Study guide

6.3 Diamond Drilling, Core Logging & QA/QC Protocols

PRC Mining Engineer Licensure Examination Philippines

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Surface Mining Methods & Pit Optimization

1.1 Surface Mining Unit Operations & Method Selection 1.2 Bench Geometry, Slope Stability & Geotechnical Pit Design 1.3 Cut-Off Grade Optimization & Lerchs-Grossmann Pit Limits

2 Chapter 2: Underground Mining Methods & Strata Control

2.1 Underground Mining Method Classification & Selection 2.2 Rock Mechanics, Stress Analysis & Strata Control 2.3 Underground Ground Support Systems & Excavation Design

3 Chapter 3: Materials Handling, Equipment & Mine Economics

3.1 Drilling, Blasting & Explosives Engineering 3.2 Mine Loading, Haulage & Materials Handling Systems 3.3 Mine Capital (CAPEX), Operating Costs (OPEX) & Financial Evaluation

4 Chapter 4: Mine Safety, Ventilation & Philippine Mining Laws

4.1 Mine Ventilation Network Analysis & Environmental Quality 4.2 Philippine Mine Safety Rules, Health & Disaster Prevention 4.3 Philippine Mining Act of 1995 (RA 7942), DAO 2010-21 & Mining Ethics

5 Chapter 5: Physical Geology, Mineralogy & Philippine Deposit Types

5.1 Structural Geology, Tectonics & Ore Controls 5.2 Igneous, Metamorphic & Sedimentary Ore Mineralogy 5.3 Major Philippine Ore Deposit Models

6 Chapter 6: Mineral Exploration, Geophysics & Core Logging

6.1 Geochemical & Remote Sensing Exploration Techniques 6.2 Geophysical Exploration Methods in Mining Geology 6.3 Diamond Drilling, Core Logging & QA/QC Protocols

7 Chapter 7: Geostatistics, Resource Estimation & PMRC Code

7.1 Ore Body Block Modeling & Spatial Variography 7.2 Inverse Distance & Ordinary Kriging Grade Estimation 7.3 Philippine Mineral Reporting Code (PMRC 2020) & Resource Classification

8 Chapter 8: Comminution, Sizing & Physical Mineral Separation

8.1 Crushing, Grinding & Bond Work Index Calculations 8.2 Particle Screening, Hydrocyclone Classification & Sizing 8.3 Gravity Concentration & Magnetic/Electrostatic Separation

9 Chapter 9: Froth Flotation & Extractive Hydrometallurgy

9.1 Froth Flotation Chemistry, Reagents & Cell Kinetics 9.2 Leaching Technologies (Heap, Agitation & Tank) 9.3 Precious Metal Recovery: CIP, CIL, Merrill-Crowe & Electrowinning

10 Chapter 10: Process Plant Flowsheets & Environmental Tailings Management

10.1 Metallurgical Plant Flowsheets & Pulp Mass Balances 10.2 Tailings Storage Facility (TSF) Design & Dam Safety 10.3 Acid Mine Drainage (AMD) Mitigation & Environmental Protection (EPEP/FMR/DP)

11 Chapter 11: 2025 PRC Blueprint, Prospecting Tools & Exploration Decisions

11.1 Official 2025 TOS, Three-Paper Structure & Exam Strategy 11.2 Prospecting Instruments, Base Maps & Surface Geological Mapping 11.3 Integrating Direct and Indirect Evidence for Exploration Decisions

12 Chapter 12: Mine Infrastructure, Sustainable Development & Climate

12.1 Power, Water, Drainage & Support-Facility Selection 12.2 Sustainable Development, Progressive Rehabilitation & Community Impact 12.3 Mining, Climate, Reforestation, Coal & Energy-Transition Minerals

13 Chapter 13: Mine Valuation, Financial Analysis & Due Diligence

13.1 Time Value of Money, Future Value & Present Value 13.2 Financial Statements, Mine Economics & External Price Drivers 13.3 Exploration Provenance, Technical Review & Legal Due Diligence

