Study guide

9.3 Absorption, Stripping, and Extraction

UPDA/MMUP Engineer Registration Exam — Chemical Qatar

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts and Format 1.2 Registration, Eligibility, Grades, and Renewal 1.3 Study Strategy and Exam-Day Tactics

2 Stoichiometry & Process Calculation Foundations

2.1 Units, Bases, and Process Variables 2.2 Stoichiometry, Limiting and Excess Reactants 2.3 Batch vs Continuous and Steady vs Unsteady Operation

3 Material Balances

3.1 Steady Material Balances Without Reaction 3.2 Material Balances With Chemical Reaction 3.3 Recycle, Bypass, and Purge Systems

4 Energy Balances

4.1 Energy Forms and the First Law for Processes 4.2 Heats of Reaction and Formation 4.3 Process Energy Balance Applications

5 Thermodynamics Fundamentals

5.1 Thermodynamic Laws and State Functions 5.2 Equations of State and Real Gases 5.3 Enthalpy, Entropy, and Heat Capacity

6 Phase and Chemical Equilibria

6.1 Phase Equilibria and VLE Fundamentals 6.2 Bubble Point, Dew Point, and Flash Concepts 6.3 Chemical Reaction Equilibrium

7 Fluid Mechanics

7.1 Fluid Properties, Reynolds Number, and Flow Regimes 7.2 Bernoulli Equation and Mechanical Energy Balance 7.3 Pipe Flow, Friction, and Pumps

8 Heat Transfer

8.1 Conduction, Convection, and Radiation 8.2 Heat Transfer Coefficients and Overall U 8.3 Heat Exchangers and LMTD

9 Mass Transfer and Separations

9.1 Mass Transfer and Diffusion Fundamentals 9.2 Distillation Columns and Operations 9.3 Absorption, Stripping, and Extraction

10 Chemical Reaction Engineering

10.1 Rate Laws and Reaction Order 10.2 Arrhenius Equation and Temperature Effects 10.3 Batch and CSTR Reactors 10.4 PFR Design and Reactor Selection

11 Process Instrumentation and Control

11.1 Process Instrumentation and Measurement 11.2 Feedback Control and PID 11.3 Process Dynamics, Alarms, and Interlocks

12 Process Safety, Qatar Codes and Professional Conduct

12.1 Process Safety Fundamentals and Inherent Safety 12.2 HAZOP Methodology 12.3 LOPA, Relief Systems, and Emergency Response 12.4 Fire Protection, Environment, and Qatar Plant Context 12.5 Qatar Codes, Standards, and Professional Conduct

13 Engineering Economics and Cost Analysis

13.1 Cost Structures and Break-Even Analysis 13.2 Depreciation and the Time Value of Money 13.3 Project Economics, Estimating, and Cost Control

14 Project Management Principles (PMP)

14.1 PM Framework, Process Groups, and Knowledge Areas 14.2 Scope, Schedule, and Cost Management 14.3 Risk, Quality, and Stakeholder Management

9.3 Absorption, Stripping, and Extraction

Key Takeaways Explain This Topic AI

Gas absorption (scrubbing) transfers a solute from a gas into a liquid solvent; lean solvent enters the top and rich solvent leaves the bottom in a countercurrent tower.

Stripping (desorption) is the reverse: solute is removed from a liquid into a gas (steam, air, or inert) so solvent can be regenerated.

Liquid–liquid extraction transfers a solute from a feed liquid (raffinate path) into an immiscible solvent (extract path) based on partition/selectivity.

Prefer absorption for dilute gas solutes with a good solvent; stripping to regenerate solvent or clean liquids; extraction when distillation is hard (close boilers, heat-sensitive, or favorable liquid partition).

All three operations combine equilibrium (solubility/partition) with mass-transfer rates and countercurrent staging.

Last updated: August 2026

9.3 Absorption, Stripping, and Extraction

Quick Answer: Absorption moves solute gas → liquid ( lean in, rich out). Stripping is the reverse (liquid → gas) for regeneration or cleanup. Extraction moves solute between immiscible liquids ( raffinate depleted, extract enriched). Choose by solubility, selectivity, heat sensitivity, and dilute vs concentrated feeds.

Not every separation is a distillation column. Acid-gas removal from natural gas, amine systems, sour-water strippers, wastewater VOC treatment, and aromatic/specialty separations all use absorption , stripping , or liquid–liquid extraction . These unit operations sit squarely in Domain C with the mass-transfer fundamentals of Section 9.1 and the equilibrium ideas of Domain B.

Gas Absorption and Scrubbing

Gas absorption (gas scrubbing when the goal is purification/emission control) contacts a gas mixture with a liquid solvent that preferentially dissolves one or more solutes (e.g., H₂S, CO₂, NH₃, SO₂, light organics).

