surrounding atmosphere. The PEC's hazardous-location provisions, structurally adapted from the same Class/Division framework used in the US National Electrical Code, exist to keep normal electrical operation — switching, motor starting, even a loose connection — from becoming an ignition source.

What Makes a Location "Classified"

A location is classified when flammable gases or vapors, combustible dust, or easily ignitible fibers or flyings may be present in the air in quantities sufficient to produce an explosive or ignitible mixture — whether that condition exists continuously, intermittently during normal operations, or only as the result of an abnormal event such as a leak or a container failure. The classification is a property of the occupancy and process , not of the building type: two rooms in the same building, one where solvents are actively sprayed and one where they are only stored in closed drums, can carry different classifications.

The Class System

  • Class Hazard Typical materials
  • Class I Flammable gases or vapors Gasoline vapor, solvent vapor, propane, natural gas
  • Class II Combustible dust Grain dust, flour, sugar dust, coal dust, metal dust
  • Class III Ignitible fibers or flyings Cotton lint, textile fibers, sawdust, wood flyings
  • The Division System

Within each Class, a Division describes how often and under what conditions the hazard is actually present.

Division Condition

Division 1 The hazardous atmosphere exists under normal operating conditions, or exists frequently because of repair/maintenance operations or leakage, or could be produced by equipment failure that simultaneously causes the electrical equipment itself to fail

Division 2 The hazardous material is normally confined within closed containers or systems and is present in the air only if that confinement fails — through an accidental rupture, a breakdown, or abnormal operation

Class and Division in Real Occupancies

Location example Class Division Why

Interior of an active spray-paint booth I 1 Flammable solvent vapors are present in the air during normal spraying operations

Area immediately adjacent to a spray booth, outside the booth itself I 2 Vapors are normally confined to the booth and its exhaust; they reach this area only if containment or ventilation fails

Area immediately surrounding a fuel dispenser at a filling station I 1 or 2, depending on distance and height Gasoline vapors are released during routine fueling near the nozzle; the hazard tapers off with distance and elevation, which is why the classified zone is defined as a boundary around the dispenser rather than the whole station

Interior of a grain elevator or flour-milling area II 1 Combustible dust is suspended in the air as a normal part of processing

A dust-collection or storage room where dust settles on surfaces but is not normally airborne II 2 Dust is normally confined to equipment; a hazardous suspension occurs only if that equipment fails

Interior of a textile mill processing area III 1 Ignitible fibers and lint are handled and generated as part of normal production

A fiber or lint storage area, separate from active processing III 2 Fibers are stored, not actively processed; airborne concentration under normal conditions is much lower

Why Ordinary Wiring Methods and Devices Are Prohibited

Ordinary switches, receptacles, motor brushes, and even loose or arcing connections routinely produce small sparks or localized heat as a normal part of operation — a switch contact arcs every time it opens, a motor's brushes spark against the commutator, an overloaded conductor runs hot. None of that matters in an ordinary room. In a classified location, any of it can be the ignition source for the surrounding atmosphere. This is why classified locations require wiring methods, devices, and fixtures specifically listed for the applicable Class and Division rather than ordinary commercial-grade equipment.

Two equipment ratings address this differently, because Class I and Class II hazards behave differently:

Explosion-proof (Class I) equipment is not built to prevent an internal spark from occurring — it is built to contain one. If an internal arc ignites gas that has entered the enclosure, the enclosure is strong enough to withstand that internal explosion without rupturing, and its joints (often long, closely machined threaded joints) are designed to cool the escaping combustion gases below their ignition temperature before they can reach the surrounding atmosphere.

Dust-ignition-proof (Class II) equipment takes the opposite strategy: because a dust-air mixture is generally ignited by hot surfaces or entry of a spark rather than by internal pressure the way gas is, this equipment is built to exclude dust from entering the enclosure at all, and to keep its external operating-surface temperature below the ignition temperature of the specific dust involved.

Sealing Requirements

Wherever a conduit or raceway crosses the boundary between a classified location and an unclassified area — or between a Division 1 and a Division 2 area — it must be fitted with a sealing fitting packed with an approved sealing compound. The seal serves two distinct purposes: it prevents gases or vapors from migrating along the inside of the raceway from the hazardous side into the unclassified side, and it is strong enough to contain the pressure of an internal explosion inside the raceway so that ignited gas cannot travel through the conduit and ignite atmosphere somewhere else in the building. Both functions matter — a raceway is a hidden pathway, and without a seal it can carry a hazard, or a fire, far outside the room where the classification was intended to stop it.

RME Scenarios

Classifying a small automotive repair garage's spray area. A shop owner asks whether their small touch-up spray area needs the full hazardous-location treatment. The RME's judgment starts with the process, not the room size: if solvent-based paint is actively sprayed inside that space as part of normal operations, the interior of the spraying area is Class I, Division 1 while spraying is occurring, because flammable vapor is present under normal operating conditions. Adjacent areas that only receive vapor if ventilation fails are Division 2. A properly designed and continuously operated spray-booth exhaust system changes the practical extent of the classified zone, but it does not eliminate the need to treat the booth interior itself as Division 1 — the RME must specify listed Class I equipment inside the booth regardless of how good the ventilation is.

Wiring near a fuel dispenser. An RME asked to add lighting or power near a gas-station fuel dispenser must first establish the classified boundary around and above the dispenser, then select wiring methods, devices, and fixtures listed for that Class I Division. Ordinary flexible cord, a standard duplex receptacle, or an unlisted light fixture within that zone are all prohibited; any conduit run leaving the classified zone toward the station's unclassified interior must include a sealing fitting at the boundary so vapor cannot travel back through the raceway into the building.