14 Chapter 14: Mine Organization, Communication & Accountable Leadership

14.1 Line and Staff Functions in a Mining Organization 14.2 Communication With Superiors, Peers & Subordinates 14.3 Authority, Responsibility, Delegation & Safety Accountability

15 Chapter 15: Philippine Mining Law, Indigenous Rights & Professional Ethics

15.1 Legal Hierarchy, Mineral Tenure & Compliance Analysis 15.2 Constitutional Participation, IPRA, FPIC & Ancestral Domains 15.3 RA 4274, Professional Scope, Ethics & Document Integrity

16 Chapter 16: Applied Mathematics & Mine Surveying

16.1 Engineering Mathematics for Safe, Efficient Mine Decisions 16.2 Survey Control, Instruments, Traverses & Error Adjustment 16.3 Topographic Maps, Underground Set-Out & Survey Timeliness

17 Chapter 17: Feasibility Studies, Data Quality & Project Decisions

17.1 Scoping, Pre-Feasibility & Final Feasibility Study Maturity 17.2 Data Accuracy, Assumption Control & Go/No-Go Decisions 17.3 Multidisciplinary Integration, Interfaces & Independent Review

18 Chapter 18: Mining Computer Applications, Digital Control & Global Developments

18.1 Computer Functions, Office Applications & Data Governance 18.2 Geological Modeling, Mine Planning, Scheduling & Valuation Software 18.3 Real-Time Control, Critical Minerals & Regional Mining Developments

19 Chapter 19: Earth Systems, Geologic Time & Philippine Hazards

19.1 Solar-System Origin, Earth Interior & Atmospheric Layers 19.2 Rock Cycle, Landforms & the Geologic Time Scale 19.3 Philippine Tectonics, Geologic Hazards & Mitigation

20 Chapter 20: Metallurgy, Foundry Practice & Assaying

20.1 Extractive, Physical & Adaptive Metallurgy Principles 20.2 Foundry Materials, Casting, Solidification & Defects 20.3 Sampling, Fire Assay, Cupellation, Parting & Assay Calculations

21 Chapter 21: Solid–Liquid Separation, Environmental Law & Mine Ecology

21.1 Thickening, Filtration & Solid–Liquid Separation 21.2 Philippine Air, Water, Waste & Hazardous-Substance Controls 21.3 Mine Ecology, Closure, Tailings, Waste & Community Livelihood

6.3 Diamond Drilling, Core Logging & QA/QC Protocols

Key Takeaways Explain This Topic AI

Diamond core drilling delivers continuous cylindrical rock samples in standardized sizes (PQ: 85.0 mm, HQ: 63.5 mm, NQ: 47.6 mm) for structural, geological, and geotechnical logging.

Core recovery percentage (% Recovery = [Total Length of Recovered Core / Drill Run Length] × 100) quantifies physical sample loss during drilling.

Rock Quality Designation (RQD = [∑ Length of Sound Core Pieces ≥ 10 cm / Drill Run Length] × 100) measures rock mass jointing and structural competence.

Reverse Circulation (RC) drilling provides rapid, cost-effective rock chip sampling for grade control and infill drilling, though it lacks continuous structural core orientation.

QA/QC programs use fit-for-purpose CRMs, blanks, field/coarse/pulp duplicates, checks, and umpire work; insertion rates, control rules, precision statistics, and corrective actions are risk- and method-specific rather than one mandated percentage.

Last updated: August 2026

Exploration drilling provides physical subsurface samples required for geological modeling, geomechanical evaluations, and mineral resource estimation. To convert raw drill core into compliant mineral resource estimates under the Philippine Mineral Reporting Code (PMRC) or JORC code, exploration companies must execute rigorous core recovery procedures, standardized geological and geotechnical logging, and robust Quality Assurance / Quality Control (QA/QC) protocols.

Exploration Drilling Methodologies

The two primary drilling methods utilized in mineral exploration are Diamond Core Drilling (DDH) and Reverse Circulation (RC) drilling.

