Study guide

2.2 Stoichiometry, Limiting and Excess Reactants

UPDA/MMUP Engineer Registration Exam — Chemical Qatar

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts and Format 1.2 Registration, Eligibility, Grades, and Renewal 1.3 Study Strategy and Exam-Day Tactics

2 Stoichiometry & Process Calculation Foundations

2.1 Units, Bases, and Process Variables 2.2 Stoichiometry, Limiting and Excess Reactants 2.3 Batch vs Continuous and Steady vs Unsteady Operation

3 Material Balances

3.1 Steady Material Balances Without Reaction 3.2 Material Balances With Chemical Reaction 3.3 Recycle, Bypass, and Purge Systems

4 Energy Balances

4.1 Energy Forms and the First Law for Processes 4.2 Heats of Reaction and Formation 4.3 Process Energy Balance Applications

5 Thermodynamics Fundamentals

5.1 Thermodynamic Laws and State Functions 5.2 Equations of State and Real Gases 5.3 Enthalpy, Entropy, and Heat Capacity

6 Phase and Chemical Equilibria

6.1 Phase Equilibria and VLE Fundamentals 6.2 Bubble Point, Dew Point, and Flash Concepts 6.3 Chemical Reaction Equilibrium

7 Fluid Mechanics

7.1 Fluid Properties, Reynolds Number, and Flow Regimes 7.2 Bernoulli Equation and Mechanical Energy Balance 7.3 Pipe Flow, Friction, and Pumps

8 Heat Transfer

8.1 Conduction, Convection, and Radiation 8.2 Heat Transfer Coefficients and Overall U 8.3 Heat Exchangers and LMTD

9 Mass Transfer and Separations

9.1 Mass Transfer and Diffusion Fundamentals 9.2 Distillation Columns and Operations 9.3 Absorption, Stripping, and Extraction

10 Chemical Reaction Engineering

10.1 Rate Laws and Reaction Order 10.2 Arrhenius Equation and Temperature Effects 10.3 Batch and CSTR Reactors 10.4 PFR Design and Reactor Selection

11 Process Instrumentation and Control

11.1 Process Instrumentation and Measurement 11.2 Feedback Control and PID 11.3 Process Dynamics, Alarms, and Interlocks

12 Process Safety, Qatar Codes and Professional Conduct

12.1 Process Safety Fundamentals and Inherent Safety 12.2 HAZOP Methodology 12.3 LOPA, Relief Systems, and Emergency Response 12.4 Fire Protection, Environment, and Qatar Plant Context 12.5 Qatar Codes, Standards, and Professional Conduct

13 Engineering Economics and Cost Analysis

13.1 Cost Structures and Break-Even Analysis 13.2 Depreciation and the Time Value of Money 13.3 Project Economics, Estimating, and Cost Control

14 Project Management Principles (PMP)

14.1 PM Framework, Process Groups, and Knowledge Areas 14.2 Scope, Schedule, and Cost Management 14.3 Risk, Quality, and Stakeholder Management

2.2 Stoichiometry, Limiting and Excess Reactants

Key Takeaways Explain This Topic AI

Balance reactions on atoms first; then convert feed amounts to moles before applying stoichiometric ratios.

The limiting reactant is the species that would be fully consumed first if the reaction went to completion at the given stoichiometry.

Percent excess = (amount fed − amount required by stoichiometry based on the limiting reactant) / amount required × 100%.

Fractional conversion of A is moles of A reacted divided by moles of A fed; yield and selectivity compare desired product to other fates of reactant.

Never apply mass ratios as if they were mole ratios unless all species happen to share the same molecular weight.

Last updated: August 2026

Once units and stream variables are under control, reactive process calculations add one more layer: stoichiometry . Domain A of the UPDA/MMUP Chemical exam routinely tests whether you can identify the limiting reactant, compute conversion, and interpret yield or selectivity definitions under exam time pressure. The arithmetic is elementary, but the definitions are easy to mix up—especially when feeds are given by mass.

Balancing chemical equations

A balanced reaction conserves every element. For a A + b B → c C + d D , a\,\mathrm{A} + b\,\mathrm{B} \rightarrow c\,\mathrm{C} + d\,\mathrm{D}, a A + b B → c C + d D ,

the stoichiometric coefficients a , b , c , d a,b,c,d a , b , c , d are pure numbers (often reduced to integers). They define molar ratios only : n A , r e a c t e d a = n B , r e a c t e d b = n C , f o r m e d c = ξ , \frac{n_{\mathrm{A,\,reacted}}}{a} = \frac{n_{\mathrm{B,\,reacted}}}{b} = \frac{n_{\mathrm{C,\,formed}}}{c} = \xi, a n A , reacted ​ ​ = b n B , reacted ​ ​ = c n C , formed ​ ​ = ξ ,

where ξ \xi ξ is the extent of reaction (moles of reaction events). Extent is the cleanest bookkeeping variable for multi-reaction systems, but single-reaction UPDA items usually work directly with mole tables.

