Study guide
7.1 Maintenance & Troubleshooting Practices
PRC Registered Master Electrician RME
Track your progress as you read
Finished sections get a check mark.
1 Introduction
RME Licensure Examination Overview & RA 7920 Framework How to Use This Study Guide & Build Your Study Plan
2 Chapter 1: DC & AC Circuit Fundamentals
1.1 Ohm's Law & DC Circuit Calculations 1.2 Kirchhoff's Laws & Series-Parallel Network Analysis 1.3 AC Fundamentals: Sine Waves, RMS & Phase Relationships 1.4 AC Circuit Impedance, Reactance & Resonance
3 Chapter 2: AC Power, Three-Phase Systems & DC Generators
2.1 Power in AC Circuits & Power Factor 2.2 Three-Phase Systems: Wye-Delta Configurations & Calculations 2.3 DC Generators: Construction, Types & Characteristics
4 Chapter 3: DC & AC Motors and Starting Methods
3.1 DC Motors: Construction, Types & Speed Control 3.2 AC Induction Motors: Construction, Slip & Synchronous Speed 3.3 Induction Motor Starting Methods
5 Chapter 4: Synchronous Machines & Transformers
4.1 Synchronous Motors & AC Generators (Alternators) 4.2 Transformers: Construction, Turns Ratio & Types 4.3 Transformer Losses, Efficiency, Cooling & Connections
6 Chapter 5: Motor Starters, Control Circuits & Overcurrent Devices
5.1 Motor Starters: DOL, Star-Delta & Autotransformer Starting 5.2 Motor Control Circuits & Overload Protection 5.3 Fuses & Circuit Breakers: Types, Ratings & Applications
7 Chapter 6: Control Devices & Electrical Components
6.1 Contactors, Relays & Other Control Devices 6.2 Electrical Components: Capacitors, Inductors & Resistors 6.3 Semiconductor Devices & Basic Solid-State Components
8 Chapter 7: Maintenance, Test Equipment & RA 7920 Law
7.1 Maintenance & Troubleshooting Practices 7.2 Test Equipment & Electrical Instruments 7.3 RA 7920: RME Law, Scope of Practice & PRC Regulation
9 Chapter 8: PEC Foundations: Scope & General Requirements
8.1 PEC Scope, Definitions & Code Organization (Part 1 vs Part 2) 8.2 General Installation Requirements & Working Space 8.3 Conductor Sizing, Ampacity & Derating 8.4 Overcurrent Protection & Conductor Protection Coordination
10 Chapter 9: Load Calculations & Wiring Methods
9.1 Voltage Drop & Continuous Load Calculations 9.2 Feeders, Load Calculations & Demand Factors 9.3 Wiring Methods: Raceways & Conduit Systems
11 Chapter 10: Cable Systems, Boxes & Wiring Devices
10.1 Wiring Methods: Cable Systems & Flexible Wiring 10.2 Boxes, Enclosures & Fittings 10.3 Wiring Devices, Receptacles & GFCI Protection
12 Chapter 11: Branch Circuits & Services
11.1 Branch Circuits & Multiwire Branch Circuits 11.2 Services & Service Equipment 11.3 Grounding: System & Equipment Grounding
13 Chapter 12: Bonding, Panelboards & Motor Wiring
12.1 Bonding & Grounding Electrode Systems 12.2 Panelboards & Switchboards 12.3 Motor & Generator Wiring, Protection & Disconnects
14 Chapter 13: Motor-Starter Diagrams & Hazardous Locations
13.1 Motor-Starter Wiring Diagrams & Control Symbols 13.2 One-Line Diagrams, Drawing Symbols & Wiring Plans 13.3 Hazardous (Classified) Locations
15 Chapter 14: Special Occupancies, Conditions & Safety
14.1 Special Occupancies (Wet/Damp Locations, Underground Wiring) 14.2 Special Conditions: Emergency Systems & Communications Wiring 14.3 Electrical Safety, PPE & Code-Mandated Working Clearances
16 Chapter 15: Final Review & Next Steps
15.1 RME Exam Strategy, Time Management & Test-Day Tips 15.2 After Passing: PRC Registration, CPD Renewal & Career Paths
7.1 Maintenance & Troubleshooting Practices
Key Takeaways Explain This Topic AI
Preventive maintenance follows a fixed schedule to catch degradation before failure; corrective maintenance repairs equipment only after it has already failed.
