Study guide

10.2 Donning & Doffing Sequence

PTCB Hazardous Drug Management Certificate Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

0.1 Exam Facts, Format & Eligibility 0.2 Content Outline, Scoring & Registration 0.3 USP <800> Big Picture & How to Use This Guide

2 USP <800> Program Administration

1.1 USP <800> Scope, Purpose & Enforcement 1.2 The NIOSH Hazardous Drug List (2024 Update) 1.3 Assessment of Risk 1.4 Designated Person, SOPs & the Hierarchy of Controls

3 Training, Compliance & Recordkeeping

2.1 Training Requirements & Medical Surveillance 2.2 Hazard Communication, SDS & OSHA Requirements 2.3 Recordkeeping & Professional Guidelines

4 Primary Engineering Controls

3.1 Containment Primary Engineering Controls (C-PEC): BSCs & CACIs 3.2 Closed System Transfer Devices (CSTDs) 3.3 Nonsterile Controls and the C-SCA Distinction

5 Secondary Engineering Controls & Facility Design

4.1 Containment Secondary Engineering Controls (C-SEC): Negative Pressure & Air Exchange 4.2 Facility Layout: Storage, Unpacking & Sink Placement 4.3 Certification, ISO Classes & Emergency Equipment

6 Facility Cleaning Procedures

5.1 The Four-Step Cleaning Process 5.2 Wipe Sampling & Action Levels 5.3 Hazardous Waste Disposal & RCRA

7 Spill Response & Cleaning PPE

6.1 Spill Kits & Spill Response Procedures 6.2 PPE During Cleaning: Glove Change Frequency & Disposal

8 Dispensing & the Compounding Interface

7.1 USP <795>/<797> Interface for Hazardous Drugs 7.2 High-Risk Oral Hazardous Drugs 7.3 Tablet Splitting & Crushing Restrictions

9 Counting, Packaging & Patient Counseling

8.1 Counting, Packaging & Dedicated Equipment 8.2 Patient Counseling & Unit-Dose Labeling

10 PPE: Gloves, Gowns & Task-Based Selection

9.1 ASTM D6978 Chemotherapy Gloves & Double Gloving 9.2 Chemo Gowns & Gown Change Frequency 9.3 Task-Based PPE Selection

11 Respiratory Protection, Eye Protection & PPE Sequencing

10.1 Respiratory & Eye/Face Protection 10.2 Donning & Doffing Sequence

12 Transport & Receiving

11.1 Receiving Hazardous Drug Shipments 11.2 Internal Transport & Storage 11.3 Damaged/Leaking Shipments & Chain of Custody

13 Exam Readiness & Final Review

12.1 Domain-by-Domain Quick Review 12.2 Common Exam Traps & Final Checklist

10.2 Donning & Doffing Sequence

Key Takeaways Explain This Topic AI

Donning order: shoe covers, first (inner) gloves, gown, second (outer) gloves pulled over the gown cuffs, then head/hair cover, mask/respirator, and eye protection as needed for the task

Outer gloves go OVER the gown cuff, not under it, to eliminate any gap of exposed skin at the wrist - this is the most commonly missed detail on the exam

Doffing order: outer gloves first (most contaminated), gown rolled inward away from the body, inner gloves removed last, then head cover/mask/eye protection, then immediate hand hygiene

Inner gloves are removed last because hands may carry residual contamination on the outer glove surface throughout the task, so keeping that barrier on protects the hands the longest

The universal doffing rule tested across scenario questions: the contaminated outer surface of any PPE item must never touch bare skin during removal

Last updated: July 2026

Donning and Doffing Sequence for Hazardous Drug PPE

The order in which personal protective equipment (PPE) is put on (donned) and taken off (doffed) is not arbitrary - it exists to prevent a two-way contamination pathway: keeping HD residue off the technician's skin while donning, and preventing PPE that became contaminated during a task from touching skin or clothing while doffing. This is one of the most heavily tested sequencing topics in the PPE domain (13% of the exam), because it rewards precise step-by-step recall rather than general familiarity with PPE items.

Guiding Principle

Donning proceeds from least contaminated to most contaminated - items that will end up closest to the technician's skin and hardest to fix later (like the gown cuff/wrist seal) go on before the items that lock them in place. Doffing reverses that logic but adds a second rule: remove the most contaminated item first , and never let the outside (contaminated) surface of any PPE item touch bare skin during removal.

Donning Sequence (Putting On)

  • Step Item Why This Order
  • 1 Shoe covers Lowest contamination risk; done first, before handling any other PPE
  • 2 First (inner) pair of gloves Establishes a base hand barrier before the gown goes on
  • 3 Gown Body barrier; put on before the outer gloves so its cuffs can be tucked underneath them

4 Second (outer) pair of gloves Pulled over the gown cuffs, sealing the wrist - the critical control point that eliminates any gap of exposed skin

5 Head/hair cover, mask or respirator, and eye protection (as needed for the task) Donned last, closest to the face/airway, and selected based on the specific task's respiratory and splash risk

The step that most often trips up candidates is step 4: the outer glove goes over the gown cuff, not under it. Tucking the gown cuff underneath the outer glove means there is no exposed skin at the wrist even if the technician's arm moves during compounding or spill response.

Doffing Sequence (Taking Off)

Doffing is the reverse order, but the reasoning is about contamination containment rather than a simple inversion of steps:

Step Item Why This Order

1 Outer gloves (most contaminated item) Removed first because they had the most direct contact with HD residue; peeled off without letting the outer surface touch skin

2 Gown Rolled inward, away from the body, so the contaminated exterior surface folds in on itself and never contacts skin or clothing

3 Inner gloves (removed last) Hands may retain residual contamination on the outer surface of the inner gloves throughout the procedure, so keeping this barrier on as long as possible protects the hands until the very end

4 Head/hair cover, mask/respirator, eye protection Removed after the higher-contamination-risk items

5 Hand hygiene Performed immediately after all PPE is removed, regardless of how carefully the technician doffed

The Core Doffing Rule

When a scenario question asks about doffing technique rather than a specific step order, the underlying principle being tested is almost always the same: the outside (potentially contaminated) surface of any PPE item must never touch bare skin during removal. This is why the gown is rolled inward rather than pulled off overhead, and why gloves are peeled from the wrist rather than grabbed by the outer surface.

Worked Scenario

A technician finishes compounding a hazardous injectable drug inside a BSC and steps back to a designated doffing area outside the C-PEC to remove PPE. The correct first move is to remove the outer gloves - not the gown, and not the inner gloves - because the outer gloves have had the most direct contact with the HD and any surfaces touched during compounding. After the outer gloves are removed and discarded, the technician rolls the gown inward and away from the body, then removes the inner gloves last, followed by the head cover, mask, and eye protection, and finally performs hand hygiene. If the technician instead removed the gown first while the outer gloves were still on, exposed skin at the wrist (from arm movement during the reach) could brush the contaminated gown surface - exactly the failure mode the sequence is designed to prevent.

Key Takeaways

Donning order: shoe covers, first (inner) gloves, gown, second (outer) gloves over the gown cuffs, then head cover/mask/respirator/eye protection

Outer gloves go OVER the gown cuff, not under it, to eliminate any gap of exposed skin at the wrist

Doffing order: outer gloves first (most contaminated), gown rolled inward, inner gloves last, then head cover/mask/eye protection, then hand hygiene

Inner gloves are removed last because they protect the hands the longest against residual contamination accumulated during the task

The universal doffing rule: the contaminated outer surface of any PPE item must never touch bare skin during removal