Study guide
8.3 Heat Exchangers and LMTD
UPDA/MMUP Engineer Registration Exam — Chemical Qatar
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts and Format 1.2 Registration, Eligibility, Grades, and Renewal 1.3 Study Strategy and Exam-Day Tactics
2 Stoichiometry & Process Calculation Foundations
2.1 Units, Bases, and Process Variables 2.2 Stoichiometry, Limiting and Excess Reactants 2.3 Batch vs Continuous and Steady vs Unsteady Operation
3 Material Balances
3.1 Steady Material Balances Without Reaction 3.2 Material Balances With Chemical Reaction 3.3 Recycle, Bypass, and Purge Systems
4 Energy Balances
4.1 Energy Forms and the First Law for Processes 4.2 Heats of Reaction and Formation 4.3 Process Energy Balance Applications
5 Thermodynamics Fundamentals
5.1 Thermodynamic Laws and State Functions 5.2 Equations of State and Real Gases 5.3 Enthalpy, Entropy, and Heat Capacity
6 Phase and Chemical Equilibria
6.1 Phase Equilibria and VLE Fundamentals 6.2 Bubble Point, Dew Point, and Flash Concepts 6.3 Chemical Reaction Equilibrium
7 Fluid Mechanics
7.1 Fluid Properties, Reynolds Number, and Flow Regimes 7.2 Bernoulli Equation and Mechanical Energy Balance 7.3 Pipe Flow, Friction, and Pumps
8 Heat Transfer
8.1 Conduction, Convection, and Radiation 8.2 Heat Transfer Coefficients and Overall U 8.3 Heat Exchangers and LMTD
9 Mass Transfer and Separations
9.1 Mass Transfer and Diffusion Fundamentals 9.2 Distillation Columns and Operations 9.3 Absorption, Stripping, and Extraction
10 Chemical Reaction Engineering
10.1 Rate Laws and Reaction Order 10.2 Arrhenius Equation and Temperature Effects 10.3 Batch and CSTR Reactors 10.4 PFR Design and Reactor Selection
11 Process Instrumentation and Control
11.1 Process Instrumentation and Measurement 11.2 Feedback Control and PID 11.3 Process Dynamics, Alarms, and Interlocks
12 Process Safety, Qatar Codes and Professional Conduct
12.1 Process Safety Fundamentals and Inherent Safety 12.2 HAZOP Methodology 12.3 LOPA, Relief Systems, and Emergency Response 12.4 Fire Protection, Environment, and Qatar Plant Context 12.5 Qatar Codes, Standards, and Professional Conduct
13 Engineering Economics and Cost Analysis
13.1 Cost Structures and Break-Even Analysis 13.2 Depreciation and the Time Value of Money 13.3 Project Economics, Estimating, and Cost Control
14 Project Management Principles (PMP)
14.1 PM Framework, Process Groups, and Knowledge Areas 14.2 Scope, Schedule, and Cost Management 14.3 Risk, Quality, and Stakeholder Management
8.3 Heat Exchangers and LMTD
Key Takeaways Explain This Topic AI
Exchanger duty from the process side: Q̇ = ṁ C_p ΔT for sensible heating/cooling (no phase change); match to the other stream’s energy balance.
LMTD = (ΔT₁ − ΔT₂) / ln(ΔT₁/ΔT₂), where ΔT₁ and ΔT₂ are the temperature differences between hot and cold fluids at the two ends.
Counter-current flow usually sustains a more favorable ΔT profile than co-current; co-current cold outlet cannot exceed hot outlet in the simple ideal limit.
Shell-and-tube and double-pipe are common types; multipass shell-and-tube often needs an LMTD correction factor F so Q̇ = U A F (LMTD_cf).
Work LMTD problems by labeling both ends, computing end differences, then applying the log-mean—never the arithmetic mean of the two end ΔT values when they differ.
Last updated: August 2026
8.3 Heat Exchangers and LMTD
Quick Answer: Duty Q̇ = ṁ C_p ΔT (sensible). Mean driving force for many exchangers is the log mean temperature difference (LMTD) . Counter-current usually beats co-current . Multipass units use Q̇ = U A F (LMTD) with correction F ≤ 1 .
Sections 8.1–8.2 built mechanisms and overall U . This section closes Domain C heat transfer for typical UPDA items: energy balance on both streams , LMTD , flow arrangement, and basic shell-and-tube / double-pipe awareness used across Qatar process plants.