Procedure for any stoichiometry problem

Write and balance the reaction.

Convert all feed quantities to moles (or molar rates).

Divide each reactant’s available moles by its stoichiometric coefficient to find which reactant can support the fewest reaction extents—that reactant is limiting .

Compute theoretical product for complete conversion of the limiting reactant.

Apply the stated conversion, yield, or selectivity to get actual product and residual reactants.

Limiting reactant, excess reactant, and percent excess

Suppose feed supplies n A 0 n_{\mathrm{A0}} n A0 ​ and n B 0 n_{\mathrm{B0}} n B0 ​ moles of A and B for the reaction a A + b B → a\mathrm{A} + b\mathrm{B} \rightarrow a A + b B → products. The stoichiometric requirement of B for complete use of A is n B , r e q = n A 0 × b a . n_{\mathrm{B,\,req}} = n_{\mathrm{A0}} \times \frac{b}{a}. n B , req ​ = n A0 ​ × a b ​ .

If n B 0 < n B , r e q n_{\mathrm{B0}} < n_{\mathrm{B,\,req}} n B0 ​ < n B , req ​ , B is limiting and A is in excess.

If n B 0 > n B , r e q n_{\mathrm{B0}} > n_{\mathrm{B,\,req}} n B0 ​ > n B , req ​ , A is limiting and B is in excess.

Percent excess of B (when A is limiting) is % e x c e s s B = n B 0 − n B , r e q n B , r e q × 100 % . \%\,\mathrm{excess\,B} = \frac{n_{\mathrm{B0}} - n_{\mathrm{B,\,req}}}{n_{\mathrm{B,\,req}}} \times 100\%. % excess B = n B , req ​ n B0 ​ − n B , req ​ ​ × 100%.

Some exam writers give “20% excess air” for combustion; that means air moles fed are 1.20 times the stoichiometric air calculated for the fuel that actually reacts (or for complete fuel combustion—read carefully).

  • Quantity Definition (single reaction)
  • Limiting reactant Reactant with smallest (moles fed / stoichiometric coefficient)
  • Excess reactant Any reactant fed above stoichiometric requirement based on the limiting reactant
  • Theoretical product Product moles if limiting reactant reacts completely with 100% selectivity

Fractional conversion of A X A = ( n A 0 − n A ) / n A 0 X_A = (n_{\mathrm{A0}} - n_A)/n_{\mathrm{A0}} X A ​ = ( n A0 ​ − n A ​ ) / n A0 ​

  • Yield of P from A Often (moles A → P) / (moles A fed) or / (moles A reacted)—definition must match the problem
  • Selectivity (P vs U) (moles A → desired P) / (moles A → undesired U), or product mole ratio forms

Yield and selectivity wording varies. Before computing, underline whether the denominator is “A fed,” “A reacted,” or “theoretical maximum P.” UPDA-style MCQs often hinge on that single phrase.

Fractional conversion

For reactant A: X A = moles of A reacted moles of A fed = n A 0 − n A n A 0 . X_A = \frac{\text{moles of A reacted}}{\text{moles of A fed}} = \frac{n_{\mathrm{A0}} - n_A}{n_{\mathrm{A0}}}. X A ​ = moles of A fed moles of A reacted ​ = n A0 ​ n A0 ​ − n A ​ ​ .

Conversion is defined for a reactant , not for a product. Saying “50% conversion of product” is meaningless. In a continuous reactor, use molar flow rates n ˙ \dot{n} n ˙ with the same formula. Incomplete conversion leaves unreacted limiting reactant in the outlet even if another species was fed in excess.

Worked example 1 — Limiting reactant and percent excess

Ammonia is produced by N 2 + 3 H 2 → 2 N H 3 \mathrm{N_2} + 3\mathrm{H_2} \rightarrow 2\mathrm{NH_3} N 2 ​ + 3 H 2 ​ → 2 N H 3 ​ . A feed contains 100 kmol/h N₂ and 250 kmol/h H₂. Identify the limiting reactant, the percent excess of the other reactant, and the maximum NH₃ production rate if conversion of the limiting reactant is 100%.

Solution. Required H₂ for 100 kmol/h N₂: 100 × 3 = 300 k m o l / h 100 \times 3 = 300\,\mathrm{kmol/h} 100 × 3 = 300 kmol/h . Only 250 kmol/h H₂ is available, so H₂ is limiting and N₂ is in excess.

N₂ required by the available H₂: 250 × ( 1 / 3 ) = 83.33 k m o l / h 250 \times (1/3) = 83.33\,\mathrm{kmol/h} 250 × ( 1/3 ) = 83.33 kmol/h . % e x c e s s N 2 = 100 − 83.33 83.33 × 100 % = 20 % . \%\,\mathrm{excess\,N_2} = \frac{100 - 83.33}{83.33} \times 100\% = 20\%. % excess N 2 ​ = 83.33 100 − 83.33 ​ × 100% = 20%.

