Study guide

3.2 Mine Loading, Haulage & Materials Handling Systems

PRC Mining Engineer Licensure Examination Philippines

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Surface Mining Methods & Pit Optimization

1.1 Surface Mining Unit Operations & Method Selection 1.2 Bench Geometry, Slope Stability & Geotechnical Pit Design 1.3 Cut-Off Grade Optimization & Lerchs-Grossmann Pit Limits

2 Chapter 2: Underground Mining Methods & Strata Control

2.1 Underground Mining Method Classification & Selection 2.2 Rock Mechanics, Stress Analysis & Strata Control 2.3 Underground Ground Support Systems & Excavation Design

3 Chapter 3: Materials Handling, Equipment & Mine Economics

3.1 Drilling, Blasting & Explosives Engineering 3.2 Mine Loading, Haulage & Materials Handling Systems 3.3 Mine Capital (CAPEX), Operating Costs (OPEX) & Financial Evaluation

4 Chapter 4: Mine Safety, Ventilation & Philippine Mining Laws

4.1 Mine Ventilation Network Analysis & Environmental Quality 4.2 Philippine Mine Safety Rules, Health & Disaster Prevention 4.3 Philippine Mining Act of 1995 (RA 7942), DAO 2010-21 & Mining Ethics

5 Chapter 5: Physical Geology, Mineralogy & Philippine Deposit Types

5.1 Structural Geology, Tectonics & Ore Controls 5.2 Igneous, Metamorphic & Sedimentary Ore Mineralogy 5.3 Major Philippine Ore Deposit Models

6 Chapter 6: Mineral Exploration, Geophysics & Core Logging

6.1 Geochemical & Remote Sensing Exploration Techniques 6.2 Geophysical Exploration Methods in Mining Geology 6.3 Diamond Drilling, Core Logging & QA/QC Protocols

7 Chapter 7: Geostatistics, Resource Estimation & PMRC Code

7.1 Ore Body Block Modeling & Spatial Variography 7.2 Inverse Distance & Ordinary Kriging Grade Estimation 7.3 Philippine Mineral Reporting Code (PMRC 2020) & Resource Classification

8 Chapter 8: Comminution, Sizing & Physical Mineral Separation

8.1 Crushing, Grinding & Bond Work Index Calculations 8.2 Particle Screening, Hydrocyclone Classification & Sizing 8.3 Gravity Concentration & Magnetic/Electrostatic Separation

9 Chapter 9: Froth Flotation & Extractive Hydrometallurgy

9.1 Froth Flotation Chemistry, Reagents & Cell Kinetics 9.2 Leaching Technologies (Heap, Agitation & Tank) 9.3 Precious Metal Recovery: CIP, CIL, Merrill-Crowe & Electrowinning

10 Chapter 10: Process Plant Flowsheets & Environmental Tailings Management

10.1 Metallurgical Plant Flowsheets & Pulp Mass Balances 10.2 Tailings Storage Facility (TSF) Design & Dam Safety 10.3 Acid Mine Drainage (AMD) Mitigation & Environmental Protection (EPEP/FMR/DP)

11 Chapter 11: 2025 PRC Blueprint, Prospecting Tools & Exploration Decisions

11.1 Official 2025 TOS, Three-Paper Structure & Exam Strategy 11.2 Prospecting Instruments, Base Maps & Surface Geological Mapping 11.3 Integrating Direct and Indirect Evidence for Exploration Decisions

12 Chapter 12: Mine Infrastructure, Sustainable Development & Climate

12.1 Power, Water, Drainage & Support-Facility Selection 12.2 Sustainable Development, Progressive Rehabilitation & Community Impact 12.3 Mining, Climate, Reforestation, Coal & Energy-Transition Minerals

13 Chapter 13: Mine Valuation, Financial Analysis & Due Diligence

13.1 Time Value of Money, Future Value & Present Value 13.2 Financial Statements, Mine Economics & External Price Drivers 13.3 Exploration Provenance, Technical Review & Legal Due Diligence