A systematic troubleshooting approach — visual inspection, verify/isolate power, check continuity/resistance, compare to nameplate values, then isolate the specific fault — prevents needless part replacement.
Common failure modes include insulation degradation, loose terminations, worn brushes/commutators on DC machines, bearing wear, and overload-relay nuisance trips versus genuine overloads.
Lockout/Tagout (LOTO) requires isolating energy sources and verifying a zero-energy state with a meter — a disconnect's off position alone is not proof a circuit is safe.
Insulation-resistance testing with a megohmmeter is a core preventive-maintenance and diagnostic tool, covered in depth in Section 7.2.
Last updated: July 2026
Preventive Maintenance vs. Corrective Maintenance
Every Registered Master Electrician (RME) spends as much career time keeping electrical systems running safely as installing them in the first place. RA 7920 lists maintenance and repair as its own examinable Technical Subjects item, and the exam expects you to know not just how to fix a failed component, but how a professional maintenance program is organized.
Preventive maintenance (PM) is inspection, testing, cleaning, adjustment, and servicing performed on a fixed schedule — by calendar interval or by run-hours — regardless of whether the equipment is currently showing a problem. The goal of PM is to catch degradation (a loosening terminal, a weakening insulation system, a worn bearing) while it is still a minor finding, and correct it before it becomes an unplanned outage or a safety hazard. Typical PM tasks include periodic insulation-resistance testing, torque-checking terminations, cleaning ventilation openings and contacts, lubricating bearings on schedule, and trending test readings over time so a slow decline is visible before failure.
Corrective maintenance (CM) , by contrast, is repair work performed after a failure has already occurred — a motor has stopped, a breaker has tripped and will not reset, a circuit has gone dead. CM is reactive by definition: the electrician is responding to a fault that has already interrupted service, often under time pressure. CM is unavoidable — no PM program eliminates all failures — but a facility that relies on CM alone (run-to-failure) pays for it in unplanned downtime, expedited parts and labor costs, and a higher risk that a failure occurs in a way that endangers people or damages adjacent equipment.
- Factor Preventive Maintenance Corrective Maintenance
- Trigger Fixed schedule or run-hours, regardless of symptoms Equipment has already failed, tripped, or stopped
- Typical cost Lower — planned labor and parts Higher — emergency labor, expedited parts, lost production
- Downtime Scheduled and minimized Unplanned; can idle production or life-safety systems
RME's role Inspect, test, clean, lubricate, tighten, and trend readings Diagnose the fault, isolate it, repair or replace, verify safe restart
A well-run maintenance program uses PM to minimize how often CM is needed — but every RME must be equally competent at both.
A Systematic Troubleshooting Approach
When a fault does occur, the exam rewards a disciplined, repeatable troubleshooting method over guesswork. Jumping straight to swapping a part and seeing if that fixes it wastes time, wastes parts, and — on a live system — is dangerous. A systematic approach follows a consistent order:
Visual inspection first. Before touching a meter or a tool, look for the obvious: burn marks, discoloration on a terminal or bus bar, melted insulation, a tripped breaker handle, a blown fuse window, corrosion, or a loose or disconnected wire. Many faults reveal themselves this way, and this step costs nothing but attention.
Verify power and isolate the circuit. Confirm what state the circuit is actually in — energized or de-energized — rather than assuming. If the equipment must be serviced, de-energize and isolate it (see Lockout/Tagout below) before opening it up; if diagnosis genuinely requires live readings, treat the circuit with full respect for the hazard the entire time.
Check continuity and resistance before condemning a component. Do not assume a motor winding, a fuse, or a control coil is bad. Measure it. A quick continuity or resistance check on a de-energized circuit will confirm or rule out a suspect component in seconds, and prevents the common mistake of replacing a good part while the actual fault remains untouched.
Compare readings to nameplate or expected values. A resistance or current reading only means something in context. Compare what you measure to the equipment's nameplate data, the manufacturer's expected values, or a known-good reading from an identical circuit or machine. A winding resistance far outside the expected range — high (open turns, a burned winding) or unusually low (shorted turns) — points directly at the fault.
