Study guide

1.2 X-Ray Tube Components, Target Interactions & Emission Spectrum

Philippine Radiologic Technologists Licensure Examination Exam

Track your progress as you read

Finished sections get a check mark.

1 Subject 1, Chapter 1: Physics of Radiology & X-Ray Production

1.1 Atomic Structure, Electromagnetic Spectrum & X-Ray Production Mechanisms 1.2 X-Ray Tube Components, Target Interactions & Emission Spectrum 1.3 Photon Interactions with Matter: Photoelectric, Compton, Coherent & Pair Production

2 Subject 1, Chapter 2: Radiographic Equipment & Circuitry

2.1 High-Voltage Generators, Transformers & Rectification Circuits 2.2 Automatic Exposure Control (AEC), Beam Restriction & Quality Control 2.3 Tube Rating Charts, Extending Tube Life, Mechanical Malfunction & Preventive Maintenance

3 Subject 1, Chapter 3: Radiobiology & Cellular Response

3.1 Radiation Interaction with Tissue, Direct/Indirect Action & LET/RBE 3.2 Law of Bergonie & Tribondeau, Deterministic vs. Stochastic Effects 3.3 Dose-Response Relationships, Embryo and Fetal Effects & Acute Radiation Syndrome

4 Subject 1, Chapter 4: Radiation Protection & Dose Limits

4.1 ALARA Principles, Structural Shielding & Dose Limits 4.2 Personnel Dosimetry & Patient Dose Reduction Techniques 4.3 Dose Calculation Problems: Time, Distance, Shielding & Structural Barrier Design

5 Subject 1, Chapter 5: Imaging Informatics & Quality Assurance

5.1 PACS Architecture, DICOM Standards & HL7 Integration 5.2 Quality Assurance & Quality Control Protocols in Diagnostic Radiography 5.3 Radiology Workflow, RIS/HIS Integration, Teleradiology & Informatics Quality Assurance

6 Subject 2, Chapter 6: Film-Screen Radiography & Sensitometry

6.1 Film Emulsion, Latent Image Formation & Darkroom Chemistry 6.2 Sensitometric Curve (H&D Curve), Film Speed & Contrast Characteristics 6.3 Radiographic Film Analysis: Processing Faults, Handling Artifacts & Corrective Measures

7 Subject 2, Chapter 7: Technical Factors & Radiographic Quality

7.1 Density/Brightness, Contrast, Spatial Resolution & Distortion Controls 7.2 Exposure Math: Inverse Square Law, 15% Rule & Grid Conversion Factors 7.3 Technique Compensation: Age, Pathology, Cast and Orthopaedic Devices, Screen Speed & Beam Restriction

8 Subject 2, Chapter 8: Computed Radiography (CR)

8.1 Photostimulable Phosphor (PSP) Plates & CR Reader Mechanics 8.2 Image Processing, CR Artifacts & Erasure Protocols

9 Subject 2, Chapter 9: Digital Radiography (DR)

9.1 Flat-Panel Detectors: Direct vs. Indirect Conversion & TFT Arrays 9.2 Detective Quantum Efficiency (DQE), Modulation Transfer Function (MTF) & Dynamic Range

10 Subject 2, Chapter 10: Exposure Indicators & Image Evaluation

10.1 Exposure Indicators (S-Number, EI, DI), Windowing & Look-Up Tables (LUT) 10.2 Image Critique Checklist, Artifact Identification & Quality Control Standards 10.3 Image Display & Hard-Copy Output: Monitor Classification, DICOM GSDF, Dry vs Wet Laser Imaging

11 Subject 3, Chapter 11: Chest, Abdomen & Routine Positioning Concepts

11.1 Anatomical Terminology, Body Planes & Chest Radiography (PA, Lateral, Decubitus) 11.2 Abdominal Radiography: Acute Abdomen Series & Erect/Supine Protocols 11.3 Radiologic Surface Anatomy, Body Habitus & Sectional Body Cuts

12 Subject 3, Chapter 12: Upper & Lower Extremities & Girdles

12.1 Upper Limb & Shoulder Girdle Positioning (Hand, Wrist, Forearm, Elbow, Humerus, Shoulder) 12.2 Lower Limb & Pelvic Girdle Positioning (Foot, Ankle, Leg, Knee, Femur, Pelvis, Hip)