14 Chapter 14: Mine Organization, Communication & Accountable Leadership

14.1 Line and Staff Functions in a Mining Organization 14.2 Communication With Superiors, Peers & Subordinates 14.3 Authority, Responsibility, Delegation & Safety Accountability

15 Chapter 15: Philippine Mining Law, Indigenous Rights & Professional Ethics

15.1 Legal Hierarchy, Mineral Tenure & Compliance Analysis 15.2 Constitutional Participation, IPRA, FPIC & Ancestral Domains 15.3 RA 4274, Professional Scope, Ethics & Document Integrity

16 Chapter 16: Applied Mathematics & Mine Surveying

16.1 Engineering Mathematics for Safe, Efficient Mine Decisions 16.2 Survey Control, Instruments, Traverses & Error Adjustment 16.3 Topographic Maps, Underground Set-Out & Survey Timeliness

17 Chapter 17: Feasibility Studies, Data Quality & Project Decisions

17.1 Scoping, Pre-Feasibility & Final Feasibility Study Maturity 17.2 Data Accuracy, Assumption Control & Go/No-Go Decisions 17.3 Multidisciplinary Integration, Interfaces & Independent Review

18 Chapter 18: Mining Computer Applications, Digital Control & Global Developments

18.1 Computer Functions, Office Applications & Data Governance 18.2 Geological Modeling, Mine Planning, Scheduling & Valuation Software 18.3 Real-Time Control, Critical Minerals & Regional Mining Developments

19 Chapter 19: Earth Systems, Geologic Time & Philippine Hazards

19.1 Solar-System Origin, Earth Interior & Atmospheric Layers 19.2 Rock Cycle, Landforms & the Geologic Time Scale 19.3 Philippine Tectonics, Geologic Hazards & Mitigation

20 Chapter 20: Metallurgy, Foundry Practice & Assaying

20.1 Extractive, Physical & Adaptive Metallurgy Principles 20.2 Foundry Materials, Casting, Solidification & Defects 20.3 Sampling, Fire Assay, Cupellation, Parting & Assay Calculations

21 Chapter 21: Solid–Liquid Separation, Environmental Law & Mine Ecology

21.1 Thickening, Filtration & Solid–Liquid Separation 21.2 Philippine Air, Water, Waste & Hazardous-Substance Controls 21.3 Mine Ecology, Closure, Tailings, Waste & Community Livelihood

3.2 Mine Loading, Haulage & Materials Handling Systems

Key Takeaways Explain This Topic AI

Loading choices include hydraulic excavators, electric rope shovels, wheel loaders, and underground LHD units; capacity, mobility, power, digging conditions, selectivity, availability, and life-cycle cost determine the fit.

Haulage systems bridge open-pit and underground production faces to crushers/waste dumps, employing rigid dump trucks (off-highway 90–360+ tonne payload), articulated dump trucks (ADT for soft/steep ground), continuous belt conveyors, and shaft skip hoisting systems.

A deterministic Match Factor of 1.0 balances nominal truck and loader cycle capacity, but stochastic travel, spotting, loading, delays, bunching, and availability still create queues and idle time.

Total hauling resistance is the sum of Rolling Resistance (RR, 1.5–2.0% for paved haul roads up to 8–12% for soft mud) and Grade Resistance (GR, 1% per 1% grade rise/fall), dictating total effective grade and vehicle rimpull requirements.

Vehicle rimpull curves define maximum usable tractive effort based on engine horsepower, gear ratios, speed, and coefficient of traction (mu), preventing wheel slip while maintaining maximum gradeability.

Last updated: August 2026

3.2 Mine Loading, Haulage & Materials Handling Systems

Materials handling represents the single largest operational expenditure in open-pit and underground mining operations, frequently accounting for 45% to 60% of total mine operating costs. Selecting, matching, and optimizing loading and transport systems determines overall mine productivity and unit cost efficiency.