Isolate the specific faulty component. The goal of steps 1 through 4 is to narrow the fault down to one specific component or connection, not to replace an entire assembly on suspicion. Replacing more than the actual faulty part wastes money, can introduce new problems, and — because it does not train you to actually diagnose — leaves you unprepared for the next fault.
This order matters because each step narrows the search before the next step risks touching a component or applying test voltage. Skipping straight to component replacement, or skipping the isolation and verification steps to save time, is both an inefficient troubleshooting habit and — on live equipment — an avoidable safety risk.
Common Motor and Wiring Maintenance Issues
A master electrician's day-to-day maintenance work concentrates on a recurring set of failure modes:
Issue Typical Symptom Underlying Cause Corrective Action
Insulation degradation / moisture ingress Nuisance ground-fault trips, declining insulation-resistance readings Aging insulation, contamination, condensation, or water entry Dry out and clean the winding/enclosure; retest with a megohmmeter; repair or rewind if resistance stays low
Loose terminations Localized heat, discoloration, arcing, intermittent operation Vibration loosening a screw terminal or lug over time; improper initial torque Re-torque to the manufacturer's specification; replace any heat-damaged conductor or lug
Worn brushes / commutator (DC machines) Excessive sparking at the brushes; uneven or grooved commutator surface Normal wear from continuous brush-to-commutator contact Inspect brush length and spring tension on schedule; replace worn brushes; resurface a scored commutator
Bearing wear Unusual noise, vibration, or overheating at the bearing housing Lubricant breakdown, contamination, or end-of-service-life wear Follow the lubrication schedule; replace bearings before they seize and damage the shaft or windings
Overload-relay nuisance tripping Relay trips repeatedly even though the motor is not actually overloaded Mismatched or misadjusted heater element, or an ambient-temperature difference between the relay location and the motor Verify the heater/relay is sized to the motor's actual nameplate current and correct for ambient conditions
Overload-relay tripping from a genuine overload Relay trips and the motor is measurably drawing above nameplate current Mechanical binding, a jammed load, low supply voltage, or single-phasing Investigate and correct the mechanical or electrical root cause before resetting — do not simply oversize the heater
The last two rows matter most on the exam: an RME must be able to tell a nuisance trip (the protection is working, but is miscalibrated) apart from a genuine overload (the protection is doing exactly its job, and something on the load side is actually wrong). Defeating or oversizing protection just to stop a genuine overload from tripping removes the very protection that prevents winding damage or fire.
Lockout/Tagout (LOTO): De-Energizing Before Service
Lockout/Tagout (LOTO) is the practice of physically isolating an energy source, applying a personal lock and a warning tag to the isolating device, and then verifying — with a meter, not by assumption — that the circuit is actually at a zero-energy state before anyone works on it. LOTO exists because a switch being off is not the same guarantee as a circuit being safe. A disconnect can be mislabeled, a control circuit can be back-fed from another source, a capacitor can hold a stored charge after the supply is removed, and a breaker can be re-energized by someone else who does not know work is in progress.
A basic LOTO sequence includes: notifying anyone affected before the outage, identifying every energy source feeding the equipment (not just the obvious one), shutting the equipment down through its normal stopping procedure, opening and isolating the disconnecting means, applying a lock and tag that only the worker performing the work can remove, relieving or blocking any stored energy (capacitors, springs, elevated loads), and then testing the circuit with a meter to confirm zero energy before contact begins.
LOTO is not a best practice that a careful electrician can skip when in a hurry — it is a core, non-negotiable safety discipline, because the entire troubleshooting and maintenance process described above assumes the electrician's hands, tools, and test leads are safe from unexpected re-energization. Confirming zero energy is itself a test-equipment task, using a voltage tester or multimeter — the instrument category covered in depth in the next section.
Looking Ahead: Insulation-Resistance Testing
One PM and troubleshooting task deserves a preview here because it threads through this entire chapter: insulation-resistance testing, commonly performed with an instrument called a megohmmeter (or megger). In brief, a megohmmeter applies a DC test voltage across a conductor's insulation and measures the tiny leakage current that results, converting it into a resistance reading in megohms. Healthy insulation reads high; a degraded, contaminated, or moisture-affected insulation system reads low. Section 7.2 covers how this instrument — along with the multimeter, clamp meter, wattmeter, and phase-sequence tester — actually works and how it is used safely in the field.