Study guide
5.1 Specimen Labeling & Transport
CPT Certified Phlebotomy Technician Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction: CPT Phlebotomy Exam Overview
NHA CPT Exam Overview CPT Certification Process Anatomy & Physiology for Phlebotomists
2 Chapter 1: Safety & Compliance (26%)
1.1 Infection Control & Personal Protective Equipment (PPE) 1.2 OSHA Regulations & Workplace Safety
3 Chapter 2: Patient Preparation & Identification (20%)
2.1 Patient Identification & Communication 2.2 Patient Preparation & Positioning
4 Chapter 3: Venipuncture Procedures (Routine Blood Collections, 28%)
3.1 Venipuncture Equipment & Technique 3.2 Order of Draw 3.3 Difficult Draws & Complications
5 Chapter 4: Capillary Puncture (Routine Blood Collections) & Special Collections (12%)
4.1 Capillary (Dermal) Puncture Technique 4.2 Special Collection Procedures
6 Chapter 5: Specimen Handling & Processing (14%)
5.1 Specimen Labeling & Transport 5.2 Specimen Processing & Quality Assurance
5.1 Specimen Labeling & Transport
Key Takeaways Explain This Topic AI
Specimens must be labeled AT THE BEDSIDE immediately after collection — NEVER pre-label tubes before drawing blood
Minimum labeling requirements include: patient full name, date of birth or MRN, date and time of collection, and phlebotomist initials or ID
Mislabeled or unlabeled specimens must be REJECTED — the draw must be repeated; relabeling at a later time is NOT acceptable
Specimens should be transported to the laboratory within 45 minutes to 2 hours of collection, depending on the test
Transport temperature categories include: room temperature (most specimens), chilled/on ice (ABG, ammonia, lactic acid), body temperature (cold agglutinins, cryoglobulins), and protected from light (bilirubin)
Specimens must be transported in a sealed, leak-proof biohazard bag with the requisition form in a separate compartment
Pneumatic tube systems can be used for most routine specimens but are NOT recommended for ABGs, cryoglobulins, or specimens prone to hemolysis
Delay in transport can cause glucose levels to decrease (glycolysis), potassium levels to increase (cell leakage), and coagulation factors to degrade
Last updated: February 2026
Specimen labeling and transport are the final critical steps in the phlebotomy process. Errors at this stage can invalidate otherwise perfectly collected specimens and lead to patient harm. The preanalytical phase (everything before the laboratory performs the test) accounts for the majority of all laboratory errors.
- Specimen Labeling Requirements
- Minimum Required Information
Every specimen label must include:
- Required Field Details
- Patient full name First and last name (must match requisition and wristband)
- Date of birth or Medical Record Number (MRN) Second unique identifier
- Date of collection Month, day, year
- Time of collection Include AM/PM or use 24-hour format
- Phlebotomist identification Initials, employee ID, or full name
- Specimen source (if applicable) e.g., "left antecubital" or "right hand"
- Labeling Rules
- Rule Explanation
- Label at the bedside Labels must be applied in the patient's presence, after the draw is complete
- NEVER pre-label tubes Pre-labeling creates a risk of attaching the wrong label to the wrong specimen
- Verify with the patient Confirm the label matches the patient's stated identifiers
- One patient at a time Never collect specimens from multiple patients before labeling
- Handwritten labels Must be legible; printed labels are preferred
What Happens with Labeling Errors?
- Error Type Required Action
- Unlabeled specimen REJECT — must redraw; cannot label after the fact
- Mislabeled specimen REJECT — must redraw; the risk of patient misidentification is too high
- Illegible label REJECT — must redraw
Missing required information May be correctable if the phlebotomist can verify at the bedside; otherwise REJECT
Label on the tube (correct) Acceptable — labels go on the tube, not on the bag
Key Fact: Specimen labeling errors account for a significant portion of preanalytical errors and are a leading cause of wrong blood in tube (WBIT) events, which can result in fatal transfusion reactions or incorrect treatment decisions.
- Specimen Transport
- General Transport Guidelines
- Time: Deliver specimens to the laboratory within 45 minutes to 2 hours of collection
- Container: Use a sealed, leak-proof biohazard transport bag
- Requisition form: Place in a separate compartment of the bag (not touching the specimen)
- Upright position: Transport tubes upright (stoppers up) when possible to promote clot formation in serum tubes
- Transport Temperature Requirements
Temperature Specimens Method
Room temperature (20-25C) Most routine specimens (CBC, BMP, CMP, coagulation, blood bank) Standard biohazard bag
Chilled / On ice (2-8C) ABG, ammonia, lactic acid, ACTH, gastrin, parathyroid hormone (PTH), catecholamines Place tube in cup of ice water (NOT directly on ice — direct ice contact can cause hemolysis)
Body temperature (37C) Cold agglutinins, cryoglobulins, cryofibrinogen Pre-warmed container or heat block
Protected from light Bilirubin, vitamin B12, folate, porphyrins, vitamin A, carotene Wrap in aluminum foil or use amber tubes
Effects of Transport Delays
- Analyte Effect of Delay Cause
- Glucose Decreases Glycolysis (cells continue to consume glucose)
- Potassium (K+) Increases Leakage from red blood cells
- Lactate Increases Continued cellular metabolism
- Ammonia Increases Protein deamination continues
- Coagulation factors Degrade Factor V and Factor VIII are labile (unstable)
- pH (for ABG) Decreases CO2 production continues; metabolism produces acid
- Pneumatic Tube Systems
Most hospitals use pneumatic tube systems to transport specimens quickly:
- Acceptable NOT Recommended
- Routine chemistry ABG specimens
- CBC and hematology Cryoglobulins / cold agglutinins
- Coagulation Specimens prone to hemolysis
- Urinalysis Blood bank crossmatch (some facilities)
- Blood cultures Fragile cell studies
- Special Handling Situations
- STAT Specimens
- STAT means "immediately" — these specimens have the highest priority
- Transport to the lab immediately by hand (do NOT use the pneumatic tube system if hand delivery is faster)
- Results are typically reported within 1 hour
- Common STAT tests: troponin (heart attack), potassium (critical electrolyte), glucose, hemoglobin
- Timed Specimens
- Specimens that must be drawn at a specific time (peak/trough drug levels, cortisol, GTT draws)
- Document the EXACT time of collection on the label and requisition
- Timing errors can render the results clinically meaningless
- Specimens Collected During Blood Transfusion
- Blood bank specimens for type and screen must be collected before the transfusion begins
- Post-transfusion specimens should be labeled with the time relative to the transfusion
- Follow facility-specific blood bank identification protocols (some require special armbands)