Energy Balance on a Heat Exchanger
At steady state, neglecting heat loss to ambient and shaft work:
- Heat lost by hot stream = heat gained by cold stream = Q̇
- Sensible Heat Only (No Phase Change)
- Q̇ = ṁ_h C_p,h (T_h,in − T_h,out) = ṁ_c C_p,c (T_c,out − T_c,in)
- Symbol Meaning
- ṁ_h, ṁ_c Hot and cold mass flow rates
- C_p,h, C_p,c Average heat capacities
- T_h,in, T_h,out Hot inlet / outlet temperatures
- T_c,in, T_c,out Cold inlet / outlet temperatures
Exam checks:
Close the energy balance—do not invent a duty inconsistent with both streams.
Use consistent units (°C differences are fine for ΔT; C_p in kJ/(kg·K) with ṁ in kg/s → Q̇ in kW).
If a stream condenses or boils at constant pressure, use ṁ × λ (latent heat) instead of ṁ C_p ΔT for that portion.
Worked Duty Example
Cold oil is heated from 35 °C to 75 °C at ṁ_c = 2.4 kg/s with C_p,c = 2.1 kJ/(kg·K).
Q̇ = 2.4 × 2.1 × (75 − 35) = 2.4 × 2.1 × 40 = 201.6 kW
Hot fluid: ṁ_h = 1.8 kg/s, C_p,h = 2.8 kJ/(kg·K), T_h,in = 120 °C. Find T_h,out (no losses).
- 201.6 = 1.8 × 2.8 × (120 − T_h,out)
- 201.6 = 5.04 × (120 − T_h,out)
- 120 − T_h,out = 40.0
- T_h,out = 80.0 °C
- Stream ṁ (kg/s) C_p (kJ/(kg·K)) T_in (°C) T_out (°C) Q̇ (kW)
- Cold 2.4 2.1 35 75 +201.6
- Hot 1.8 2.8 120 80 −201.6
- LMTD Definition and Formula
For a exchanger with constant U and approximately constant C_p streams, integration along the unit yields:
Q̇ = U A ΔT_lm
Log mean temperature difference:
ΔT_lm = LMTD = (ΔT_a − ΔT_b) / ln(ΔT_a / ΔT_b)
where ΔT_a and ΔT_b are the local hot-minus-cold temperature differences at the two ends of the exchanger.
- If ΔT_a ≈ ΔT_b Then LMTD ≈ that common ΔT (log mean → arithmetic mean)
- If ΔT_a and ΔT_b differ a lot Arithmetic mean overpredicts driving force; use log mean
Never use (ΔT_a + ΔT_b)/2 as a substitute when the exam is testing LMTD—unless the two end differences are essentially equal.
Counter-Current vs Co-Current End Differences
Counter-current (counterflow): hot and cold flow in opposite directions.
- End A: hot inlet meets cold outlet → ΔT_A = T_h,in − T_c,out
- End B: hot outlet meets cold inlet → ΔT_B = T_h,out − T_c,in
Co-current (parallel flow): both enter at the same end.
- Inlet end: ΔT_in = T_h,in − T_c,in
- Outlet end: ΔT_out = T_h,out − T_c,out
Arrangement Advantage Limitation
Counter-current Larger LMTD for same terminals; cold can exit hotter than hot outlet Headering slightly more complex in some layouts
Co-current Can limit metal temperature at the hot end in some services Cold outlet cannot exceed hot outlet; usually smaller LMTD
Classic feasibility: In pure co-current flow, T_c,out cannot exceed T_h,out. Counter-current can allow T_c,out > T_h,out while still keeping local ΔT positive everywhere if designed properly.
Using the numerical temperatures above (T_h 120→80 °C, T_c 35→75 °C):
Counter-current ends:
- ΔT_A = 120 − 75 = 45 °C
- ΔT_B = 80 − 35 = 45 °C
- LMTD_cf = 45 °C (equal ends)
Co-current ends:
- ΔT_in = 120 − 35 = 85 °C
- ΔT_out = 80 − 75 = 5 °C
- LMTD_co = (85 − 5) / ln(85/5) = 80 / ln(17) = 80 / 2.833 ≈ 28.2 °C
Same terminal temperatures, much smaller co-current LMTD → needs more area (or higher U) for the same duty.
- Flow ΔT_end1 (°C) ΔT_end2 (°C) LMTD (°C)
- Counter-current 45 45 45.0
- Co-current 85 5 ~28.2
- Worked LMTD Numerical Example (Original Numbers)
Problem. A double-pipe exchanger cools a hot process liquid from 155 °C to 95 °C . Cooling water heats from 28 °C to 46 °C . Assume pure counter-current flow, steady state, no heat loss. U = 420 W/(m²·K) . Hot stream: ṁ_h = 1.25 kg/s , C_p,h = 2.40 kJ/(kg·K) .
Find: (1) duty Q̇, (2) required cold-water mass flow if C_p,c = 4.18 kJ/(kg·K) , (3) LMTD, (4) required area A.