1. Primary Surface & Underground Loading Equipment

Loading equipment excavates fragmented rock from the bench face or muckpile and loads it into haulage units or crushers:

Electric Rope Shovels : High-capacity loading units utilizing wire ropes and rack-and-pinion crowd mechanisms. Equipped with bucket capacities exceeding 30 to 60 m³ (50 to 100+ tonnes per pass), rope shovels can offer low unit loading cost and long service in high-tonnage, long-life mines, subject to utilization, power, mobility, maintenance, and life-cycle economics.

Hydraulic Mining Excavators : Available in front-shovel and backhoe configurations with dipper capacities up to 45 m³. Front shovels break out rock above track level with high crowd force, while backhoes dig effectively below track grade. Hydraulic shovels feature higher mobility and selective digging capabilities compared to electric rope shovels.

Front-End Wheel Loaders (FEL) : Highly mobile rubber-tired loaders used for primary loading in lower-tonnage pits, stockpile rehandling, and auxiliary cleanup around primary shovels.

Load-Haul-Dump (LHD) Units : Specialized low-profile diesel or electric underground vehicles designed to scoop ore from stopes or drawpoints, tram across underground drifts, and dump into ore passes, trucks, or underground crushers.

2. Mine Haulage Fleet Configurations

Haulage transports fragmented material from loading faces to destination points (primary crusher, waste dumps, tailings facilities, or stockpiles):

Off-Highway Rigid Dump Trucks : Rear-dump trucks ranging from 90 to 400 tonnes payload capacity. Available in mechanical drive (engine-transmission-driveline) and diesel-electric drive (engine-generator-wheel electric motors). Rigid dump trucks dominate well-maintained, heavy surface mining operations.

Articulated Dump Trucks (ADT) : Feature an articulated frame joint and all-wheel drive for payloads of 25 to 55 tonnes. ADTs excel on steep ramps, soft underfoot conditions, and narrow haul roads where rigid trucks lose traction.

Underground Haul Trucks : Low-profile, heavy-duty rear-dump trucks (20 to 60 tonnes payload) designed for tight clearance in underground haulage drifts and ramps.

3. Continuous & Shaft Materials Handling

Belt Conveyors : Continuous transportation systems offering significantly lower unit operating costs than truck haulage for long-distance, high-volume material movement. In-Pit Crushing and Conveying (IPCC) systems crush run-of-mine (ROM) ore directly in the pit, substituting trucks with overland belt conveyors.

Shaft Skip Hoisting : In deep underground mines, ore is elevated to the surface via hoisting systems. Skip hoists carry broken ore in guided steel skips driven by friction (Koepe) or drum hoists mounted in surface headframes. Skip hoisting capacity is calculated from skip payload ( L s L_s L s ​ ), velocity ( v v v ), hoist acceleration/deceleration, and loading/dumping dwell times.

4. Equipment Cycle Time Mechanics

Total loading and haulage productivity depends on individual equipment cycle times.

Loader Cycle Time ( t l t_l t l ​ ) : t l = t dig + t swing loaded + t dump + t swing empty t_l = t_{\text{dig}} + t_{\text{swing loaded}} + t_{\text{dump}} + t_{\text{swing empty}} t l ​ = t dig ​ + t swing loaded ​ + t dump ​ + t swing empty ​ Typical shovel cycle times range from 25 to 40 seconds per pass.

Truck Haul Cycle Time ( t c t_c t c ​ ) : t c = t spot load + t loading + t haul loaded + t spot dump + t dumping + t return empty t_c = t_{\text{spot load}} + t_{\text{loading}} + t_{\text{haul loaded}} + t_{\text{spot dump}} + t_{\text{dumping}} + t_{\text{return empty}} t c ​ = t spot load ​ + t loading ​ + t haul loaded ​ + t spot dump ​ + t dumping ​ + t return empty ​ where t loading = n passes × t l t_{\text{loading}} = n_{\text{passes}} \times t_l t loading ​ = n passes ​ × t l ​ .

Equipment availability ( A = Operating Hours Scheduled Hours A = \frac{\text{Operating Hours}}{\text{Scheduled Hours}} A = Scheduled Hours Operating Hours ​ ) and utilization ( U = Actual Operating Hours Available Hours U = \frac{\text{Actual Operating Hours}}{\text{Available Hours}} U = Available Hours Actual Operating Hours ​ ) scale nominal fleet capacity to net operating production.