1. Diamond Core Drilling (DDH)

Diamond drilling utilizes a hollow, diamond-impregnated drill bit attached to rotating drill rods to cut a continuous cylindrical core of solid rock. Wireline core retrieval systems allow the inner core barrel containing the sample to be hoisted to the surface through the drill string without pulling the entire drill rod assembly.

Standard Wireline Core Diameters :

PQ Core : 85.0 mm 85.0\text{ mm} 85.0 mm core diameter ( 122.6 mm 122.6\text{ mm} 122.6 mm hole diameter). Preferred for highly fractured ground, weathered saprolite, and metallurgical bulk sampling.

HQ Core : 63.5 mm 63.5\text{ mm} 63.5 mm core diameter ( 96.0 mm 96.0\text{ mm} 96.0 mm hole diameter). Standard size for detailed resource definition drilling.

NQ Core : 47.6 mm 47.6\text{ mm} 47.6 mm core diameter ( 75.7 mm 75.7\text{ mm} 75.7 mm hole diameter). Applied in deep exploration holes ( > 500 m > 500\text{ m} > 500 m ) or tight budget scout drilling.

Triple Tube Barrel Systems (HQ3 / NQ3) : Incorporates a split inner tube inside the barrel to preserve friable, soft, or highly fractured rock cores without mechanical disturbance during extraction.

2. Reverse Circulation (RC) Drilling

RC drilling utilizes a dual-wall drill pipe and a pneumatic hammer bit. Compressed air is forced down the outer annulus of the drill string, driving the hammer and blowing rock cuttings upward through the center inner tube to a cyclone separator at the surface.

Advantages : Rapid penetration rates ( 100 – 200 m/day 100\text{--}200\text{ m/day} 100 – 200 m/day ), lower cost per meter, and elimination of sample cross-contamination.

Limitations : Produces fine rock chips rather than intact core; cannot provide structural orientation measurements for fault or vein dip analysis.

Core Recovery & Rock Quality Designation (RQD)

Before geological logging, geotechnical engineers measure Core Recovery and calculate Rock Quality Designation (RQD) over each drill run (typically 1.5 m 1.5\text{ m} 1.5 m or 3.0 m 3.0\text{ m} 3.0 m ).

1. Core Recovery Percentage ( C R % CR\% CR % )

Core Recovery quantifies the percentage of intact rock length recovered relative to the total length of the drill run: Core Recovery ( C R % ) = ( ∑ L recovered L run ) × 100 % \text{Core Recovery } (CR\%) = \left( \frac{\sum L_{\text{recovered}}}{L_{\text{run}}} \right) \times 100\% Core Recovery ( CR % ) = ( L run ​ ∑ L recovered ​ ​ ) × 100%

Where ∑ L recovered \sum L_{\text{recovered}} ∑ L recovered ​ is the total cumulative length of all recovered core pieces laid end-to-end in the core trough, and L run L_{\text{run}} L run ​ is the length drilled (e.g., 3.0 m 3.0\text{ m} 3.0 m ). Core recovery below 95 % 95\% 95% indicates core loss in crushed fault zones or soluble horizons, which can introduce sampling bias into grade calculations.

2. Rock Quality Designation ( R Q D % RQD\% RQ D % )

Developed by Deere (1964), RQD measures the structural soundness and joint spacing of the rock mass: R Q D % = ( ∑ L ∑ L sound pieces ≥ 10 cm L run ) × 100 % RQD\% = \left( \frac{\sum L_{\sum L_{\text{sound pieces } \ge 10\text{ cm}}}}{L_{\text{run}}} \right) \times 100\% RQ D % = ( L run ​ ∑ L ∑ L sound pieces ≥ 10 cm ​ ​ ​ ) × 100%

Measurement Rules:

Sum only hard, sound core pieces that are 10 cm 10\text{ cm} 10 cm (4 inches) or longer measured along the core centerline.

Mechanical Breaks : Fractures clearly caused by drilling, core handling, or box packing must be fitted back together and counted as single, unbroken sound pieces.