13 Subject 3, Chapter 13: Spine & Bony Thorax

13.1 Cervical, Thoracic & Lumbar Spine Radiography & Trauma Adaptations 13.2 Sacrum, Coccyx, Sacroiliac Joints & Bony Thorax (Ribs & Sternum)

14 Subject 3, Chapter 14: Cranium, Facial Bones & Paranasal Sinuses

14.1 Skull Positioning: Towne, Caldwell, Lateral & SMV Projections 14.2 Facial Bones, Orbits, Zygomatic Arches & Paranasal Sinuses

15 Subject 3, Chapter 15: Contrast Media Studies & Special Procedures

15.1 Gastrointestinal Contrast Procedures (Esophagram, UGI, Small Bowel, Barium Enema) 15.2 Genitourinary, Biliary & Special Fluoroscopic Studies (IVU, Cystography, ERCP, Myelography) 15.3 Reproductive System Studies: Hysterosalpingography, Pelvimetry & Male Reproductive Procedures 15.4 Nasopharyngography, Sialography & Fistulography / Sinus Tract Visualization

16 Subject 4, Chapter 16: Human Anatomy, Physiology & Pathology Integration

16.1 Body System Anatomy & Systemic Physiology Overview for Radiographers 16.2 Radiologic Pathology: Image Manifestations of Neoplastic, Inflammatory & Traumatic Conditions

17 Subject 4, Chapter 17: Patient Assessment, Communication & Informed Consent

17.1 Professional Communication, History Taking & Patient Rights 17.2 Informed Consent, Medical Documentation & Patient Transfer Safety

18 Subject 4, Chapter 18: Infection Control & Vital Signs Monitoring

18.1 Standard Precautions, Asepsis, Sterilization & Isolation Protocols 18.2 Measurement & Assessment of Vital Signs (BP, Pulse, Respiration, Temperature)

19 Subject 4, Chapter 19: Emergency Care & Aseptic Venipuncture

19.1 Basic Life Support (BLS), CPR Concepts & Emergency Response in Radiology 19.2 Aseptic Venipuncture Technique, IV Maintenance & Extravasation Care

20 Subject 4, Chapter 20: Professional Ethics, Jurisprudence & RA 7431

20.1 Republic Act No. 7431 (Radiologic Technology Act of 1992) & Board Rules 20.2 Code of Professional Ethics, Legal Liabilities, Malpractice & Negligence 20.3 Bioethical Principles in Practice, Professional Virtues & Interprofessional Relationships

21 Subject 5, Chapter 21: Diagnostic Ultrasonography

21.1 Ultrasound Physics, Transducer Construction & Doppler Principles 21.2 Acoustic Artifacts, Clinical Applications & Safety (TI/MI) 21.3 Clinical Ultrasound Examinations: Indications, Patient Preparation, Scanning Protocols & Transducer Selection

22 Subject 5, Chapter 22: Computed Tomography (CT)

22.1 CT Physics, Gantry Components, Detectors & Helical/Multislice Acquisition 22.2 Hounsfield Units, Windowing, CT Artifacts & Radiation Dose (CTDI/DLP)

23 Subject 5, Chapter 23: Magnetic Resonance Imaging (MRI)

23.1 MRI Physics, Nuclear Spin, T1/T2 Relaxation & Pulse Sequences 23.2 MRI Safety (Zones I-IV, SAR, Metallic Implants) & Common Artifacts 23.3 MRI Examination Protocols, Patient Preparation, Gadolinium Contrast & Sectional MRI Anatomy

24 Subject 5, Chapter 24: Interventional Radiology & Vascular Imaging

24.1 Vascular Access, Seldinger Technique & Digital Subtraction Angiography (DSA) 24.2 Interventional Procedures (Embolization, Angioplasty, Stenting) & C-Arm Radiation Safety 24.3 Interventional Patient Management: Contrast Selection, Pre-Procedure Workup & Post-Procedure Care

