Study guide
3.2 Ammonia Hazards and Flammability
RETA Certified Assistant Refrigeration Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Refrigeration Fundamentals
1.1 Heat, Temperature, and Pressure 1.2 Ton of Refrigeration and Temperature Ranges 1.3 Superheat and Subcooling
2 Chapter 2: Refrigeration Cycle
2.1 Vapor-Compression Cycle Flow and Components 2.2 Heat Rejection Balance and Expansion Devices 2.3 Cascade Systems and Intercoolers
3 Chapter 3: Properties of Refrigerants
3.1 Ammonia (R-717) Basics and Physical Properties 3.2 Ammonia Hazards and Flammability 3.3 Industrial Comparison and Efficiency
4 Chapter 4: Saturated Refrigerant Tables
4.1 Saturated Ammonia P-T Tables
5 Chapter 5: Types of Compressors
5.1 Industrial Compressor Types
6 Chapter 6: Operation and Maintenance of Compressors
6.1 Compressor Construction and Unloaders 6.2 Compression Ratio and Volumetric Efficiency 6.3 Compressor Startup and Operating Parameters 6.4 Compressor Troubleshooting and Slugging
7 Chapter 7: Lubrication
7.1 Lubrication Principles and Oil Types 7.2 Oil Separators and Net Oil Pressure 7.3 Low-Side Oil Logging and Management 7.4 Safe Oil Draining and Charging Procedures
8 Chapter 8: Evaporators and Cooling Units
8.1 DX vs Flooded Evaporators 8.2 TXV Behavior and Control 8.3 Defrost Systems and Evaporator Maintenance
9 Chapter 9: Condensers and High-Pressure Receivers
9.1 Condenser Types and Operation 9.2 High-Pressure Receivers and King Valves 9.3 Safety Relief Valves and Charging
10 Chapter 10: Purging
10.1 Non-Condensable Gases and Ingress 10.2 Purger Operation and Verification
11 Chapter 11: Safety, Hazards, and Prevention
11.1 Regulatory Oversight: OSHA PSM and EPA RMP 11.2 Industry Codes: IIAR Standards 11.3 Ammonia Exposure Limits and First Aid 11.4 Engine Room Safety Systems
3.2 Ammonia Hazards and Flammability
Key Takeaways Explain This Topic AI
Ammonia is classified as an ASHRAE safety group B2L refrigerant due to its high toxicity and lower flammability with a slow burning velocity.
Ammonia is highly corrosive to yellow metals (copper, brass, bronze, and zinc) in the presence of moisture, requiring steel or aluminum system construction.
The flammability limits of ammonia in air are 15% to 28% by volume; it requires a high-energy ignition source and a temperature of 1,204°F (651°C) to ignite.
Explosion hazards are dramatically elevated in confined spaces or when ammonia vapor mixes with compressor oil mist, which lowers the ignition energy required.
The GHS classification for ammonia includes Category 2 Flammable Gas, Category 3 Inhalation Toxicity, Category 1B Skin Corrosion, and Category 1 Aquatic Hazard.
Last updated: July 2026
3.2 Ammonia Hazards and Flammability
While anhydrous ammonia (R-717) is an excellent thermodynamic choice, it presents substantial physical and health hazards. Operators must understand these hazards, flammability thresholds, and compatibility limits to manage the system safely. This section covers toxicity, GHS classifications, material compatibility, flammability limits, and explosive conditions.
Toxicity and Physiological Effects
Unlike standard halocarbon refrigerants, which are generally classified as non-toxic (ASHRAE Safety Group A), ammonia is classified as a toxic gas under ASHRAE Safety Group B (specifically B2L ). The "B" indicates high toxicity, "2" indicates moderate flammability, and "L" indicates a low burning velocity.
Ammonia is highly hydrophilic (water-seeking). When it contacts moisture, it reacts to form ammonium hydroxide ( NH 4 OH \text{NH}_4\text{OH} NH 4 OH ), a strong alkaline compound. This chemical reaction occurs instantly upon contact with moist human tissues, including the eyes, skin, and respiratory tract. Unlike acids, which cause coagulative necrosis that limits penetration, alkalies cause liquefactive necrosis, which dissolves tissue proteins and penetrates deeply, resulting in severe chemical burns.
Physiological effects at various concentrations in air include:
5 to 50 ppm: Easily detectable odor; no immediate hazard.
50 ppm: OSHA Permissible Exposure Limit (PEL) for an 8-hour time-weighted average (TWA). Mild eye and throat irritation begins.
150 ppm: Mild eye, nose, and throat irritation; tolerable for only short periods.
300 ppm: NIOSH Immediately Dangerous to Life or Health (IDLH) threshold. Immediate respiratory distress, intense coughing, and potential lung damage. SCBA (Self-Contained Breathing Apparatus) is mandatory above this level.