- Step 1 — Duty from hot stream
- Q̇ = 1.25 × 2.40 × (155 − 95) = 1.25 × 2.40 × 60 = 180 kW = 180,000 W
- Step 2 — Cold-water flow
- 180 = ṁ_c × 4.18 × (46 − 28)
- 180 = ṁ_c × 4.18 × 18
- 180 = ṁ_c × 75.24
- ṁ_c = 2.39 kg/s (approximately)
- Step 3 — Counter-current end differences
- ΔT₁ = T_h,in − T_c,out = 155 − 46 = 109 °C ΔT₂ = T_h,out − T_c,in = 95 − 28 = 67 °C
- LMTD = (109 − 67) / ln(109/67) = 42 / ln(1.627) = 42 / 0.4867 ≈ 86.3 °C
- Step 4 — Area
- Q̇ = U A (LMTD)
- 180,000 = 420 × A × 86.3
- A = 180,000 / (420 × 86.3) ≈ 180,000 / 36,246 ≈ 4.97 m²
- Quantity Value
- Q̇ 180 kW
- ṁ_c ~2.39 kg/s
- ΔT₁ 109 °C
- ΔT₂ 67 °C
- LMTD ~86.3 °C
- U 420 W/(m²·K)
- A ~5.0 m²
Arithmetic-mean trap: (109 + 67)/2 = 88 °C, close here because the ratio is moderate—but still not the definition. When one end ΔT is small (pinch), arithmetic mean badly overestimates driving force and undersizes the exchanger.
Shell-and-Tube and Double-Pipe Awareness
- Type Configuration Typical use
- Double-pipe One pipe inside another; often pure counterflow Small duties, high pressure, teaching ideal LMTD
Shell-and-tube Bundle of tubes in a shell; baffles drive shell-side crossflow Workhorse for process plants (Qatar gas/oil/chem)
- Air-cooled (fin-fan) Process in tubes, air forced over fins Cooling water scarcity or air cooler banks
- Plate Gasketed or welded plates Compact liquid–liquid services
- When the F Correction Appears
True pure counterflow LMTD is exact only for certain arrangements (e.g., ideal double-pipe counterflow, or 1-1 pure counterflow).
Multipass shell-and-tube exchangers (e.g., 1 shell pass / 2 tube passes) mix crossflow and multipass patterns. Industry practice:
Q̇ = U A F (LMTD_counterflow)
LMTD_counterflow is computed as if the exchanger were pure counterflow with the same four terminal temperatures
F is a correction factor from charts (function of two dimensionless temperature ratios), 0 < F ≤ 1
If F is low (often warned below ~0.75–0.8), temperature crosses or multipass limits—consider more shell passes or different arrangement
UPDA level: Know why F exists (flow is not pure counterflow) and that F multiplies LMTD , reducing effective driving force. You are not expected to redraw TEMA F-charts from memory.
Qualitative Design Notes
Put fouling or corrosive fluid on the tube side when that eases cleaning/metallurgy (common heuristic—not absolute)
- Cooling water often on tube side in many plant standards
- Baffles raise shell-side h (velocity) but increase ΔP
Approach temperature: difference between hot outlet and cold inlet (or other specified pair)—small approaches need large A
Linking U, A, LMTD, and Fouling
From Section 8.2, fouling lowers U. For fixed A and terminal temperatures (fixed LMTD), duty falls. Operators may open utility valves (change flows → new terminals and new LMTD) until limits. Designers pick A using dirty U and appropriate F × LMTD so the unit still delivers required Q̇ at end of run.
- Common Traps
- Using co-current end pairs while claiming counterflow LMTD
- Arithmetic mean instead of log mean when ΔT₁ ≠ ΔT₂
- Forgetting F conceptually on multipass shells (overestimating driving force)
- Mismatched energy balance (hot Q̇ ≠ cold Q̇) before computing LMTD
- Celsius vs kelvin confusion—ΔT in °C equals ΔT in K; absolute T only needed for radiation
- Exam Workflow
Draw streams; label all four temperatures.
Compute Q̇ from the fully known stream; find the missing flow or temperature on the other side.
Choose counter vs co-current end ΔT pairs as the stem requires.
Compute LMTD = (ΔT₁ − ΔT₂)/ln(ΔT₁/ΔT₂).
Apply Q̇ = U A (F)(LMTD) ; solve for the unknown (often A or U).
Comment on fouling or F if the stem mentions dirty service or multipass shells.
With mechanisms (8.1), overall U and fouling (8.2), and LMTD exchangers (8.3), you have the heat half of Domain C transport. Mass transfer and separations follow in Chapter 9.