25 Subject 5, Chapter 25: Contrast Media Pharmacology & Adverse Reactions

25.1 Classification of Contrast Agents: Osmolality, Viscosity & Iodine Concentration 25.2 Adverse Contrast Reactions (Mild, Moderate, Severe) & Emergency Treatment Protocols 25.3 General Pharmacologic Principles: Pharmacokinetics, Pharmacodynamics, Drug Categories & the Rights of Drug Safety

26 Subject 5, Chapter 26: Nuclear Medicine & Molecular Imaging

26.1 Radioisotopes, Radiopharmaceuticals & Gamma Camera / SPECT Operation 26.2 Positron Emission Tomography (PET/CT) & Unsealed Radiation Source Safety

27 Subject 5, Chapter 27: Radiation Therapy & Radiation Oncology

27.1 Principles of Radiation Oncology, Linear Accelerators & Treatment Planning 27.2 Teletherapy vs. Brachytherapy, Patient Immobilization & Side Effect Management 27.3 Isodose Planning, Treatment Delivery Methods & Radiobiologic Principles in Radiation Therapy

28 Mammography & Dental Radiography

28.1 Mammography: Equipment, CC and MLO Positioning, Compression & Breast Pathology 28.2 Dental Radiography: Paralleling and Bisecting Techniques, Bitewing, Occlusal, Panoramic & Cephalometric

29 Medical Terminology for Radiologic Technology

29.1 Medical Word Building: Root Words, Combining Forms, Prefixes & Suffixes 29.2 Medical Terms in General Medicine, Abbreviations, Symbols & Critiquing Requests and Reports

30 Radiology Administration, Organization & Leadership

30.1 Organizational Structure, Staffing & Licensing Requirements of a Radiology Facility 30.2 Radiology Department Management: Job Descriptions, Duties, Leadership Styles & Entrepreneurial Skills

1.2 X-Ray Tube Components, Target Interactions & Emission Spectrum

Key Takeaways Explain This Topic AI

The line-focus principle utilizes an angled target (7° to 17°) to maintain a large actual focal spot for optimal heat loading while producing a small effective focal spot for superior spatial resolution.

The anode heel effect results in up to 45% variation in beam intensity across the field, with maximum intensity located at the cathode end and reduced intensity at the anode end.

Total filtration of at least 2.5 mm Aluminum equivalent is mandatory for diagnostic X-ray tubes operating above 70 kVp to absorb low-energy photons and reduce patient skin dose.

Heat unit production is calculated using HU = kVp * mAs * generator factor, where single-phase generators use a factor of 1.0, 3-phase 6-pulse use 1.35, and 3-phase 12-pulse or high-frequency generators use 1.40.

High-frequency generators exhibit less than 1% voltage ripple, resulting in higher average photon energy, greater beam quantity, and significantly lower patient exposure compared to single-phase systems.

Last updated: August 2026

  • 1.2 X-Ray Tube Components, Target Interactions & Emission Spectrum
  • The Cathode Assembly & Thermionic Emission

The cathode is the negative electrode assembly of the diagnostic X-ray tube. Its primary functions are to produce a stream of electrons via thermionic emission and focus them toward the anode target.

Component Parts of the Cathode

Filament : A small coil of wire constructed of thoriated tungsten (tungsten alloyed with 1% to 2% thorium). Tungsten is chosen for its extremely high melting point ( 3 , 410 ∘ C 3,410^\circ\text{C} 3 , 41 0 ∘ C ) and resistance to thermal vaporization. The addition of thorium enhances thermionic emission efficiency and significantly extends tube life. Most modern diagnostic X-ray tubes feature a dual-filament cathode (dual focal spots):

Small Filament : Typically 0.5 mm to 0.6 mm in diameter. Used for high spatial resolution imaging (e.g., extremity radiographies) where fine anatomical detail is required. Restricted to lower exposure techniques (typically ≤ 200 mA \le 200\text{ mA} ≤ 200 mA ) due to concentrated heat loading.

Large Filament : Typically 1.0 mm to 1.2 mm in diameter. Used for imaging large anatomical structures (e.g., abdomen, spine) requiring high exposure factors (high mAs). Spreads heat over a larger target area.