1,000 to 2,000 ppm: Severe skin and eye irritation, blindness, throat swelling, and asphyxiation within minutes.
5,000 ppm and above: Rapid respiratory arrest, severe chemical burns, and death.
Corrosivity to Yellow Metals
Anhydrous ammonia is chemically compatible with standard structural metals such as carbon steel, stainless steel, aluminum, and cast iron. However, ammonia is extremely corrosive to copper, brass, bronze, zinc, and galvanized coatings (often referred to collectively as "yellow metals").
In a completely dry, anhydrous state, ammonia's reaction with copper is slow. However, industrial systems inevitably contain trace amounts of moisture. When moisture is present, ammonia reacts with the copper to form a soluble copper-ammonium complex ( [ Cu ( NH 3 ) 4 ] 2 + [\text{Cu}(\text{NH}_3)_4]^{2+} [ Cu ( NH 3 ) 4 ] 2 + ), which rapidly dissolves and corrodes the metal. This corrosion can lead to structural failure, pipe ruptures, and toxic leaks.
Design Rules:
No copper or brass piping, valves, or fittings may be used in an ammonia system.
Hermetic or semi-hermetic compressors used in halocarbon systems contain copper motor windings that are cooled by the suction gas. Because ammonia destroys copper, standard hermetic compressors cannot be used. Ammonia compressors must be open-drive types (where the motor is separate and drives the compressor via a shaft seal) or use specialized hermetic motors with aluminum windings or protective canned barriers.
Flammability Limits in Air
Although ammonia is difficult to ignite and is often considered non-flammable in standard transport, it does burn. Its flammability limits in air are:
- Lower Flammability Limit (LFL): 15% by volume (150,000 ppm)
- Upper Flammability Limit (UFL): 28% by volume (280,000 ppm)
For ignition to occur within this range, a high-energy ignition source (such as an open flame, electrical arc, or static spark) must be present, and the mixture must reach an auto-ignition temperature of approximately 1,204°F (651°C) .
Conditions Enhancing Explosion Hazards
Under normal open-air conditions, ammonia is unlikely to explode because the gas rises and dissipates rapidly, keeping concentrations below the 15% LFL. However, in industrial operations, two critical factors can cause ammonia to become highly explosive:
1. Confined Spaces
If a leak occurs inside a confined space—such as an unventilated machinery room, a ceiling plenum, a cold storage room, or a vessel enclosure—the ammonia concentration can quickly build up into the 15% to 28% flammability range. If an electrical contactor arcs or a tool strikes a spark in this environment, a catastrophic explosion can occur.
2. Presence of Lubricating Oil
Industrial ammonia systems require lubricating oil for compressor operation (typically mineral oil or synthetic polyalphaolefin). Ammonia is not miscible with mineral oil, meaning the oil tends to carry over into the piping and high-side components. If a leak occurs, the escaping mixture consists of ammonia vapor and a fine mist of compressor oil. The presence of oil droplets dramatically lowers the energy required for ignition and lowers the LFL of the mixture. The oil acts as a fuel binder, turning a hard-to-ignite gas into a highly explosive aerosol.
SDS Classifications and GHS Pictograms
Under the Globally Harmonized System of Classification and Labelling of Chemicals (GHS), ammonia is classified under several critical hazard categories, which are documented in the facility's Safety Data Sheet (SDS):
- Flammable Gases: Category 2 (Moderate flammability)
- Gases Under Pressure: Liquefied gas
- Acute Toxicity (Inhalation): Category 3 (Toxic if inhaled)
- Skin Corrosion: Category 1B (Causes severe skin burns)
- Serious Eye Damage: Category 1 (Causes serious eye damage)
- Acute/Chronic Aquatic Hazard: Category 1 (Very toxic to aquatic life)
The SDS requires specific GHS pictograms on ammonia storage vessels and facility entrances: the Corrosive pictogram (showing chemicals pouring onto skin/metal), the Toxic/Skull and Crossbones pictogram (indicating acute toxicity), the Gas Cylinder pictogram (indicating gas under pressure), and the Environmental Hazard pictogram (showing a dead fish and tree).
Emergency Safety Systems
To mitigate flammability and toxicity risks, industrial machinery rooms must feature active safety systems designed in accordance with IIAR 2 standards:
Ammonia Detectors: Continuous monitoring sensors located in the engine room. At 25 ppm , they must trigger local alarms and alert operators. At 150 ppm , they must activate emergency mechanical ventilation. At 40,000 ppm (25% of the LFL), they must trigger the Emergency Shutdown (ESD) system, de-energizing all non-emergency electrical equipment (including compressors) to eliminate potential ignition sources.
Emergency Ventilation: Exhaust fans must be capable of moving air at rates specified by code to rapidly dilute vapor concentrations below the LFL and exhaust the air to a safe outdoor location.