Soft, highly weathered rock pieces that crumble by hand are assigned a length of zero regardless of physical length.

Geomechanical Classification Table:

  • RQD Range (%) Rock Mass Quality Description Expected Structural Competence
  • 0 – 25% Very Poor Highly fractured, sheared, or intensely weathered
  • 25 – 50% Poor Closely jointed rock mass
  • 50 – 75% Fair Moderately jointed, medium block size
  • 75 – 90% Good Widely jointed, competent rock
  • 90 – 100% Excellent Massive, unjointed rock mass
  • Geological & Geotechnical Core Logging

Core logging systematically records geological, structural, and geotechnical observations into standardized digital databases.

1. Geological Logging Parameters

Lithology : Primary rock type, igneous texture, sedimentary bedding, or metamorphic fabric.

Alteration : Hydrothermal mineral assemblies (e.g., potassic, phyllic, argillic, propylitic) and alteration intensity (weak, moderate, intense, pervasive).

Mineralization : Ore mineral species (chalcopyrite, bornite, galena, sphalerite, native gold), vein textures (crustiform, comb, stockwork, breccia), and visual percentage estimates.

Structural Orientation : Measuring alpha ( α \alpha α ) and beta ( β \beta β ) angles of planar structures (veins, faults, joints) on oriented core marked with a bottom-of-hole ellipse line.

2. Geotechnical Logging & Core Splitting

Geotechnical Parameters : Record Joint Roughness Number ( J r J_r J r ​ ), Joint Alteration Number ( J a J_a J a ​ ), Fracture Frequency per meter ( F F / m FF/m FF / m ), and Point Load Index ( I s ( 50 ) I_{s(50)} I s ( 50 ) ​ ) for Rock Mass Rating (RMR) and Q-system slope stability designs.

Core Splitting : Intact drill core is cut longitudinally using an automated diamond wire saw. One half-core is bagged for laboratory assay, while the remaining half-core is permanently retained in wooden or plastic core trays as an archival reference.

Quality Assurance & Quality Control (QA/QC) Protocols

QA/QC programs test sampling precision, preparation contamination, analytical accuracy, and laboratory precision. PMRC/JORC-style reporting requires the Competent Person to establish and disclose fit-for-purpose quality controls, but it does not prescribe one universal 15%–20% insertion rate or one set of control limits. Frequency and placement follow commodity, grade range, nugget effect, batch size, laboratory risk, decision consequence, and prior performance.

1. Control Sample Types and Objectives

Certified Reference Materials (CRMs) : Matrix- and concentration-appropriate materials test analytical accuracy. Plot results against certified values and uncertainty. Define warning, failure, affected-batch, investigation, and release rules before results arrive; one 3 σ 3\sigma 3 σ or two same-side 2 σ 2\sigma 2 σ results is a common project rule, not a reporting-code command.

Blanks : Material with concentrations suitably below the decision level tests contamination during crushing, pulverizing, and analysis. Insert blanks at routine and strategically selected positions, including after expected high grades where this will not reveal sample identity improperly.

Field Duplicates : A second field sample or an appropriate half- or quarter-core split estimates primary sampling and short-range geological variability. The split method must preserve enough core for records and suit the mineralization.

Coarse Duplicates : Independent splits after crushing test preparation and splitting variance.

Pulp Duplicates / Laboratory Repeats : Repeat aliquots from a pulverized sample test analytical precision. A separate umpire-laboratory program uses selected pulps or rejects to assess inter-laboratory bias; it is not the definition of every pulp duplicate.

2. Statistical Precision Evaluation

Use time-ordered control charts, bias plots, paired scatterplots, absolute and relative difference, quantile plots, and duplicate precision methods suited to heteroscedastic data. Investigate trends by batch, grade, material, instrument, and laboratory. Fixed RPD limits can be misleading near detection limits or in nuggety mineralization, so acceptance criteria must be justified from fitness for purpose rather than copied from a generic table.