Goals

  • Goal Example
  • Product purification Remove H₂S/CO₂ from sales gas or syngas
  • Emission control Scrub SO₂ or acid gases from flue/process vents
  • Recovery Recover valuable vapor into a solvent for reuse
  • Safety Knock down toxic or flammable vapors
  • Countercurrent tower picture

Typical packed or tray absorber :

Gas enters bottom (rich in solute), leaves top (lean gas / treated gas).

Liquid solvent enters top lean , leaves bottom rich .

Countercurrent flow maximizes average driving force: richest gas meets richest liquid; leanest gas meets leanest liquid.

  • Stream name Meaning
  • Lean solvent Low solute loading; high capacity to absorb
  • Rich solvent High solute loading; sent to regeneration (stripper) or disposal
  • L/G ratio Liquid rate / gas rate; must exceed minimum for the separation (analogous to minimum reflux logic)

Equilibrium: Henry’s law or solubility curves give y ∗ y^* y ∗ (or p*) in equilibrium with liquid x. Operating line from material balance must stay on the correct side of equilibrium (driving force y − y ∗ > 0 y - y^* > 0 y − y ∗ > 0 for absorption of solute into liquid).

Minimum liquid rate: as L decreases, the operating line pivots toward the equilibrium curve and pinches—infinite height required. Practical absorbers use L above L min ⁡ L_{\min} L m i n ​ .

Worked L/G sketch (dilute)

Gas in: G = 100 mol/s, y i n = 0.02 y_{\mathrm{in}} = 0.02 y in ​ = 0.02 mole fraction solute (dilute). Target y o u t = 0.002 y_{\mathrm{out}} = 0.002 y out ​ = 0.002 . Inlet lean liquid x i n = 0 x_{\mathrm{in}} = 0 x in ​ = 0 . Suppose equilibrium is y ∗ = 1.5 x y^* = 1.5 x y ∗ = 1.5 x (mole fraction units).

Solute removed from gas ≈ G ( y i n − y o u t ) = 100 ( 0.018 ) = 1.8 m o l / s G(y_{\mathrm{in}}-y_{\mathrm{out}}) = 100(0.018) = 1.8\,\mathrm{mol/s} G ( y in ​ − y out ​ ) = 100 ( 0.018 ) = 1.8 mol/s .

If outlet liquid is at equilibrium with inlet gas (limiting pinch idea for minimum L with rich end pinch): x o u t , m a x = y i n / 1.5 = 0.0133 x_{\mathrm{out,max}} = y_{\mathrm{in}}/1.5 = 0.0133 x out , max ​ = y in ​ /1.5 = 0.0133 .

Then L min ⁡ x o u t , m a x ≈ 1.8 L_{\min} x_{\mathrm{out,max}} \approx 1.8 L m i n ​ x out , max ​ ≈ 1.8 ⇒ L min ⁡ ≈ 1.8 / 0.0133 ≈ 135 m o l / s L_{\min} \approx 1.8/0.0133 \approx 135\,\mathrm{mol/s} L m i n ​ ≈ 1.8/0.0133 ≈ 135 mol/s (order-of-magnitude dilute material balance). Real designs take L > L min ⁡ L_{\min} L m i n ​ and account for non-dilute systems, heat effects, and kinetics (reactive amines).

Physical vs chemical absorption: physical solvents (e.g., cold methanol-type processes conceptually) rely on solubility; chemical solvents (amines for CO₂/H₂S) react with the solute, steepening effective capacity—still limited by rates, heats of reaction, and regeneration energy.

Stripping (Desorption)

Stripping removes a dissolved solute from a liquid by contact with a gas that has low solute partial pressure (steam, air, nitrogen, or fuel gas).

  • Feature Absorption Stripping
  • Solute direction Gas → liquid Liquid → gas
  • Liquid at top Lean (wants solute) Rich (has solute to remove)
  • Gas role Source of solute Sink for solute

Driving force y > y ∗ ( x ) y > y^*(x) y > y ∗ ( x ) y < y ∗ ( x ) y < y^*(x) y < y ∗ ( x ) (gas leaner than equilibrium with liquid)

Classic pair Absorber Regenerator / stripper

Amine plant loop (conceptual): absorber takes acid gas into lean amine → rich amine → stripper (steam/reboiler) releases acid gas → lean amine recycles. The stripper is desorption driven by high T (lower solubility / reverse reaction) and stripping vapor.

Sour water strippers and wastewater air strippers use the same logic: reduce liquid concentration of NH₃, H₂S, or VOCs. Raising T, lowering P, or increasing strip-gas rate improves removal when equilibrium and rates allow.

Exam trap: stripping is not distillation, though a stripper column may look similar. Distillation uses vapor generated from the same mixture (boilup) and reflux of condensate; stripping emphasizes an external or generated strip gas to lower solute partial pressure above the liquid.

Liquid–Liquid Extraction (LLE)

Liquid–liquid extraction transfers a solute from one liquid phase (the feed , often aqueous or organic) into a second immiscible liquid solvent .