Focusing Cup : A negatively charged nickel or stainless steel cavity in which the filaments are embedded. Because electrons carry negative electrical charges, they tend to diverge electrostatically due to mutual repulsion. The focusing cup maintains a negative electrostatic charge relative to the filament, repelling and compressing the electron cloud into a tight, narrow stream directed precisely toward the anode focal spot.

Space Charge Effect : When the filament current heats the wire to incandescence, electrons are "boiled off" in a process called thermionic emission . These electrons form a cloud around the filament known as the space charge . As space charge density increases, the cumulative negative charge repels newly emitted electrons, limiting further thermionic emission. This phenomenon is termed the space charge effect and limits tube operation at low kVp and high mA settings.

The Anode Assembly & Geometric Physics

The anode is the positive electrode assembly of the X-ray tube. It conducts electricity, provides mechanical support for the target, and serves as a thermal radiator to dissipate extreme heat.

Rotating Anode Construction

Modern general diagnostic X-ray tubes utilize a rotating anode target to prevent target melting by distributing heat over a large rotating track. The disc assembly comprises:

Target Face : A thin track composed of tungsten-rhenium alloy (90% tungsten, 10% rhenium). Rhenium provides structural elasticity to prevent target crazing, surface pitting, and cracking under thermal stress.

Base Disc : Molybdenum backed by graphite. Molybdenum has a low thermal conductivity and high melting point, preventing rapid heat transfer down the rotor shaft into the delicate copper rotor bearings. Graphite increases thermal storage capacity without adding substantial weight.

Induction Motor : Operates via electromagnetic induction without physical electrical connections inside the vacuum. It consists of:

Stator : A series of stationary electromagnets positioned outside the glass/metal envelope.

Rotor : A hollow cylinder of copper and soft iron attached to the anode molybdenum shaft inside the vacuum. Stator coils are energized sequentially, generating a rotating magnetic field that turns the rotor at standard speeds ( 3,400 rpm ) or high speeds ( 10,000 rpm for high-output procedures).

The Line-Focus Principle

The line-focus principle is a geometric design concept used to allow a large actual focal spot area for maximum heat dissipation while maintaining a small effective focal spot for superior image spatial resolution.

Actual Focal Spot : The area on the anode target face impacted by the electron beam.

Effective Focal Spot : The area of the X-ray beam projected downward perpendicularly toward the patient and image receptor.

By angling the target face relative to the vertical axis (typically 7 ∘ 7^\circ 7 ∘ to 17 ∘ 17^\circ 1 7 ∘ , with an average target angle of 12 ∘ 12^\circ 1 2 ∘ ), the effective focal spot size becomes significantly smaller than the actual focal spot size according to the geometric relationship: Effective Focal Spot Size = Actual Focal Spot Size × sin ⁡ ( θ ) \text{Effective Focal Spot Size} = \text{Actual Focal Spot Size} \times \sin(\theta) Effective Focal Spot Size = Actual Focal Spot Size × sin ( θ )

As the target angle ( θ \theta θ ) decreases (becomes steeper), the effective focal spot becomes smaller, producing sharper radiographic images with reduced geometric unsharpness (penumbra).

The Anode Heel Effect

Because X-rays are produced at a finite depth within the target anode face, photons emitted toward the anode side of the target must pass through a greater thickness of target material than those emitted toward the cathode side. This differential attenuation produces the anode heel effect :

Radiation intensity is significantly higher on the cathode side (up to 120% of central ray intensity).

Radiation intensity is significantly lower on the anode side (down to 75% of central ray intensity).

Across the entire field, radiation intensity can vary by up to 45% .

Clinical Application:

To achieve uniform radiographic image density when examining body parts of asymmetrical thickness, the thicker anatomical structure must be positioned under the cathode side , and the thinner structure under the anode side (e.g., placing the proximal thicker femur under the cathode end and the distal thinner knee under the anode end).

Factors Exacerbating the Heel Effect:

Smaller Anode Target Angles (steeper angles increase target path length for anode-bound photons).

Shorter Source-to-Image Distances (SID) (includes more of the divergent periphery of the beam).

Larger Field Sizes / Image Receptor Sizes (captures the outer edges of intensity variation).