Maximum NH₃ at complete H₂ conversion: 250 × ( 2 / 3 ) = 166.7 k m o l / h 250 \times (2/3) = 166.7\,\mathrm{kmol/h} 250 × ( 2/3 ) = 166.7 kmol/h .

If someone wrongly treated N₂ as limiting because “less N₂ is fed,” they would report 200 kmol/h NH₃ and miss the answer. Always compare moles-fed-per-coefficient: N₂ → 100 / 1 = 100 100/1 = 100 100/1 = 100 ; H₂ → 250 / 3 = 83.3 250/3 = 83.3 250/3 = 83.3 ; smaller number wins (H₂).

Worked example 2 — Conversion with excess air (combustion style)

Carbon burns: C + O 2 → C O 2 \mathrm{C} + \mathrm{O_2} \rightarrow \mathrm{CO_2} C + O 2 ​ → C O 2 ​ . Feed: 50 kmol C/h with 20% excess air. Air is 21 mol% O₂ and 79 mol% N₂. Assume complete conversion of carbon. Find O₂ fed, N₂ fed, and dry product composition.

Solution. Stoichiometric O₂ = 50 kmol/h. With 20% excess: O 2 f e d = 1.20 × 50 = 60 k m o l / h . \mathrm{O_2\,fed} = 1.20 \times 50 = 60\,\mathrm{kmol/h}. O 2 ​ fed = 1.20 × 50 = 60 kmol/h .

Air fed = 60 / 0.21 = 285.7 k m o l / h 60 / 0.21 = 285.7\,\mathrm{kmol/h} 60/0.21 = 285.7 kmol/h ; N₂ fed = 0.79 × 285.7 = 225.7 k m o l / h 0.79 \times 285.7 = 225.7\,\mathrm{kmol/h} 0.79 × 285.7 = 225.7 kmol/h .

After complete C combustion: CO₂ = 50, O₂ remaining = 60 − 50 = 10 60 - 50 = 10 60 − 50 = 10 , N₂ = 225.7 (inert). Dry product total = 50 + 10 + 225.7 = 285.7 k m o l / h 50 + 10 + 225.7 = 285.7\,\mathrm{kmol/h} 50 + 10 + 225.7 = 285.7 kmol/h .

Mole fractions (dry): CO₂ 0.175, O₂ 0.035, N₂ 0.790.

Worked example 3 — Yield and selectivity

Reactant A can form desired P or undesired U: A → P , A → U . \mathrm{A} \rightarrow \mathrm{P}, \qquad \mathrm{A} \rightarrow \mathrm{U}. A → P , A → U .

Feed 100 mol A; outlet: 40 mol A, 45 mol P, 15 mol U. Find conversion of A, yield of P based on A fed, and selectivity of P relative to U.

Solution. A reacted = 100 − 40 = 60 100 - 40 = 60 100 − 40 = 60 mol → X A = 0.60 X_A = 0.60 X A ​ = 0.60 .

Yield of P on A fed = 45 / 100 = 0.45 45/100 = 0.45 45/100 = 0.45 (45%).

Selectivity S P / U = 45 / 15 = 3.0 S_{P/U} = 45/15 = 3.0 S P / U ​ = 45/15 = 3.0 (moles P per mole U).

Note yield based on A reacted would be 45 / 60 = 0.75 45/60 = 0.75 45/60 = 0.75 —a different number. MCQ stems that omit the basis of yield are incomplete; when both definitions appear as options, read the stem’s exact wording.

Worked example 4 — Mass trap

The reaction 2 H 2 + O 2 → 2 H 2 O 2\mathrm{H_2} + \mathrm{O_2} \rightarrow 2\mathrm{H_2O} 2 H 2 ​ + O 2 ​ → 2 H 2 ​ O is run with 4 kg H₂ and 32 kg O₂. Who is limiting?

Solution in moles: H₂ = 4 / 2 = 2 k m o l 4/2 = 2\,\mathrm{kmol} 4/2 = 2 kmol ; O₂ = 32 / 32 = 1 k m o l 32/32 = 1\,\mathrm{kmol} 32/32 = 1 kmol . Stoichiometric need: 2 kmol H₂ requires 1 kmol O₂—exact stoichiometric feed, neither excess. If you compared 4 kg vs 32 kg by mass alone, you would falsely call H₂ limiting. Always convert to moles first.

Exam traps to memorize

Mass used as moles — especially with light gases (H₂, He) or heavy organics.

Wrong limiting reactant — forgetting to divide by stoichiometric coefficients.

% excess based on wrong reactant — excess is relative to the stoichiometric partner of the limiting species.

Conversion applied to excess reactant — conversion statements usually refer to the limiting reactant or a named species; apply X X X only to that species.

Yield vs selectivity confusion — yield compares product to reactant; selectivity compares product pathways.

Unbalanced equation — one missing atom invalidates every ratio downstream.

Master these definitions now; Chapter 3 will embed them inside multi-unit material balances with recycle and purge, where a single stoichiometry error propagates through the entire flowsheet.