  • Term Definition
  • Feed Liquid containing solute to be recovered or removed
  • Solvent Immiscible liquid that preferentially dissolves the solute
  • Extract Solvent phase after uptake of solute (solute-rich solvent phase)
  • Raffinate Feed phase after solute depletion

Partition / distribution coefficient K D = c s o l u t e , e x t r a c t / c s o l u t e , r a f f i n a t e K_D = c_{\mathrm{solute,extract}}/c_{\mathrm{solute,raffinate}} K D ​ = c solute , extract ​ / c solute , raffinate ​ at equilibrium (definitions vary by units)

Selectivity Preference for solute over other feed components

Single-stage mixer-settler: mix → settle → separate extract and raffinate. Multistage countercurrent trains or columns improve recovery—same staging logic as absorption (operating line vs equilibrium).

When partition helps

If K D K_D K D ​ is large, solute prefers the extract phase; fewer stages and less solvent achieve a target recovery. If phases partially miscible, solvent recovery and phase splitting become design constraints (tie lines on ternary diagrams—recognize existence, not draw full diagrams on this exam).

Worked partition sketch

Feed: 100 kg with 5 kg solute (5 wt%). Equal mass solvent, single equilibrium contact, K D = 4 K_D = 4 K D ​ = 4 on mass-fraction basis in each phase (simplified), immiscible solvents of constant mass 100 kg each after split.

Let raffinate solute mass fraction = x, extract = 4x (if K_D = y/x = 4 and phases equal mass… careful: with equal phase masses, solute balance: 5 = 100 x + 100 ( 4 x ) = 500 x ⇒ x = 0.01 , y = 0.04 5 = 100x + 100(4x) = 500x \Rightarrow x = 0.01,\quad y = 0.04 5 = 100 x + 100 ( 4 x ) = 500 x ⇒ x = 0.01 , y = 0.04

Solute in raffinate = 1 kg; in extract = 4 kg → 80% recovery in one stage. A second countercurrent stage would recover more of the remaining 1 kg.

When Each Operation Is Preferred Industrially

  • Situation Prefer Why
  • Dilute solute in a noncondensable gas Absorption Distillation of huge inert gas flows is impractical

Need to regenerate solvent / remove dissolved gas from liquid Stripping Reverse absorption; closes solvent loop

Close-boiling liquids, azeotropes, or heat-sensitive solutes with good solvent Extraction (then maybe distill solvent) Avoids extreme reflux or thermal damage

  • Wide boiling difference, thermally stable Distillation (Section 9.2) No foreign solvent to recover
  • Acid gas treating in natural gas Absorption + strip regeneration Chemical/physical solvents standard
  • Metals, pharmaceuticals, aromatics from dilute aqueous Extraction High selectivity solvents

Solvent selection checklist (absorption or extraction):

  • High capacity / favorable equilibrium for the solute
  • Selectivity against unwanted components
  • Easy regeneration (strip, distill, or crystallize)
  • Low toxicity, corrosion, vapor pressure, cost
  • Immiscibility (for LLE) and density difference for settling
  • Connecting Rate and Equilibrium Across Separators
  • Operation Equilibrium backbone Rate backbone
  • Distillation VLE (K, α) Stage efficiency, packing HTU, reflux traffic
  • Absorption Solubility / Henry / reactive capacity Two-film, k_G a, L/G
  • Stripping Same as absorption, reverse driving force Same coefficients; steam rate / T
  • Extraction Partition, selectivity, mutual solubility Drop size, mixer energy, settler area

Material balances still rule: overall and component balances close every absorber, stripper, and extractor—just as in Domain A. Never compute a rate coefficient when the stem only needs a balance or an equilibrium loading.

Common UPDA Traps

Calling lean solvent “rich” after the absorber bottom— rich leaves the bottom.

Claiming stripping changes the thermodynamic K of a reaction the way a catalyst does—different concepts.

Confusing raffinate (depleted feed phase) with extract (solvent phase).

Designing absorption with L < L_min (pinch—impossible for target recovery at finite height).

Using distillation intuition (reflux ratio) without mapping to L/G or solvent rate analogies.

Ignoring that chemical solvents need regeneration energy —absorption is not free separation.

Domain C Mass-Transfer Wrap (Chapter 9)

  • Section Core skill
  • 9.1 Fick, k and driving forces, film / two-film
  • 9.2 α, reflux, stages/packing, condenser type, McCabe–Thiele logic
  • 9.3 Absorb / strip / extract roles, lean–rich, raffinate–extract, selection

Together with fluid mechanics and heat transfer (Chapters 7–8), this completes the transport-phenomena third of Domain C for the UPDA/MMUP Chemical exam. Domain D next turns from physical separations to chemical reaction engineering —rates that create or destroy species rather than only redistribute them between phases.