5. Shovel-Truck Match Factor & Fleet Sizing

The Match Factor ( M F MF MF ) measures the operational balance between the loading fleet and haul truck fleet: M F = N t ⋅ t l N l ⋅ t c MF = \frac{N_t \cdot t_l}{N_l \cdot t_c} MF = N l ​ ⋅ t c ​ N t ​ ⋅ t l ​ ​

where N t N_t N t ​ is number of active haul trucks, N l N_l N l ​ is number of active loading units, t l t_l t l ​ is time required by one loader to load one truck ( n passes × t pass n_{\text{passes}} \times t_{\text{pass}} n passes ​ × t pass ​ ), and t c t_c t c ​ is total truck cycle time.

Operational interpretations:

M F < 1.0 MF < 1.0 MF < 1.0 (Under-trucked) : Shovels experience idle time waiting for trucks; truck capacity is nominally in demand while loading capacity is underused in the deterministic model.

M F = 1.0 MF = 1.0 MF = 1.0 (Perfect Match) : Total loading capacity equals total truck transport capacity.

M F > 1.0 MF > 1.0 MF > 1.0 (Over-trucked) : Trucks queue at the loader waiting to be filled; loading capacity is nominally in demand while trucks queue in the deterministic model.

6. Haul Road Resistance Fundamentals

Total vehicle resistance ( T R TR TR ) determines the engine power required for a truck to maintain speed up a haul road ramp. Total resistance is expressed as an equivalent grade percentage ( T R = R R + G R TR = RR + GR TR = RR + GR ):

Rolling Resistance ( R R RR RR ) : Resistance caused by tire internal flexing and ground penetration under vehicle weight. Expressed as: R R = R R base + 0.6 % × ( tire penetration in cm ) RR = RR_{\text{base}} + 0.6\% \times (\text{tire penetration in cm}) RR = R R base ​ + 0.6% × ( tire penetration in cm ) Typical R R RR RR values:

  • Hard, smooth asphalt/concrete: 1.5% to 2.0%
  • Well-maintained compacted gravel haul road: 2.5% to 3.0%
  • Soft, uncompacted earth or rutted mud: 8.0% to 12.0%+

Grade Resistance ( G R GR GR ) : Gravitational resistance encountered when traversing inclines. G R GR GR equals the physical road grade percentage directly ( G R = Grade % GR = \text{Grade \%} GR = Grade % ). For downhill travel, grade resistance becomes Grade Assistance (subtracted from R R RR RR ).

For example, a truck ascending an 8% haul road ramp with a 3% rolling resistance experiences a Total Equivalent Grade Resistance of T R = 3 % + 8 % = 11 % TR = 3\% + 8\% = 11\% TR = 3% + 8% = 11% .

7. Vehicle Rimpull & Gradeability Performance

Rimpull is the tractive force (in kN or lbs) available between the driving tires and the road surface to overcome total resistance: Rimpull (lbs) = 375 × H P × η V (mph) \text{Rimpull (lbs)} = \frac{375 \times HP \times \eta}{V \text{ (mph)}} Rimpull (lbs) = V (mph) 375 × H P × η ​

where H P HP H P is engine horsepower, η \eta η is mechanical driveline efficiency (~80–85%), and V V V is vehicle speed.

The maximum usable rimpull is limited by the coefficient of traction ( μ \mu μ ) between tire and road surface before wheel slippage occurs: Rimpull usable = W drive weight × μ \text{Rimpull}_{\text{usable}} = W_{\text{drive weight}} \times \mu Rimpull usable ​ = W drive weight ​ × μ

Engine rimpull curves plot available force against vehicle speed across transmission gears. When T R TR TR is expressed as a percent, engineers calculate required force as ( T R / 100 ) × Gross Vehicle Weight (TR/100) \times \text{Gross Vehicle Weight} ( TR /100 ) × Gross Vehicle Weight and compare it with the performance curves to determine maximum sustainable speed and gear range for any ramp section.