Protective Housing & Tube Cooling

The X-ray tube glass or metal envelope is housed inside a heavy lead-lined cast steel casing called the protective housing .

Key Functions of the Housing:

Radiation Protection : X-rays are emitted isotropically (in all directions) from the target. The lead lining absorbs off-target and non-diagnostic X-rays. Federal standards require that leakage radiation must not exceed 1 mGy/hr 1\text{ mGy/hr} 1 mGy/hr ( 100 mR/hr 100\text{ mR/hr} 100 mR/hr ) at a distance of 1 meter when operated at maximum continuous conditions.

Electrical Insulation & Thermal Dissipation : The housing is filled with dielectric oil that surrounds the tube envelope, providing high-voltage electrical insulation and conducting heat away from the tube toward the housing walls. External cooling fans accelerate thermal dissipation.

Factors Influencing the X-Ray Emission Spectrum

The X-ray emission spectrum graphically illustrates the distribution of photon energies within the X-ray beam, plotting X-ray quantity (number of photons) on the y-axis against X-ray quality (energy in keV) on the x-axis.

Milliamperage-Seconds (mAs) : Directly proportional to X-ray quantity. Doubling mAs doubles the amplitude (height) of both Bremsstrahlung and Characteristic spectrum curves at all energy levels. Beam quality (peak and average photon energy) remains completely unchanged.

Peak Kilovoltage (kVp) : Influences both quantity and quality. Increasing kVp increases total photon quantity proportionally to kVp 2 \text{kVp}^2 kVp 2 . Graphically, the curve shifts upward and to the right , increasing the maximum photon energy ( E max ⁡ = kVp E_{\max} = \text{kVp} E m a x ​ = kVp ) and elevating the average energy of the beam.

Added Filtration : Passing the beam through aluminum absorbers removes low-energy, non-diagnostic photons ("beam hardening"). Added filtration decreases overall beam quantity (amplitude drops) while increasing average beam energy (curve shifts right) . Regulations mandate a minimum of 2.5 mm Aluminum equivalent total filtration for diagnostic tubes operating above 70 kVp.

Target Material Atomic Number ( Z Z Z ) : Increasing target atomic number increases Bremsstrahlung production efficiency (higher amplitude) and shifts discrete characteristic energy spikes to higher discrete energies.

Generator Waveform : Voltage ripple describes the percentage variation between peak and minimum voltage across an exposure cycle. Lower voltage ripple delivers higher average electron kinetic energy, producing greater beam quantity and higher average photon energy (beam quality).

Heat Units (HU) Calculation & Rating Systems

Thermal load generated during exposure must be monitored to prevent target destruction. Heat Units (HU) quantify thermal energy deposited on the anode target.

Heat Unit Formula: HU = kVp × mA × time (seconds) × Generator Factor \text{HU} = \text{kVp} \times \text{mA} \times \text{time (seconds)} \times \text{Generator Factor} HU = kVp × mA × time (seconds) × Generator Factor

  • Generator Type Voltage Ripple (%) Generator Factor
  • Single-Phase (1-Phase) 100% 1.00
  • Three-Phase, 6-Pulse 14% 1.35
  • Three-Phase, 12-Pulse 4% 1.40
  • High-Frequency (HF) < 1 % < 1\% < 1% 1.40 (or 1.45)

Sample Thermal Calculation:

Calculate the total Heat Units generated by a series of 3 exposures using 85 kVp, 400 mA, 0.15 seconds on a three-phase, 12-pulse X-ray generator: Single Exposure HU = 85 × 400 × 0.15 × 1.40 = 7 , 140 HU \text{Single Exposure HU} = 85 \times 400 \times 0.15 \times 1.40 = 7,140\text{ HU} Single Exposure HU = 85 × 400 × 0.15 × 1.40 = 7 , 140 HU Total Thermal Load (3 exposures) = 7 , 140 × 3 = 21 , 420 HU \text{Total Thermal Load (3 exposures)} = 7,140 \times 3 = \mathbf{21,420\text{ HU}} Total Thermal Load (3 exposures) = 7 , 140 × 3 = 21 , 420 HU